| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <35286B1AE75A7C47BFF0870081A31B4B45A5A0B7DA@SAFEX1MAIL4.st.com>
Date: Fri, 19 Apr 2013 18:06:04 +0200
From: Mathias LEBLANC <Mathias.LEBLANC@...com>
To: Kent Yoder <shpedoikal@...il.com>
Cc: Kent Yoder <key@...ux.vnet.ibm.com>,
Rajiv Andrade <mail@...jiv.net>,
Marcel Selhorst <tpmdd@...horst.net>,
Sirrix AG <tpmdd@...rix.com>,
"tpmdd-devel@...ts.sourceforge.net"
<tpmdd-devel@...ts.sourceforge.net>,
Jean-Luc BLANC <jean-luc.blanc@...com>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>
Subject: RE: [tpmdd-devel] [PATCH 1/1] TPM: STMicroelectronics st33 driver
SPI
Hi Kent,
> + /* u8 LOC+DIR u8 ADD u16 LENGHT u8* data */
> + /* u8 LATENCY u8 LATENCY */
Kent: What do these comments mean?
Mathias: These comments describe the I2C command protocol.
Regarding the return value of these W/R functions, it's an error of comment, these functions return 0 on success else a negative error code.
Thanks,
Mathias Leblanc
-----Original Message-----
From: Kent Yoder [mailto:shpedoikal@...il.com]
Sent: 17 April, 2013 23:32
To: Mathias LEBLANC
Cc: Kent Yoder; Rajiv Andrade; Marcel Selhorst; Sirrix AG; tpmdd-devel@...ts.sourceforge.net; Jean-Luc BLANC; linux-kernel@...r.kernel.org
Subject: Re: [tpmdd-devel] [PATCH 1/1] TPM: STMicroelectronics st33 driver SPI
Hi Matthias,
On Fri, Apr 12, 2013 at 10:44:11AM +0200, Matthias Leblanc wrote:
> From: Mathias Leblanc <mathias.leblanc@...com>
>
> * STMicroelectronics version 1.2.0, Copyright (C) 2010
> * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> * This is free software, and you are welcome to redistribute it
> * under certain conditions.
>
> This is the driver for TPM chip from ST Microelectronics.
>
> If you have a TPM security chip from STMicroelectronics working with
> an SPI, in menuconfig or .config choose the tpm driver on device -->
> tpm and activate the protocol of your choice before compiling the
> kernel.
> The driver will be accessible from within Linux.
>
> Tested on linux x86/x64 and beagleboard REV B & XM REV C
>
> Signed-off-by: Mathias Leblanc <mathias.leblanc@...com>
> ---
> drivers/char/tpm/Kconfig | 10 +
> drivers/char/tpm/Makefile | 1 +
> drivers/char/tpm/tpm_spi_stm_st33.c | 1116 ++++++++++++++++++++++++++++++++++
> drivers/char/tpm/tpm_spi_stm_st33.h | 75 +++
> include/linux/spi/tpm_spi_stm_st33.h | 44 ++
> 7 files changed, 1246 insertions(+), 161 deletions(-) delete mode
> 100644 .gitignore delete mode 100644 REPORTING-BUGS create mode
> 100644 drivers/char/tpm/tpm_spi_stm_st33.c
> create mode 100644 drivers/char/tpm/tpm_spi_stm_st33.h
> create mode 100644 include/linux/spi/tpm_spi_stm_st33.h
>
> diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig index
> dbfd564..2fc1254 100644
> --- a/drivers/char/tpm/Kconfig
> +++ b/drivers/char/tpm/Kconfig
> @@ -91,4 +91,14 @@ config TCG_ST33_I2C
> To compile this driver as a module, choose M here; the module will be
> called tpm_stm_st33_i2c.
>
> +config TCG_ST33_SPI
> + tristate "STMicroelectronics ST33 SPI"
> + depends on SPI
> + depends on GPIOLIB
> + ---help---
> + If you have a TPM security chip from STMicroelectronics working with
> + an SPI bus say Yes and it will be accessible from within Linux.
> + To compile this driver as a module, choose M here; the module will be
> + called tpm_stm_st33_spi.
> +
> endif # TCG_TPM
> diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile
> index a3736c9..a1db3dd 100644
> --- a/drivers/char/tpm/Makefile
> +++ b/drivers/char/tpm/Makefile
> @@ -18,3 +18,4 @@ obj-$(CONFIG_TCG_ATMEL) += tpm_atmel.o
> obj-$(CONFIG_TCG_INFINEON) += tpm_infineon.o
> obj-$(CONFIG_TCG_IBMVTPM) += tpm_ibmvtpm.o
> obj-$(CONFIG_TCG_ST33_I2C) += tpm_i2c_stm_st33.o
> +obj-$(CONFIG_TCG_ST33_SPI) += tpm_spi_stm_st33.o
> diff --git a/drivers/char/tpm/tpm_spi_stm_st33.c
> b/drivers/char/tpm/tpm_spi_stm_st33.c
> new file mode 100644
> index 0000000..9462f7c
> --- /dev/null
> +++ b/drivers/char/tpm/tpm_spi_stm_st33.c
> @@ -0,0 +1,1116 @@
> +/*
> + * STMicroelectronics TPM SPI Linux driver for TPM ST33ZP24
> + * Copyright (C) 2009, 2010 STMicroelectronics
> + *
> + * This program is free software; you can redistribute it and/or
> +modify
> + * it under the terms of the GNU General Public License as published
> +by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> +along
> + * with this program; if not, write to the Free Software Foundation,
> +Inc.,
> + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> + *
> + * STMicroelectronics version 1.2.0, Copyright (C) 2010
> + * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> + * This is free software, and you are welcome to redistribute it
> + * under certain conditions.
> + *
> + * @Author: Christophe RICARD tpmsupport@...com
> + *
> + * @File: tpm_stm_st33_spi.c
> + *
> + * @Synopsis:
> + * 09/15/2010: First shot driver tpm_tis driver for lpc is
> + * used as model.
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
This looks unused, please remove.
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/delay.h>
> +#include <linux/init.h>
> +#include <linux/spi/spi.h>
> +#include <linux/wait.h>
> +#include <linux/string.h>
> +#include <linux/interrupt.h>
> +#include <linux/spinlock.h>
> +#include <linux/sysfs.h>
> +#include <linux/gpio.h>
> +#include <linux/sched.h>
> +#include <linux/uaccess.h>
> +#include <linux/io.h>
> +#include <linux/slab.h>
> +#include <linux/sched.h>
> +
> +#include <linux/spi/tpm_spi_stm_st33.h>
Is there a need for this header to live in linux/spi? You should move it into the local header.
> +#include "tpm.h"
> +
> +#include "tpm_spi_stm_st33.h"
> +
> +#ifdef DEBUG
> +#define FUNC_ENTER() pr_info("%s\n", __func__)
> +#else
> +#define FUNC_ENTER() do {} while (0)
> +#endif
Please remove FUNC_ENTER().
> +enum stm33zp24_access {
> + TPM_ACCESS_VALID = 0x80,
> + TPM_ACCESS_ACTIVE_LOCALITY = 0x20,
> + TPM_ACCESS_REQUEST_PENDING = 0x04,
> + TPM_ACCESS_REQUEST_USE = 0x02,
> +};
> +
> +enum stm33zp24_status {
> + TPM_STS_VALID = 0x80,
> + TPM_STS_COMMAND_READY = 0x40,
> + TPM_STS_GO = 0x20,
> + TPM_STS_DATA_AVAIL = 0x10,
> + TPM_STS_DATA_EXPECT = 0x08,
> +};
> +
> +enum stm33zp24_int_flags {
> + TPM_GLOBAL_INT_ENABLE = 0x80,
> + TPM_INTF_CMD_READY_INT = 0x080,
> + TPM_INTF_FIFO_AVALAIBLE_INT = 0x040,
> + TPM_INTF_WAKE_UP_READY_INT = 0x020,
> + TPM_INTF_LOC4SOFTRELEASE_INT = 0x008,
> + TPM_INTF_LOCALITY_CHANGE_INT = 0x004,
> + TPM_INTF_STS_VALID_INT = 0x002,
> + TPM_INTF_DATA_AVAIL_INT = 0x001,
> +};
> +
> +enum tis_defaults {
> + TIS_SHORT_TIMEOUT = 750, /* ms */
> + TIS_LONG_TIMEOUT = 2000, /* 2 sec */
> +};
> +
> +/*
> + * write8_reg
> + * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be written
> + * @param: tpm_data, the tpm_data to write inside the tpm_register
> + * @param: tpm_size, The length of the data
> + * @return: number of byte written successfully: should be one if success.
> + */
> +static int write8_reg(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
> +{
> + /* u8 LOC+DIR u8 ADD u16 LENGHT u8* data */
> + /* u8 LATENCY u8 LATENCY */
What do these comments mean?
> +
> + u8 data;
> + int i = 0, j;
> + int value = 0;
> + struct spi_device *dev = (struct spi_device *)tpm->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + u8 *data_buffer = platform_data->tpm_spi_buffer[0];
> + struct spi_transfer xfer = {
> + .tx_buf = data_buffer,
> + .rx_buf = platform_data->tpm_spi_buffer[1],
> + };
> + struct spi_message msg;
> + u8 latency = platform_data->latency + tpm_size + 1;
> +
> +
> + FUNC_ENTER();
> + /* Pre-Header */
> +
> + data = TPM_WRITE_DIRECTION | tpm->vendor.locality;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_register;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> +
> + if (
> + tpm_size > 0 &&
> + (tpm_register == TPM_DATA_FIFO ||
> + tpm_register == TPM_HASH_DATA)) {
Well that looks weird. This is more readable:
if (tpm_size > 0 &&
(tpm_register == TPM_DATA_FIFO ||
tpm_register == TPM_HASH_DATA)) {
But probably more relevant is that write8_reg is never called with tpm_register == TPM_HASH_DATA. Can you remove it?
> + data = tpm_size >> 8 & 0x00ff;
I had to google to figure out which operator took precedence here, please add some parenthesis.
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_size & 0x00ff;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
IIRC Peter fixed this in the I2C driver -- where you can avoid
memcpy() of a single byte by using an assignment, please do.
> + latency -= 2;
> + }
> +
> + memcpy(data_buffer + i, tpm_data, tpm_size);
> + i += tpm_size;
> +
> + for (j = 0; j < platform_data->latency + 1; j++) {
> + data = TPM_DUMMY_BYTE;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + }
Isn't the above loop just this?
memset(&data_buffer[i], TPM_DUMMY_BYTE, platform_data->latency + 1);
> + xfer.len = i;
> + spi_message_init(&msg);
> + spi_message_add_tail(&xfer, &msg);
> + value = spi_sync(dev, &msg);
> +
> + if (value == 0) {
> + j = i - 1 - j;
> + for (; j < i && ((u8 *)xfer.rx_buf)[j] == 0; j++)
> + ;
> +
> + if (((u8 *)xfer.rx_buf)[j] != 0)
> + value = ((u8 *)xfer.rx_buf)[j];
Code like this is where vague variable names make it difficult. Can you rename i and j here? j is the number of dummy bytes and i is the total length of the transfer, right?
> + }
> +
> + return value;
> +} /* write8_reg() */
> +
> +/*
> + * read8_reg
> + * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be read
> + * @param: tpm_data, the TPM response
> + * @param: tpm_size, tpm TPM response size to read.
> + * @return: number of byte read successfully: should be one if success.
> + */
> +static u8 read8_reg(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
> +{
> + u8 data;
> + int i = 0, j;
> + int value = 0;
> + struct spi_device *dev = (struct spi_device *)tpm->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + u8 *data_buffer = platform_data->tpm_spi_buffer[0];
> + struct spi_transfer xfer = {
> + .tx_buf = data_buffer,
> + .rx_buf = platform_data->tpm_spi_buffer[1],
> + };
> + struct spi_message msg;
> +
> + u8 latency = platform_data->latency + tpm_size + 1;
> +
> + FUNC_ENTER();
> + /* Pre-Header */
> +
> + data = tpm->vendor.locality;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_register;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> +
> + for (j = 0; j < latency; j++) {
> + data = TPM_DUMMY_BYTE;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + }
> + xfer.len = i;
> +
> + /* header + status byte + size of the data + status byte */
> + spi_message_init(&msg);
> + spi_message_add_tail(&xfer, &msg);
> + value = spi_sync(dev, &msg);
> + if (tpm_size > 0 && value == 0) {
> + j = 2;
> + for (; j < i && ((u8 *)xfer.rx_buf)[j] == 0; j++)
> + ;
> +
> + if (j + 1 < i) {
> + value = ((u8 *)xfer.rx_buf)[j];
> +
> + if (tpm_size > 0)
> + memcpy(tpm_data, xfer.rx_buf + j + 1, tpm_size);
> + }
> + }
> + return value;
> +} /* read8_reg() */
Same comments as write8_reg -- converge into simpler memcpy/memset's where you can, rename variables.
> +
> +/*
> + * SPI_WRITE_DATA
> + * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be written
> + * @param: tpm_data, the tpm_data to write inside the tpm_register
> + * @param: tpm_size, The length of the data
> + * @return: number of byte written successfully: should be one if success.
Why would one be success if it returns the number of bytes written?
> + */
> +static u32 SPI_WRITE_DATA(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
An all caps function name will make me think its a macro, please use lower case.
> +{
> + u8 value = 0;
> +
> + FUNC_ENTER();
> +
> + value = write8_reg(tpm, tpm_register, tpm_data, tpm_size);
> +
> + switch (value) {
> + case TPM_ST_SPI_OK:
> + return TPM_ST_SPI_OK;
> + case 0:
> + return 0;
> + default:
> + return -EBUSY;
> + }
> +} /* SPI_WRITE_DATA() */
> +
> +/*
> + * SPI_READ_DATA
> + * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be read
> + * @param: tpm_data, the TPM response
> + * @param: tpm_size, tpm TPM response size to read.
> + * @return: number of byte read successfully: should be one if success.
> + */
> +static u32 SPI_READ_DATA(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
> +{
> + u8 value = 0;
> +
> + FUNC_ENTER();
> +
> + value = read8_reg(tpm, tpm_register, tpm_data, tpm_size);
> +
> + switch (value) {
> + case TPM_ST_SPI_OK:
> + return TPM_ST_SPI_OK;
> + case 0:
> + return 0;
> + default:
> + return -EBUSY;
> + }
> +} /* SPI_READ_DATA () */
> +
> +/*
> + * clear_interruption
> + * clear the TPM interrupt register.
> + * @param: tpm, the chip description
> + */
> +static void clear_interruption(struct tpm_chip *tpm) {
> + u8 interrupt;
> + SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
> + /* Clear interrupts handled with TPM_EOI */
> + SPI_WRITE_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
> + SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1); } /*
> +clear_interruption() */
> +
> +/*
> + * _wait_for_interrupt_serirq_timeout
> + * @param: tpm, the chip description
> + * @param: timeout, the timeout of the interrupt
> + * @return: the status of the interruption.
> + */
> +static int _wait_for_interrupt_serirq_timeout(struct tpm_chip *chip,
> + unsigned long timeout)
> +{
> + unsigned long status;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + status = wait_for_completion_interruptible_timeout(
> + &pin_infos->irq_detection, timeout);
> + if (status > 0)
> + enable_irq(gpio_to_irq(pin_infos->io_serirq));
> + gpio_direction_input(pin_infos->io_serirq);
> +
> + return status;
> +} /* wait_for_interrupt_serirq_timeout() */
> +
> +unsigned long wait_for_serirq_timeout(struct tpm_chip *chip, bool condition,
> + unsigned long timeout)
> +{
> + unsigned long status = 0;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
pin_infos isn't used here, please remove.
> + status = _wait_for_interrupt_serirq_timeout(chip, timeout);
> + if (!status) {
> + status = -EBUSY;
> + goto wait_end;
> + }
> + clear_interruption(chip);
> + if (condition)
> + status = 1;
> +
> +wait_end:
> + return status;
> +}
> +
> +
> +/*
> + * tpm_stm_spi_cancel, cancel is not implemented.
> + * @param: chip, the tpm chip description as specified in
> + * driver/char/tpm/tpm.h.
> + */
> +static void tpm_stm_spi_cancel(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data = TPM_STS_COMMAND_READY;
> + client = (struct spi_device *)chip->vendor.iobase;
client is unused?
> + FUNC_ENTER();
> +
> + /* this causes the current command to be aborted */
> + SPI_WRITE_DATA(chip, TPM_STS, &data, 1); } /* tpm_stm_spi_cancel()
> +*/
> +
> +/*
> + * tpm_stm_spi_status return the TPM_STS register
> + * @param: chip, the tpm chip description
> + * @return: the TPM_STS register value.
> + */
> +static u8 tpm_stm_spi_status(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data;
> + client = (struct spi_device *)chip->vendor.iobase;
client is unused?
> +
> + FUNC_ENTER();
> +
> + SPI_READ_DATA(chip, TPM_STS, &data, 1);
> + return data;
> +} /* tpm_stm_spi_status() */
> +
> +
> +
> +/*
> + * check_locality if the locality is active
> + * @param: chip, the tpm chip description
> + * @return: the active locality or -EACCESS.
> + */
> +static int check_locality(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data;
> + u8 status;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
client is unused?
> +
> + status = SPI_READ_DATA(chip, TPM_ACCESS, &data, 1);
> + if (status && (data &
> + (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID)) ==
> + (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID))
> + return chip->vendor.locality;
> +
> + return -EACCES;
> +} /* check_locality() */
> +
> +/*
> + * request_locality request the TPM locality
> + * @param: chip, the chip description
> + * @return: the active locality or EACCESS.
> + */
> +static int request_locality(struct tpm_chip *chip) {
> + unsigned long stop;
> + long rc;
> + u8 data;
> + struct spi_device *client;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
client is unused?
> + /* Check locality */
> + if (check_locality(chip) == chip->vendor.locality)
> + return chip->vendor.locality;
> +
> + /* Request locality */
> + data = TPM_ACCESS_REQUEST_USE;
> + rc = SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1);
> + if (rc < 0)
> + goto end;
> +
> + /* wait for burstcount */
> + if (chip->vendor.irq) {
> + rc = wait_for_serirq_timeout(chip, (check_locality
> + (chip) >= 0),
> + chip->vendor.timeout_a);
> + if (rc > 0)
> + return chip->vendor.locality;
> + } else {
> + stop = jiffies + chip->vendor.timeout_a;
> + do {
> + if (check_locality(chip) >= 0)
> + return chip->vendor.locality;
> + msleep(TPM_TIMEOUT);
> + } while (time_before(jiffies, stop));
> + }
> +end:
> + return -EACCES;
> +} /* request_locality() */
> +
> +/*
> + * release_locality release the active locality
> + * @param: chip, the tpm chip description.
> + */
> +static void release_locality(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
client is unused?
> + data = TPM_ACCESS_ACTIVE_LOCALITY;
> + SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1); } /*
> +release_locality()*/
> +
> +/*
> + * get_burstcount return the burstcount address 0x19 0x1A
> + * @param: chip, the chip description
> + * return: the burstcount.
> + */
> +static int get_burstcount(struct tpm_chip *chip) {
> + unsigned long stop;
> + u32 burstcnt, status;
> + u8 tpm_reg, temp;
> +
> + FUNC_ENTER();
> +
> + /* wait for burstcount */
> + /* which timeout value, spec has 2 answers (c & d) */
> + stop = jiffies + chip->vendor.timeout_d;
> + do {
> + tpm_reg = TPM_STS + 1;
> + status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
> + if (status < 0)
> + goto end;
> +
> + tpm_reg = tpm_reg + 1;
> + burstcnt = temp;
> + status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
> + if (status < 0)
> + goto end;
> +
> + burstcnt |= temp << 8;
> + if (burstcnt)
> + return burstcnt;
> + msleep(TPM_TIMEOUT);
> + } while (time_before(jiffies, stop));
> +
> +end:
> + return -EBUSY;
> +} /* get_burstcount() */
> +
> +/*
> + * wait_for_stat wait for a TPM_STS value
> + * @param: chip, the tpm chip description
> + * @param: mask, the value mask to wait
> + * @param: timeout, the timeout
> + * @param: queue, the wait queue.
> + * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
> + */
> +static int wait_for_stat(struct tpm_chip *chip, u8 mask, unsigned long timeout,
> + wait_queue_head_t *queue)
queue is unused?
> +{
> + unsigned long stop;
> + long rc;
> + u8 status;
> +
> + FUNC_ENTER();
> +
> + /* check current status */
> + status = tpm_stm_spi_status(chip);
> + if (!chip->vendor.irq && (status & mask) == mask)
> + return 0;
> +
> + if (chip->vendor.irq) {
> + rc = wait_for_serirq_timeout(chip, ((tpm_stm_spi_status
> + (chip) & mask) ==
> + mask), timeout);
> + if (rc > 0)
> + return 0;
> + } else {
> + stop = jiffies + timeout;
> + do {
> + msleep(TPM_TIMEOUT);
> + status = tpm_stm_spi_status(chip);
> + if ((status & mask) == mask)
> + return 0;
> + } while (time_before(jiffies, stop));
> + }
> + return -ETIME;
> +} /* wait_for_stat() */
> +
> +/*
> + * recv_data receive data
> + * @param: chip, the tpm chip description
> + * @param: buf, the buffer where the data are received
> + * @param: count, the number of data to receive
> + * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
> + */
> +static int recv_data(struct tpm_chip *chip, u8 *buf, size_t count) {
> + u32 size = 0, burstcnt, status, len;
> + struct spi_device *client;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
client is unused?
> +
> + while (size < count &&
> + wait_for_stat(chip,
> + TPM_STS_DATA_AVAIL | TPM_STS_VALID,
> + chip->vendor.timeout_c,
> + &chip->vendor.read_queue)
> + == 0) {
> + burstcnt = get_burstcount(chip);
> + len = min_t(int, burstcnt, count - size);
> + status = SPI_READ_DATA(chip, TPM_DATA_FIFO, buf + size, len);
> + if (status < 0)
> + return status;
> +
> +
> + size += len;
> + }
> + return size;
> +}
> +
> +/*
> + * tpm_ioserirq_handler the serirq irq handler
> + * @param: irq, the tpm chip description
> + * @param: dev_id, the description of the chip
> + * @return: the status of the handler.
> + */
> +static irqreturn_t tpm_ioserirq_handler(int irq, void *dev_id) {
> + struct tpm_chip *chip = dev_id;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + disable_irq_nosync(irq);
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + complete(&pin_infos->irq_detection);
> + return IRQ_HANDLED;
> +} /* tpm_ioserirq_handler() */
> +
> +/*
> + * tpm_stm_spi_send send TPM commands through the SPI bus.
> + * @param: chip, the tpm chip description
> + * @param: buf, the tpm command buffer
> + * @param: len, the tpm command size
> + * @return: In case of success the number of bytes sent.
> + * In other case, a < 0 value describing the issue.
> + */
> +static int tpm_stm_spi_send(struct tpm_chip *chip, unsigned char *buf,
> + size_t len)
> +{
> + u32 ret = 0, ordinal,
> + status, burstcnt = 0, i, size = 0;
> + u8 data;
> +
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + FUNC_ENTER();
> +
> + if (chip == NULL)
> + return -EBUSY;
> + if (len < TPM_HEADER_SIZE)
> + return -EBUSY;
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
pin_infos and client are unused?
> +
> + ordinal = be32_to_cpu(*((__be32 *)(buf + 6)));
ordinal is unused?
> +
> + ret = request_locality(chip);
> + if (ret < 0)
> + return ret;
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_COMMAND_READY) == 0) {
> + tpm_stm_spi_cancel(chip);
> + if (wait_for_stat
> + (chip, TPM_STS_COMMAND_READY, chip->vendor.timeout_b,
> + &chip->vendor.int_queue) < 0) {
> + ret = -ETIME;
> + goto out_err;
> + }
> + }
> +
> + for (i = 0; i < len - 1;) {
> + burstcnt = get_burstcount(chip);
> + size = min_t(int, len - i - 1, burstcnt);
burstcnt can be -EBUSY here, which would cause size to become a large negative number. Better to check its sane here before using it.
> + ret = SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf, size);
> + if (ret < 0)
> + goto out_err;
> + i += size;
> + }
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_DATA_EXPECT) == 0) {
> + ret = -EIO;
> + goto out_err;
> + }
> +
> + /* write last byte */
> + SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf + len - 1, 1);
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_DATA_EXPECT) != 0) {
> + ret = -EIO;
> + goto out_err;
> + }
> +
> + /* go and do it */
> + data = TPM_STS_GO;
> + ret = SPI_WRITE_DATA(chip, TPM_STS, &data, 1);
> + if (ret < 0)
> + goto out_err;
> +
> + return len;
> +out_err:
> + tpm_stm_spi_cancel(chip);
> + release_locality(chip);
> + return ret;
> +}
> +
> +/*
> + * tpm_stm_spi_recv received TPM response through the SPI bus.
> + * @param: chip, the tpm chip description
> + * @param: buf, the tpm command buffer
> + * @param: len, the tpm command size
> +* @return: In case of success the number of bytes received.
> + * In other case, a < 0 value describing the issue.
> + */
> +static int tpm_stm_spi_recv(struct tpm_chip *chip, unsigned char *buf,
> + size_t count)
> +{
> + int size = 0;
> + int expected;
> +
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
pin_infos and client are unused?
> +
> +
> + if (chip == NULL)
> + return -EBUSY;
> + if (count < TPM_HEADER_SIZE) {
> + size = -EIO;
> + goto out;
> + }
> +
> + size = recv_data(chip, buf, TPM_HEADER_SIZE);
> +
> + /* read first 10 bytes, including tag, paramsize, and result */
> + if (size < TPM_HEADER_SIZE) {
> + dev_err(chip->dev, "Unable to read header\n");
> + goto out;
> + }
> +
> + expected = be32_to_cpu(*(__be32 *)(buf + 2));
> + if (expected > count) {
> + size = -EIO;
> + goto out;
> + }
> +
> + size += recv_data(chip, &buf[TPM_HEADER_SIZE],
> + expected - TPM_HEADER_SIZE);
> + if (size < expected) {
> + dev_err(chip->dev, "Unable to read remainder of result\n");
> + size = -ETIME;
> + goto out;
> + }
> +
> +out:
> + chip->vendor.cancel(chip);
> + release_locality(chip);
> + return size;
> +}
> +
> +
> +static const struct file_operations tpm_st33_spi_fops = {
> + .owner = THIS_MODULE,
> + .llseek = no_llseek,
> + .read = tpm_read,
> + .write = tpm_write,
> + .open = tpm_open,
> + .release = tpm_release,
> +};
> +
> +static DEVICE_ATTR(pubek, S_IRUGO, tpm_show_pubek, NULL); static
> +DEVICE_ATTR(pcrs, S_IRUGO, tpm_show_pcrs, NULL); static
> +DEVICE_ATTR(enabled, S_IRUGO, tpm_show_enabled, NULL); static
> +DEVICE_ATTR(active, S_IRUGO, tpm_show_active, NULL); static
> +DEVICE_ATTR(owned, S_IRUGO, tpm_show_owned, NULL); static
> +DEVICE_ATTR(temp_deactivated, S_IRUGO, tpm_show_temp_deactivated,
> +NULL); static DEVICE_ATTR(caps, S_IRUGO, tpm_show_caps_1_2, NULL);
> +static DEVICE_ATTR(cancel, S_IWUSR | S_IWGRP, NULL,
> +tpm_store_cancel);
> +
> +static struct attribute *stm_tpm_attrs[] = {
> + &dev_attr_pubek.attr,
> + &dev_attr_pcrs.attr,
> + &dev_attr_enabled.attr,
> + &dev_attr_active.attr,
> + &dev_attr_owned.attr,
> + &dev_attr_temp_deactivated.attr,
> + &dev_attr_caps.attr,
> + &dev_attr_cancel.attr, NULL,
> +};
> +
> +static struct attribute_group stm_tpm_attr_grp = {
> + .attrs = stm_tpm_attrs
> +};
> +
> +static struct tpm_vendor_specific st_spi_tpm = {
> + .send = tpm_stm_spi_send,
> + .recv = tpm_stm_spi_recv,
> + .cancel = tpm_stm_spi_cancel,
> + .status = tpm_stm_spi_status,
> + .attr_group = &stm_tpm_attr_grp,
> + .miscdev = {.fops = &tpm_st33_spi_fops,}, };
> +
> +static int evaluate_latency(struct tpm_chip *chip) {
> + int latency = 0;
> + struct spi_device *dev = (struct spi_device *)chip->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + int status = 0;
> + u8 data;
> +
> + for (; status == 0x00 && latency < MAX_SPI_LATENCY; latency++) {
> + platform_data->latency = latency;
> + status = SPI_READ_DATA(chip, TPM_INTF_CAPABILITY, &data, 1);
> + }
> + return latency - 1;
> +} /* evaluate_latency() */
> +
> +static int interrupts;
> +module_param(interrupts, int, 0444);
> +MODULE_PARM_DESC(interrupts, "Enable interrupts");
> +
> +static int power_mgt = 1;
> +module_param(power_mgt, int, 0444);
> +MODULE_PARM_DESC(power_mgt, "Power Management");
> +
> +/*
> + * tpm_st33_spi_probe initialize the TPM device
> + * @param: client, the spi_device drescription (TPM SPI description).
> + * @param: id, the spi_device_id struct.
> + * @return: 0 in case of success.
> + * -1 in other case.
> + */
> +static int
> +tpm_st33_spi_probe(struct spi_device *dev) {
> + u32 err;
> + u8 intmask;
> + struct tpm_chip *chip;
> + struct st33zp24_platform_data *platform_data;
> +
> + FUNC_ENTER();
> +
> + err = 0;
> +
> + /* Check SPI platform functionnalities */
> + if (dev == NULL) {
> + pr_info("dev is NULL. exiting.\n");
> + err = -ENODEV;
> + goto end;
> + }
> +
> + chip = tpm_register_hardware(&dev->dev, &st_spi_tpm);
> + if (!chip) {
> + err = -ENODEV;
> + goto end;
> + }
> +
> + /* Allocation of SPI buffers MISO and MOSI */
> + /* Size is as follow: */
> + /* Request burstcount value = 0x800 = 2048 */
> + /* + */
> + /* Response burstcount value = 0x400 = 1024 */
> + /* + */
> + /* At least: */
> + /* 1 byte for direction/locality */
> + /* 1 byte tpm tis register */
> + /* 2 bytes spi data length (for request only) */
> + /* 2 latency bytes */
> + /* 1 status byte */
> + /* = 2048 + 1024 + 7 */
> + /* We reserved 2048 + 1024 + 20 in case latency byte */
> + /* change */
> + platform_data = dev->dev.platform_data;
> + platform_data->tpm_spi_buffer[0] =
> + kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
> + TPM_DIGEST_SIZE) * sizeof(u8), GFP_KERNEL);
> + if (platform_data->tpm_spi_buffer[0] == NULL) {
> + err = -ENOMEM;
> + goto _tpm_clean_answer;
> + }
> + platform_data->tpm_spi_buffer[1] =
> + kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
> + TPM_DIGEST_SIZE) * sizeof(u8) , GFP_KERNEL);
> + if (platform_data->tpm_spi_buffer[1] == NULL) {
> + err = -ENOMEM;
> + goto _tpm_clean_response;
> + }
> +
> + chip->vendor.iobase = dev;
> +
> + /* Default timeouts */
> + chip->vendor.timeout_a = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.timeout_b = msecs_to_jiffies(TIS_LONG_TIMEOUT);
> + chip->vendor.timeout_c = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.timeout_d = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.locality = LOCALITY0;
> +
> + if (power_mgt) {
> + err = gpio_request(platform_data->io_lpcpd, "TPM IO_LPCPD");
> + if (err)
> + goto _gpio_init1;
> + gpio_set_value(platform_data->io_lpcpd, 1);
> + }
> +
> + platform_data->latency = evaluate_latency(chip);
> + if (platform_data->latency <= 0x00) {
> + err = -ENODEV;
> + goto _gpio_init1;
> + }
> +
> + /* Enable interrupt */
> + /* Register GPIO pin through generic Linux GPIO API */
> + if (interrupts) {
> + init_completion(&platform_data->irq_detection);
> + if (request_locality(chip) != LOCALITY0) {
> + err = -ENODEV;
> + goto _tpm_clean_response;
> + }
> + err = gpio_request(platform_data->io_serirq, "TPM IO_SERIRQ");
> + if (err)
> + goto _gpio_init2;
> +
> + /* Clear all existing */
> + clear_interruption(chip);
> + err = request_irq(gpio_to_irq(platform_data->io_serirq),
> + &tpm_ioserirq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_SHARED,
> + "TPM SERIRQ management", chip);
> + if (err < 0) {
> + pr_info("TPM SERIRQ signals %d not available\n",
> + gpio_to_irq(
> + platform_data->io_serirq));
> + goto _irq_set;
> + }
> + err = SPI_READ_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + intmask |= TPM_INTF_CMD_READY_INT
> + | TPM_INTF_FIFO_AVALAIBLE_INT
> + | TPM_INTF_WAKE_UP_READY_INT
> + | TPM_INTF_LOC4SOFTRELEASE_INT
> + | TPM_INTF_LOCALITY_CHANGE_INT
> + | TPM_INTF_STS_VALID_INT
> + | TPM_INTF_DATA_AVAIL_INT;
> +
> + err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + intmask = TPM_GLOBAL_INT_ENABLE;
> + err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE + 3, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + err = SPI_READ_DATA(chip, TPM_INT_STATUS, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + chip->vendor.irq = interrupts;
> +
> + tpm_gen_interrupt(chip);
> + }
> +
> + tpm_get_timeouts(chip);
> +
> + /* attach chip datas to client */
> + spi_set_drvdata(dev, chip);
> + platform_data->bchipf = false;
> +
> + pr_info("TPM SPI Initialized\n");
> + return 0;
> +_irq_set:
> + free_irq(gpio_to_irq(platform_data->io_serirq), chip);
> +_gpio_init2:
> + if (platform_data && interrupts)
> + gpio_free(platform_data->io_serirq);
> +_gpio_init1:
> + if (platform_data && power_mgt)
> + gpio_free(platform_data->io_lpcpd);
> +_tpm_clean_response:
> + tpm_remove_hardware(chip->dev);
> + if (platform_data->tpm_spi_buffer[1] != NULL) {
> + kfree(platform_data->tpm_spi_buffer[1]);
> + platform_data->tpm_spi_buffer[1] = NULL;
> + }
> +_tpm_clean_answer:
> + if (platform_data->tpm_spi_buffer[0] != NULL) {
> + kfree(platform_data->tpm_spi_buffer[0]);
> + platform_data->tpm_spi_buffer[0] = NULL;
> + }
> +
> + platform_data->bchipf = true;
Please take a look at git commit 3d7a7bd7 and make the same changes. The way these labels are jumped to can use some cleaning up. I suspect that you can also remove bchipf here like in 1fbc5e95356a4600fab3a04a82dc8bb49591aedd.
Thanks,
Kent
> +end:
> + pr_info("TPM SPI initialisation fail\n");
> + return err;
> +}
> +
> +/*
> + * tpm_st33_spi_remove remove the TPM device
> + * @param: client, the spi_device drescription (TPM SPI description).
> + clear_bit(0, &chip->is_open);
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_remove(struct spi_device *client) {
> + struct tpm_chip *chip = (struct tpm_chip *)spi_get_drvdata(client);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
> +
> + FUNC_ENTER();
> +
> + if (pin_infos != NULL) {
> + gpio_free(pin_infos->io_lpcpd);
> +
> + /* Check if chip has been previously clean */
> + if (pin_infos->bchipf != true)
> + tpm_remove_hardware(chip->dev);
> + if (pin_infos->tpm_spi_buffer[1] != NULL) {
> + kfree(pin_infos->tpm_spi_buffer[1]);
> + pin_infos->tpm_spi_buffer[1] = NULL;
> + }
> + if (pin_infos->tpm_spi_buffer[0] != NULL) {
> + kfree(pin_infos->tpm_spi_buffer[0]);
> + pin_infos->tpm_spi_buffer[0] = NULL;
> + }
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * tpm_st33_spi_pm_suspend suspend the TPM device
> + * Added: Work around when suspend and no tpm application is running,
> +suspend
> + * may fail because chip->data_buffer is not set (only set in
> +tpm_open in Linux
> + * TPM core)
> + * @param: client, the spi_device drescription (TPM SPI description).
> + * @param: mesg, the power management message.
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_pm_suspend(struct spi_device *client,
> + pm_message_t mesg)
> +{
> + struct tpm_chip *chip =
> + (struct tpm_chip *)spi_get_drvdata(client);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
> + int ret = 0;
> +
> + if (power_mgt) {
> + gpio_set_value(pin_infos->io_lpcpd, 0);
> + } else {
> + if (chip->data_buffer == NULL)
> + chip->data_buffer = pin_infos->tpm_spi_buffer[0];
> + ret = tpm_pm_suspend(&client->dev);
> + }
> + return ret;
> +} /* tpm_st33_spi_suspend() */
> +
> +/*
> + * tpm_st33_spi_pm_resume resume the TPM device
> + * @param: spi, the spi_device drescription (TPM SPI description).
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_pm_resume(struct spi_device *spi) {
> + struct tpm_chip *chip =
> + (struct tpm_chip *)spi_get_drvdata(spi);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
> +
> + int ret = 0;
> + if (power_mgt) {
> + gpio_set_value(pin_infos->io_lpcpd, 1);
> + ret = wait_for_serirq_timeout(chip,
> + (chip->vendor.status(chip) &&
> + TPM_STS_VALID) == TPM_STS_VALID,
> + chip->vendor.timeout_b);
> + } else {
> + if (chip->data_buffer == NULL)
> + chip->data_buffer = pin_infos->tpm_spi_buffer[0];
> + ret = tpm_pm_resume(&spi->dev);
> + if (!ret)
> + tpm_do_selftest(chip);
> + }
> + return ret;
> +} /* tpm_st33_spi_pm_resume() */
> +
> +static struct spi_driver tpm_st33_spi_driver = {
> + .driver = {
> + .owner = THIS_MODULE,
> + .name = TPM_ST33_SPI,
> + },
> + .probe = tpm_st33_spi_probe,
> + .remove = tpm_st33_spi_remove,
> + .resume = tpm_st33_spi_pm_resume,
> + .suspend = tpm_st33_spi_pm_suspend,
> +};
> +
> +/*
> + * tpm_st33_spi_init initialize driver
> + * @return: 0 if successful, else non zero value.
> + */
> +static int __init tpm_st33_spi_init(void) {
> + FUNC_ENTER();
> + return spi_register_driver(&tpm_st33_spi_driver);
> +}
> +
> +/*
> + * tpm_st33_spi_exit The kernel calls this function during unloading
> +the
> + * module or during shut down process */ static void __exit
> +tpm_st33_spi_exit(void) {
> + FUNC_ENTER();
> + spi_unregister_driver(&tpm_st33_spi_driver);
> +}
> +
> +module_init(tpm_st33_spi_init);
> +module_exit(tpm_st33_spi_exit);
> +
> +MODULE_AUTHOR("Christophe Ricard (tpmsupport@...com)");
> +MODULE_DESCRIPTION("STM TPM SPI ST33 Driver");
> +MODULE_VERSION("1.2.0"); MODULE_LICENSE("GPL");
> diff --git a/drivers/char/tpm/tpm_spi_stm_st33.h
> b/drivers/char/tpm/tpm_spi_stm_st33.h
> new file mode 100644
> index 0000000..42bae6f
> --- /dev/null
> +++ b/drivers/char/tpm/tpm_spi_stm_st33.h
> @@ -0,0 +1,75 @@
> +/*
> + * STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
> + * Copyright (C) 2009, 2010 STMicroelectronics
> + *
> + * This program is free software; you can redistribute it and/or
> +modify
> + * it under the terms of the GNU General Public License as published
> +by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> +along
> + * with this program; if not, write to the Free Software Foundation,
> +Inc.,
> + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> + *
> + * STMicroelectronics version 1.2.0, Copyright (C) 2010
> + * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> + * This is free software, and you are welcome to redistribute it
> + * under certain conditions.
> + *
> + * @Author: Christophe RICARD tpmsupport@...com
> + *
> + * @File: tpm_spi_stm_st33.h
> + *
> + * @Date: 09/15/2010
> + */
> +#ifndef __STM_ST33_TPM_SPI_MAIN_H__
> +#define __STM_ST33_TPM_SPI_MAIN_H__
> +
> +#include <linux/pci.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/fs.h>
> +#include <linux/miscdevice.h>
> +
> +#define MINOR_NUM_SPI 224
> +
> +#define TPM_ACCESS (0x0)
> +#define TPM_STS (0x18)
> +#define TPM_HASH_END (0x20)
> +#define TPM_DATA_FIFO (0x24)
> +#define TPM_HASH_DATA (0x24)
> +#define TPM_HASH_START (0x28)
> +#define TPM_INTF_CAPABILITY (0x14)
> +#define TPM_INT_STATUS (0x10)
> +#define TPM_INT_ENABLE (0x08)
> +
> +#define TPM_DUMMY_BYTE 0x00
> +#define TPM_WRITE_DIRECTION 0x80
> +#define TPM_HEADER_SIZE 10
> +#define TPM_BUFSIZE 2048
> +
> +/* ioctl commands */
> +#define TPMIOC_CANCEL _IO('T', 0x00)
> +#define TPMIOC_TRANSMIT _IO('T', 0x01)
> +#define TPMIOC_HASH _IO('T', 0x02)
> +#define TPMIOC_CHANGELOCALITY _IO('T', 0x03)
> +
> +#define LOCALITY0 0
> +#define LOCALITY4 4
> +
> +#define TPM_ST_SPI_OK 0x5A
> +
> +
> +#define MAX_SPI_LATENCY 15
> +
> +struct st_tpm_hash_t {
> + int size;
> + u8 *data;
> +};
> +
> +#endif /* __STM_ST33_TPM_SPI_MAIN_H__ */
> diff --git a/include/linux/spi/tpm_spi_stm_st33.h
> b/include/linux/spi/tpm_spi_stm_st33.h
> new file mode 100644
> index 0000000..d7e10db
> --- /dev/null
> +++ b/include/linux/spi/tpm_spi_stm_st33.h
> @@ -0,0 +1,44 @@
> +/*
> +* STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
> +* Copyright (C) 2009, 2010 STMicroelectronics
> +* Christophe RICARD tpmsupport@...com
> +* This program is free software; you can redistribute it and/or
> +modify
> +* it under the terms of the GNU General Public License as published
> +by
> +* the Free Software Foundation; either version 2 of the License, or
> +* (at your option) any later version.
> +*
> +* This program is distributed in the hope that it will be useful,
> +* but WITHOUT ANY WARRANTY; without even the implied warranty of
> +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +* GNU General Public License for more details.
> +*
> +* You should have received a copy of the GNU General Public License
> +along
> +* with this program; if not, write to the Free Software Foundation,
> +Inc.,
> +* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> +*
> +* STMicroelectronics version 1.2.0, Copyright (C) 2010
> +* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> +* This is free software, and you are welcome to redistribute it
> +* under certain conditions.
> +*
> +* @File: tpm_spi_stm_st33.h
> +*
> +* @Date: 06/15/2008
> +*/
> +#ifndef __STM_ST33_TPM_SPI_H__
> +#define __STM_ST33_TPM_SPI_H__
> +
> +#include <linux/spi/spi.h>
> +
> +#define TPM_ST33_SPI "st33zp24_spi"
> +
> +struct st33zp24_platform_data {
> + int io_serirq;
> + int io_lpcpd;
> + int latency;
> + bool bchipf;
> + u8 *tpm_spi_buffer[2]; /* 0 Request 1 Response */
> + struct completion irq_detection;
> +};
> +
> +#endif /* __STM_ST33_TPM_SPI_H__ */
> --
> 1.7.1
>
>
> ----------------------------------------------------------------------
> -------- Precog is a next-generation analytics platform capable of
> advanced analytics on semi-structured data. The platform includes APIs
> for building apps and a phenomenal toolset for data science.
> Developers can use our toolset for easy data analysis & visualization.
> Get a free account!
> http://www2.precog.com/precogplatform/slashdotnewsletter
> _______________________________________________
> tpmdd-devel mailing list
> tpmdd-devel@...ts.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/tpmdd-devel
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists