| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1366727607-27444-6-git-send-email-james.hogan@imgtec.com>
Date: Tue, 23 Apr 2013 15:33:24 +0100
From: James Hogan <james.hogan@...tec.com>
To: <linux-kernel@...r.kernel.org>
CC: Grant Likely <grant.likely@...retlab.ca>,
Rob Herring <rob.herring@...xeda.com>,
Linus Walleij <linus.walleij@...aro.org>,
<devicetree-discuss@...ts.ozlabs.org>,
James Hogan <james.hogan@...tec.com>,
Rob Landley <rob@...dley.net>, <linux-doc@...r.kernel.org>
Subject: [PATCH 5/8] pinctrl-tz1090: add TZ1090 pinctrl driver
Add a pin control driver for the main pins on the TZ1090 SoC. This
doesn't include the low-power pins as they're controlled separately via
the Powerdown Controller (PDC) registers.
Signed-off-by: James Hogan <james.hogan@...tec.com>
Cc: Grant Likely <grant.likely@...retlab.ca>
Cc: Rob Herring <rob.herring@...xeda.com>
Cc: Rob Landley <rob@...dley.net>
Cc: Linus Walleij <linus.walleij@...aro.org>
Cc: linux-doc@...r.kernel.org
---
.../bindings/pinctrl/img,tz1090-pinctrl.txt | 214 +++
arch/metag/Kconfig.soc | 2 +
arch/metag/boot/dts/tz1090.dtsi | 6 +
drivers/pinctrl/Kconfig | 6 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-tz1090.c | 2018 ++++++++++++++++++++
drivers/pinctrl/pinctrl-tz1090.h | 58 +
7 files changed, 2305 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
create mode 100644 drivers/pinctrl/pinctrl-tz1090.c
create mode 100644 drivers/pinctrl/pinctrl-tz1090.h
diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
new file mode 100644
index 0000000..4751795
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
@@ -0,0 +1,214 @@
+ImgTec TZ1090 pin controller
+
+Required properties:
+- compatible: "img,tz1090-pinctrl"
+- reg: Should contain the register physical address and length of the pad
+ configuration registers (CR_PADS_* and CR_IF_CTL0).
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+TZ1090's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function. For this reason, even seemingly boolean
+values are actually tristates in this binding: unspecified, off, or on.
+Unspecified is represented as an absent property, and off/on are represented as
+integer values 0 and 1.
+
+The exception to that rule is the select config. The CR_PADS_GPIO_SELECT{0,1,2}
+registers select between the serial interface (where an internal peripheral such
+as the SPI block controls the pin) and the GPIO interface (where the pin can be
+controlled by the other GPIO registers). This defaults to the GPIO interface for
+all pins, so muxing a function onto a pin group will set all pins to the serial
+interface. This can be overridden by claiming one of the pins as a GPIO, or
+explicitly setting the select config to override this behaviour (see below).
+
+Required subnode-properties:
+- pins : An array of strings. Each string contains the name of a pin or group.
+ Valid values for these names are listed below.
+
+Optional subnode-properties:
+- function: A string containing the name of the function to mux to the pin or
+ group. Valid values for function names are listed below, including which
+ pingroups can be muxed to them.
+- select: Integer, force the pin(s) to the GPIO interface so they cannot be
+ controlled by internal peripherals.
+ 0: don't force (internal peripheral will have control of the pin(s) if
+ they're muxed and not selected for GPIO use).
+ 1: force gpio mode (internal peripheral will not control the pin(s))
+- pull: Integer, representing the pull-down/up to apply to the pin(s).
+ 0: tri-state
+ 1: pull-up
+ 2: pull-down
+ 3: repeater
+- schmitt: Integer, enable or disable Schmitt trigger mode for the pins.
+ 0: no hysteresis
+ 1: schmitt trigger
+- slew-rate: Integer, control slew rate of pins.
+ 0: slow (half frequency)
+ 1: fast
+- drive-strength: Integer, control drive strength of pins.
+ 0: 2mA
+ 1: 4mA
+ 2: 8mA
+ 4: 12mA
+
+Note that many of these properties are only valid for certain specific pins
+or groups. See the TZ1090 TRM for complete details regarding which groups
+support which functionality. The Linux pinctrl driver may also be a useful
+reference.
+
+Valid values for pin and group names are:
+
+ gpio pins:
+
+ These all support select and pull (which can also be provided to any of the
+ groups below to set it for all gpio pins in that group).
+
+ They also all support the "default" function (if they cannot be individually
+ muxed, see pdm_d and spi1_cs2 mux groups below).
+
+ ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7,
+ i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out,
+ i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on,
+ scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd,
+ sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
+ spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0,
+ spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0,
+ tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7,
+ tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5,
+ tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0,
+ tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7,
+ tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts,
+ uart0_rxd, uart0_txd, uart1_rxd, uart1_txd.
+
+ other pins:
+
+ These other pins are part of various pin groups below, but can't be
+ individually configured.
+
+ clk_out0, clk_out1, tck, tdi, tdo, tms, trst.
+
+ mux groups:
+
+ These all support function, and some support drive configs.
+
+ afe
+ pins: tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0, ant_sel1,
+ gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7.
+ function: afe, ts_out_0.
+ schmitt: supported.
+ slew-rate: supported.
+ drive-strength: supported.
+ pdm_d
+ pins: pdm_d.
+ function: pdm_dac, usb_vbus.
+ sdh
+ pins: sdh_cd, sdh_wp, sdh_clk_in.
+ function: sdh, sdio.
+ sdio
+ pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3.
+ function: sdio, sdh.
+ spi1_cs2
+ pins: spi1_cs2.
+ function: spi1_cs2, usb_vbus.
+ tft
+ pins: tft_red0, tft_red1, tft_red2, tft_red3,
+ tft_red4, tft_red5, tft_red6, tft_red7,
+ tft_green0, tft_green1, tft_green2, tft_green3,
+ tft_green4, tft_green5, tft_green6, tft_green7,
+ tft_blue0, tft_blue1, tft_blue2, tft_blue3,
+ tft_blue4, tft_blue5, tft_blue6, tft_blue7,
+ tft_vdden_gd, tft_panelclk, tft_blank_ls, tft_vsync_ns,
+ tft_hsync_nr, tft_vd12acb, tft_pwrsave.
+ function: tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1,
+ lcd_trace, phy_ringosc.
+ schmitt: supported.
+ slew-rate: supported.
+ drive-strength: supported.
+
+ drive groups:
+
+ These all support schmitt, slew-rate, and drive-strength.
+
+ jtag
+ pins: tck, trst, tdi, tdo, tms.
+ scb1
+ pins: scb1_sdat, scb1_sclk.
+ scb2
+ pins: scb2_sdat, scb2_sclk.
+ spi0
+ pins: spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din.
+ spi1
+ pins: spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din.
+ uart
+ pins: uart0_txd, uart0_rxd, uart0_rts, uart0_cts,
+ uart1_txd, uart1_rxd.
+ drive_i2s
+ pins: clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
+ i2s_lrclk_out, i2s_bclk_out, i2s_mclk.
+ drive_pdm
+ pins: clk_out0, pdm_b, pdm_a.
+ drive_scb0
+ pins: scb0_sclk, scb0_sdat, pdm_d, pdm_c.
+ drive_sdio
+ pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
+ sdh_wp, sdh_cd, sdh_clk_in.
+
+ convenience groups:
+
+ These are just convenient groupings of pins and don't support any drive
+ configs.
+
+ uart0
+ pins: uart0_cts, uart0_rts, uart0_rxd, uart0_txd.
+ uart1
+ pins: uart1_rxd, uart1_txd.
+ scb0
+ pins: scb0_sclk, scb0_sdat.
+ i2s
+ pins: i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
+ i2s_lrclk_out, i2s_mclk.
+
+Example:
+
+ pinctrl@...05800 {
+ #gpio-range-cells = <2>;
+ compatible = "img,tz1090-pinctrl";
+ reg = <0x02005800 0xe4>;
+ };
+
+Example board file extract:
+
+ pinctrl@...05800 {
+ uart0_default: uart0 {
+ uart0_cfg {
+ pins = "uart0_rxd",
+ "uart0_txd";
+ function = "default";
+ };
+ };
+ tft_default: tft {
+ tft_cfg {
+ pins = "tft";
+ function = "tft";
+ };
+ };
+ };
+
+ uart@...04b00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_default>;
+ };
diff --git a/arch/metag/Kconfig.soc b/arch/metag/Kconfig.soc
index 433befd..944dc30 100644
--- a/arch/metag/Kconfig.soc
+++ b/arch/metag/Kconfig.soc
@@ -20,6 +20,8 @@ config SOC_TZ1090
select METAG_LNKGET_AROUND_CACHE
select METAG_META21
select METAG_SMP_WRITE_REORDERING
+ select PINCTRL
+ select PINCTRL_TZ1090
help
This is a Toumaz Technology Xenif TZ1090 (A.K.A. Comet) SoC containing
a 2-threaded HTP.
diff --git a/arch/metag/boot/dts/tz1090.dtsi b/arch/metag/boot/dts/tz1090.dtsi
index 12d671c..ccbcbf1 100644
--- a/arch/metag/boot/dts/tz1090.dtsi
+++ b/arch/metag/boot/dts/tz1090.dtsi
@@ -41,5 +41,11 @@
<29 4 /* level */>, /* Perip 1 (IR) */
<31 4 /* level */>; /* Perip 2 (WDT) */
};
+
+ pinctrl: pinctrl@...05800 {
+ #gpio-range-cells = <2>;
+ compatible = "img,tz1090-pinctrl";
+ reg = <0x02005800 0xe4>;
+ };
};
};
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 34f51d2..5f8bfa8 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -196,6 +196,12 @@ config PINCTRL_TEGRA114
bool
select PINCTRL_TEGRA
+config PINCTRL_TZ1090
+ bool "Toumaz Xenif TZ1090 pin control driver"
+ depends on SOC_TZ1090
+ select PINMUX
+ select PINCONF
+
config PINCTRL_U300
bool "U300 pin controller driver"
depends on ARCH_U300
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index f82cc5b..1ae5596 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -40,6 +40,7 @@ obj-$(CONFIG_PINCTRL_TEGRA) += pinctrl-tegra.o
obj-$(CONFIG_PINCTRL_TEGRA20) += pinctrl-tegra20.o
obj-$(CONFIG_PINCTRL_TEGRA30) += pinctrl-tegra30.o
obj-$(CONFIG_PINCTRL_TEGRA114) += pinctrl-tegra114.o
+obj-$(CONFIG_PINCTRL_TZ1090) += pinctrl-tz1090.o
obj-$(CONFIG_PINCTRL_U300) += pinctrl-u300.o
obj-$(CONFIG_PINCTRL_COH901) += pinctrl-coh901.o
obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o
diff --git a/drivers/pinctrl/pinctrl-tz1090.c b/drivers/pinctrl/pinctrl-tz1090.c
new file mode 100644
index 0000000..5ec36b8
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-tz1090.c
@@ -0,0 +1,2018 @@
+/*
+ * Pinctrl driver for the Toumaz Xenif TZ1090 SoC
+ *
+ * Copyright (c) 2013, Imagination Technologies Ltd.
+ *
+ * Derived from Tegra code:
+ * Copyright (c) 2011-2012, NVIDIA CORPORATION. All rights reserved.
+ *
+ * Derived from code:
+ * Copyright (C) 2010 Google, Inc.
+ * Copyright (C) 2010 NVIDIA Corporation
+ * Copyright (C) 2009-2011 ST-Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+#include <asm/global_lock.h>
+#include <asm/soc-tz1090/gpio.h>
+
+#include "core.h"
+#include "pinctrl-tz1090.h"
+
+/* Register offsets from bank base address */
+#define REG_PINCTRL_SELECT 0x10
+#define REG_PINCTRL_SCHMITT 0x90
+#define REG_PINCTRL_PU_PD 0xa0
+#define REG_PINCTRL_SR 0xc0
+#define REG_PINCTRL_DR 0xd0
+#define REG_PINCTRL_IF_CTL 0xe0
+
+/**
+ * struct tz1090_function - TZ1090 pinctrl mux function
+ * @name: The name of the function, exported to pinctrl core.
+ * @groups: An array of pin groups that may select this function.
+ * @ngroups: The number of entries in @groups.
+ */
+struct tz1090_function {
+ const char *name;
+ const char * const *groups;
+ unsigned ngroups;
+};
+
+/**
+ * struct tz1090_muxdesc - TZ1090 individual mux description
+ * @funcs: Function for each mux value.
+ * @reg: Mux register offset. 0 if unsupported.
+ * @bit: Mux register bit. 0 if unsupported.
+ * @width: Mux field width. 0 if unsupported.
+ *
+ * A representation of a group of signals (possibly just one signal) in the
+ * TZ1090 which can be muxed to a set of functions or sub muxes.
+ */
+struct tz1090_muxdesc {
+ int funcs[5];
+ u16 reg;
+ u32 bit:5;
+ u32 width:5;
+};
+
+/**
+ * struct tz1090_pingroup - TZ1090 pin group
+ * @name: Name of pin group.
+ * @pins: Array of pin numbers in this pin group.
+ * @npins: Number of pins in this pin group.
+ * @mux: Top level mux.
+ * @drv: Drive control supported, 0 if unsupported.
+ * This means Schmitt, Slew, and Drive strength.
+ * @slw_bit: Slew register bit. 0 if unsupported.
+ * The same bit is used for Schmitt, and Drive (*2).
+ *
+ * A representation of a group of pins (possibly just one pin) in the TZ1090
+ * pin controller. Each group allows some parameter or parameters to be
+ * configured. The most common is mux function selection.
+ */
+struct tz1090_pingroup {
+ const char *name;
+ const unsigned int *pins;
+ unsigned int npins;
+ struct tz1090_muxdesc mux;
+
+ u32 drv:1;
+ u32 slw_bit:5;
+};
+
+/*
+ * Most pins affected by the pinmux can also be GPIOs. Define these first.
+ * These must match how the GPIO driver names/numbers its pins.
+ */
+#define _GPIO(offset) (GPIO_##offset)
+
+#define TZ1090_PIN_SDIO_CLK _GPIO(SDIO_CLK)
+#define TZ1090_PIN_SDIO_CMD _GPIO(SDIO_CMD)
+#define TZ1090_PIN_SDIO_D0 _GPIO(SDIO_D0)
+#define TZ1090_PIN_SDIO_D1 _GPIO(SDIO_D1)
+#define TZ1090_PIN_SDIO_D2 _GPIO(SDIO_D2)
+#define TZ1090_PIN_SDIO_D3 _GPIO(SDIO_D3)
+#define TZ1090_PIN_SDH_CD _GPIO(SDH_CD)
+#define TZ1090_PIN_SDH_WP _GPIO(SDH_WP)
+#define TZ1090_PIN_SPI0_MCLK _GPIO(SPI0_MCLK)
+#define TZ1090_PIN_SPI0_CS0 _GPIO(SPI0_CS0)
+#define TZ1090_PIN_SPI0_CS1 _GPIO(SPI0_CS1)
+#define TZ1090_PIN_SPI0_CS2 _GPIO(SPI0_CS2)
+#define TZ1090_PIN_SPI0_DOUT _GPIO(SPI0_DOUT)
+#define TZ1090_PIN_SPI0_DIN _GPIO(SPI0_DIN)
+#define TZ1090_PIN_SPI1_MCLK _GPIO(SPI1_MCLK)
+#define TZ1090_PIN_SPI1_CS0 _GPIO(SPI1_CS0)
+#define TZ1090_PIN_SPI1_CS1 _GPIO(SPI1_CS1)
+#define TZ1090_PIN_SPI1_CS2 _GPIO(SPI1_CS2)
+#define TZ1090_PIN_SPI1_DOUT _GPIO(SPI1_DOUT)
+#define TZ1090_PIN_SPI1_DIN _GPIO(SPI1_DIN)
+#define TZ1090_PIN_UART0_RXD _GPIO(UART0_RXD)
+#define TZ1090_PIN_UART0_TXD _GPIO(UART0_TXD)
+#define TZ1090_PIN_UART0_CTS _GPIO(UART0_CTS)
+#define TZ1090_PIN_UART0_RTS _GPIO(UART0_RTS)
+#define TZ1090_PIN_UART1_RXD _GPIO(UART1_RXD)
+#define TZ1090_PIN_UART1_TXD _GPIO(UART1_TXD)
+#define TZ1090_PIN_SCB0_SDAT _GPIO(SCB0_SDAT)
+#define TZ1090_PIN_SCB0_SCLK _GPIO(SCB0_SCLK)
+#define TZ1090_PIN_SCB1_SDAT _GPIO(SCB1_SDAT)
+#define TZ1090_PIN_SCB1_SCLK _GPIO(SCB1_SCLK)
+#define TZ1090_PIN_SCB2_SDAT _GPIO(SCB2_SDAT)
+#define TZ1090_PIN_SCB2_SCLK _GPIO(SCB2_SCLK)
+#define TZ1090_PIN_I2S_MCLK _GPIO(I2S_MCLK)
+#define TZ1090_PIN_I2S_BCLK_OUT _GPIO(I2S_BCLK_OUT)
+#define TZ1090_PIN_I2S_LRCLK_OUT _GPIO(I2S_LRCLK_OUT)
+#define TZ1090_PIN_I2S_DOUT0 _GPIO(I2S_DOUT0)
+#define TZ1090_PIN_I2S_DOUT1 _GPIO(I2S_DOUT1)
+#define TZ1090_PIN_I2S_DOUT2 _GPIO(I2S_DOUT2)
+#define TZ1090_PIN_I2S_DIN _GPIO(I2S_DIN)
+#define TZ1090_PIN_PDM_A _GPIO(PDM_A)
+#define TZ1090_PIN_PDM_B _GPIO(PDM_B)
+#define TZ1090_PIN_PDM_C _GPIO(PDM_C)
+#define TZ1090_PIN_PDM_D _GPIO(PDM_D)
+#define TZ1090_PIN_TFT_RED0 _GPIO(TFT_RED0)
+#define TZ1090_PIN_TFT_RED1 _GPIO(TFT_RED1)
+#define TZ1090_PIN_TFT_RED2 _GPIO(TFT_RED2)
+#define TZ1090_PIN_TFT_RED3 _GPIO(TFT_RED3)
+#define TZ1090_PIN_TFT_RED4 _GPIO(TFT_RED4)
+#define TZ1090_PIN_TFT_RED5 _GPIO(TFT_RED5)
+#define TZ1090_PIN_TFT_RED6 _GPIO(TFT_RED6)
+#define TZ1090_PIN_TFT_RED7 _GPIO(TFT_RED7)
+#define TZ1090_PIN_TFT_GREEN0 _GPIO(TFT_GREEN0)
+#define TZ1090_PIN_TFT_GREEN1 _GPIO(TFT_GREEN1)
+#define TZ1090_PIN_TFT_GREEN2 _GPIO(TFT_GREEN2)
+#define TZ1090_PIN_TFT_GREEN3 _GPIO(TFT_GREEN3)
+#define TZ1090_PIN_TFT_GREEN4 _GPIO(TFT_GREEN4)
+#define TZ1090_PIN_TFT_GREEN5 _GPIO(TFT_GREEN5)
+#define TZ1090_PIN_TFT_GREEN6 _GPIO(TFT_GREEN6)
+#define TZ1090_PIN_TFT_GREEN7 _GPIO(TFT_GREEN7)
+#define TZ1090_PIN_TFT_BLUE0 _GPIO(TFT_BLUE0)
+#define TZ1090_PIN_TFT_BLUE1 _GPIO(TFT_BLUE1)
+#define TZ1090_PIN_TFT_BLUE2 _GPIO(TFT_BLUE2)
+#define TZ1090_PIN_TFT_BLUE3 _GPIO(TFT_BLUE3)
+#define TZ1090_PIN_TFT_BLUE4 _GPIO(TFT_BLUE4)
+#define TZ1090_PIN_TFT_BLUE5 _GPIO(TFT_BLUE5)
+#define TZ1090_PIN_TFT_BLUE6 _GPIO(TFT_BLUE6)
+#define TZ1090_PIN_TFT_BLUE7 _GPIO(TFT_BLUE7)
+#define TZ1090_PIN_TFT_VDDEN_GD _GPIO(TFT_VDDEN_GD)
+#define TZ1090_PIN_TFT_PANELCLK _GPIO(TFT_PANELCLK)
+#define TZ1090_PIN_TFT_BLANK_LS _GPIO(TFT_BLANK_LS)
+#define TZ1090_PIN_TFT_VSYNC_NS _GPIO(TFT_VSYNC_NS)
+#define TZ1090_PIN_TFT_HSYNC_NR _GPIO(TFT_HSYNC_NR)
+#define TZ1090_PIN_TFT_VD12ACB _GPIO(TFT_VD12ACB)
+#define TZ1090_PIN_TFT_PWRSAVE _GPIO(TFT_PWRSAVE)
+#define TZ1090_PIN_TX_ON _GPIO(TX_ON)
+#define TZ1090_PIN_RX_ON _GPIO(RX_ON)
+#define TZ1090_PIN_PLL_ON _GPIO(PLL_ON)
+#define TZ1090_PIN_PA_ON _GPIO(PA_ON)
+#define TZ1090_PIN_RX_HP _GPIO(RX_HP)
+#define TZ1090_PIN_GAIN0 _GPIO(GAIN0)
+#define TZ1090_PIN_GAIN1 _GPIO(GAIN1)
+#define TZ1090_PIN_GAIN2 _GPIO(GAIN2)
+#define TZ1090_PIN_GAIN3 _GPIO(GAIN3)
+#define TZ1090_PIN_GAIN4 _GPIO(GAIN4)
+#define TZ1090_PIN_GAIN5 _GPIO(GAIN5)
+#define TZ1090_PIN_GAIN6 _GPIO(GAIN6)
+#define TZ1090_PIN_GAIN7 _GPIO(GAIN7)
+#define TZ1090_PIN_ANT_SEL0 _GPIO(ANT_SEL0)
+#define TZ1090_PIN_ANT_SEL1 _GPIO(ANT_SEL1)
+#define TZ1090_PIN_SDH_CLK_IN _GPIO(SDH_CLK_IN)
+
+/* Non-GPIO pins follow */
+#define NUM_GPIOS NR_BUILTIN_GPIO
+#define _PIN(offset) (NUM_GPIOS + (offset))
+
+#define TZ1090_PIN_TCK _PIN(0)
+#define TZ1090_PIN_TRST _PIN(1)
+#define TZ1090_PIN_TDI _PIN(2)
+#define TZ1090_PIN_TDO _PIN(3)
+#define TZ1090_PIN_TMS _PIN(4)
+#define TZ1090_PIN_CLK_OUT0 _PIN(5)
+#define TZ1090_PIN_CLK_OUT1 _PIN(6)
+
+/* Pin names */
+
+static const struct pinctrl_pin_desc tz1090_pins[] = {
+ /* Normal GPIOs */
+ PINCTRL_PIN(TZ1090_PIN_SDIO_CLK, "sdio_clk"),
+ PINCTRL_PIN(TZ1090_PIN_SDIO_CMD, "sdio_cmd"),
+ PINCTRL_PIN(TZ1090_PIN_SDIO_D0, "sdio_d0"),
+ PINCTRL_PIN(TZ1090_PIN_SDIO_D1, "sdio_d1"),
+ PINCTRL_PIN(TZ1090_PIN_SDIO_D2, "sdio_d2"),
+ PINCTRL_PIN(TZ1090_PIN_SDIO_D3, "sdio_d3"),
+ PINCTRL_PIN(TZ1090_PIN_SDH_CD, "sdh_cd"),
+ PINCTRL_PIN(TZ1090_PIN_SDH_WP, "sdh_wp"),
+ PINCTRL_PIN(TZ1090_PIN_SPI0_MCLK, "spi0_mclk"),
+ PINCTRL_PIN(TZ1090_PIN_SPI0_CS0, "spi0_cs0"),
+ PINCTRL_PIN(TZ1090_PIN_SPI0_CS1, "spi0_cs1"),
+ PINCTRL_PIN(TZ1090_PIN_SPI0_CS2, "spi0_cs2"),
+ PINCTRL_PIN(TZ1090_PIN_SPI0_DOUT, "spi0_dout"),
+ PINCTRL_PIN(TZ1090_PIN_SPI0_DIN, "spi0_din"),
+ PINCTRL_PIN(TZ1090_PIN_SPI1_MCLK, "spi1_mclk"),
+ PINCTRL_PIN(TZ1090_PIN_SPI1_CS0, "spi1_cs0"),
+ PINCTRL_PIN(TZ1090_PIN_SPI1_CS1, "spi1_cs1"),
+ PINCTRL_PIN(TZ1090_PIN_SPI1_CS2, "spi1_cs2"),
+ PINCTRL_PIN(TZ1090_PIN_SPI1_DOUT, "spi1_dout"),
+ PINCTRL_PIN(TZ1090_PIN_SPI1_DIN, "spi1_din"),
+ PINCTRL_PIN(TZ1090_PIN_UART0_RXD, "uart0_rxd"),
+ PINCTRL_PIN(TZ1090_PIN_UART0_TXD, "uart0_txd"),
+ PINCTRL_PIN(TZ1090_PIN_UART0_CTS, "uart0_cts"),
+ PINCTRL_PIN(TZ1090_PIN_UART0_RTS, "uart0_rts"),
+ PINCTRL_PIN(TZ1090_PIN_UART1_RXD, "uart1_rxd"),
+ PINCTRL_PIN(TZ1090_PIN_UART1_TXD, "uart1_txd"),
+ PINCTRL_PIN(TZ1090_PIN_SCB0_SDAT, "scb0_sdat"),
+ PINCTRL_PIN(TZ1090_PIN_SCB0_SCLK, "scb0_sclk"),
+ PINCTRL_PIN(TZ1090_PIN_SCB1_SDAT, "scb1_sdat"),
+ PINCTRL_PIN(TZ1090_PIN_SCB1_SCLK, "scb1_sclk"),
+ PINCTRL_PIN(TZ1090_PIN_SCB2_SDAT, "scb2_sdat"),
+ PINCTRL_PIN(TZ1090_PIN_SCB2_SCLK, "scb2_sclk"),
+ PINCTRL_PIN(TZ1090_PIN_I2S_MCLK, "i2s_mclk"),
+ PINCTRL_PIN(TZ1090_PIN_I2S_BCLK_OUT, "i2s_bclk_out"),
+ PINCTRL_PIN(TZ1090_PIN_I2S_LRCLK_OUT, "i2s_lrclk_out"),
+ PINCTRL_PIN(TZ1090_PIN_I2S_DOUT0, "i2s_dout0"),
+ PINCTRL_PIN(TZ1090_PIN_I2S_DOUT1, "i2s_dout1"),
+ PINCTRL_PIN(TZ1090_PIN_I2S_DOUT2, "i2s_dout2"),
+ PINCTRL_PIN(TZ1090_PIN_I2S_DIN, "i2s_din"),
+ PINCTRL_PIN(TZ1090_PIN_PDM_A, "pdm_a"),
+ PINCTRL_PIN(TZ1090_PIN_PDM_B, "pdm_b"),
+ PINCTRL_PIN(TZ1090_PIN_PDM_C, "pdm_c"),
+ PINCTRL_PIN(TZ1090_PIN_PDM_D, "pdm_d"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED0, "tft_red0"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED1, "tft_red1"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED2, "tft_red2"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED3, "tft_red3"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED4, "tft_red4"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED5, "tft_red5"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED6, "tft_red6"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_RED7, "tft_red7"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN0, "tft_green0"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN1, "tft_green1"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN2, "tft_green2"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN3, "tft_green3"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN4, "tft_green4"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN5, "tft_green5"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN6, "tft_green6"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_GREEN7, "tft_green7"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE0, "tft_blue0"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE1, "tft_blue1"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE2, "tft_blue2"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE3, "tft_blue3"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE4, "tft_blue4"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE5, "tft_blue5"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE6, "tft_blue6"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLUE7, "tft_blue7"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_VDDEN_GD, "tft_vdden_gd"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_PANELCLK, "tft_panelclk"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_BLANK_LS, "tft_blank_ls"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_VSYNC_NS, "tft_vsync_ns"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_HSYNC_NR, "tft_hsync_nr"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_VD12ACB, "tft_vd12acb"),
+ PINCTRL_PIN(TZ1090_PIN_TFT_PWRSAVE, "tft_pwrsave"),
+ PINCTRL_PIN(TZ1090_PIN_TX_ON, "tx_on"),
+ PINCTRL_PIN(TZ1090_PIN_RX_ON, "rx_on"),
+ PINCTRL_PIN(TZ1090_PIN_PLL_ON, "pll_on"),
+ PINCTRL_PIN(TZ1090_PIN_PA_ON, "pa_on"),
+ PINCTRL_PIN(TZ1090_PIN_RX_HP, "rx_hp"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN0, "gain0"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN1, "gain1"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN2, "gain2"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN3, "gain3"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN4, "gain4"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN5, "gain5"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN6, "gain6"),
+ PINCTRL_PIN(TZ1090_PIN_GAIN7, "gain7"),
+ PINCTRL_PIN(TZ1090_PIN_ANT_SEL0, "ant_sel0"),
+ PINCTRL_PIN(TZ1090_PIN_ANT_SEL1, "ant_sel1"),
+ PINCTRL_PIN(TZ1090_PIN_SDH_CLK_IN, "sdh_clk_in"),
+
+ /* Non-GPIOs */
+ PINCTRL_PIN(TZ1090_PIN_TCK, "tck"),
+ PINCTRL_PIN(TZ1090_PIN_TRST, "trst"),
+ PINCTRL_PIN(TZ1090_PIN_TDI, "tdi"),
+ PINCTRL_PIN(TZ1090_PIN_TDO, "tdo"),
+ PINCTRL_PIN(TZ1090_PIN_TMS, "tms"),
+ PINCTRL_PIN(TZ1090_PIN_CLK_OUT0, "clk_out0"),
+ PINCTRL_PIN(TZ1090_PIN_CLK_OUT1, "clk_out1"),
+};
+
+/* Pin group pins */
+
+static const unsigned spi1_cs2_pins[] = {
+ TZ1090_PIN_SPI1_CS2,
+};
+
+static const unsigned pdm_d_pins[] = {
+ TZ1090_PIN_PDM_D,
+};
+
+static const unsigned tft_pins[] = {
+ TZ1090_PIN_TFT_RED0,
+ TZ1090_PIN_TFT_RED1,
+ TZ1090_PIN_TFT_RED2,
+ TZ1090_PIN_TFT_RED3,
+ TZ1090_PIN_TFT_RED4,
+ TZ1090_PIN_TFT_RED5,
+ TZ1090_PIN_TFT_RED6,
+ TZ1090_PIN_TFT_RED7,
+ TZ1090_PIN_TFT_GREEN0,
+ TZ1090_PIN_TFT_GREEN1,
+ TZ1090_PIN_TFT_GREEN2,
+ TZ1090_PIN_TFT_GREEN3,
+ TZ1090_PIN_TFT_GREEN4,
+ TZ1090_PIN_TFT_GREEN5,
+ TZ1090_PIN_TFT_GREEN6,
+ TZ1090_PIN_TFT_GREEN7,
+ TZ1090_PIN_TFT_BLUE0,
+ TZ1090_PIN_TFT_BLUE1,
+ TZ1090_PIN_TFT_BLUE2,
+ TZ1090_PIN_TFT_BLUE3,
+ TZ1090_PIN_TFT_BLUE4,
+ TZ1090_PIN_TFT_BLUE5,
+ TZ1090_PIN_TFT_BLUE6,
+ TZ1090_PIN_TFT_BLUE7,
+ TZ1090_PIN_TFT_VDDEN_GD,
+ TZ1090_PIN_TFT_PANELCLK,
+ TZ1090_PIN_TFT_BLANK_LS,
+ TZ1090_PIN_TFT_VSYNC_NS,
+ TZ1090_PIN_TFT_HSYNC_NR,
+ TZ1090_PIN_TFT_VD12ACB,
+ TZ1090_PIN_TFT_PWRSAVE,
+};
+
+static const unsigned afe_pins[] = {
+ TZ1090_PIN_TX_ON,
+ TZ1090_PIN_RX_ON,
+ TZ1090_PIN_PLL_ON,
+ TZ1090_PIN_PA_ON,
+ TZ1090_PIN_RX_HP,
+ TZ1090_PIN_ANT_SEL0,
+ TZ1090_PIN_ANT_SEL1,
+ TZ1090_PIN_GAIN0,
+ TZ1090_PIN_GAIN1,
+ TZ1090_PIN_GAIN2,
+ TZ1090_PIN_GAIN3,
+ TZ1090_PIN_GAIN4,
+ TZ1090_PIN_GAIN5,
+ TZ1090_PIN_GAIN6,
+ TZ1090_PIN_GAIN7,
+};
+
+static const unsigned sdio_pins[] = {
+ TZ1090_PIN_SDIO_CLK,
+ TZ1090_PIN_SDIO_CMD,
+ TZ1090_PIN_SDIO_D0,
+ TZ1090_PIN_SDIO_D1,
+ TZ1090_PIN_SDIO_D2,
+ TZ1090_PIN_SDIO_D3,
+};
+
+static const unsigned sdh_pins[] = {
+ TZ1090_PIN_SDH_CD,
+ TZ1090_PIN_SDH_WP,
+ TZ1090_PIN_SDH_CLK_IN,
+};
+
+static const unsigned spi0_pins[] = {
+ TZ1090_PIN_SPI0_MCLK,
+ TZ1090_PIN_SPI0_CS0,
+ TZ1090_PIN_SPI0_CS1,
+ TZ1090_PIN_SPI0_CS2,
+ TZ1090_PIN_SPI0_DOUT,
+ TZ1090_PIN_SPI0_DIN,
+};
+
+static const unsigned spi1_pins[] = {
+ TZ1090_PIN_SPI1_MCLK,
+ TZ1090_PIN_SPI1_CS0,
+ TZ1090_PIN_SPI1_CS1,
+ TZ1090_PIN_SPI1_CS2,
+ TZ1090_PIN_SPI1_DOUT,
+ TZ1090_PIN_SPI1_DIN,
+};
+
+static const unsigned uart0_pins[] = {
+ TZ1090_PIN_UART0_RTS,
+ TZ1090_PIN_UART0_CTS,
+ TZ1090_PIN_UART0_TXD,
+ TZ1090_PIN_UART0_RXD,
+};
+
+static const unsigned uart1_pins[] = {
+ TZ1090_PIN_UART1_TXD,
+ TZ1090_PIN_UART1_RXD,
+};
+
+static const unsigned uart_pins[] = {
+ TZ1090_PIN_UART1_TXD,
+ TZ1090_PIN_UART1_RXD,
+ TZ1090_PIN_UART0_RTS,
+ TZ1090_PIN_UART0_CTS,
+ TZ1090_PIN_UART0_TXD,
+ TZ1090_PIN_UART0_RXD,
+};
+
+static const unsigned scb0_pins[] = {
+ TZ1090_PIN_SCB0_SDAT,
+ TZ1090_PIN_SCB0_SCLK,
+};
+
+static const unsigned scb1_pins[] = {
+ TZ1090_PIN_SCB1_SDAT,
+ TZ1090_PIN_SCB1_SCLK,
+};
+
+static const unsigned scb2_pins[] = {
+ TZ1090_PIN_SCB2_SDAT,
+ TZ1090_PIN_SCB2_SCLK,
+};
+
+static const unsigned i2s_pins[] = {
+ TZ1090_PIN_I2S_MCLK,
+ TZ1090_PIN_I2S_BCLK_OUT,
+ TZ1090_PIN_I2S_LRCLK_OUT,
+ TZ1090_PIN_I2S_DOUT0,
+ TZ1090_PIN_I2S_DOUT1,
+ TZ1090_PIN_I2S_DOUT2,
+ TZ1090_PIN_I2S_DIN,
+};
+
+static const unsigned jtag_pins[] = {
+ TZ1090_PIN_TCK,
+ TZ1090_PIN_TRST,
+ TZ1090_PIN_TDI,
+ TZ1090_PIN_TDO,
+ TZ1090_PIN_TMS,
+};
+
+/* Drive pin group pins */
+
+static const unsigned drive_tft_pins[] = {
+ TZ1090_PIN_TFT_RED0,
+ TZ1090_PIN_TFT_RED1,
+ TZ1090_PIN_TFT_RED2,
+ TZ1090_PIN_TFT_RED3,
+ TZ1090_PIN_TFT_RED4,
+ TZ1090_PIN_TFT_RED5,
+ TZ1090_PIN_TFT_RED6,
+ TZ1090_PIN_TFT_RED7,
+ TZ1090_PIN_TFT_GREEN0,
+ TZ1090_PIN_TFT_GREEN1,
+ TZ1090_PIN_TFT_GREEN2,
+ TZ1090_PIN_TFT_GREEN3,
+ TZ1090_PIN_TFT_GREEN4,
+ TZ1090_PIN_TFT_GREEN5,
+ TZ1090_PIN_TFT_GREEN6,
+ TZ1090_PIN_TFT_GREEN7,
+ TZ1090_PIN_TFT_BLUE0,
+ TZ1090_PIN_TFT_BLUE1,
+ TZ1090_PIN_TFT_BLUE2,
+ TZ1090_PIN_TFT_BLUE3,
+ TZ1090_PIN_TFT_BLUE4,
+ TZ1090_PIN_TFT_BLUE5,
+ TZ1090_PIN_TFT_BLUE6,
+ TZ1090_PIN_TFT_BLUE7,
+ TZ1090_PIN_TFT_VDDEN_GD,
+ TZ1090_PIN_TFT_PANELCLK,
+ TZ1090_PIN_TFT_BLANK_LS,
+ TZ1090_PIN_TFT_VSYNC_NS,
+ TZ1090_PIN_TFT_HSYNC_NR,
+ TZ1090_PIN_TFT_VD12ACB,
+ TZ1090_PIN_TFT_PWRSAVE,
+};
+
+static const unsigned drive_sdio_pins[] = {
+ TZ1090_PIN_SDIO_CLK,
+ TZ1090_PIN_SDIO_CMD,
+ TZ1090_PIN_SDIO_D0,
+ TZ1090_PIN_SDIO_D1,
+ TZ1090_PIN_SDIO_D2,
+ TZ1090_PIN_SDIO_D3,
+ TZ1090_PIN_SDH_WP,
+ TZ1090_PIN_SDH_CD,
+ TZ1090_PIN_SDH_CLK_IN,
+};
+
+static const unsigned drive_i2s_pins[] = {
+ TZ1090_PIN_CLK_OUT1,
+ TZ1090_PIN_I2S_DIN,
+ TZ1090_PIN_I2S_DOUT0,
+ TZ1090_PIN_I2S_DOUT1,
+ TZ1090_PIN_I2S_DOUT2,
+ TZ1090_PIN_I2S_LRCLK_OUT,
+ TZ1090_PIN_I2S_BCLK_OUT,
+ TZ1090_PIN_I2S_MCLK,
+};
+
+static const unsigned drive_scb0_pins[] = {
+ TZ1090_PIN_SCB0_SCLK,
+ TZ1090_PIN_SCB0_SDAT,
+ TZ1090_PIN_PDM_D,
+ TZ1090_PIN_PDM_C,
+};
+
+static const unsigned drive_pdm_pins[] = {
+ TZ1090_PIN_CLK_OUT0,
+ TZ1090_PIN_PDM_B,
+ TZ1090_PIN_PDM_A,
+};
+
+/* Mux functions */
+
+enum tz1090_mux {
+ /* internal placeholder */
+ TZ1090_MUX_NA = -1,
+ /* default function for an unmuxed pin */
+ TZ1090_MUX_DEFAULT,
+ /* SDH/SDIO mux */
+ TZ1090_MUX_SDH,
+ TZ1090_MUX_SDIO,
+ /* USB_VBUS muxes */
+ TZ1090_MUX_SPI1_CS2,
+ TZ1090_MUX_PDM_DAC,
+ TZ1090_MUX_USB_VBUS,
+ /* AFE mux */
+ TZ1090_MUX_AFE,
+ TZ1090_MUX_TS_OUT_0,
+ /* EXT_DAC mux */
+ TZ1090_MUX_DAC,
+ TZ1090_MUX_NOT_IQADC_STB,
+ TZ1090_MUX_IQDAC_STB,
+ /* TFT mux */
+ TZ1090_MUX_TFT,
+ TZ1090_MUX_EXT_DAC,
+ TZ1090_MUX_TS_OUT_1,
+ TZ1090_MUX_LCD_TRACE,
+ TZ1090_MUX_PHY_RINGOSC,
+};
+
+/* Pin groups a function can be muxed to */
+
+static const char * const default_groups[] = {
+ /* non-muxing convenient gpio pingroups */
+ "uart",
+ "uart0",
+ "uart1",
+ "spi0",
+ "spi1",
+ "scb0",
+ "scb1",
+ "scb2",
+ "i2s",
+ /* pingroups of individual pins without a (non gpio select) mux */
+ "sdio_clk",
+ "sdio_cmd",
+ "sdio_d0",
+ "sdio_d1",
+ "sdio_d2",
+ "sdio_d3",
+ "sdh_cd",
+ "sdh_wp",
+ "spi0_mclk",
+ "spi0_cs0",
+ "spi0_cs1",
+ "spi0_cs2",
+ "spi0_dout",
+ "spi0_din",
+ "spi1_mclk",
+ "spi1_cs0",
+ "spi1_cs1",
+ /* spi1_cs2 can be muxed individually */
+ "spi1_dout",
+ "spi1_din",
+ "uart0_rxd",
+ "uart0_txd",
+ "uart0_cts",
+ "uart0_rts",
+ "uart1_rxd",
+ "uart1_txd",
+ "scb0_sdat",
+ "scb0_sclk",
+ "scb1_sdat",
+ "scb1_sclk",
+ "scb2_sdat",
+ "scb2_sclk",
+ "i2s_mclk",
+ "i2s_bclk_out",
+ "i2s_lrclk_out",
+ "i2s_dout0",
+ "i2s_dout1",
+ "i2s_dout2",
+ "i2s_din",
+ "pdm_a",
+ "pdm_b",
+ "pdm_c",
+ /* pdm_d can be muxed individually */
+ "tft_red0",
+ "tft_red1",
+ "tft_red2",
+ "tft_red3",
+ "tft_red4",
+ "tft_red5",
+ "tft_red6",
+ "tft_red7",
+ "tft_green0",
+ "tft_green1",
+ "tft_green2",
+ "tft_green3",
+ "tft_green4",
+ "tft_green5",
+ "tft_green6",
+ "tft_green7",
+ "tft_blue0",
+ "tft_blue1",
+ "tft_blue2",
+ "tft_blue3",
+ "tft_blue4",
+ "tft_blue5",
+ "tft_blue6",
+ "tft_blue7",
+ "tft_vdden_gd",
+ "tft_panelclk",
+ "tft_blank_ls",
+ "tft_vsync_ns",
+ "tft_hsync_nr",
+ "tft_vd12acb",
+ "tft_pwrsave",
+ "tx_on",
+ "rx_on",
+ "pll_on",
+ "pa_on",
+ "rx_hp",
+ "gain0",
+ "gain1",
+ "gain2",
+ "gain3",
+ "gain4",
+ "gain5",
+ "gain6",
+ "gain7",
+ "ant_sel0",
+ "ant_sel1",
+ "sdh_clk_in",
+};
+
+static const char * const sdh_sdio_groups[] = {
+ "sdh",
+ "sdio",
+};
+
+static const char * const spi1_cs2_groups[] = {
+ "spi1_cs2",
+};
+
+static const char * const pdm_dac_groups[] = {
+ "pdm_d",
+};
+
+static const char * const usb_vbus_groups[] = {
+ "spi1_cs2",
+ "pdm_d",
+};
+
+static const char * const afe_groups[] = {
+ "afe",
+};
+
+static const char * const tft_groups[] = {
+ "tft",
+};
+
+#define FUNCTION(mux, fname, group) \
+ [(TZ1090_MUX_ ## mux)] = { \
+ .name = #fname, \
+ .groups = group##_groups, \
+ .ngroups = ARRAY_SIZE(group##_groups), \
+ }
+/* For intermediate functions with submuxes */
+#define NULL_FUNCTION(mux, fname) \
+ [(TZ1090_MUX_ ## mux)] = { \
+ .name = #fname, \
+ }
+
+/* Must correlate with enum tz1090_mux */
+static const struct tz1090_function tz1090_functions[] = {
+ /* MUX fn pingroups */
+ FUNCTION(DEFAULT, default, default),
+ FUNCTION(SDH, sdh, sdh_sdio),
+ FUNCTION(SDIO, sdio, sdh_sdio),
+ FUNCTION(SPI1_CS2, spi1_cs2, spi1_cs2),
+ FUNCTION(PDM_DAC, pdm_dac, pdm_dac),
+ FUNCTION(USB_VBUS, usb_vbus, usb_vbus),
+ FUNCTION(AFE, afe, afe),
+ FUNCTION(TS_OUT_0, ts_out_0, afe),
+ FUNCTION(DAC, ext_dac, tft),
+ FUNCTION(NOT_IQADC_STB, not_iqadc_stb, tft),
+ FUNCTION(IQDAC_STB, iqdac_stb, tft),
+ FUNCTION(TFT, tft, tft),
+ NULL_FUNCTION(EXT_DAC, _ext_dac),
+ FUNCTION(TS_OUT_1, ts_out_1, tft),
+ FUNCTION(LCD_TRACE, lcd_trace, tft),
+ FUNCTION(PHY_RINGOSC, phy_ringosc, tft),
+};
+
+/* Sub muxes */
+
+#define MUX(f0, f1, f2, f3, f4, mux_r, mux_b, mux_w) \
+ { \
+ .funcs = { \
+ TZ1090_MUX_ ## f0, \
+ TZ1090_MUX_ ## f1, \
+ TZ1090_MUX_ ## f2, \
+ TZ1090_MUX_ ## f3, \
+ TZ1090_MUX_ ## f4, \
+ }, \
+ .reg = (REG_PINCTRL_ ## mux_r), \
+ .bit = (mux_b), \
+ .width = (mux_w), \
+ }
+
+#define DEFINE_SUBMUX(mux, f0, f1, f2, f3, f4, mux_r, mux_b, mux_w) \
+ static struct tz1090_muxdesc mux ## _submux = \
+ MUX(f0, f1, f2, f3, f4, mux_r, mux_b, mux_w)
+
+#define SUBMUX(f, submux) [(TZ1090_MUX_ ## f)] = &(submux ## _submux)
+
+/* Pin group with mux control */
+#define MUX_PG(pg_name, f0, f1, f2, f3, f4, \
+ mux_r, mux_b, mux_w, slw_b) \
+ { \
+ .name = #pg_name, \
+ .pins = pg_name##_pins, \
+ .npins = ARRAY_SIZE(pg_name##_pins), \
+ .mux = MUX(f0, f1, f2, f3, f4, \
+ mux_r, mux_b, mux_w), \
+ .drv = ((slw_b) >= 0), \
+ .slw_bit = (slw_b), \
+ }
+
+#define SIMPLE_PG(pg_name) \
+ { \
+ .name = #pg_name, \
+ .pins = pg_name##_pins, \
+ .npins = ARRAY_SIZE(pg_name##_pins), \
+ }
+
+#define SIMPLE_DRV_PG(pg_name, slw_b) \
+ { \
+ .name = #pg_name, \
+ .pins = pg_name##_pins, \
+ .npins = ARRAY_SIZE(pg_name##_pins), \
+ .drv = 1, \
+ .slw_bit = (slw_b), \
+ }
+
+#define DRV_PG(pg_name, slw_b) \
+ { \
+ .name = "drive_"#pg_name, \
+ .pins = drive_##pg_name##_pins, \
+ .npins = ARRAY_SIZE(drive_##pg_name##_pins), \
+ .drv = 1, \
+ .slw_bit = (slw_b), \
+ }
+
+/* name f0, f1, f2, f3, f4, mux r/b/w */
+DEFINE_SUBMUX(ext_dac, DAC, NOT_IQADC_STB, IQDAC_STB, NA, NA, IF_CTL, 6, 2);
+
+static struct tz1090_muxdesc *tz1090_submux[] = {
+ SUBMUX(EXT_DAC, ext_dac),
+};
+
+static const struct tz1090_pingroup tz1090_groups[] = {
+ /* Muxing pin groups */
+ /* pg_name, f0, f1, f2, f3, f4, mux r/b/w, slw/schmitt/drv b */
+ MUX_PG(sdh, SDH, SDIO, NA, NA, NA, IF_CTL, 20, 2, -1),
+ MUX_PG(sdio, SDIO, SDH, NA, NA, NA, IF_CTL, 16, 2, -1),
+ MUX_PG(spi1_cs2, SPI1_CS2, USB_VBUS, NA, NA, NA, IF_CTL, 10, 2, -1),
+ MUX_PG(pdm_d, PDM_DAC, USB_VBUS, NA, NA, NA, IF_CTL, 8, 2, -1),
+ MUX_PG(afe, AFE, TS_OUT_0, NA, NA, NA, IF_CTL, 4, 2, 0 /* 0, 0 */),
+ MUX_PG(tft, TFT, EXT_DAC, TS_OUT_1, LCD_TRACE, PHY_RINGOSC, IF_CTL, 0, 3, 10 /* 10, 20 */),
+
+ /* Simple pin groups with drive control */
+ /* pg_name, slw/schmitt/drv b */
+ SIMPLE_DRV_PG(jtag, 11 /* 11, 22 */),
+ SIMPLE_DRV_PG(scb2, 9 /* 9, 18 */),
+ SIMPLE_DRV_PG(spi0, 7 /* 7, 14 */),
+ SIMPLE_DRV_PG(uart, 5 /* 5, 10 */),
+ SIMPLE_DRV_PG(scb1, 4 /* 4, 8 */),
+ SIMPLE_DRV_PG(spi1, 3 /* 3, 6 */),
+
+ /* Drive specific pin groups (drive_*) */
+ /* pg_name, slw/schmitt/drv b */
+ DRV_PG(sdio, 8 /* 8, 16 */), /* sdio_* + sdh_* */
+ DRV_PG(i2s, 6 /* 6, 12 */), /* i2s_* + clk_out1 */
+ DRV_PG(scb0, 2 /* 2, 4 */), /* scb0_* + pdm_{c,d} */
+ DRV_PG(pdm, 1 /* 1, 2 */), /* pdm_{a,b} + clk_out0 */
+
+ /* Convenience pin groups */
+ /* pg_name */
+ SIMPLE_PG(uart0),
+ SIMPLE_PG(uart1),
+ SIMPLE_PG(scb0),
+ SIMPLE_PG(i2s),
+
+ /* pseudo-pingroups for each GPIO pin follow */
+};
+
+/**
+ * struct tz1090_pmx - Private pinctrl data
+ * @dev: Platform device
+ * @pctl: Pin control device
+ * @regs: Register region
+ * @lock: Lock protecting coherency of pin_en, gpio_en, select_en, and
+ * SELECT regs
+ * @pin_en: Pins that have been enabled (32 pins packed into each element)
+ * @gpio_en: GPIOs that have been enabled (32 pins packed into each element)
+ * @select_en: Pins that have been force seleced by pinconf (32 pins packed
+ * into each element)
+ */
+struct tz1090_pmx {
+ struct device *dev;
+ struct pinctrl_dev *pctl;
+ void __iomem *regs;
+ spinlock_t lock;
+ u32 pin_en[3];
+ u32 gpio_en[3];
+ u32 select_en[3];
+};
+
+static inline u32 pmx_read(struct tz1090_pmx *pmx, u32 reg)
+{
+ return ioread32(pmx->regs + reg);
+}
+
+static inline void pmx_write(struct tz1090_pmx *pmx, u32 val, u32 reg)
+{
+ iowrite32(val, pmx->regs + reg);
+}
+
+/*
+ * Pin control operations
+ */
+
+/* each GPIO pin has it's own pseudo pingroup containing only itself */
+
+static int tz1090_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ return ARRAY_SIZE(tz1090_groups) + NUM_GPIOS;
+}
+
+static const char *tz1090_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned group)
+{
+ if (group < ARRAY_SIZE(tz1090_groups)) {
+ /* normal pingroup */
+ return tz1090_groups[group].name;
+ } else {
+ /* individual gpio pin pseudo-pingroup */
+ unsigned int pin = group - ARRAY_SIZE(tz1090_groups);
+ return tz1090_pins[pin].name;
+ }
+}
+
+static int tz1090_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned group,
+ const unsigned **pins,
+ unsigned *num_pins)
+{
+ if (group < ARRAY_SIZE(tz1090_groups)) {
+ /* normal pingroup */
+ *pins = tz1090_groups[group].pins;
+ *num_pins = tz1090_groups[group].npins;
+ } else {
+ /* individual gpio pin pseudo-pingroup */
+ unsigned int pin = group - ARRAY_SIZE(tz1090_groups);
+ *pins = &tz1090_pins[pin].number;
+ *num_pins = 1;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void tz1090_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s,
+ unsigned offset)
+{
+ seq_printf(s, " %s", dev_name(pctldev->dev));
+}
+#endif
+
+static int reserve_map(struct device *dev, struct pinctrl_map **map,
+ unsigned *reserved_maps, unsigned *num_maps,
+ unsigned reserve)
+{
+ unsigned old_num = *reserved_maps;
+ unsigned new_num = *num_maps + reserve;
+ struct pinctrl_map *new_map;
+
+ if (old_num >= new_num)
+ return 0;
+
+ new_map = krealloc(*map, sizeof(*new_map) * new_num, GFP_KERNEL);
+ if (!new_map) {
+ dev_err(dev, "krealloc(map) failed\n");
+ return -ENOMEM;
+ }
+
+ memset(new_map + old_num, 0, (new_num - old_num) * sizeof(*new_map));
+
+ *map = new_map;
+ *reserved_maps = new_num;
+
+ return 0;
+}
+
+static int add_map_mux(struct pinctrl_map **map, unsigned *reserved_maps,
+ unsigned *num_maps, const char *group,
+ const char *function)
+{
+ if (WARN_ON(*num_maps == *reserved_maps))
+ return -ENOSPC;
+
+ (*map)[*num_maps].type = PIN_MAP_TYPE_MUX_GROUP;
+ (*map)[*num_maps].data.mux.group = group;
+ (*map)[*num_maps].data.mux.function = function;
+ (*num_maps)++;
+
+ return 0;
+}
+
+static int add_map_configs(struct device *dev,
+ struct pinctrl_map **map,
+ unsigned *reserved_maps, unsigned *num_maps,
+ const char *group, unsigned long *configs,
+ unsigned num_configs)
+{
+ unsigned long *dup_configs;
+
+ if (WARN_ON(*num_maps == *reserved_maps))
+ return -ENOSPC;
+
+ dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs),
+ GFP_KERNEL);
+ if (!dup_configs) {
+ dev_err(dev, "kmemdup(configs) failed\n");
+ return -ENOMEM;
+ }
+
+ (*map)[*num_maps].type = PIN_MAP_TYPE_CONFIGS_GROUP;
+ (*map)[*num_maps].data.configs.group_or_pin = group;
+ (*map)[*num_maps].data.configs.configs = dup_configs;
+ (*map)[*num_maps].data.configs.num_configs = num_configs;
+ (*num_maps)++;
+
+ return 0;
+}
+
+static int add_config(struct device *dev, unsigned long **configs,
+ unsigned *num_configs, unsigned long config)
+{
+ unsigned old_num = *num_configs;
+ unsigned new_num = old_num + 1;
+ unsigned long *new_configs;
+
+ new_configs = krealloc(*configs, sizeof(*new_configs) * new_num,
+ GFP_KERNEL);
+ if (!new_configs) {
+ dev_err(dev, "krealloc(configs) failed\n");
+ return -ENOMEM;
+ }
+
+ new_configs[old_num] = config;
+
+ *configs = new_configs;
+ *num_configs = new_num;
+
+ return 0;
+}
+
+void tz1090_pinctrl_dt_free_map(struct pinctrl_dev *pctldev,
+ struct pinctrl_map *map, unsigned num_maps)
+{
+ int i;
+
+ for (i = 0; i < num_maps; i++)
+ if (map[i].type == PIN_MAP_TYPE_CONFIGS_GROUP)
+ kfree(map[i].data.configs.configs);
+
+ kfree(map);
+}
+
+static const struct cfg_param {
+ const char *property;
+ enum tz1090_pinconf_param param;
+} cfg_params[] = {
+ {"select", TZ1090_PINCONF_PARAM_SELECT},
+ {"pull", TZ1090_PINCONF_PARAM_PULL},
+ {"schmitt", TZ1090_PINCONF_PARAM_SCHMITT},
+ {"slew-rate", TZ1090_PINCONF_PARAM_SLEW_RATE},
+ {"drive-strength", TZ1090_PINCONF_PARAM_DRIVE_STRENGTH},
+};
+
+int tz1090_pinctrl_dt_subnode_to_map(struct device *dev,
+ struct device_node *np,
+ struct pinctrl_map **map,
+ unsigned *reserved_maps,
+ unsigned *num_maps)
+{
+ int ret, i;
+ const char *function;
+ u32 val;
+ unsigned long config;
+ unsigned long *configs = NULL;
+ unsigned num_configs = 0;
+ unsigned reserve;
+ struct property *prop;
+ const char *group;
+
+ ret = of_property_read_string(np, "function", &function);
+ if (ret < 0) {
+ /* EINVAL=missing, which is fine since it's optional */
+ if (ret != -EINVAL)
+ dev_err(dev, "could not parse property function\n");
+ function = NULL;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(cfg_params); i++) {
+ ret = of_property_read_u32(np, cfg_params[i].property, &val);
+ if (!ret) {
+ config = TZ1090_PINCONF_PACK(cfg_params[i].param, val);
+ ret = add_config(dev, &configs, &num_configs, config);
+ if (ret < 0)
+ goto exit;
+ /* EINVAL=missing, which is fine since it's optional */
+ } else if (ret != -EINVAL) {
+ dev_err(dev, "could not parse property %s\n",
+ cfg_params[i].property);
+ }
+ }
+
+ reserve = 0;
+ if (function != NULL)
+ reserve++;
+ if (num_configs)
+ reserve++;
+ ret = of_property_count_strings(np, "pins");
+ if (ret < 0) {
+ dev_err(dev, "could not parse property pins\n");
+ goto exit;
+ }
+ reserve *= ret;
+
+ ret = reserve_map(dev, map, reserved_maps, num_maps, reserve);
+ if (ret < 0)
+ goto exit;
+
+ of_property_for_each_string(np, "pins", prop, group) {
+ if (function) {
+ ret = add_map_mux(map, reserved_maps, num_maps,
+ group, function);
+ if (ret < 0)
+ goto exit;
+ }
+
+ if (num_configs) {
+ ret = add_map_configs(dev, map, reserved_maps,
+ num_maps, group, configs,
+ num_configs);
+ if (ret < 0)
+ goto exit;
+ }
+ }
+
+ ret = 0;
+
+exit:
+ kfree(configs);
+ return ret;
+}
+
+int tz1090_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np_config,
+ struct pinctrl_map **map, unsigned *num_maps)
+{
+ unsigned reserved_maps;
+ struct device_node *np;
+ int ret;
+
+ reserved_maps = 0;
+ *map = NULL;
+ *num_maps = 0;
+
+ for_each_child_of_node(np_config, np) {
+ ret = tz1090_pinctrl_dt_subnode_to_map(pctldev->dev, np, map,
+ &reserved_maps,
+ num_maps);
+ if (ret < 0) {
+ tz1090_pinctrl_dt_free_map(pctldev, *map, *num_maps);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static struct pinctrl_ops tz1090_pinctrl_ops = {
+ .get_groups_count = tz1090_pinctrl_get_groups_count,
+ .get_group_name = tz1090_pinctrl_get_group_name,
+ .get_group_pins = tz1090_pinctrl_get_group_pins,
+#ifdef CONFIG_DEBUG_FS
+ .pin_dbg_show = tz1090_pinctrl_pin_dbg_show,
+#endif
+ .dt_node_to_map = tz1090_pinctrl_dt_node_to_map,
+ .dt_free_map = tz1090_pinctrl_dt_free_map,
+};
+
+/*
+ * Pin mux operations
+ */
+
+static int tz1090_pinctrl_get_funcs_count(struct pinctrl_dev *pctldev)
+{
+ return ARRAY_SIZE(tz1090_functions);
+}
+
+static const char *tz1090_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
+ unsigned function)
+{
+ return tz1090_functions[function].name;
+}
+
+static int tz1090_pinctrl_get_func_groups(struct pinctrl_dev *pctldev,
+ unsigned function,
+ const char * const **groups,
+ unsigned * const num_groups)
+{
+ *groups = tz1090_functions[function].groups;
+ *num_groups = tz1090_functions[function].ngroups;
+
+ return 0;
+}
+
+/**
+ * tz1090_pinctrl_select() - update bit in SELECT register
+ * @pmx: Pinmux data
+ * @pin: Pin number (must be within GPIO range)
+ */
+static void tz1090_pinctrl_select(struct tz1090_pmx *pmx,
+ unsigned int pin)
+{
+ u32 reg, reg_shift, select, val;
+ unsigned int pmx_index, pmx_shift;
+ unsigned long flags;
+
+ /* uses base 32 instead of base 30 */
+ pmx_index = pin >> 5;
+ pmx_shift = pin & 0x1f;
+
+ /* select = !serial || gpio || force */
+ select = ((~pmx->pin_en[pmx_index] |
+ pmx->gpio_en[pmx_index] |
+ pmx->select_en[pmx_index]) >> pmx_shift) & 1;
+
+ /* find register and bit offset (base 30) */
+ reg = REG_PINCTRL_SELECT + 4*(pin / 30);
+ reg_shift = pin % 30;
+
+ /* modify gpio select bit */
+ __global_lock2(flags);
+ val = pmx_read(pmx, reg);
+ val &= ~(1 << reg_shift);
+ val |= select << reg_shift;
+ pmx_write(pmx, val, reg);
+ __global_unlock2(flags);
+}
+
+/**
+ * tz1090_pinctrl_gpio_select() - enable/disable GPIO usage for a pin
+ * @pmx: Pinmux data
+ * @pin: Pin number
+ * @gpio_select: 1 to enable pin as GPIO,
+ * 0 to leave control to whatever function is enabled
+ *
+ * Records that GPIO usage is enabled/disabled so that enabling a function
+ * doesn't override the SELECT register bit.
+ */
+static void tz1090_pinctrl_gpio_select(struct tz1090_pmx *pmx,
+ unsigned int pin,
+ unsigned int gpio_select)
+{
+ unsigned int index, shift;
+ u32 gpio_en;
+
+ if (pin >= NUM_GPIOS)
+ return;
+
+ /* uses base 32 instead of base 30 */
+ index = pin >> 5;
+ shift = pin & 0x1f;
+
+ spin_lock(&pmx->lock);
+
+ /* keep a record whether gpio is selected */
+ gpio_en = pmx->gpio_en[index];
+ gpio_en &= ~(1 << shift);
+ gpio_en |= (gpio_select << shift);
+ pmx->gpio_en[index] = gpio_en;
+
+ /* update the select bit */
+ tz1090_pinctrl_select(pmx, pin);
+
+ spin_unlock(&pmx->lock);
+}
+
+/**
+ * tz1090_pinctrl_serial_select() - enable/disable serial interface for a pin
+ * @pmx: Pinmux data
+ * @pin: Pin number
+ * @gpio_select: 1 to enable serial interface (devices) when not GPIO,
+ * 0 to leave pin in GPIO mode
+ *
+ * Records that serial usage is enabled/disabled so that SELECT register can be
+ * set appropriately when GPIO is disabled.
+ */
+static void tz1090_pinctrl_serial_select(struct tz1090_pmx *pmx,
+ unsigned int pin,
+ unsigned int serial_select)
+{
+ unsigned int index, shift;
+ u32 pin_en;
+
+ if (pin >= NUM_GPIOS)
+ return;
+
+ /* uses base 32 instead of base 30 */
+ index = pin >> 5;
+ shift = pin & 0x1f;
+
+ spin_lock(&pmx->lock);
+
+ /* keep a record whether serial is selected */
+ pin_en = pmx->pin_en[index];
+ pin_en &= ~(1 << shift);
+ pin_en |= (serial_select << shift);
+ pmx->pin_en[index] = pin_en;
+
+ /* update the select bit */
+ tz1090_pinctrl_select(pmx, pin);
+
+ spin_unlock(&pmx->lock);
+}
+
+/**
+ * tz1090_pinctrl_force_select() - enable/disable force gpio select for a pin
+ * @pmx: Pinmux data
+ * @pin: Pin number
+ * @gpio_select: 1 to force GPIO select,
+ * 0 to unforce GPIO select
+ *
+ * Records that the GPIO is force selected and serial interface shouldn't be
+ * enabled.
+ */
+static void tz1090_pinctrl_force_select(struct tz1090_pmx *pmx,
+ unsigned int pin,
+ unsigned int force_select)
+{
+ unsigned int index, shift;
+ u32 select_en;
+
+ if (pin >= NUM_GPIOS)
+ return;
+
+ /* uses base 32 instead of base 30 */
+ index = pin >> 5;
+ shift = pin & 0x1f;
+
+ spin_lock(&pmx->lock);
+
+ /* keep a record whether serial is selected */
+ select_en = pmx->select_en[index];
+ select_en &= ~(1 << shift);
+ select_en |= (force_select << shift);
+ pmx->select_en[index] = select_en;
+
+ /* update the select bit */
+ tz1090_pinctrl_select(pmx, pin);
+
+ spin_unlock(&pmx->lock);
+}
+
+static int tz1090_pinctrl_enable_mux(struct tz1090_pmx *pmx,
+ const struct tz1090_muxdesc *desc,
+ unsigned int function)
+{
+ const int *fit;
+ unsigned long flags;
+ int mux;
+ unsigned int func, ret;
+ u32 reg, mask;
+
+ /* find the mux value for this function, searching recursively */
+ for (mux = 0, fit = desc->funcs;
+ mux < ARRAY_SIZE(desc->funcs); ++mux, ++fit) {
+ func = *fit;
+ if (func == function)
+ goto found_mux;
+
+ /* maybe it's a sub-mux */
+ if (func < ARRAY_SIZE(tz1090_submux) && tz1090_submux[func]) {
+ ret = tz1090_pinctrl_enable_mux(pmx,
+ tz1090_submux[func],
+ function);
+ if (!ret)
+ goto found_mux;
+ }
+ }
+
+ return -EINVAL;
+found_mux:
+
+ /* Set up the mux */
+ if (desc->width) {
+ mask = ((1 << desc->width) - 1) << desc->bit;
+ __global_lock2(flags);
+ reg = pmx_read(pmx, desc->reg);
+ reg &= ~mask;
+ reg |= (mux << desc->bit) & mask;
+ pmx_write(pmx, reg, desc->reg);
+ __global_unlock2(flags);
+ }
+
+ return 0;
+}
+
+static int tz1090_pinctrl_enable(struct pinctrl_dev *pctldev, unsigned function,
+ unsigned group)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ const struct tz1090_pingroup *grp;
+ int ret;
+ const unsigned int *pit;
+ unsigned int i, pin;
+
+ if (group >= ARRAY_SIZE(tz1090_groups)) {
+ pin = group - ARRAY_SIZE(tz1090_groups);
+ dev_dbg(pctldev->dev, "%s(func=%u (%s), pin=%u (%s))\n",
+ __func__,
+ function, tz1090_functions[function].name,
+ pin,
+ tz1090_pins[pin].name);
+
+ /* no muxing necessary */
+ if (function != TZ1090_MUX_DEFAULT)
+ return -EINVAL;
+ tz1090_pinctrl_serial_select(pmx, pin, 1);
+ return 0;
+ }
+
+ grp = &tz1090_groups[group];
+ dev_dbg(pctldev->dev, "%s(func=%u (%s), group=%u (%s))\n",
+ __func__,
+ function, tz1090_functions[function].name,
+ group, grp->name);
+
+ ret = tz1090_pinctrl_enable_mux(pmx, &grp->mux, function);
+ if (ret)
+ return ret;
+
+ /* set up each pin in group to serial interface */
+ for (i = 0, pit = grp->pins; i < grp->npins; ++i, ++pit)
+ tz1090_pinctrl_serial_select(pmx, *pit, 1);
+
+ return 0;
+}
+
+static void tz1090_pinctrl_disable(struct pinctrl_dev *pctldev,
+ unsigned function, unsigned group)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ const struct tz1090_pingroup *grp;
+ const unsigned int *pit;
+ unsigned int i, pin;
+
+ if (group >= ARRAY_SIZE(tz1090_groups)) {
+ pin = group - ARRAY_SIZE(tz1090_groups);
+ dev_dbg(pctldev->dev, "%s(func=%u (%s), pin=%u (%s))\n",
+ __func__,
+ function, tz1090_functions[function].name,
+ pin,
+ tz1090_pins[pin].name);
+
+ tz1090_pinctrl_serial_select(pmx, pin, 0);
+ return;
+ }
+
+ grp = &tz1090_groups[group];
+ dev_dbg(pctldev->dev, "%s(func=%u (%s), group=%u (%s))\n",
+ __func__,
+ function, tz1090_functions[function].name,
+ group, grp->name);
+
+ /* set up each pin in group to serial interface */
+ for (i = 0, pit = grp->pins; i < grp->npins; ++i, ++pit)
+ tz1090_pinctrl_serial_select(pmx, *pit, 0);
+}
+
+static int tz1090_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ tz1090_pinctrl_gpio_select(pmx, pin, 1);
+ return 0;
+}
+
+static void tz1090_pinctrl_gpio_disable_free(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ tz1090_pinctrl_gpio_select(pmx, pin, 0);
+}
+
+static struct pinmux_ops tz1090_pinmux_ops = {
+ .get_functions_count = tz1090_pinctrl_get_funcs_count,
+ .get_function_name = tz1090_pinctrl_get_func_name,
+ .get_function_groups = tz1090_pinctrl_get_func_groups,
+ .enable = tz1090_pinctrl_enable,
+ .disable = tz1090_pinctrl_disable,
+ .gpio_request_enable = tz1090_pinctrl_gpio_request_enable,
+ .gpio_disable_free = tz1090_pinctrl_gpio_disable_free,
+};
+
+/*
+ * Pin config operations
+ */
+
+struct tz1090_pinconf_pullup {
+ unsigned char index;
+ unsigned char shift;
+};
+
+/* The mapping of pin to pull up/down register index and shift */
+static struct tz1090_pinconf_pullup tz1090_pinconf_pullup[] = {
+ {5, 22}, /* 0 - TZ1090_PIN_SDIO_CLK */
+ {0, 14}, /* 1 - TZ1090_PIN_SDIO_CMD */
+ {0, 6}, /* 2 - TZ1090_PIN_SDIO_D0 */
+ {0, 8}, /* 3 - TZ1090_PIN_SDIO_D1 */
+ {0, 10}, /* 4 - TZ1090_PIN_SDIO_D2 */
+ {0, 12}, /* 5 - TZ1090_PIN_SDIO_D3 */
+ {0, 2}, /* 6 - TZ1090_PIN_SDH_CD */
+ {0, 4}, /* 7 - TZ1090_PIN_SDH_WP */
+ {0, 16}, /* 8 - TZ1090_PIN_SPI0_MCLK */
+ {0, 18}, /* 9 - TZ1090_PIN_SPI0_CS0 */
+ {0, 20}, /* 10 - TZ1090_PIN_SPI0_CS1 */
+ {0, 22}, /* 11 - TZ1090_PIN_SPI0_CS2 */
+ {0, 24}, /* 12 - TZ1090_PIN_SPI0_DOUT */
+ {0, 26}, /* 13 - TZ1090_PIN_SPI0_DIN */
+ {0, 28}, /* 14 - TZ1090_PIN_SPI1_MCLK */
+ {0, 30}, /* 15 - TZ1090_PIN_SPI1_CS0 */
+ {1, 0}, /* 16 - TZ1090_PIN_SPI1_CS1 */
+ {1, 2}, /* 17 - TZ1090_PIN_SPI1_CS2 */
+ {1, 4}, /* 18 - TZ1090_PIN_SPI1_DOUT */
+ {1, 6}, /* 19 - TZ1090_PIN_SPI1_DIN */
+ {1, 8}, /* 20 - TZ1090_PIN_UART0_RXD */
+ {1, 10}, /* 21 - TZ1090_PIN_UART0_TXD */
+ {1, 12}, /* 22 - TZ1090_PIN_UART0_CTS */
+ {1, 14}, /* 23 - TZ1090_PIN_UART0_RTS */
+ {1, 16}, /* 24 - TZ1090_PIN_UART1_RXD */
+ {1, 18}, /* 25 - TZ1090_PIN_UART1_TXD */
+ {1, 20}, /* 26 - TZ1090_PIN_SCB0_SDAT */
+ {1, 22}, /* 27 - TZ1090_PIN_SCB0_SCLK */
+ {1, 24}, /* 28 - TZ1090_PIN_SCB1_SDAT */
+ {1, 26}, /* 29 - TZ1090_PIN_SCB1_SCLK */
+
+ {1, 28}, /* 30 - TZ1090_PIN_SCB2_SDAT */
+ {1, 29}, /* 31 - TZ1090_PIN_SCB2_SCLK */
+ {2, 0}, /* 32 - TZ1090_PIN_I2S_MCLK */
+ {2, 2}, /* 33 - TZ1090_PIN_I2S_BCLK_OUT */
+ {2, 4}, /* 34 - TZ1090_PIN_I2S_LRCLK_OUT */
+ {2, 6}, /* 35 - TZ1090_PIN_I2S_DOUT0 */
+ {2, 8}, /* 36 - TZ1090_PIN_I2S_DOUT1 */
+ {2, 10}, /* 37 - TZ1090_PIN_I2S_DOUT2 */
+ {2, 12}, /* 38 - TZ1090_PIN_I2S_DIN */
+ {4, 12}, /* 39 - TZ1090_PIN_PDM_A */
+ {4, 14}, /* 40 - TZ1090_PIN_PDM_B */
+ {4, 18}, /* 41 - TZ1090_PIN_PDM_C */
+ {4, 20}, /* 42 - TZ1090_PIN_PDM_D */
+ {2, 14}, /* 43 - TZ1090_PIN_TFT_RED0 */
+ {2, 16}, /* 44 - TZ1090_PIN_TFT_RED1 */
+ {2, 18}, /* 45 - TZ1090_PIN_TFT_RED2 */
+ {2, 20}, /* 46 - TZ1090_PIN_TFT_RED3 */
+ {2, 22}, /* 47 - TZ1090_PIN_TFT_RED4 */
+ {2, 24}, /* 48 - TZ1090_PIN_TFT_RED5 */
+ {2, 26}, /* 49 - TZ1090_PIN_TFT_RED6 */
+ {2, 28}, /* 50 - TZ1090_PIN_TFT_RED7 */
+ {2, 30}, /* 51 - TZ1090_PIN_TFT_GREEN0 */
+ {3, 0}, /* 52 - TZ1090_PIN_TFT_GREEN1 */
+ {3, 2}, /* 53 - TZ1090_PIN_TFT_GREEN2 */
+ {3, 4}, /* 54 - TZ1090_PIN_TFT_GREEN3 */
+ {3, 6}, /* 55 - TZ1090_PIN_TFT_GREEN4 */
+ {3, 8}, /* 56 - TZ1090_PIN_TFT_GREEN5 */
+ {3, 10}, /* 57 - TZ1090_PIN_TFT_GREEN6 */
+ {3, 12}, /* 58 - TZ1090_PIN_TFT_GREEN7 */
+ {3, 14}, /* 59 - TZ1090_PIN_TFT_BLUE0 */
+
+ {3, 16}, /* 60 - TZ1090_PIN_TFT_BLUE1 */
+ {3, 18}, /* 61 - TZ1090_PIN_TFT_BLUE2 */
+ {3, 20}, /* 62 - TZ1090_PIN_TFT_BLUE3 */
+ {3, 22}, /* 63 - TZ1090_PIN_TFT_BLUE4 */
+ {3, 24}, /* 64 - TZ1090_PIN_TFT_BLUE5 */
+ {3, 26}, /* 65 - TZ1090_PIN_TFT_BLUE6 */
+ {3, 28}, /* 66 - TZ1090_PIN_TFT_BLUE7 */
+ {3, 30}, /* 67 - TZ1090_PIN_TFT_VDDEN_GD */
+ {4, 0}, /* 68 - TZ1090_PIN_TFT_PANELCLK */
+ {4, 2}, /* 69 - TZ1090_PIN_TFT_BLANK_LS */
+ {4, 4}, /* 70 - TZ1090_PIN_TFT_VSYNC_NS */
+ {4, 6}, /* 71 - TZ1090_PIN_TFT_HSYNC_NR */
+ {4, 8}, /* 72 - TZ1090_PIN_TFT_VD12ACB */
+ {4, 10}, /* 73 - TZ1090_PIN_TFT_PWRSAVE */
+ {4, 24}, /* 74 - TZ1090_PIN_TX_ON */
+ {4, 26}, /* 75 - TZ1090_PIN_RX_ON */
+ {4, 28}, /* 76 - TZ1090_PIN_PLL_ON */
+ {4, 30}, /* 77 - TZ1090_PIN_PA_ON */
+ {5, 0}, /* 78 - TZ1090_PIN_RX_HP */
+ {5, 6}, /* 79 - TZ1090_PIN_GAIN0 */
+ {5, 8}, /* 80 - TZ1090_PIN_GAIN1 */
+ {5, 10}, /* 81 - TZ1090_PIN_GAIN2 */
+ {5, 12}, /* 82 - TZ1090_PIN_GAIN3 */
+ {5, 14}, /* 83 - TZ1090_PIN_GAIN4 */
+ {5, 16}, /* 84 - TZ1090_PIN_GAIN5 */
+ {5, 18}, /* 85 - TZ1090_PIN_GAIN6 */
+ {5, 20}, /* 86 - TZ1090_PIN_GAIN7 */
+ {5, 2}, /* 87 - TZ1090_PIN_ANT_SEL0 */
+ {5, 4}, /* 88 - TZ1090_PIN_ANT_SEL1 */
+ {0, 0}, /* 89 - TZ1090_PIN_SDH_CLK_IN */
+};
+
+static int tz1090_pinconf_reg(struct pinctrl_dev *pctldev,
+ unsigned int pin,
+ enum tz1090_pinconf_param param,
+ bool report_err,
+ u32 *reg, u32 *width, u32 *mask, u32 *shift)
+{
+ struct tz1090_pinconf_pullup *pu;
+
+ /* Only core GPIO'able pins */
+ if (pin >= NUM_GPIOS)
+ return -EINVAL;
+
+ /* Find information about parameter's register */
+ switch (param) {
+ case TZ1090_PINCONF_PARAM_SELECT:
+ *reg = REG_PINCTRL_SELECT + 4*(pin / 30);
+ *shift = pin % 30;
+ *width = 1;
+ break;
+ case TZ1090_PINCONF_PARAM_PULL:
+ pu = &tz1090_pinconf_pullup[pin];
+ *reg = REG_PINCTRL_PU_PD + 4*pu->index;
+ *shift = pu->shift;
+ *width = 2;
+ break;
+ default:
+ return -EINVAL;
+ };
+
+ /* Calculate field information */
+ *mask = ((1 << *width) - 1) << *shift;
+
+ return 0;
+}
+
+static int tz1090_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned pin, unsigned long *config)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ enum tz1090_pinconf_param param = TZ1090_PINCONF_UNPACK_PARAM(*config);
+ int ret;
+ u32 reg, width, mask, shift, val, arg;
+
+ /* Get register information */
+ ret = tz1090_pinconf_reg(pctldev, pin, param, true,
+ ®, &width, &mask, &shift);
+ if (ret < 0)
+ return ret;
+
+ /* Extract field from register */
+ val = pmx_read(pmx, reg);
+ arg = (val & mask) >> shift;
+
+ /* And pack config */
+ *config = TZ1090_PINCONF_PACK(param, arg);
+
+ return 0;
+}
+
+static int tz1090_pinconf_set(struct pinctrl_dev *pctldev,
+ unsigned pin, unsigned long config)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ enum tz1090_pinconf_param param = TZ1090_PINCONF_UNPACK_PARAM(config);
+ unsigned int arg = TZ1090_PINCONF_UNPACK_ARG(config);
+ int ret;
+ u32 reg, width, mask, shift, val;
+ unsigned long flags;
+
+ dev_dbg(pctldev->dev, "%s(pin=%s, config=%#lx)\n",
+ __func__, tz1090_pins[pin].name, config);
+
+ /* Select is a special case for writing */
+ if (param == TZ1090_PINCONF_PARAM_SELECT) {
+ if (arg > 1) {
+ dev_dbg(pctldev->dev, "%s: select larger than 1\n",
+ __func__);
+ return -EINVAL;
+ }
+ tz1090_pinctrl_force_select(pmx, pin, arg);
+ return 0;
+ }
+
+ /* Get register information */
+ ret = tz1090_pinconf_reg(pctldev, pin, param, true,
+ ®, &width, &mask, &shift);
+ if (ret < 0)
+ return ret;
+
+ /* Unpack argument and range check it */
+ if (arg >= (1 << width)) {
+ dev_dbg(pctldev->dev, "%s: arg %u larger than %u bits\n",
+ __func__, arg, width);
+ return -EINVAL;
+ }
+
+ /* Write register field */
+ __global_lock2(flags);
+ val = pmx_read(pmx, reg);
+ val &= ~mask;
+ val |= arg << shift;
+ pmx_write(pmx, val, reg);
+ __global_unlock2(flags);
+
+ return 0;
+}
+
+static int tz1090_pinconf_group_reg(struct pinctrl_dev *pctldev,
+ const struct tz1090_pingroup *g,
+ enum tz1090_pinconf_param param,
+ bool report_err,
+ u32 *reg, u32 *width, u32 *mask, u32 *shift)
+{
+ /* Drive configuration applies in groups, but not to all groups. */
+ if (!g->drv) {
+ if (report_err)
+ dev_dbg(pctldev->dev,
+ "%s: group %s has no drive control\n",
+ __func__, g->name);
+ return -EINVAL;
+ }
+
+ /* Find information about drive parameter's register */
+ switch (param) {
+ case TZ1090_PINCONF_PARAM_SCHMITT:
+ *reg = REG_PINCTRL_SCHMITT;
+ *width = 1;
+ break;
+ case TZ1090_PINCONF_PARAM_SLEW_RATE:
+ *reg = REG_PINCTRL_SR;
+ *width = 1;
+ break;
+ case TZ1090_PINCONF_PARAM_DRIVE_STRENGTH:
+ *reg = REG_PINCTRL_DR;
+ *width = 2;
+ break;
+ default:
+ return -EINVAL;
+ };
+
+ /* Calculate field information */
+ *shift = g->slw_bit * *width;
+ *mask = ((1 << *width) - 1) << *shift;
+
+ return 0;
+}
+
+static int tz1090_pinconf_group_get(struct pinctrl_dev *pctldev,
+ unsigned group,
+ unsigned long *config)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ const struct tz1090_pingroup *g;
+ enum tz1090_pinconf_param param = TZ1090_PINCONF_UNPACK_PARAM(*config);
+ int ret;
+ unsigned int pin;
+ u32 reg, width, mask, shift, val, arg;
+
+ if (group >= ARRAY_SIZE(tz1090_groups)) {
+ pin = group - ARRAY_SIZE(tz1090_groups);
+ return tz1090_pinconf_get(pctldev, pin, config);
+ }
+
+ g = &tz1090_groups[group];
+
+ /* We can't really get a per-pin configuration of a group. */
+ if (param < TZ1090_PINCONF_PARAM_GROUPED) {
+ dev_dbg(pctldev->dev,
+ "%s: Can't get per-pin param %u of group %s\n",
+ __func__, param, g->name);
+ return -EINVAL;
+ }
+
+ /* Get register information */
+ ret = tz1090_pinconf_group_reg(pctldev, g, param, true,
+ ®, &width, &mask, &shift);
+ if (ret < 0)
+ return ret;
+
+ /* Extract field from register */
+ val = pmx_read(pmx, reg);
+ arg = (val & mask) >> shift;
+
+ /* And pack config */
+ *config = TZ1090_PINCONF_PACK(param, arg);
+
+ return 0;
+}
+
+static int tz1090_pinconf_group_set(struct pinctrl_dev *pctldev,
+ unsigned group, unsigned long config)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ const struct tz1090_pingroup *g;
+ enum tz1090_pinconf_param param = TZ1090_PINCONF_UNPACK_PARAM(config);
+ unsigned int arg, pin, i;
+ const unsigned int *pit;
+ int ret;
+ u32 reg, width, mask, shift, val;
+ unsigned long flags;
+
+ if (group >= ARRAY_SIZE(tz1090_groups)) {
+ pin = group - ARRAY_SIZE(tz1090_groups);
+ return tz1090_pinconf_set(pctldev, pin, config);
+ }
+
+ g = &tz1090_groups[group];
+ dev_dbg(pctldev->dev, "%s(group=%s, config=%#lx)\n",
+ __func__, g->name, config);
+
+ /*
+ * If we're trying to set a per-pin configuration of a group, do the
+ * pins one by one. This is mainly as a convenience.
+ */
+ if (param < TZ1090_PINCONF_PARAM_GROUPED) {
+ for (i = 0, pit = g->pins; i < g->npins; ++i, ++pit) {
+ ret = tz1090_pinconf_set(pctldev, *pit, config);
+ if (ret)
+ return ret;
+ }
+ return 0;
+ }
+
+ /* Get register information */
+ ret = tz1090_pinconf_group_reg(pctldev, g, param, true,
+ ®, &width, &mask, &shift);
+ if (ret < 0)
+ return ret;
+
+ /* Unpack argument and range check it */
+ arg = TZ1090_PINCONF_UNPACK_ARG(config);
+ if (arg >= (1 << width)) {
+ dev_dbg(pctldev->dev, "%s: arg %u larger than %u bits\n",
+ __func__, arg, width);
+ return -EINVAL;
+ }
+
+ /* Write register field */
+ __global_lock2(flags);
+ val = pmx_read(pmx, reg);
+ val &= ~mask;
+ val |= arg << shift;
+ pmx_write(pmx, val, reg);
+ __global_unlock2(flags);
+
+ return 0;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void tz1090_pinconf_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned pin)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ int i, ret;
+ u32 reg, width, mask, shift, val;
+
+ for (i = 0; i < ARRAY_SIZE(cfg_params); i++) {
+ /* Get register information */
+ ret = tz1090_pinconf_reg(pctldev, pin, cfg_params[i].param,
+ false, ®, &width, &mask, &shift);
+ if (ret < 0)
+ continue;
+
+ /* Extract field from register */
+ val = pmx_read(pmx, reg);
+ val = (val & mask) >> shift;
+
+ seq_printf(s, "\n\t%s=%u",
+ cfg_params[i].property, val);
+ }
+}
+
+static const char *strip_prefix(const char *s)
+{
+ const char *comma = strchr(s, ',');
+ if (!comma)
+ return s;
+
+ return comma + 1;
+}
+
+static void tz1090_pinconf_group_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned group)
+{
+ struct tz1090_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
+ const struct tz1090_pingroup *g;
+ int i, ret;
+ u32 reg, width, mask, shift, val;
+
+ /* don't show pin configs in group dbg */
+ if (group >= ARRAY_SIZE(tz1090_groups))
+ return;
+
+ g = &tz1090_groups[group];
+ for (i = 0; i < ARRAY_SIZE(cfg_params); i++) {
+ /* Get register information */
+ ret = tz1090_pinconf_group_reg(pctldev, g, cfg_params[i].param,
+ false, ®, &width, &mask,
+ &shift);
+ if (ret < 0)
+ continue;
+
+ /* Extract field from register */
+ val = pmx_read(pmx, reg);
+ val = (val & mask) >> shift;
+
+ seq_printf(s, "\n\t%s=%u",
+ strip_prefix(cfg_params[i].property), val);
+ }
+}
+
+static void tz1090_pinconf_config_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s,
+ unsigned long config)
+{
+ enum tz1090_pinconf_param param = TZ1090_PINCONF_UNPACK_PARAM(config);
+ u16 arg = TZ1090_PINCONF_UNPACK_ARG(config);
+ const char *pname = "unknown";
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(cfg_params); i++) {
+ if (cfg_params[i].param == param) {
+ pname = cfg_params[i].property;
+ break;
+ }
+ }
+
+ seq_printf(s, "%s=%d", strip_prefix(pname), arg);
+}
+#endif
+
+struct pinconf_ops tz1090_pinconf_ops = {
+ .pin_config_get = tz1090_pinconf_get,
+ .pin_config_set = tz1090_pinconf_set,
+ .pin_config_group_get = tz1090_pinconf_group_get,
+ .pin_config_group_set = tz1090_pinconf_group_set,
+#ifdef CONFIG_DEBUG_FS
+ .pin_config_dbg_show = tz1090_pinconf_dbg_show,
+ .pin_config_group_dbg_show = tz1090_pinconf_group_dbg_show,
+ .pin_config_config_dbg_show = tz1090_pinconf_config_dbg_show,
+#endif
+};
+
+/*
+ * Pin control driver setup
+ */
+
+static struct pinctrl_desc tz1090_pinctrl_desc = {
+ .pctlops = &tz1090_pinctrl_ops,
+ .pmxops = &tz1090_pinmux_ops,
+ .confops = &tz1090_pinconf_ops,
+ .owner = THIS_MODULE,
+};
+
+static struct pinctrl_gpio_range tz1090_pinctrl_gpio_range = {
+ .name = "TZ1090 GPIOs",
+ .base = GPIO_0_BASE,
+ .npins = NUM_GPIOS,
+};
+
+static int tz1090_pinctrl_probe(struct platform_device *pdev)
+{
+ struct tz1090_pmx *pmx;
+ struct resource *res;
+
+ pmx = devm_kzalloc(&pdev->dev, sizeof(*pmx), GFP_KERNEL);
+ if (!pmx) {
+ dev_err(&pdev->dev, "Can't alloc tz1090_pmx\n");
+ return -ENOMEM;
+ }
+ pmx->dev = &pdev->dev;
+ spin_lock_init(&pmx->lock);
+
+ tz1090_pinctrl_desc.name = dev_name(&pdev->dev);
+ tz1090_pinctrl_desc.pins = tz1090_pins;
+ tz1090_pinctrl_desc.npins = ARRAY_SIZE(tz1090_pins);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Missing MEM resource\n");
+ return -ENODEV;
+ }
+
+ if (!devm_request_mem_region(&pdev->dev, res->start,
+ resource_size(res),
+ dev_name(&pdev->dev))) {
+ dev_err(&pdev->dev,
+ "Couldn't request MEM resource\n");
+ return -ENODEV;
+ }
+
+ pmx->regs = devm_ioremap(&pdev->dev, res->start,
+ resource_size(res));
+ if (!pmx->regs) {
+ dev_err(&pdev->dev, "Couldn't ioremap regs\n");
+ return -ENODEV;
+ }
+
+ pmx->pctl = pinctrl_register(&tz1090_pinctrl_desc, &pdev->dev, pmx);
+ if (!pmx->pctl) {
+ dev_err(&pdev->dev, "Couldn't register pinctrl driver\n");
+ return -ENODEV;
+ }
+
+ pinctrl_add_gpio_range(pmx->pctl, &tz1090_pinctrl_gpio_range);
+
+ platform_set_drvdata(pdev, pmx);
+
+ dev_info(&pdev->dev, "TZ1090 pinctrl driver initialised\n");
+
+ return 0;
+}
+
+static int tz1090_pinctrl_remove(struct platform_device *pdev)
+{
+ struct tz1090_pmx *pmx = platform_get_drvdata(pdev);
+
+ pinctrl_unregister(pmx->pctl);
+
+ return 0;
+}
+
+static struct of_device_id tz1090_pinctrl_of_match[] = {
+ { .compatible = "img,tz1090-pinctrl", },
+ { },
+};
+
+static struct platform_driver tz1090_pinctrl_driver = {
+ .driver = {
+ .name = "tz1090-pinctrl",
+ .owner = THIS_MODULE,
+ .of_match_table = tz1090_pinctrl_of_match,
+ },
+ .probe = tz1090_pinctrl_probe,
+ .remove = tz1090_pinctrl_remove,
+};
+
+static int __init tz1090_pinctrl_init(void)
+{
+ return platform_driver_register(&tz1090_pinctrl_driver);
+}
+postcore_initcall(tz1090_pinctrl_init);
+
+static void __exit tz1090_pinctrl_exit(void)
+{
+ platform_driver_unregister(&tz1090_pinctrl_driver);
+}
+module_exit(tz1090_pinctrl_exit);
+
+MODULE_AUTHOR("Imagination Technologies Ltd.");
+MODULE_DESCRIPTION("Toumaz Xenif TZ1090 pinctrl driver");
+MODULE_LICENSE("GPL v2");
+MODULE_DEVICE_TABLE(of, tz1090_pinctrl_of_match);
diff --git a/drivers/pinctrl/pinctrl-tz1090.h b/drivers/pinctrl/pinctrl-tz1090.h
new file mode 100644
index 0000000..b2553b0
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-tz1090.h
@@ -0,0 +1,58 @@
+#ifndef __PINCTRL_TZ1090_H__
+#define __PINCTRL_TZ1090_H__
+
+enum tz1090_pinconf_param {
+ /* per-gpio parameters */
+ TZ1090_PINCONF_PARAM_PERGPIO = 0,
+
+ /* argument: tz1090_pinconf_select */
+ TZ1090_PINCONF_PARAM_SELECT,
+ /* argument: tz1090_pinconf_pull */
+ TZ1090_PINCONF_PARAM_PULL,
+
+
+ /* grouped drive parameters */
+ TZ1090_PINCONF_PARAM_GROUPED,
+
+ /* argument: tz1090_pinconf_schmitt */
+ TZ1090_PINCONF_PARAM_SCHMITT,
+ /* argument: tz1090_pinconf_slew */
+ TZ1090_PINCONF_PARAM_SLEW_RATE,
+ /* argument: tz1090_pinconf_drive */
+ TZ1090_PINCONF_PARAM_DRIVE_STRENGTH,
+};
+
+enum tz1090_pinconf_select {
+ TZ1090_PINCONF_SELECT_SERIAL,
+ TZ1090_PINCONF_SELECT_GPIO,
+};
+
+enum tz1090_pinconf_pull {
+ TZ1090_PINCONF_PULL_TRISTATE,
+ TZ1090_PINCONF_PULL_UP,
+ TZ1090_PINCONF_PULL_DOWN,
+ TZ1090_PINCONF_PULL_REPEATER,
+};
+
+enum tz1090_pinconf_schmitt {
+ TZ1090_PINCONF_SCHMITT_OFF, /* no hysteresis */
+ TZ1090_PINCONF_SCHMITT_ON, /* schmitt trigger */
+};
+
+enum tz1090_pinconf_slew {
+ TZ1090_PINCONF_SLEW_SLOW, /* half frequency */
+ TZ1090_PINCONF_SLEW_FAST,
+};
+
+enum tz1090_pinconf_drive {
+ TZ1090_PINCONF_DRIVE_2mA,
+ TZ1090_PINCONF_DRIVE_4mA,
+ TZ1090_PINCONF_DRIVE_8mA,
+ TZ1090_PINCONF_DRIVE_12mA,
+};
+
+#define TZ1090_PINCONF_PACK(_param_, _arg_) ((_param_) << 16 | (_arg_))
+#define TZ1090_PINCONF_UNPACK_PARAM(_conf_) ((_conf_) >> 16)
+#define TZ1090_PINCONF_UNPACK_ARG(_conf_) ((_conf_) & 0xffff)
+
+#endif /* __PINCTRL_TZ1090_H__ */
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists