| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1372930548-19452-1-git-send-email-srinivas.kandagatla@st.com>
Date: Thu, 4 Jul 2013 10:35:48 +0100
From: Srinivas KANDAGATLA <srinivas.kandagatla@...com>
To: netdev@...r.kernel.org
Cc: Giuseppe Cavallaro <peppe.cavallaro@...com>,
Grant Likely <grant.likely@...aro.org>,
Rob Herring <rob.herring@...xeda.com>,
Rob Landley <rob@...dley.net>,
devicetree-discuss@...ts.ozlabs.org, linux-doc@...r.kernel.org,
linux-kernel@...r.kernel.org,
Srinivas Kandagatla <srinivas.kandagatla@...com>
Subject: [PATCH v2 3/3] dt:net:stmmac: Add dt specific phy reset callback support.
From: Srinivas Kandagatla <srinivas.kandagatla@...com>
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@...com>
---
Documentation/devicetree/bindings/net/stmmac.txt | 6 +++
drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 48 ++++++++++++++++++++-
include/linux/stmmac.h | 4 ++
3 files changed, 56 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index e1ddfcc..261c563 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -13,6 +13,12 @@ Required properties:
- phy-mode: String, operation mode of the PHY interface.
Supported values are: "mii", "rmii", "gmii", "rgmii".
- snps,phy-addr phy address to connect to.
+- snps,reset-gpio gpio number for phy reset.
+- snps,reset-active-low boolean flag to indicate if phy reset is active low.
+- snps,reset-delays-us is triplet of delays
+ The 1st cell is reset pre-delay in micro seconds.
+ The 2nd cell is reset pulse in micro seconds.
+ The 3rd cell is reset post-delay in micro seconds.
- snps,pbl Programmable Burst Length
- snps,fixed-burst Program the DMA to use the fixed burst mode
- snps,mixed-burst Program the DMA to use the mixed burst mode
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index cc15039..fe7bc99 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -27,6 +27,9 @@
#include <linux/mii.h>
#include <linux/phy.h>
#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+
#include <asm/io.h>
#include "stmmac.h"
@@ -131,10 +134,46 @@ static int stmmac_mdio_reset(struct mii_bus *bus)
struct net_device *ndev = bus->priv;
struct stmmac_priv *priv = netdev_priv(ndev);
unsigned int mii_address = priv->hw->mii.addr;
+ struct stmmac_mdio_bus_data *data = priv->plat->mdio_bus_data;
+
+#ifdef CONFIG_OF
+ if (priv->device->of_node) {
+ int reset_gpio, active_low;
+
+ if (data->reset_gpio < 0) {
+ struct device_node *np = priv->device->of_node;
+ if (!np)
+ return 0;
+
+ data->reset_gpio = of_get_named_gpio(np,
+ "snps,reset-gpio", 0);
+ if (data->reset_gpio < 0)
+ return 0;
+
+ data->active_low = of_property_read_bool(np,
+ "snps,reset-active-low");
+ of_property_read_u32_array(np,
+ "snps,reset-delays-us", data->delays, 3);
+ }
+
+ reset_gpio = data->reset_gpio;
+ active_low = data->active_low;
+
+ if (!gpio_request(reset_gpio, "mdio-reset")) {
+ gpio_direction_output(reset_gpio, active_low ? 1 : 0);
+ udelay(data->delays[0]);
+ gpio_set_value(reset_gpio, active_low ? 0 : 1);
+ udelay(data->delays[1]);
+ gpio_set_value(reset_gpio, active_low ? 1 : 0);
+ udelay(data->delays[2]);
+ gpio_free(reset_gpio);
+ }
+ }
+#endif
- if (priv->plat->mdio_bus_data->phy_reset) {
+ if (data->phy_reset) {
pr_debug("stmmac_mdio_reset: calling phy_reset\n");
- priv->plat->mdio_bus_data->phy_reset(priv->plat->bsp_priv);
+ data->phy_reset(priv->plat->bsp_priv);
}
/* This is a workaround for problems with the STE101P PHY.
@@ -172,6 +211,11 @@ int stmmac_mdio_register(struct net_device *ndev)
else
irqlist = priv->mii_irq;
+#ifdef CONFIG_OF
+ if (priv->device->of_node)
+ mdio_bus_data->reset_gpio = -1;
+#endif
+
new_bus->name = "stmmac";
new_bus->read = &stmmac_mdio_read;
new_bus->write = &stmmac_mdio_write;
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index c1b3ed3..9e495d31 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -80,6 +80,10 @@ struct stmmac_mdio_bus_data {
unsigned int phy_mask;
int *irqs;
int probed_phy_irq;
+#ifdef CONFIG_OF
+ int reset_gpio, active_low;
+ u32 delays[3];
+#endif
};
struct stmmac_dma_cfg {
--
1.7.6.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists