| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1367542653-955-1-git-send-email-csd@broadcom.com>
Date: Thu, 2 May 2013 17:57:33 -0700
From: "Christian Daudt" <csd@...adcom.com>
To: "Russell King" <linux@....linux.org.uk>,
"John Stultz" <john.stultz@...aro.org>,
"Thomas Gleixner" <tglx@...utronix.de>,
"Olof Johansson" <olof@...om.net>, "Arnd Bergmann" <arnd@...db.de>,
"Stephen Warren" <swarren@...dotorg.org>,
"Will Deacon" <will.deacon@....com>
cc: "Christian Daudt" <csd@...adcom.com>,
"arm@...nel.org" <arm@...nel.org>,
linux-arm-kernel@...ts.infradead.org, csd_b@...dt.org,
"Rob Herring" <rob.herring@...xeda.com>,
"Rob Landley" <rob@...dley.net>,
"Josh Cartwright" <josh.cartwright@...com>,
"Yehuda Yitschak" <yehuday@...vell.com>,
"Gregory CLEMENT" <gregory.clement@...e-electrons.com>,
devicetree-discuss@...ts.ozlabs.org, linux-doc@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH V2] ARM: bcm281xx: Add L2 support for Rev A2 chips
Rev A2 SoCs have an unorthodox memory re-mapping and this needs
to be reflected in the cache operations.
This patch adds new outer cache functions for the l2x0 driver
to support this SoC revision. It also adds a new compatible
value for the cache to enable this functionality.
Updates from V1:
- remove section 1 altogether and note that in comments
- simplify section selection caused by section 1 removal
- BUG_ON just in case section 1 shows up
Signed-off-by: Christian Daudt <csd@...adcom.com>
diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
index cbef09b..69ddf9f 100644
--- a/Documentation/devicetree/bindings/arm/l2cc.txt
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -16,6 +16,9 @@ Required properties:
performs the same operation).
"marvell,"aurora-outer-cache: Marvell Controller designed to be
compatible with the ARM one with outer cache mode.
+ "bcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an
+ offset needs to be added to the address before passing down to the L2
+ cache controller
- cache-unified : Specifies the cache is a unified cache.
- cache-level : Should be set to 2 for a level 2 cache.
- reg : Physical base address and size of cache controller's memory mapped
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi
index 41b2c6c..5e48c85 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/bcm11351.dtsi
@@ -47,10 +47,10 @@
};
L2: l2-cache {
- compatible = "arm,pl310-cache";
- reg = <0x3ff20000 0x1000>;
- cache-unified;
- cache-level = <2>;
+ compatible = "bcm,bcm11351-a2-pl310-cache";
+ reg = <0x3ff20000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
};
timer@...06000 {
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index c465fac..d70e0ab 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -523,6 +523,147 @@ static void aurora_flush_range(unsigned long start, unsigned long end)
}
}
+/*
+ * For certain Broadcom SoCs, depending on the address range, different offsets
+ * need to be added to the address before passing it to L2 for
+ * invalidation/clean/flush
+ *
+ * Section Address Range Offset EMI
+ * 1 0x00000000 - 0x3FFFFFFF 0x80000000 VC
+ * 2 0x40000000 - 0xBFFFFFFF 0x40000000 SYS
+ * 3 0xC0000000 - 0xFFFFFFFF 0x80000000 VC
+ *
+ * When the start and end addresses have crossed two different sections, we
+ * need to break the L2 operation into two, each within its own section.
+ * For example, if we need to invalidate addresses starts at 0xBFFF0000 and
+ * ends at 0xC0001000, we need do invalidate 1) 0xBFFF0000 - 0xBFFFFFFF and 2)
+ * 0xC0000000 - 0xC0001000
+ *
+ * Note 1:
+ * By breaking a single L2 operation into two, we may potentially suffer some
+ * performance hit, but keep in mind the cross section case is very rare
+ *
+ * Note 2:
+ * We do not need to handle the case when the start address is in
+ * Section 1 and the end address is in Section 3, since it is not a valid use
+ * case
+ *
+ * Note 3:
+ * Section 1 in practical terms can no longer be used on rev A2. Because of
+ * that the code does not need to handle section 1 at all.
+ *
+ */
+#define BCM_SYS_EMI_START_ADDR 0x40000000UL
+#define BCM_VC_EMI_SEC3_START_ADDR 0xC0000000UL
+
+#define BCM_SYS_EMI_OFFSET 0x40000000UL
+#define BCM_VC_EMI_OFFSET 0x80000000UL
+
+static inline int bcm_addr_is_sys_emi(unsigned long addr)
+{
+ return (addr >= BCM_SYS_EMI_START_ADDR) &&
+ (addr < BCM_VC_EMI_SEC3_START_ADDR);
+}
+
+static inline unsigned long bcm_l2_phys_addr(unsigned long addr)
+{
+ if (bcm_addr_is_sys_emi(addr))
+ return addr + BCM_SYS_EMI_OFFSET;
+ else
+ return addr + BCM_VC_EMI_OFFSET;
+}
+
+static void bcm_inv_range(unsigned long start, unsigned long end)
+{
+ unsigned long new_start, new_end;
+
+ BUG_ON(start < BCM_SYS_EMI_START_ADDR);
+
+ if (unlikely(end <= start))
+ return;
+
+ new_start = bcm_l2_phys_addr(start);
+ new_end = bcm_l2_phys_addr(end);
+
+ /* normal case, no cross section between start and end */
+ if (likely(bcm_addr_is_sys_emi(end) || !bcm_addr_is_sys_emi(start))) {
+ l2x0_inv_range(new_start, new_end);
+ return;
+ }
+
+ /* They cross sections, so it can only be a cross from section
+ * 2 to section 3
+ */
+ l2x0_inv_range(new_start,
+ bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR-1));
+ l2x0_inv_range(bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR),
+ new_end);
+}
+
+static void bcm_clean_range(unsigned long start, unsigned long end)
+{
+ unsigned long new_start, new_end;
+
+ BUG_ON(start < BCM_SYS_EMI_START_ADDR);
+
+ if (unlikely(end <= start))
+ return;
+
+ if ((end - start) >= l2x0_size) {
+ l2x0_clean_all();
+ return;
+ }
+
+ new_start = bcm_l2_phys_addr(start);
+ new_end = bcm_l2_phys_addr(end);
+
+ /* normal case, no cross section between start and end */
+ if (likely(bcm_addr_is_sys_emi(end) || !bcm_addr_is_sys_emi(start))) {
+ l2x0_clean_range(new_start, new_end);
+ return;
+ }
+
+ /* They cross sections, so it can only be a cross from section
+ * 2 to section 3
+ */
+ l2x0_clean_range(new_start,
+ bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR-1));
+ l2x0_clean_range(bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR),
+ new_end);
+}
+
+static void bcm_flush_range(unsigned long start, unsigned long end)
+{
+ unsigned long new_start, new_end;
+
+ BUG_ON(start < BCM_SYS_EMI_START_ADDR);
+
+ if (unlikely(end <= start))
+ return;
+
+ if ((end - start) >= l2x0_size) {
+ l2x0_flush_all();
+ return;
+ }
+
+ new_start = bcm_l2_phys_addr(start);
+ new_end = bcm_l2_phys_addr(end);
+
+ /* normal case, no cross section between start and end */
+ if (likely(bcm_addr_is_sys_emi(end) || !bcm_addr_is_sys_emi(start))) {
+ l2x0_flush_range(new_start, new_end);
+ return;
+ }
+
+ /* They cross sections, so it can only be a cross from section
+ * 2 to section 3
+ */
+ l2x0_flush_range(new_start,
+ bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR-1));
+ l2x0_flush_range(bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR),
+ new_end);
+}
+
static void __init l2x0_of_setup(const struct device_node *np,
u32 *aux_val, u32 *aux_mask)
{
@@ -765,6 +906,21 @@ static const struct l2x0_of_data aurora_no_outer_data = {
},
};
+static const struct l2x0_of_data bcm_l2x0_data = {
+ .setup = pl310_of_setup,
+ .save = pl310_save,
+ .outer_cache = {
+ .resume = pl310_resume,
+ .inv_range = bcm_inv_range,
+ .clean_range = bcm_clean_range,
+ .flush_range = bcm_flush_range,
+ .sync = l2x0_cache_sync,
+ .flush_all = l2x0_flush_all,
+ .inv_all = l2x0_inv_all,
+ .disable = l2x0_disable,
+ },
+};
+
static const struct of_device_id l2x0_ids[] __initconst = {
{ .compatible = "arm,pl310-cache", .data = (void *)&pl310_data },
{ .compatible = "arm,l220-cache", .data = (void *)&l2x0_data },
@@ -773,6 +929,8 @@ static const struct of_device_id l2x0_ids[] __initconst = {
.data = (void *)&aurora_no_outer_data},
{ .compatible = "marvell,aurora-outer-cache",
.data = (void *)&aurora_with_outer_data},
+ { .compatible = "bcm,bcm11351-a2-pl310-cache",
+ .data = (void *)&bcm_l2x0_data},
{}
};
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists