| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Thu, 20 Jun 2013 15:46:13 +0300
From: Roger Quadros <rogerq@...com>
To: <b-cousson@...com>
CC: <tony@...mide.com>, <linux-omap@...r.kernel.org>,
<devicetree-discuss@...ts.ozlabs.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>, Roger Quadros <rogerq@...com>
Subject: [PATCH v5 1/2] ARM: dts: omap3-beagle-xm: Add USB Host support
Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device. Provide
pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
NOTE: The reset control will be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
Signed-off-by: Roger Quadros <rogerq@...com>
---
arch/arm/boot/dts/omap3-beagle-xm.dts | 81 +++++++++++++++++++++++++++++----
1 files changed, 72 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index afdb164..371b1e2 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -69,6 +69,39 @@
};
};
+
+ /*
+ * Temp hack: Need to be replaced with the proper gpio-controlled
+ * reset driver as soon it will be merged.
+ * http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
+ */
+ /* HS USB Port 2 RESET */
+ hsusb2_reset: hsusb2_reset_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_reset";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 19 0>; /* gpio_147 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-supply = <&hsusb2_reset>;
+ vcc-supply = <&hsusb2_power>;
+ };
};
&omap3_pmx_wkup {
@@ -79,6 +112,37 @@
};
};
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb2_pins
+ >;
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
+ >;
+ };
+
+ hsusbb2_pins: pinmux_hsusbb2_pins {
+ pinctrl-single,pins = <
+ 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+};
+
&i2c1 {
clock-frequency = <2600000>;
@@ -148,15 +212,6 @@
power = <50>;
};
-&omap3_pmx_core {
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
- >;
- };
-};
-
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
@@ -166,3 +221,11 @@
pinctrl-names = "default";
pinctrl-0 = <&gpio1_pins>;
};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists