| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5155DA7D.2080005@fold.natur.cuni.cz>
Date: Fri, 29 Mar 2013 19:16:29 +0100
From: Martin Mokrejs <mmokrejs@...d.natur.cuni.cz>
To: Sarah Sharp <sarah.a.sharp@...ux.intel.com>
CC: "Rafael J. Wysocki" <rjw@...k.pl>,
Bjorn Helgaas <bhelgaas@...gle.com>,
ACPI Devel Maling List <linux-acpi@...r.kernel.org>,
LKML <linux-kernel@...r.kernel.org>,
Linux PM list <linux-pm@...r.kernel.org>,
Len Brown <lenb@...nel.org>,
Matthew Garrett <mjg59@...f.ucam.org>,
"Accardi, Kristen C" <kristen.c.accardi@...el.com>,
"Huang, Ying" <ying.huang@...el.com>, linux-pci@...r.kernel.org
Subject: Re: [Update][PATCH] PCI / ACPI: Always resume devices on ACPI wakeup
notifications
So, I re-tested again with the patch and 3.8.3 but without laptop-mode-tools.
The xHCI port works fine provided /sys/bus/pci/devices/0000:0b:00.0/power/control
is set to on and /sys/bus/pci/devices/0000:00:1c.4/power/control also to on.
If I set parent 1c.4 to auto, it gets suspended and the port seems dead until
a device is in and I wake it using lsusb -vv. There must be a bug in linux so
that it cannot overcome upstream 1c.4 sleeping while willing to access 0b:00.
Or more likely, that upstream root port should be prevented to fall asleep, right?
# lspci -tv
-[0000:00]-+-00.0 Intel Corporation 2nd Generation Core Processor Family DRAM Controller
+-02.0 Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller
+-16.0 Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1
+-1a.0 Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2
+-1b.0 Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller
+-1c.0-[03-04]--
+-1c.1-[05-06]----00.0 Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller
+-1c.3-[09-0a]----00.0 Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak]
+-1c.4-[0b-0c]----00.0 Texas Instruments TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller
+-1c.7-[11-16]----00.0 Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
+-1d.0 Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1
+-1f.0 Intel Corporation HM67 Express Chipset Family LPC Controller
+-1f.2 Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller
\-1f.3 Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller
#
I have attached the lspci -vvv -n.
Interestingly, maybe, the TI xHCI controller ended up after my tests
changed. I booted up with all devices with power/control set to on
due to laptop-mode-tools uninstalled. I fiddled with the echo commands
tweaking 1c.4 and 0b:00 but in the end set both back to "on". However,
below is some diff. Don't know what that means. Maybe because I tried
to write '0', 'off', 'none' to the control file? ;-)
00:1c.4 0604: 8086:1c18 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0c, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f7d00000-f7dfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
- RootSta: PME ReqID 0000, PMEStatus- PMEPending-
+ RootSta: PME ReqID 0b00, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: 1028:04b3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
0b:00.0 0c03: 104c:8241 (rev 02) (prog-if 30 [XHCI])
Subsystem: 1028:04b3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at f7d10000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [c0] MSI-X: Enable+ Count=8 Masked-
Vector table: BAR=2 offset=00000000
PBA: BAR=2 offset=00001000
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
+ CESta: RxErr- BadTLP- BadDLLP+ Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Device Serial Number 08-00-28-00-00-20-00-00
Kernel driver in use: xhci_hcd
View attachment "lspci_vvvn_initial.txt" of type "text/plain" (31820 bytes)
Powered by blists - more mailing lists