Message-ID: <af51c63e-7ff1-4e73-9305-08309217ab38@TX2EHSMHS037.ehs.local>
Date:	Mon, 13 May 2013 10:58:49 -0700
From:	Sören Brinkmann <soren.brinkmann@...inx.com>
To:	Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>
CC:	Mark Brown <broonie@...nel.org>,
	Mike Turquette <mturquette@...aro.org>,
	<linux-kernel@...r.kernel.org>,
	<linux-arm-kernel@...ts.infradead.org>
Subject: Re: [PATCH RFC] clk: Introduce userspace clock driver

On Mon, May 13, 2013 at 07:37:23PM +0200, Sebastian Hesselbarth wrote:
> On 05/13/13 19:24, Sören Brinkmann wrote:
> >On Mon, May 13, 2013 at 06:21:13PM +0200, Sebastian Hesselbarth wrote:
> >>>Well, that driver actually exists. But that just programs a bitstream
> >>>you give it to program. It does not know anything about the design it
> >>>programs and cannot make any kind of decision whether the clocks should
> >>>be userspace controlled or not.
> >>
> >>what Mark wants to point out is that you add fabric clocks to the Xilinx
> >>driver instead. This way, you will have user-space controllable clocks
> >>but only if you loaded the xilinx driver first.
> >What "Xilinx driver", are we talking about?
> 
> The device config driver you mention below.
> 
> >>IIRC the fabric clock controller provided by Zynq _is_ always there and
> >>accessible from ARM CPUs. You just don't have a new generic driver
> >>allowing to poke with all clocks, but a xilinx only driver allowing you
> >>to set the (xilinx only) fabric clocks.
> >Right.
> >
> >>I've played with Zynq a while ago, did Xilinx mainline the bitfile
> >>driver already? If not, why don't you give it a shot?
> >The device config driver is not in mainline, AFAIK. And I think it's in
> >rather bad shape and needs a lot of work before it is upstreamable. But
> >this is probably the right place to put this.
> 
> It is, as it will only expose clocks on Zynq and that's what Mark and
> Mike are worried about. Expose clocks to user space and you will have
> people mess with it for sure.
Well, even if you contain it in that driver you can still mess with
other clocks. Just give it the "wrong" input clock references in DT and
you are free to control them. As I said before, there is no protection
against such misuse.

> 
> About the shape of it, I didn't expect that to change at all. Just
> wondering, if it still requires you to manually end it's endianess
> mess with the bitfiles. If you go at it, consider reading the magic
> hidden in the bitfile and swap it when it is required. But that will
> go OT here.
It still takes byteswapped, binary images as input, unfortunately.

> 
> >On the other hand, currently this driver is only required for
> >programming the FPGA from Linux, which is not required. One of the
> >bootloaders could do this for you earlier.
> 
> Well, exposing clocks to user space is not required _at all_ on all
> other platforms you can think of. So, if you have a Zynq, you can
> always load a Zynq driver even if you are not going to use it's
> bitfile programming capabilities but only to configure clocks.
> 
> If you don't want to merge both drivers, have a Zynq-only clock
> fabric driver instead?
That was my original intention. But due to the nature of it, it will
always be possible to use it with other clocks too. Hence my generic
approach.
I actually like the idea of making it part of the device config driver.
The downside of it is, that this driver seems a bit far from mainline.

	Sören


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists