| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1369995191-20855-12-git-send-email-gururaja.hebbar@ti.com>
Date: Fri, 31 May 2013 15:43:11 +0530
From: Hebbar Gururaja <gururaja.hebbar@...com>
To: <khilman@...aro.org>, <grant.likely@...aro.org>,
<linus.walleij@...aro.org>, <rob.herring@...xeda.com>
CC: <davinci-linux-open-source@...ux.davincidsp.com>,
<devicetree-discuss@...ts.ozlabs.org>,
<linux-arm-kernel@...ts.infradead.org>, <linux@....linux.org.uk>,
<linux-kernel@...r.kernel.org>, <vaibhav.bedia@...com>,
<sudhakar.raj@...com>, <gururaja.hebbar@...com>,
Tony Lindgren <tony@...mide.com>,
Wolfram Sang <wsa@...-dreams.de>, <linux-omap@...r.kernel.org>,
<linux-i2c@...r.kernel.org>
Subject: [PATCH 11/11] i2c: omap: enhance pinctrl support
Amend the I2C omap pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an i2c transfer
- "idle" after initial default, after resume default, and after each
i2c xfer
- "sleep" on suspend()
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- One is to minimize current leakage from pins and thus save power,
- second, we can prevent the IP from driving pins output in an
uncontrolled manner, which may happen if the power domain drops the
domain regulator.
Note:
A .suspend & .resume callback is added which simply puts the pins to sleep
state upon suspend & are moved to default & idle state upon resume.
If any of the above pin states are missing in dt, a warning message
about the missing state is displayed.
If certain pin-states are not available, to remove this warning message
pass respective state name with null phandler.
(Changes based on i2c-nomadik.c)
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@...com>
Cc: Tony Lindgren <tony@...mide.com>
Cc: Wolfram Sang <wsa@...-dreams.de>
Cc: linux-omap@...r.kernel.org
Cc: linux-i2c@...r.kernel.org
---
:100644 100644 e02f9e3... 588ba28... M drivers/i2c/busses/i2c-omap.c
drivers/i2c/busses/i2c-omap.c | 112 ++++++++++++++++++++++++++++++++++++++---
1 file changed, 105 insertions(+), 7 deletions(-)
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index e02f9e3..588ba28 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -214,7 +214,11 @@ struct omap_i2c_dev {
u16 westate;
u16 errata;
- struct pinctrl *pins;
+ /* Three pin states - default, idle & sleep */
+ struct pinctrl *pinctrl;
+ struct pinctrl_state *pins_default;
+ struct pinctrl_state *pins_idle;
+ struct pinctrl_state *pins_sleep;
};
static const u8 reg_map_ip_v1[] = {
@@ -641,6 +645,11 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
if (IS_ERR_VALUE(r))
goto out;
+ /* Optionaly enable pins to be muxed in and configured */
+ if (!IS_ERR(dev->pins_default))
+ if (pinctrl_select_state(dev->pinctrl, dev->pins_default))
+ dev_err(dev->dev, "could not set default pins\n");
+
r = omap_i2c_wait_for_bb(dev);
if (r < 0)
goto out;
@@ -664,7 +673,13 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
out:
pm_runtime_mark_last_busy(dev->dev);
+
pm_runtime_put_autosuspend(dev->dev);
+ /* Optionally let pins go into idle state */
+ if (!IS_ERR(dev->pins_idle))
+ if (pinctrl_select_state(dev->pinctrl, dev->pins_idle))
+ dev_err(dev->dev, "could not set pins to idle state\n");
+
return r;
}
@@ -1123,14 +1138,47 @@ omap_i2c_probe(struct platform_device *pdev)
dev->set_mpu_wkup_lat = pdata->set_mpu_wkup_lat;
}
- dev->pins = devm_pinctrl_get_select_default(&pdev->dev);
- if (IS_ERR(dev->pins)) {
- if (PTR_ERR(dev->pins) == -EPROBE_DEFER)
+ dev->pinctrl = devm_pinctrl_get(&pdev->dev);
+ if (!IS_ERR(dev->pinctrl)) {
+ dev->pins_default = pinctrl_lookup_state(dev->pinctrl,
+ PINCTRL_STATE_DEFAULT);
+ if (IS_ERR(dev->pins_default))
+ dev_dbg(&pdev->dev, "could not get default pinstate\n");
+ else
+ if (pinctrl_select_state(dev->pinctrl,
+ dev->pins_default))
+ dev_err(&pdev->dev,
+ "could not set default pinstate\n");
+
+ dev->pins_idle = pinctrl_lookup_state(dev->pinctrl,
+ PINCTRL_STATE_IDLE);
+ if (IS_ERR(dev->pins_idle))
+ dev_dbg(&pdev->dev, "could not get idle pinstate\n");
+ else
+ /* If possible, let's idle until the first transfer */
+ if (pinctrl_select_state(dev->pinctrl, dev->pins_idle))
+ dev_err(&pdev->dev,
+ "could not set idle pinstate\n");
+
+ dev->pins_sleep = pinctrl_lookup_state(dev->pinctrl,
+ PINCTRL_STATE_SLEEP);
+ if (IS_ERR(dev->pins_sleep))
+ dev_dbg(&pdev->dev, "could not get sleep pinstate\n");
+ } else {
+ if (PTR_ERR(dev->pinctrl) == -EPROBE_DEFER)
return -EPROBE_DEFER;
- dev_warn(&pdev->dev, "did not get pins for i2c error: %li\n",
- PTR_ERR(dev->pins));
- dev->pins = NULL;
+ /*
+ * Since we continue even when pinctrl node is not found,
+ * Invalidate pins as not available. This is to make sure that
+ * IS_ERR(pins_xxx) results in failure when used.
+ */
+ dev->pins_default = ERR_PTR(-ENODATA);
+ dev->pins_idle = ERR_PTR(-ENODATA);
+ dev->pins_sleep = ERR_PTR(-ENODATA);
+
+ dev_dbg(&pdev->dev, "did not get pins for i2c error: %li\n",
+ PTR_ERR(dev->pinctrl));
}
dev->dev = &pdev->dev;
@@ -1300,6 +1348,10 @@ static int omap_i2c_runtime_suspend(struct device *dev)
omap_i2c_read_reg(_dev, OMAP_I2C_STAT_REG);
}
+ if (!IS_ERR(_dev->pins_idle))
+ if (pinctrl_select_state(_dev->pinctrl, _dev->pins_idle))
+ dev_err(dev, "could not set pins to idle state\n");
+
return 0;
}
@@ -1311,13 +1363,59 @@ static int omap_i2c_runtime_resume(struct device *dev)
if (!_dev->regs)
return 0;
+ /* Optionally place the pins to the default state */
+ if (!IS_ERR(_dev->pins_default))
+ if (pinctrl_select_state(_dev->pinctrl, _dev->pins_default))
+ dev_err(dev, "could not set pins to default state\n");
+
__omap_i2c_init(_dev);
return 0;
}
#endif /* CONFIG_PM_RUNTIME */
+#ifdef CONFIG_PM_SLEEP
+static int omap_i2c_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct omap_i2c_dev *_dev = platform_get_drvdata(pdev);
+
+ pm_runtime_get_sync(dev);
+ if (omap_i2c_wait_for_bb(_dev) < 0) {
+ pm_runtime_put_sync(dev);
+ return -EBUSY;
+ }
+ pm_runtime_put_sync(dev);
+
+ if (!IS_ERR(_dev->pins_sleep))
+ if (pinctrl_select_state(_dev->pinctrl, _dev->pins_sleep))
+ dev_err(dev, "could not set pins to sleep state\n");
+
+ return 0;
+}
+
+static int omap_i2c_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct omap_i2c_dev *_dev = platform_get_drvdata(pdev);
+
+ /* First go to the default state */
+ if (!IS_ERR(_dev->pins_default))
+ if (pinctrl_select_state(_dev->pinctrl, _dev->pins_default))
+ dev_err(dev, "could not set pins to default state\n");
+
+ /* Then let's idle the pins until the next transfer happens */
+ if (!IS_ERR(_dev->pins_idle))
+ if (pinctrl_select_state(_dev->pinctrl, _dev->pins_idle))
+ dev_err(dev, "could not set pins to idle state\n");
+
+ return 0;
+}
+#endif
+
+
static struct dev_pm_ops omap_i2c_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(omap_i2c_suspend, omap_i2c_resume)
SET_RUNTIME_PM_OPS(omap_i2c_runtime_suspend,
omap_i2c_runtime_resume, NULL)
};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists