| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAHfPSqCFAVb71kMYAVoZJphiUtSoTUP2yD=Jw1+GBu-n10kVBA@mail.gmail.com>
Date: Fri, 28 Dec 2012 22:06:47 +0530
From: Naveen Krishna Ch <naveenkrishna.ch@...il.com>
To: Naveen Krishna Chatradhi <ch.naveen@...sung.com>
Cc: linux-i2c@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-samsung-soc@...r.kernel.org,
devicetree-discuss@...ts.ozlabs.org, kgene.kim@...sung.com,
grant.likely@...retlab.ca, w.sang@...gutronix.de,
linux-kernel@...r.kernel.org, taeggyun.ko@...sung.com,
balbi@...com, thomas.abraham@...aro.org
Subject: Re: [PATCH v3] i2c: exynos5: add High Speed I2C controller driver
On 28 December 2012 16:57, Naveen Krishna Chatradhi
<ch.naveen@...sung.com> wrote:
> Adds support for High Speed I2C driver found in Exynos5 and later
> SoCs from Samsung. This driver currently supports Auto mode.
>
> Driver only supports Device Tree method of passing platform data.
> Note: Added debugfs support for registers view, not tested.
>
> Signed-off-by: Taekgyun Ko <taeggyun.ko@...sung.com>
> Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@...sung.com>
> ---
> Changes since v2: fixed comments from Felipe Balbi.
> And minor fixes for the return values in exynos5_i2c_doxfer()
>
> drivers/i2c/busses/Kconfig | 7 +
> drivers/i2c/busses/Makefile | 1 +
> drivers/i2c/busses/i2c-exynos5.c | 736 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 744 insertions(+)
> create mode 100644 drivers/i2c/busses/i2c-exynos5.c
>
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index bdca511..4caea76 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -618,6 +618,13 @@ config I2C_S3C2410
> Say Y here to include support for I2C controller in the
> Samsung SoCs.
>
> +config I2C_EXYNOS5
> + tristate "Exynos5 high-speed I2C driver"
> + depends on ARCH_EXYNOS5
> + help
> + Say Y here to include support for High-speed I2C controller in the
> + Exynos5 based Samsung SoCs.
> +
> config I2C_S6000
> tristate "S6000 I2C support"
> depends on XTENSA_VARIANT_S6000
> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index 6181f3f..4b1548c 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -61,6 +61,7 @@ obj-$(CONFIG_I2C_PUV3) += i2c-puv3.o
> obj-$(CONFIG_I2C_PXA) += i2c-pxa.o
> obj-$(CONFIG_I2C_PXA_PCI) += i2c-pxa-pci.o
> obj-$(CONFIG_I2C_S3C2410) += i2c-s3c2410.o
> +obj-$(CONFIG_I2C_EXYNOS5) += i2c-exynos5.o
> obj-$(CONFIG_I2C_S6000) += i2c-s6000.o
> obj-$(CONFIG_I2C_SH7760) += i2c-sh7760.o
> obj-$(CONFIG_I2C_SH_MOBILE) += i2c-sh_mobile.o
> diff --git a/drivers/i2c/busses/i2c-exynos5.c b/drivers/i2c/busses/i2c-exynos5.c
> new file mode 100644
> index 0000000..a5eb959
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-exynos5.c
> @@ -0,0 +1,736 @@
> +/**
> + * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver
> + *
> + * Copyright (C) 2012 Samsung Electronics Co., Ltd.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/debugfs.h>
> +
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/time.h>
> +#include <linux/interrupt.h>
> +#include <linux/delay.h>
> +#include <linux/errno.h>
> +#include <linux/err.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/clk.h>
> +#include <linux/slab.h>
> +#include <linux/io.h>
> +#include <linux/of_address.h>
> +#include <linux/of_gpio.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_i2c.h>
> +
> +/* Register Map */
> +#define HSI2C_CTL 0x00
> +#define HSI2C_FIFO_CTL 0x04
> +#define HSI2C_TRAILIG_CTL 0x08
> +#define HSI2C_CLK_CTL 0x0C
> +#define HSI2C_CLK_SLOT 0x10
> +#define HSI2C_INT_ENABLE 0x20
> +#define HSI2C_INT_STATUS 0x24
> +#define HSI2C_ERR_STATUS 0x2C
> +#define HSI2C_FIFO_STATUS 0x30
> +#define HSI2C_TX_DATA 0x34
> +#define HSI2C_RX_DATA 0x38
> +#define HSI2C_CONF 0x40
> +#define HSI2C_AUTO_CONF 0x44
> +#define HSI2C_TIMEOUT 0x48
> +#define HSI2C_MANUAL_CMD 0x4C
> +#define HSI2C_TRANS_STATUS 0x50
> +#define HSI2C_TIMING_HS1 0x54
> +#define HSI2C_TIMING_HS2 0x58
> +#define HSI2C_TIMING_HS3 0x5C
> +#define HSI2C_TIMING_FS1 0x60
> +#define HSI2C_TIMING_FS2 0x64
> +#define HSI2C_TIMING_FS3 0x68
> +#define HSI2C_TIMING_SLA 0x6C
> +#define HSI2C_ADDR 0x70
> +
> +/* I2C_CTL Register bits */
> +#define HSI2C_FUNC_MODE_I2C (1u << 0)
> +#define HSI2C_MASTER (1u << 3)
> +#define HSI2C_RXCHON (1u << 6)
> +#define HSI2C_TXCHON (1u << 7)
> +#define HSI2C_SW_RST (1u << 31)
> +
> +/* I2C_FIFO_CTL Register bits */
> +#define HSI2C_RXFIFO_EN (1u << 0)
> +#define HSI2C_TXFIFO_EN (1u << 1)
> +#define HSI2C_TXFIFO_TRIGGER_LEVEL (0x20 << 16)
> +#define HSI2C_RXFIFO_TRIGGER_LEVEL (0x20 << 4)
> +
> +/* I2C_TRAILING_CTL Register bits */
> +#define HSI2C_TRAILING_COUNT (0xf)
> +
> +/* I2C_INT_EN Register bits */
> +#define HSI2C_INT_TX_ALMOSTEMPTY_EN (1u << 0)
> +#define HSI2C_INT_RX_ALMOSTFULL_EN (1u << 1)
> +#define HSI2C_INT_TRAILING_EN (1u << 6)
> +#define HSI2C_INT_I2C_EN (1u << 9)
> +
> +/* I2C_FIFO_STAT Register bits */
> +#define HSI2C_RX_FIFO_EMPTY (1u << 24)
> +#define HSI2C_RX_FIFO_FULL (1u << 23)
> +#define HSI2C_RX_FIFO_LEVEL_MASK (0x7 << 16)
> +#define HSI2C_TX_FIFO_EMPTY (1u << 8)
> +#define HSI2C_TX_FIFO_FULL (1u << 7)
> +#define HSI2C_TX_FIFO_LEVEL_MASK (0x7 << 7)
> +#define HSI2C_FIFO_EMPTY (0x1000100)
> +
> +/* I2C_CONF Register bits */
> +#define HSI2C_AUTO_MODE (1u << 31)
> +#define HSI2C_10BIT_ADDR_MODE (1u << 30)
> +#define HSI2C_HS_MODE (1u << 29)
> +
> +/* I2C_AUTO_CONF Register bits */
> +#define HSI2C_READ_WRITE (1u << 16)
> +#define HSI2C_STOP_AFTER_TRANS (1u << 17)
> +#define HSI2C_MASTER_RUN (1u << 31)
> +
> +/* I2C_TIMEOUT Register bits */
> +#define HSI2C_TIMEOUT_EN (1u << 31)
> +
> +/* I2C_TRANS_STATUS register bits */
> +#define HSI2C_MASTER_BUSY (1u << 17)
> +#define HSI2C_SLAVE_BUSY (1u << 16)
> +#define HSI2C_NO_DEV (1u << 3)
> +#define HSI2C_NO_DEV_ACK (1u << 2)
> +#define HSI2C_TRANS_ABORT (1u << 1)
> +#define HSI2C_TRANS_DONE (1u << 0)
> +
> +/**
> + * Although exynos5 supports max HS-IIC speed of 3.4Mhz,
> + * but currently we are facing booting issues beyond 1Mhz
> + * So limiting HS-IIC bus speed to 1Mhz
> +*/
> +#define HSI2C_HS_TX_CLOCK 1000000
> +#define HSI2C_FS_TX_CLOCK 400000
> +
> +#define HSI2C_FAST_SPD 0
> +#define HSI2C_HIGH_SPD 1
> +
> +#define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(1000))
> +
> +/* timeout for pm runtime autosuspend */
> +#define EXYNOS5_I2C_PM_TIMEOUT 1000 /* ms */
> +
> +struct exynos5_i2c {
> + struct i2c_adapter adap;
> + unsigned int suspended:1;
> +
> + struct i2c_msg *msg;
> + unsigned int msg_idx;
> + struct completion msg_complete;
> + unsigned int msg_ptr;
> +
> + unsigned int irq;
> +
> + void __iomem *regs;
> + struct clk *clk;
> + struct device *dev;
> + int gpios[2];
> +
> + int bus_num;
> + int speed_mode;
> + struct dentry *debugfs_root;
> +};
> +
> +static const struct of_device_id exynos5_i2c_match[] = {
> + { .compatible = "samsung,exynos5-hsi2c" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, exynos5_i2c_match);
> +
> +static void exynos5_i2c_stop(struct exynos5_i2c *i2c, int err)
> +{
> + dev_vdbg(i2c->dev, "STOP\n");
> +
> + i2c->msg_idx++;
> + if (err)
> + i2c->msg_idx = err;
> +
> + /* Disable interrrupts */
> + writel(0, i2c->regs + HSI2C_INT_ENABLE);
> + complete(&i2c->msg_complete);
> +}
> +
> +static void exynos5_i2c_en_timeout(struct exynos5_i2c *i2c)
> +{
> + unsigned long i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT);
> +
> + /* Clear to enable Timeout */
> + i2c_timeout &= ~HSI2C_TIMEOUT_EN;
> + writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT);
> +}
> +
> +static void exynos5_i2c_master_run(struct exynos5_i2c *i2c)
> +{
> + /* Start data transfer in Master mode */
> + u32 i2c_auto_conf = readl(i2c->regs + HSI2C_AUTO_CONF);
> + i2c_auto_conf |= HSI2C_MASTER_RUN;
> + writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
> +}
> +
> +/**
> + * exynos5_i2c_set_bus: get the i2c bus for a master transaction
> +*/
> +static int exynos5_i2c_set_master(struct exynos5_i2c *i2c)
> +{
> + unsigned long t_status;
> + int timeout = 400;
> +
> + while (timeout-- > 0) {
> + t_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
> +
> + if (!(t_status & HSI2C_MASTER_BUSY))
> + return 0;
> +
> + msleep(20);
> + }
> +
> + return -ETIMEDOUT;
> +}
> +
> +/**
> + * exynos5_i2c_irq: top level IRQ servicing routine
> +*/
> +static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
> +{
> + struct exynos5_i2c *i2c = dev_id;
> + unsigned long t_stat;
> + unsigned char byte;
> +
> + t_stat = readl(i2c->regs + HSI2C_TRANS_STATUS);
> +
> + if (t_stat & HSI2C_TRANS_ABORT) {
> + /* deal with arbitration loss */
> + dev_err(i2c->dev, "deal with arbitration loss\n");
> + goto out;
> + }
> + if (i2c->msg->flags & I2C_M_RD) {
> + if (t_stat & HSI2C_TRANS_DONE) {
> + dev_dbg(i2c->dev, "Device found.");
> + while ((readl(i2c->regs + HSI2C_FIFO_STATUS) &
> + HSI2C_RX_FIFO_EMPTY) == 0) {
> + byte = readl(i2c->regs + HSI2C_RX_DATA);
> + dev_dbg(i2c->dev, "read rx_data = %x", byte);
> + i2c->msg->buf[i2c->msg_ptr++] = byte;
> + }
> +
> + if (i2c->msg_ptr >= i2c->msg->len)
> + exynos5_i2c_stop(i2c, 0);
> +
> + } else if (t_stat & HSI2C_NO_DEV) {
> + dev_dbg(i2c->dev, "No device found.");
> + exynos5_i2c_stop(i2c, -ENXIO);
> + } else if (t_stat & HSI2C_NO_DEV_ACK &&
> + !(i2c->msg->flags & I2C_M_IGNORE_NAK)) {
> + dev_dbg(i2c->dev, "No device Ack.");
> + exynos5_i2c_stop(i2c, -ENXIO);
> + }
> + } else {
> + byte = i2c->msg->buf[i2c->msg_ptr++];
> + dev_dbg(i2c->dev, "write tx_data = %x ", byte);
> + writel(byte, i2c->regs + HSI2C_TX_DATA);
> +
> + if (i2c->msg_ptr >= i2c->msg->len)
> + exynos5_i2c_stop(i2c, 0);
> + }
> +
> + out:
> + /* Set those bits to clear them */
> + writel(readl(i2c->regs + HSI2C_INT_STATUS),
> + i2c->regs + HSI2C_INT_STATUS);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static void exynos5_i2c_message_start(struct exynos5_i2c *i2c,
> + struct i2c_msg *msgs)
> +{
> + unsigned long usi_ctl = HSI2C_FUNC_MODE_I2C | HSI2C_MASTER;
> + unsigned long i2c_auto_conf;
> + unsigned long i2c_addr = ((msgs->addr & 0x7f) << 10);
> + unsigned long usi_int_en = 0;
> +
> + exynos5_i2c_en_timeout(i2c);
> +
> + if (msgs->flags & I2C_M_RD) {
> + usi_ctl &= ~HSI2C_TXCHON;
> + usi_ctl |= HSI2C_RXCHON;
> +
> + i2c_auto_conf |= HSI2C_READ_WRITE;
> +
> + usi_int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN |
> + HSI2C_INT_TRAILING_EN);
> + } else {
> + usi_ctl &= ~HSI2C_RXCHON;
> + usi_ctl |= HSI2C_TXCHON;
> +
> + i2c_auto_conf &= ~HSI2C_READ_WRITE;
> +
> + usi_int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN;
> + }
> +
> + writel(i2c_addr, i2c->regs + HSI2C_ADDR);
> + writel(usi_ctl, i2c->regs + HSI2C_CTL);
> +
> + i2c_auto_conf |= i2c->msg->len;
> + i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS;
> + writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
> +
> + exynos5_i2c_master_run(i2c);
> +
> + /* Enable appropriate interrupts */
> + writel(usi_int_en, i2c->regs + HSI2C_INT_ENABLE);
> +}
> +
> +static int exynos5_i2c_doxfer(struct exynos5_i2c *i2c, struct i2c_msg *msgs)
> +{
> + unsigned long timeout;
> + int ret;
> +
> + if (i2c->suspended) {
> + dev_err(i2c->dev, "HS-I2C is not initialzed.\n");
> + return -EIO;
> + }
> +
> + if (exynos5_i2c_set_master(i2c)) {
> + dev_err(i2c->dev, "cannot get bus, Master busy.\n");
> + return -EAGAIN;
> + }
> +
> + i2c->msg = msgs;
> + i2c->msg_ptr = 0;
> + i2c->msg_idx = 0;
> +
> + INIT_COMPLETION(i2c->msg_complete);
> +
> + exynos5_i2c_message_start(i2c, msgs);
> +
> + timeout = wait_for_completion_timeout(&i2c->msg_complete,
> + EXYNOS5_I2C_TIMEOUT);
> +
> + ret = i2c->msg_idx;
> +
> + if (timeout == 0)
> + dev_dbg(i2c->dev, "timeout\n");
> + else if ((ret != msgs->len) && (ret < 0))
> + dev_dbg(i2c->dev, "incomplete xfer (%d)\n", i2c->msg_idx);
> +
> + return ret;
> +}
> +
> +static int exynos5_i2c_xfer(struct i2c_adapter *adap,
> + struct i2c_msg *msgs, int num)
> +{
> + struct exynos5_i2c *i2c = (struct exynos5_i2c *)adap->algo_data;
> + int retry, i;
> + int ret;
> +
> + ret = pm_runtime_get_sync(i2c->dev);
> + if (IS_ERR_VALUE(ret))
> + goto out;
> +
> + clk_prepare_enable(i2c->clk);
> +
> + for (retry = 0; retry < adap->retries; retry++) {
> + for (i = 0; i < num; i++) {
> + ret = exynos5_i2c_doxfer(i2c, msgs);
> + msgs++;
> +
> + if (ret == -EAGAIN)
> + break;
> + }
> + if (i == num) {
> + clk_disable_unprepare(i2c->clk);
> +
> + if (i2c->msg_idx == -ENXIO)
> + ret = i2c->msg_idx;
> + else
> + ret = num;
> + goto out;
> + }
> +
> + dev_dbg(i2c->dev, "retrying transfer (%d)\n", retry);
> +
> + udelay(100);
> + }
> +
> + ret = -EREMOTEIO;
> + clk_disable_unprepare(i2c->clk);
> + out:
> + pm_runtime_mark_last_busy(i2c->dev);
> + pm_runtime_put_autosuspend(i2c->dev);
> + return ret;
> +}
> +
> +static u32 exynos5_i2c_func(struct i2c_adapter *adap)
> +{
> + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
> +}
> +
> +static const struct i2c_algorithm exynos5_i2c_algorithm = {
> + .master_xfer = exynos5_i2c_xfer,
> + .functionality = exynos5_i2c_func,
> +};
> +
> +static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c, int speed_mode)
> +{
> + unsigned long i2c_timing_s1;
> + unsigned long i2c_timing_s2;
> + unsigned long i2c_timing_s3;
> + unsigned long i2c_timing_sla;
> + unsigned int op_clk;
> + unsigned int clkin = clk_get_rate(i2c->clk);
> + unsigned int n_clkdiv;
> + unsigned int t_start_su, t_start_hd;
> + unsigned int t_stop_su;
> + unsigned int t_data_su, t_data_hd;
> + unsigned int t_scl_l, t_scl_h;
> + unsigned int t_sr_release;
> + unsigned int t_ftl_cycle;
> + unsigned int i = 0, utemp0 = 0, utemp1 = 0, utemp2 = 0;
> +
> + if (speed_mode == HSI2C_HIGH_SPD)
> + op_clk = HSI2C_HS_TX_CLOCK;
> + else
> + op_clk = HSI2C_FS_TX_CLOCK;
> +
> + /* FPCLK / FI2C =
> + * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
> + * uTemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2)
> + * uTemp1 = (TSCLK_L + TSCLK_H + 2)
> + * uTemp2 = TSCLK_L + TSCLK_H
> + */
> + t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7;
> + utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle;
> +
> + /* CLK_DIV max is 256 */
> + for (i = 0; i < 256; i++) {
> + utemp1 = utemp0 / (i + 1);
> + /* SCLK_L/H max is 255
> + * so sclk_l + sclk_h has max value of 510
> + */
> + if (utemp1 < 511) {
> + utemp2 = utemp1 - 2;
> + break;
> + }
> + }
> +
> + n_clkdiv = i;
> + t_scl_l = utemp2 / 2;
> + t_scl_h = utemp2 / 2;
> + t_start_su = t_scl_l;
> + t_start_hd = t_scl_l;
> + t_stop_su = t_scl_l;
> + t_data_su = t_scl_l / 2;
> + t_data_hd = t_scl_l / 2;
> + t_sr_release = utemp2;
> +
> + i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8;
> + i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
> + i2c_timing_s3 = n_clkdiv << 16 | t_sr_release << 0;
> + i2c_timing_sla = t_data_hd << 0;
> +
> + dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n",
> + t_start_su, t_start_hd, t_stop_su);
> + dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n",
> + t_data_su, t_scl_l, t_scl_h);
> + dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n",
> + n_clkdiv, t_sr_release);
> + dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd);
> +
> + if (speed_mode == HSI2C_HIGH_SPD) {
> + writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1);
> + writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2);
> + writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3);
> + } else {
> + writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1);
> + writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2);
> + writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3);
> + }
> + writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA);
> +
> + return 0;
> +}
> +
> +/**
> + * Parse a list of GPIOs from a node property and request each one
> + *
> + * @param i2c i2c driver data
> + * @return 0 on success, -EINVAL on error, in which case no GPIOs requested
> +*/
> +static int exynos5_i2c_parse_dt_gpio(struct exynos5_i2c *i2c)
> +{
> + int idx, gpio, ret;
> +
> + for (idx = 0; idx < 2; idx++) {
> + gpio = of_get_gpio(i2c->dev->of_node, idx);
> + if (!gpio_is_valid(gpio)) {
> + dev_err(i2c->dev, "invalid gpio[%d]: %d\n", idx, gpio);
> + return -EINVAL;
> + }
> + i2c->gpios[idx] = gpio;
> +
> + ret = devm_gpio_request(i2c->dev, gpio, "i2c-bus");
> + if (ret) {
> + dev_err(i2c->dev, "gpio [%d] request failed\n", gpio);
> + return -EINVAL;
> + }
> + }
> + return 0;
> +}
> +
> +static void exynos5_i2c_init(struct exynos5_i2c *i2c)
> +{
> + unsigned long usi_trailing_ctl = HSI2C_TRAILING_COUNT;
> + unsigned long i2c_conf = HSI2C_AUTO_MODE;
> + unsigned long usi_fifo_ctl;
> +
> + writel(usi_trailing_ctl, i2c->regs + HSI2C_TRAILIG_CTL);
> +
> + /* Set default trigger level for TXFIFO and RXFIFO */
> + usi_fifo_ctl = HSI2C_TXFIFO_TRIGGER_LEVEL | HSI2C_RXFIFO_TRIGGER_LEVEL;
> +
> + /* Enable RXFIFO and TXFIFO */
> + usi_fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN;
> + writel(usi_fifo_ctl, i2c->regs + HSI2C_FIFO_CTL);
> +
> + if (i2c->speed_mode == HSI2C_HIGH_SPD) {
> + exynos5_i2c_set_timing(i2c, HSI2C_HIGH_SPD);
> + /* Configure I2C controller in High speed mode */
> + i2c_conf |= HSI2C_HS_MODE;
> + writel(i2c_conf, i2c->regs + HSI2C_CONF);
> + } else {
> + /* Configure I2C controller in Fast speed mode */
> + exynos5_i2c_set_timing(i2c, HSI2C_FAST_SPD);
> + }
> +}
> +
> +#define HSI2C_REG(regname) {.name = #regname, .offset = regname}
> +static struct debugfs_reg32 exynos5_hsi2c_regs[] = {
> + HSI2C_REG(HSI2C_CTL), HSI2C_REG(HSI2C_FIFO_CTL),
> + HSI2C_REG(HSI2C_TRAILIG_CTL), HSI2C_REG(HSI2C_CLK_CTL),
> + HSI2C_REG(HSI2C_CLK_SLOT), HSI2C_REG(HSI2C_INT_ENABLE),
> + HSI2C_REG(HSI2C_INT_STATUS), HSI2C_REG(HSI2C_ERR_STATUS),
> + HSI2C_REG(HSI2C_FIFO_STATUS), HSI2C_REG(HSI2C_TX_DATA),
> + HSI2C_REG(HSI2C_RX_DATA), HSI2C_REG(HSI2C_CONF),
> + HSI2C_REG(HSI2C_AUTO_CONF), HSI2C_REG(HSI2C_TIMEOUT),
> + HSI2C_REG(HSI2C_MANUAL_CMD), HSI2C_REG(HSI2C_TRANS_STATUS),
> + HSI2C_REG(HSI2C_TIMING_HS1), HSI2C_REG(HSI2C_TIMING_HS2),
> + HSI2C_REG(HSI2C_TIMING_HS3), HSI2C_REG(HSI2C_TIMING_FS1),
> + HSI2C_REG(HSI2C_TIMING_FS2), HSI2C_REG(HSI2C_TIMING_FS3),
> + HSI2C_REG(HSI2C_TIMING_SLA), HSI2C_REG(HSI2C_ADDR),
> +};
> +
> +static struct debugfs_regset32 exynos5_hsi2c_regset = {
> + .regs = exynos5_hsi2c_regs,
> + .nregs = ARRAY_SIZE(exynos5_hsi2c_regs),
> +};
> +
> +static struct dentry *exynos5_hsi2c_reg_debugfs;
> +
> +static int exynos5_i2c_probe(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct exynos5_i2c *i2c;
> + int ret;
> +
> + if (!np) {
> + dev_err(&pdev->dev, "no device node\n");
> + return -ENOENT;
> + }
> +
> + i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL);
> + if (!i2c) {
> + dev_err(&pdev->dev, "no memory for state\n");
> + return -ENOMEM;
> + }
> +
> + i2c->bus_num = -1;
> + /* Mode of operation High/Fast Speed mode */
> + of_property_read_u32(np, "samsung,hs-mode", &i2c->speed_mode);
> +
> + strlcpy(i2c->adap.name, "exynos5-hsi2c", sizeof(i2c->adap.name));
> + i2c->adap.owner = THIS_MODULE;
> + i2c->adap.algo = &exynos5_i2c_algorithm;
> + i2c->adap.retries = 2;
> + i2c->adap.class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
> +
> + i2c->dev = &pdev->dev;
> + i2c->clk = clk_get(&pdev->dev, "hsi2c");
> + if (IS_ERR(i2c->clk)) {
> + dev_err(&pdev->dev, "cannot get clock\n");
> + ret = -ENOENT;
> + goto err_noclk;
> + }
> +
> + dev_dbg(&pdev->dev, "clock source %p\n", i2c->clk);
> +
> + clk_prepare_enable(i2c->clk);
> +
> + i2c->regs = of_iomap(np, 0);
> + if (!i2c->regs) {
> + dev_err(&pdev->dev, "cannot map HS-I2C IO\n");
> + ret = -ENXIO;
> + goto err_clk;
> + }
> +
> + /* inititalise the gpio */
> + if (exynos5_i2c_parse_dt_gpio(i2c))
> + return -EINVAL;
> +
> + i2c->irq = irq_of_parse_and_map(np, 0);
> + if (i2c->irq) {
> + ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq,
> + 0, dev_name(&pdev->dev), i2c);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n",
> + i2c->irq);
> + goto err_iomap;
> + }
> + }
> +
> + /*
> + * TODO: Use private lock to avoid race conditions as
> + * mentioned in pm_runtime.txt
> + */
> + pm_runtime_enable(i2c->dev);
> + pm_runtime_set_autosuspend_delay(i2c->dev, EXYNOS5_I2C_PM_TIMEOUT);
> + pm_runtime_use_autosuspend(i2c->dev);
> +
> + ret = pm_runtime_get_sync(i2c->dev);
> + if (IS_ERR_VALUE(ret))
> + goto err_iomap;
> +
> + exynos5_i2c_init(i2c);
> +
> + i2c->adap.algo_data = i2c;
> + i2c->adap.dev.parent = &pdev->dev;
> + i2c->adap.nr = i2c->bus_num;
> + i2c->adap.dev.of_node = pdev->dev.of_node;
> +
> + ret = i2c_add_numbered_adapter(&i2c->adap);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "failed to add bus to i2c core\n");
> + goto err_pm;
> + }
> +
> + init_completion(&i2c->msg_complete);
> + of_i2c_register_devices(&i2c->adap);
> + platform_set_drvdata(pdev, i2c);
> +
> + dev_info(&pdev->dev, "%s: Exynos5 HS-I2C adapter\n",
> + dev_name(&i2c->adap.dev));
> +
> + exynos5_hsi2c_reg_debugfs = debugfs_create_regset32("exynos5-hsi2c",
> + S_IFREG | S_IRUGO,
> + NULL, &exynos5_hsi2c_regset);
I took the reference of this call from MFD driver, which is the only
driver using this (i guess)
usb/dwc3.c driver had a generic implementation. I wasn't sure of the
implementation.
if someone can help, i willing to do that.
> + clk_disable_unprepare(i2c->clk);
> + pm_runtime_mark_last_busy(i2c->dev);
> + pm_runtime_put_autosuspend(i2c->dev);
> + return 0;
> +
> + err_pm:
> + pm_runtime_put(i2c->dev);
> + pm_runtime_disable(&pdev->dev);
> + err_iomap:
> + iounmap(i2c->regs);
> + err_clk:
> + clk_disable_unprepare(i2c->clk);
> + err_noclk:
> + return ret;
> +}
> +
> +static int exynos5_i2c_remove(struct platform_device *pdev)
> +{
> + struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
> + int ret;
> +
> + ret = pm_runtime_get_sync(&pdev->dev);
> + if (IS_ERR_VALUE(ret))
> + return ret;
> +
> + clk_disable_unprepare(i2c->clk);
> + pm_runtime_put(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
> +
> + i2c_del_adapter(&i2c->adap);
> +
> + iounmap(i2c->regs);
> + platform_set_drvdata(pdev, NULL);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +static int exynos5_i2c_suspend_noirq(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
> +
> + i2c->suspended = 1;
> +
> + return 0;
> +}
> +
> +static int exynos5_i2c_resume_noirq(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
> +
> + clk_prepare_enable(i2c->clk);
> + exynos5_i2c_init(i2c);
> + clk_disable_unprepare(i2c->clk);
> + i2c->suspended = 0;
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = {
> + .suspend_noirq = exynos5_i2c_suspend_noirq,
> + .resume_noirq = exynos5_i2c_resume_noirq,
> +};
> +
> +#define EXYNOS5_DEV_PM_OPS (&exynos5_i2c_dev_pm_ops)
> +#else
> +#define EXYNOS5_DEV_PM_OPS NULL
> +#endif
> +
> +static struct platform_driver exynos5_i2c_driver = {
> + .probe = exynos5_i2c_probe,
> + .remove = exynos5_i2c_remove,
> + .driver = {
> + .owner = THIS_MODULE,
> + .name = "exynos5-hsi2c",
> + .pm = EXYNOS5_DEV_PM_OPS,
> + .of_match_table = exynos5_i2c_match,
> + },
> +};
> +
> +static int __init i2c_adap_exynos5_init(void)
> +{
> + return platform_driver_register(&exynos5_i2c_driver);
> +}
> +subsys_initcall(i2c_adap_exynos5_init);
> +
> +static void __exit i2c_adap_exynos5_exit(void)
> +{
> + platform_driver_unregister(&exynos5_i2c_driver);
> +}
> +module_exit(i2c_adap_exynos5_exit);
> +
> +MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver");
> +MODULE_AUTHOR("Naveen Krishna Chatradhi, <ch.naveen@...sung.com>");
> +MODULE_AUTHOR("Taekgyun Ko, <taeggyun.ko@...sung.com>");
> +MODULE_LICENSE("GPL");
> --
> 1.7.9.5
>
--
Shine bright,
(: Nav :)
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists