linux-kernel - Re: KVM VM(rhel-5.5) %si is too high when TX/RX packets

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <D3E216785288A145B7BC975F83A2ED103FE3FE28@szxeml556-mbx.china.huawei.com>
Date:	Sat, 4 May 2013 04:06:39 +0000
From:	"Zhanghaoyu (A)" <haoyu.zhang@...wei.com>
To:	"Zhanghaoyu (A)" <haoyu.zhang@...wei.com>,
	kvm list <kvm@...r.kernel.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	qemu-devel <qemu-devel@...gnu.org>
CC:	Qinchuanyu <qinchuanyu@...wei.com>,
	"Huangweidong (C)" <weidong.huang@...wei.com>,
	Zanghongyong <zanghongyong@...wei.com>,
	Luonengjun <luonengjun@...wei.com>
Subject: Re: KVM VM(rhel-5.5) %si is too high when TX/RX packets

> I running a VM(RHEL-5.5) on KVM hypervisor(linux-3.8 + QEMU-1.4.1), and direct-assign intel 82576 VF to the VM. When TX/RX packets on VM to the other host via iperf tool, top tool result on VM shown that the %si is too high, approximately 95% ~ 100%, but from the view of host, the VM's total CPU usage is about 20% - 30%. And the throughput rate is approximately 200Mb/s, far from the line rate 1Gb/s, And, I found  the hardirq rate is lower than normal by running "watch -d -n 1 cat /proc/interrupts", I think it's caused by the too high %si, because the NIC's hardirq was disabled during the softirq process.
> Then, I direct-assign the intel 82576 to the VM, the same case happened too. 
> I found the intel 82576 and intel 82576 VF's interrupt mode are both PCI-MSI-X.
> 
> And,
> I rmmod the igb driver, and, re-insmod the igb driver(igb-4.1.2) with the parameter IntMode=0/1(0:legacy, 1:MSI, 2:MSI-x), the problem then gone, the %si is approximately 20% -30%, and the throughput rate came to the line rate, about 940Mb/s.
> I update the VM to RHEL-6.1, the problem disappeared too.
> And, I found a very strange thing, the VM's 82576VF's irq routing is set one time on Vf's one interrupt received, so frequently.

With regard to rhel-5.5(linux-2.6.18), in ISR process, mask and unmask msi-x vector function msi_set_mask_bit() was invoked every time, which result in VMEXIT, then QEMU will invoke kvm_irqchip_update_msi_route() to ask KVM hypervisor to update the VM irq routing table. In KVM hypervisor, synchronizing process needed after updating routing table, so much time consumed for waiting in wait_rcu_gp(). 
So %si in VM is so high, while from the view of host, VM's total CPU usage is so low. 

Why in ISR process, masking and unmasking msi-x vector is needed every time? 

Thanks,
Zhang Haoyu
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/