| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1359109440-2195-2-git-send-email-kishon@ti.com>
Date: Fri, 25 Jan 2013 15:53:57 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: <rob.herring@...xeda.com>, <rob@...dley.net>, <tony@...mide.com>,
<balbi@...com>, <b-cousson@...com>, <linux-usb@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-omap@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-doc@...r.kernel.org>, <devicetree-discuss@...ts.ozlabs.org>
CC: <grant.likely@...retlab.ca>, <linux@....linux.org.uk>,
<gregkh@...uxfoundation.org>, <kishon@...com>
Subject: [PATCH v4 1/4] drivers: usb: phy: add a new driver for usb part of control module
Added a new driver for the usb part of control module. This has an API
to power on the USB2 phy and an API to write to the mailbox depending on
whether MUSB has to act in host mode or in device mode.
Writing to control module registers for doing the above task which was
previously done in omap glue and in omap-usb2 phy will be removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@...com>
---
Documentation/devicetree/bindings/usb/omap-usb.txt | 30 +-
Documentation/devicetree/bindings/usb/usb-phy.txt | 5 +
drivers/usb/phy/Kconfig | 10 +
drivers/usb/phy/Makefile | 1 +
drivers/usb/phy/omap-control-usb.c | 295 ++++++++++++++++++++
include/linux/usb/omap_control_usb.h | 92 ++++++
6 files changed, 432 insertions(+), 1 deletion(-)
create mode 100644 drivers/usb/phy/omap-control-usb.c
create mode 100644 include/linux/usb/omap_control_usb.h
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 29a043e..2d8c6c4 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -1,4 +1,4 @@
-OMAP GLUE
+OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
OMAP MUSB GLUE
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
@@ -16,6 +16,10 @@ OMAP MUSB GLUE
- power : Should be "50". This signifies the controller can supply upto
100mA when operating in host mode.
+Optional properties:
+ - ctrl-module : phandle of the control module this glue uses to write to
+ mailbox
+
SOC specific device node entry
usb_otg_hs: usb_otg_hs@...ab000 {
compatible = "ti,omap4-musb";
@@ -23,6 +27,7 @@ usb_otg_hs: usb_otg_hs@...ab000 {
multipoint = <1>;
num_eps = <16>;
ram_bits = <12>;
+ ctrl-module = <&omap_control_usb>;
};
Board specific device node entry
@@ -31,3 +36,26 @@ Board specific device node entry
mode = <3>;
power = <50>;
};
+
+OMAP CONTROL USB
+
+Required properties:
+ - compatible: Should be "ti,omap-control-usb"
+ - reg : Address and length of the register set for the device. It contains
+ the address of "control_dev_conf" and "otghs_control" or "phy_power_usb"
+ depending upon omap4 or omap5.
+ - reg-names: The names of the register addresses corresponding to the registers
+ filled in "reg".
+ - ti,type: This is used to differentiate whether the control module has
+ usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to
+ notify events to the musb core and omap5 has usb3 phy power register to
+ power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3
+ phy power.
+
+omap_control_usb: omap-control-usb@...02300 {
+ compatible = "ti,omap-control-usb";
+ reg = <0x4a002300 0x4>,
+ <0x4a00233c 0x4>;
+ reg-names = "control_dev_conf", "otghs_control";
+ ti,type = <1>;
+};
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
index 80d4148..2466b6f 100644
--- a/Documentation/devicetree/bindings/usb/usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -8,10 +8,15 @@ Required properties:
add the address of control module dev conf register until a driver for
control module is added
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+ the PHY.
+
This is usually a subnode of ocp2scp to which it is connected.
usb2phy@...ad080 {
compatible = "ti,omap-usb2";
reg = <0x4a0ad080 0x58>,
<0x4a002300 0x4>;
+ ctrl-module = <&omap_control_usb>;
};
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 36a85b6..65b6a80 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -14,6 +14,16 @@ config OMAP_USB2
The USB OTG controller communicates with the comparator using this
driver.
+config OMAP_CONTROL_USB
+ tristate "OMAP CONTROL USB Driver"
+ depends on ARCH_OMAP2PLUS
+ help
+ Enable this to add support for the USB part present in the control
+ module. This driver has API to power on the USB2 PHY and to write to
+ the mailbox. The mailbox is present only in omap4 and the register to
+ power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
+ additional register to power on USB3 PHY.
+
config USB_ISP1301
tristate "NXP ISP1301 USB transceiver support"
depends on USB || USB_GADGET
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index ec304f6..ee97767 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -5,6 +5,7 @@
ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG
obj-$(CONFIG_OMAP_USB2) += omap-usb2.o
+obj-$(CONFIG_OMAP_CONTROL_USB) += omap-control-usb.o
obj-$(CONFIG_USB_ISP1301) += isp1301.o
obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o
obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o
diff --git a/drivers/usb/phy/omap-control-usb.c b/drivers/usb/phy/omap-control-usb.c
new file mode 100644
index 0000000..e9b529f
--- /dev/null
+++ b/drivers/usb/phy/omap-control-usb.c
@@ -0,0 +1,295 @@
+/*
+ * omap-control-usb.c - The USB part of control module.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@...com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/usb/omap_control_usb.h>
+
+static struct omap_control_usb *control_usb;
+
+/**
+ * omap_get_control_dev - returns the device pointer for this control device
+ *
+ * This API should be called to get the device pointer for this control
+ * module device. This device pointer should be used for called other
+ * exported API's in this driver.
+ *
+ * To be used by PHY driver and glue driver.
+ */
+struct device *omap_get_control_dev(void)
+{
+ if (!control_usb)
+ return ERR_PTR(-ENODEV);
+
+ return control_usb->dev;
+}
+EXPORT_SYMBOL_GPL(omap_get_control_dev);
+
+/**
+ * omap_control_usb3_phy_power - power on/off the serializer using control
+ * module
+ * @dev: the control module device
+ * @on: 0 to off and 1 to on based on powering on or off the PHY
+ *
+ * usb3 PHY driver should call this API to power on or off the PHY.
+ */
+void omap_control_usb3_phy_power(struct device *dev, bool on)
+{
+ u32 val;
+ unsigned long rate;
+ struct omap_control_usb *control_usb = dev_get_drvdata(dev);
+
+ if (control_usb->type != OMAP_CTRL_DEV_TYPE2)
+ return;
+
+ rate = clk_get_rate(control_usb->sys_clk);
+ rate = rate/1000000;
+
+ val = readl(control_usb->phy_power);
+
+ if (on) {
+ val &= ~(OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK |
+ OMAP_CTRL_USB_PWRCTL_CLK_FREQ_MASK);
+ val |= OMAP_CTRL_USB3_PHY_TX_RX_POWERON <<
+ OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
+ val |= rate << OMAP_CTRL_USB_PWRCTL_CLK_FREQ_SHIFT;
+ } else {
+ val &= ~OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK;
+ val |= OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF <<
+ OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
+ }
+
+ writel(val, control_usb->phy_power);
+}
+EXPORT_SYMBOL_GPL(omap_control_usb3_phy_power);
+
+/**
+ * omap_control_usb_phy_power - power on/off the phy using control module reg
+ * @dev: the control module device
+ * @on: 0 or 1, based on powering on or off the PHY
+ */
+void omap_control_usb_phy_power(struct device *dev, int on)
+{
+ u32 val;
+ struct omap_control_usb *control_usb = dev_get_drvdata(dev);
+
+ val = readl(control_usb->dev_conf);
+
+ if (on)
+ val &= ~OMAP_CTRL_DEV_PHY_PD;
+ else
+ val |= OMAP_CTRL_DEV_PHY_PD;
+
+ writel(val, control_usb->dev_conf);
+}
+EXPORT_SYMBOL_GPL(omap_control_usb_phy_power);
+
+/**
+ * omap_control_usb_host_mode - set AVALID, VBUSVALID and ID pin in grounded
+ * @ctrl_usb: struct omap_control_usb *
+ *
+ * Writes to the mailbox register to notify the usb core that a usb
+ * device has been connected.
+ */
+static void omap_control_usb_host_mode(struct omap_control_usb *ctrl_usb)
+{
+ u32 val;
+
+ val = readl(ctrl_usb->otghs_control);
+ val &= ~(OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND);
+ val |= OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID;
+ writel(val, ctrl_usb->otghs_control);
+}
+
+/**
+ * omap_control_usb_device_mode - set AVALID, VBUSVALID and ID pin in high
+ * impedance
+ * @ctrl_usb: struct omap_control_usb *
+ *
+ * Writes to the mailbox register to notify the usb core that it has been
+ * connected to a usb host.
+ */
+static void omap_control_usb_device_mode(struct omap_control_usb *ctrl_usb)
+{
+ u32 val;
+
+ val = readl(ctrl_usb->otghs_control);
+ val &= ~OMAP_CTRL_DEV_SESSEND;
+ val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_AVALID |
+ OMAP_CTRL_DEV_VBUSVALID;
+ writel(val, ctrl_usb->otghs_control);
+}
+
+/**
+ * omap_control_usb_set_sessionend - Enable SESSIONEND and IDIG to high
+ * impedance
+ * @ctrl_usb: struct omap_control_usb *
+ *
+ * Writes to the mailbox register to notify the usb core it's now in
+ * disconnected state.
+ */
+static void omap_control_usb_set_sessionend(struct omap_control_usb *ctrl_usb)
+{
+ u32 val;
+
+ val = readl(ctrl_usb->otghs_control);
+ val &= ~(OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID);
+ val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND;
+ writel(val, ctrl_usb->otghs_control);
+}
+
+/**
+ * omap_control_usb_set_mode - Calls to functions to set USB in one of host mode
+ * or device mode or to denote disconnected state
+ * @dev: the control module device
+ * @mode: The mode to which usb should be configured
+ *
+ * This is an API to write to the mailbox register to notify the usb core that
+ * a usb device has been connected.
+ */
+void omap_control_usb_set_mode(struct device *dev,
+ enum omap_control_usb_mode mode)
+{
+ struct omap_control_usb *ctrl_usb;
+
+ if (IS_ERR(dev) || control_usb->type != OMAP_CTRL_DEV_TYPE1)
+ return;
+
+ ctrl_usb = dev_get_drvdata(dev);
+
+ switch (mode) {
+ case USB_MODE_HOST:
+ omap_control_usb_host_mode(ctrl_usb);
+ break;
+ case USB_MODE_DEVICE:
+ omap_control_usb_device_mode(ctrl_usb);
+ break;
+ case USB_MODE_DISCONNECT:
+ omap_control_usb_set_sessionend(ctrl_usb);
+ break;
+ default:
+ dev_vdbg(dev, "invalid omap control usb mode\n");
+ }
+}
+EXPORT_SYMBOL_GPL(omap_control_usb_set_mode);
+
+static int omap_control_usb_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ struct device_node *np = pdev->dev.of_node;
+ struct omap_control_usb_platform_data *pdata = pdev->dev.platform_data;
+
+ control_usb = devm_kzalloc(&pdev->dev, sizeof(*control_usb),
+ GFP_KERNEL);
+ if (!control_usb) {
+ dev_err(&pdev->dev, "unable to alloc memory for control usb\n");
+ return -ENOMEM;
+ }
+
+ if (np) {
+ of_property_read_u32(np, "ti,type", &control_usb->type);
+ } else if (pdata) {
+ control_usb->type = pdata->type;
+ } else {
+ dev_err(&pdev->dev, "no pdata present\n");
+ return -EINVAL;
+ }
+
+ control_usb->dev = &pdev->dev;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "control_dev_conf");
+ control_usb->dev_conf = devm_request_and_ioremap(&pdev->dev, res);
+ if (!control_usb->dev_conf) {
+ dev_err(&pdev->dev, "Failed to obtain io memory\n");
+ return -EADDRNOTAVAIL;
+ }
+
+ if (control_usb->type == OMAP_CTRL_DEV_TYPE1) {
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "otghs_control");
+ control_usb->otghs_control = devm_request_and_ioremap(
+ &pdev->dev, res);
+ if (!control_usb->otghs_control) {
+ dev_err(&pdev->dev, "Failed to obtain io memory\n");
+ return -EADDRNOTAVAIL;
+ }
+ }
+
+ if (control_usb->type == OMAP_CTRL_DEV_TYPE2) {
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "phy_power_usb");
+ control_usb->phy_power = devm_request_and_ioremap(
+ &pdev->dev, res);
+ if (!control_usb->phy_power) {
+ dev_dbg(&pdev->dev, "Failed to obtain io memory\n");
+ return -EADDRNOTAVAIL;
+ }
+
+ control_usb->sys_clk = devm_clk_get(control_usb->dev,
+ "sys_clkin");
+ if (IS_ERR(control_usb->sys_clk)) {
+ pr_err("%s: unable to get sys_clkin\n", __func__);
+ return -EINVAL;
+ }
+ }
+
+
+ dev_set_drvdata(control_usb->dev, control_usb);
+
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id omap_control_usb_id_table[] = {
+ { .compatible = "ti,omap-control-usb" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, omap_control_usb_id_table);
+#endif
+
+static struct platform_driver omap_control_usb_driver = {
+ .probe = omap_control_usb_probe,
+ .driver = {
+ .name = "omap-control-usb",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(omap_control_usb_id_table),
+ },
+};
+
+static int __init omap_control_usb_init(void)
+{
+ return platform_driver_register(&omap_control_usb_driver);
+}
+subsys_initcall(omap_control_usb_init);
+
+static void __exit omap_control_usb_exit(void)
+{
+ platform_driver_unregister(&omap_control_usb_driver);
+}
+module_exit(omap_control_usb_exit);
+
+MODULE_ALIAS("platform: omap_control_usb");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP Control Module USB Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/usb/omap_control_usb.h b/include/linux/usb/omap_control_usb.h
new file mode 100644
index 0000000..84c90aa
--- /dev/null
+++ b/include/linux/usb/omap_control_usb.h
@@ -0,0 +1,92 @@
+/*
+ * omap_control_usb.h - Header file for the USB part of control module.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@...com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __OMAP_CONTROL_USB_H__
+#define __OMAP_CONTROL_USB_H__
+
+struct omap_control_usb {
+ struct device *dev;
+
+ u32 __iomem *dev_conf;
+ u32 __iomem *otghs_control;
+ u32 __iomem *phy_power;
+
+ struct clk *sys_clk;
+
+ u32 type;
+};
+
+struct omap_control_usb_platform_data {
+ u8 type;
+};
+
+enum omap_control_usb_mode {
+ USB_MODE_UNDEFINED = 0,
+ USB_MODE_HOST,
+ USB_MODE_DEVICE,
+ USB_MODE_DISCONNECT,
+};
+
+/* To differentiate ctrl module IP having either mailbox or USB3 PHY power */
+#define OMAP_CTRL_DEV_TYPE1 0x1
+#define OMAP_CTRL_DEV_TYPE2 0x2
+
+#define OMAP_CTRL_DEV_PHY_PD BIT(0)
+
+#define OMAP_CTRL_DEV_AVALID BIT(0)
+#define OMAP_CTRL_DEV_BVALID BIT(1)
+#define OMAP_CTRL_DEV_VBUSVALID BIT(2)
+#define OMAP_CTRL_DEV_SESSEND BIT(3)
+#define OMAP_CTRL_DEV_IDDIG BIT(4)
+
+#define OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK 0x003FC000
+#define OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT 0xE
+
+#define OMAP_CTRL_USB_PWRCTL_CLK_FREQ_MASK 0xFFC00000
+#define OMAP_CTRL_USB_PWRCTL_CLK_FREQ_SHIFT 0x16
+
+#define OMAP_CTRL_USB3_PHY_TX_RX_POWERON 0x3
+#define OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF 0x0
+
+#if IS_ENABLED(CONFIG_OMAP_CONTROL_USB)
+extern struct device *omap_get_control_dev(void);
+extern void omap_control_usb_phy_power(struct device *dev, int on);
+extern void omap_control_usb3_phy_power(struct device *dev, bool on);
+extern void omap_control_usb_set_mode(struct device *dev,
+ enum omap_control_usb_mode mode);
+#else
+static inline struct device *omap_get_control_dev()
+{
+ return ERR_PTR(-ENODEV);
+}
+
+static inline void omap_control_usb_phy_power(struct device *dev, int on)
+{
+}
+
+static inline void omap_control_usb3_phy_power(struct device *dev, int on)
+{
+}
+
+static inline void omap_control_usb_set_mode(struct device *dev,
+ enum omap_control_usb_mode mode)
+{
+}
+#endif
+
+#endif /* __OMAP_CONTROL_USB_H__ */
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists