Message-ID: <51F27F9D.1090902@xs4all.nl>
Date:	Fri, 26 Jul 2013 15:54:37 +0200
From:	Hans Verkuil <hverkuil@...all.nl>
To:	Jon Arne Jørgensen <jonarne@...arne.no>
CC:	linux-media@...r.kernel.org, linux-kernel@...r.kernel.org,
	mchehab@...hat.com, hans.verkuil@...co.com,
	prabhakar.csengg@...il.com, laurent.pinchart@...asonboard.com,
	andriy.shevchenko@...ux.intel.com
Subject: Re: [RFC v3 3/3] saa7115: Implement i2c_board_info.platform_data

Hi Jon Arne,

Patches 1 & 2 look good to me. But I do have a few comments for this one:

On 07/04/2013 01:27 AM, Jon Arne Jørgensen wrote:
> Implement i2c_board_info.platform_data handling in the driver so we can
> make device specific changes to the chips we support.
> 
> I'm adding a new init table for the gm7113c chip because the old saa7113
> init table has a illegal and wrong defaults according to the datasheet.
> 
> I'm also adding an option to the platform_data struct to choose the gm7113c_init
> table even if you are writing a driver for the saa7113 chip.
> 
> This implementation is only adding overrides for the SAA7113 and GM7113C chips.
> 
> Signed-off-by: Jon Arne Jørgensen <jonarne@...arne.no>
> ---
>  drivers/media/i2c/saa7115.c      | 144 ++++++++++++++++++++++++++++++++++++---
>  drivers/media/i2c/saa711x_regs.h |  15 ++++
>  include/media/saa7115.h          |  65 ++++++++++++++++++
>  3 files changed, 215 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/media/i2c/saa7115.c b/drivers/media/i2c/saa7115.c
> index 17a464d..dd51e16 100644
> --- a/drivers/media/i2c/saa7115.c
> +++ b/drivers/media/i2c/saa7115.c
> @@ -225,19 +225,55 @@ static const unsigned char saa7111_init[] = {
>  	0x00, 0x00
>  };
>  
> -/* SAA7113/GM7113C init codes
> - * It's important that R_14... R_17 == 0x00
> - * for the gm7113c chip to deliver stable video
> - */
> +/* This table has one illegal value, and some values that are not
> +   correct according to the datasheet initialization table.
> +
> +   If you need a table with legal/default values tell the driver in
> +   i2c_board_info.platform_data, and you will get the gm7113c_init
> +   table instead. */
> +
> +/* SAA7113 Init codes */
>  static const unsigned char saa7113_init[] = {
>  	R_01_INC_DELAY, 0x08,
>  	R_02_INPUT_CNTL_1, 0xc2,
>  	R_03_INPUT_CNTL_2, 0x30,
>  	R_04_INPUT_CNTL_3, 0x00,
>  	R_05_INPUT_CNTL_4, 0x00,
> -	R_06_H_SYNC_START, 0x89,
> +	R_06_H_SYNC_START, 0x89,	/* Illegal value - min. value = 0x94 */
> +	R_07_H_SYNC_STOP, 0x0d,
> +	R_08_SYNC_CNTL, 0x88,		/* OBS. HTC = VTR Mode - Not default */

Can you mention the correct default in the comment?

> +	R_09_LUMA_CNTL, 0x01,
> +	R_0A_LUMA_BRIGHT_CNTL, 0x80,
> +	R_0B_LUMA_CONTRAST_CNTL, 0x47,
> +	R_0C_CHROMA_SAT_CNTL, 0x40,
> +	R_0D_CHROMA_HUE_CNTL, 0x00,
> +	R_0E_CHROMA_CNTL_1, 0x01,
> +	R_0F_CHROMA_GAIN_CNTL, 0x2a,
> +	R_10_CHROMA_CNTL_2, 0x08,	/* Not datasheet default */

Ditto.

> +	R_11_MODE_DELAY_CNTL, 0x0c,
> +	R_12_RT_SIGNAL_CNTL, 0x07,	/* Not datasheet default */

Ditto.

> +	R_13_RT_X_PORT_OUT_CNTL, 0x00,
> +	R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
> +	R_15_VGATE_START_FID_CHG, 0x00,
> +	R_16_VGATE_STOP, 0x00,
> +	R_17_MISC_VGATE_CONF_AND_MSB, 0x00,
> +
> +	0x00, 0x00
> +};
> +
> +/* GM7113C is a clone of the SAA7113 chip
> +   This init table is copied out of the saa7113 datasheet.
> +   In R_08 we enable "Automatic Field Detection" [AUFD],
> +   this is disabled when saa711x_set_v4lstd is called. */
> +static const unsigned char gm7113c_init[] = {
> +	R_01_INC_DELAY, 0x08,
> +	R_02_INPUT_CNTL_1, 0xc0,
> +	R_03_INPUT_CNTL_2, 0x33,
> +	R_04_INPUT_CNTL_3, 0x00,
> +	R_05_INPUT_CNTL_4, 0x00,
> +	R_06_H_SYNC_START, 0xe9,
>  	R_07_H_SYNC_STOP, 0x0d,
> -	R_08_SYNC_CNTL, 0x88,
> +	R_08_SYNC_CNTL, 0x98,			/* AUFD - BIT7 Enabled */
>  	R_09_LUMA_CNTL, 0x01,
>  	R_0A_LUMA_BRIGHT_CNTL, 0x80,
>  	R_0B_LUMA_CONTRAST_CNTL, 0x47,
> @@ -245,9 +281,9 @@ static const unsigned char saa7113_init[] = {
>  	R_0D_CHROMA_HUE_CNTL, 0x00,
>  	R_0E_CHROMA_CNTL_1, 0x01,
>  	R_0F_CHROMA_GAIN_CNTL, 0x2a,
> -	R_10_CHROMA_CNTL_2, 0x08,
> +	R_10_CHROMA_CNTL_2, 0x00,
>  	R_11_MODE_DELAY_CNTL, 0x0c,
> -	R_12_RT_SIGNAL_CNTL, 0x07,
> +	R_12_RT_SIGNAL_CNTL, 0x01,
>  	R_13_RT_X_PORT_OUT_CNTL, 0x00,
>  	R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
>  	R_15_VGATE_START_FID_CHG, 0x00,
> @@ -1585,6 +1621,85 @@ static const struct v4l2_subdev_ops saa711x_ops = {
>  
>  /* ----------------------------------------------------------------------- */
>  
> +static void saa711x_write_platform_data(struct saa711x_state *state,
> +					struct saa7115_platform_data *data)
> +{
> +	struct v4l2_subdev *sd = &state->sd;
> +	u8 work;
> +
> +	if (state->ident != GM7113C &&
> +	    state->ident != SAA7113)
> +		return;
> +
> +	if (data->saa7113_r08_htc) {
> +		work = saa711x_read(sd, R_08_SYNC_CNTL);
> +		work &= ~SAA7113_R_08_HTC_MASK;
> +		work |= ((*data->saa7113_r08_htc) << SAA7113_R_08_HTC_OFFSET);
> +		if (*data->saa7113_r08_htc != SAA7113_HTC_RESERVED) {
> +			v4l2_dbg(1, debug, sd,
> +				"set R_08 HTC [Mask 0x%02x] [Value 0x%02x]\n",
> +				SAA7113_R_08_HTC_MASK, *data->saa7113_r08_htc);

I would leave out the check against RESERVED (see also my comment later in the
header) and the debug messages in this function. You can always dump the registers
with v4l2-dbg, so I don't think they add a lot.

> +			saa711x_write(sd, R_08_SYNC_CNTL, work);
> +		}
> +	}
> +
> +	if (data->saa7113_r10_vrln) {
> +		work = saa711x_read(sd, R_10_CHROMA_CNTL_2);
> +		work &= ~SAA7113_R_10_VRLN_MASK;
> +		if (*data->saa7113_r10_vrln)
> +			work |= (1 << SAA7113_R_10_VRLN_OFFSET);
> +
> +		v4l2_dbg(1, debug, sd,
> +			 "set R_10 VRLN [Mask 0x%02x] [Value 0x%02x]\n",
> +			 SAA7113_R_10_VRLN_MASK, *data->saa7113_r10_vrln);
> +		saa711x_write(sd, R_10_CHROMA_CNTL_2, work);
> +	}
> +
> +	if (data->saa7113_r10_ofts) {
> +		work = saa711x_read(sd, R_10_CHROMA_CNTL_2);
> +		work &= ~SAA7113_R_10_OFTS_MASK;
> +		work |= (*data->saa7113_r10_ofts << SAA7113_R_10_OFTS_OFFSET);
> +		v4l2_dbg(1, debug, sd,
> +			"set R_10 OFTS [Mask 0x%02x] [Value 0x%02x]\n",
> +			SAA7113_R_10_OFTS_MASK, *data->saa7113_r10_ofts);
> +		saa711x_write(sd, R_10_CHROMA_CNTL_2, work);
> +	}
> +
> +	if (data->saa7113_r12_rts0) {
> +		work = saa711x_read(sd, R_12_RT_SIGNAL_CNTL);
> +		work &= ~SAA7113_R_12_RTS0_MASK;
> +		work |= (*data->saa7113_r12_rts0 << SAA7113_R_12_RTS0_OFFSET);
> +		if (*data->saa7113_r12_rts0 != SAA7113_RTS_DOT_IN) {

I would replace this with a WARN_ON and add a comment as well.

> +			v4l2_dbg(1, debug, sd,
> +				"set R_12 RTS0 [Mask 0x%02x] [Value 0x%02x]\n",
> +				SAA7113_R_12_RTS0_MASK,
> +				*data->saa7113_r12_rts0);
> +			saa711x_write(sd, R_12_RT_SIGNAL_CNTL, work);
> +		}
> +	}
> +
> +	if (data->saa7113_r12_rts1) {
> +		work = saa711x_read(sd, R_12_RT_SIGNAL_CNTL);
> +		work &= ~SAA7113_R_12_RTS1_MASK;
> +		work |= (*data->saa7113_r12_rts1 << SAA7113_R_12_RTS1_OFFSET);
> +		v4l2_dbg(1, debug, sd,
> +			"set R_12 RTS1 [Mask 0x%02x] [Value 0x%02x]\n",
> +			SAA7113_R_12_RTS1_MASK, *data->saa7113_r12_rts1);
> +		saa711x_write(sd, R_12_RT_SIGNAL_CNTL, work);
> +	}
> +
> +	if (data->saa7113_r13_adlsb) {
> +		work = saa711x_read(sd, R_13_RT_X_PORT_OUT_CNTL);
> +		work &= ~SAA7113_R_13_ADLSB_MASK;
> +		if (*data->saa7113_r13_adlsb)
> +			work |= (1 << SAA7113_R_13_ADLSB_OFFSET);
> +		v4l2_dbg(1, debug, sd,
> +			"set R_13 ADLSB [Mask 0x%02x] [Value 0x%02x]\n",
> +			SAA7113_R_13_ADLSB_MASK, *data->saa7113_r13_adlsb);
> +		saa711x_write(sd, R_13_RT_X_PORT_OUT_CNTL, work);
> +	}
> +}
> +
>  /**
>   * saa711x_detect_chip - Detects the saa711x (or clone) variant
>   * @client:		I2C client structure.
> @@ -1693,6 +1808,7 @@ static int saa711x_probe(struct i2c_client *client,
>  	struct saa711x_state *state;
>  	struct v4l2_subdev *sd;
>  	struct v4l2_ctrl_handler *hdl;
> +	struct saa7115_platform_data *pdata;
>  	int ident;
>  	char name[CHIP_VER_SIZE + 1];
>  
> @@ -1756,14 +1872,20 @@ static int saa711x_probe(struct i2c_client *client,
>  
>  	/* init to 60hz/48khz */
>  	state->crystal_freq = SAA7115_FREQ_24_576_MHZ;
> +	pdata = client->dev.platform_data;
>  	switch (state->ident) {
>  	case SAA7111:
>  	case SAA7111A:
>  		saa711x_writeregs(sd, saa7111_init);
>  		break;
>  	case GM7113C:
> +		saa711x_writeregs(sd, gm7113c_init);
> +		break;
>  	case SAA7113:
> -		saa711x_writeregs(sd, saa7113_init);
> +		if (pdata && pdata->saa7113_force_gm7113c_init)
> +			saa711x_writeregs(sd, gm7113c_init);
> +		else
> +			saa711x_writeregs(sd, saa7113_init);
>  		break;
>  	default:
>  		state->crystal_freq = SAA7115_FREQ_32_11_MHZ;
> @@ -1771,6 +1893,10 @@ static int saa711x_probe(struct i2c_client *client,
>  	}
>  	if (state->ident > SAA7111A && state->ident != GM7113C)
>  		saa711x_writeregs(sd, saa7115_init_misc);
> +
> +	if (pdata)
> +		saa711x_write_platform_data(state, pdata);
> +
>  	saa711x_set_v4lstd(sd, V4L2_STD_NTSC);
>  	v4l2_ctrl_handler_setup(hdl);
>  
> diff --git a/drivers/media/i2c/saa711x_regs.h b/drivers/media/i2c/saa711x_regs.h
> index 70c56d1..730ca90 100644
> --- a/drivers/media/i2c/saa711x_regs.h
> +++ b/drivers/media/i2c/saa711x_regs.h
> @@ -202,9 +202,24 @@
>  #define R_FF_S_PLL_MAX_PHASE_ERR_THRESH_NUM_LINES     0xff
>  
>  /* SAA7113 bit-masks */
> +#define SAA7113_R_08_HTC_OFFSET 3
> +#define SAA7113_R_08_HTC_MASK (0x3 << SAA7113_R_08_HTC_OFFSET)
>  #define SAA7113_R_08_FSEL 0x40
>  #define SAA7113_R_08_AUFD 0x80
>  
> +#define SAA7113_R_10_VRLN_OFFSET 3
> +#define SAA7113_R_10_VRLN_MASK (0x1 << SAA7113_R_10_VRLN_OFFSET)
> +#define SAA7113_R_10_OFTS_OFFSET 6
> +#define SAA7113_R_10_OFTS_MASK (0x3 << SAA7113_R_10_OFTS_OFFSET)
> +
> +#define SAA7113_R_12_RTS0_OFFSET 0
> +#define SAA7113_R_12_RTS0_MASK (0xf << SAA7113_R_12_RTS0_OFFSET)
> +#define SAA7113_R_12_RTS1_OFFSET 4
> +#define SAA7113_R_12_RTS1_MASK (0xf << SAA7113_R_12_RTS1_OFFSET)
> +
> +#define SAA7113_R_13_ADLSB_OFFSET 7
> +#define SAA7113_R_13_ADLSB_MASK (0x1 << SAA7113_R_13_ADLSB_OFFSET)
> +
>  #if 0
>  /* Those structs will be used in the future for debug purposes */
>  struct saa711x_reg_descr {
> diff --git a/include/media/saa7115.h b/include/media/saa7115.h
> index 4079186..d2e5a37 100644
> --- a/include/media/saa7115.h
> +++ b/include/media/saa7115.h
> @@ -64,5 +64,70 @@
>  #define SAA7115_FREQ_FL_APLL         (1 << 2) /* SA 3A[3], APLL, SAA7114/5 only */
>  #define SAA7115_FREQ_FL_DOUBLE_ASCLK (1 << 3) /* SA 39, LRDIV, SAA7114/5 only */
>  
> +/* ===== SAA7113 Config enums ===== */
> +
> +/* Register 0x08 "Horizontal time constant" [Bit 3..4]:
> + * Should be set to "Fast Locking Mode" according to the datasheet,
> + * and that is the default setting in the gm7113c_init table.
> + * saa7113_init sets this value to "VTR Mode". */
> +enum saa7113_r08_htc {
> +	SAA7113_HTC_TV_MODE = 0x00,
> +	SAA7113_HTC_VTR_MODE,		/* Default for saa7113_init */
> +	SAA7113_HTC_RESERVED,		/* DO NOT USE */

If it shouldn't be used, then it shouldn't be defined :-) So drop it,

> +	SAA7113_HTC_FAST_LOCKING_MODE	/* Default for gm7113c_init */

and instead use this:

	SAA7113_HTC_FAST_LOCKING_MODE = 0x03	/* Default for gm7113c_init */

> +};
> +
> +/* Register 0x10 "Output format selection" [Bit 6..7]:
> + * Defaults to ITU_656 as specified in datasheet. */
> +enum saa7113_r10_ofts {
> +	SAA7113_OFTS_ITU_656 = 0x0,	/* Default */
> +	SAA7113_OFTS_VFLAG_BY_VREF,
> +	SAA7113_OFTS_VFLAG_BY_DATA_TYPE
> +};
> +
> +/* Register 0x12 "Output control" [Bit 0..3 Or Bit 4..7]:
> + * This is used to select what data is output on the RTS0 and RTS1 pins.
> + * RTS1 [Bit 4..7] Defaults to DOT_IN. (This value can not be set for RTS0)
> + * RTS0 [Bit 0..3] Defaults to VIPB in gm7113c_init as specified
> + * in the datasheet, but is set to HREF_HS in the saa7113_init table. */
> +enum saa7113_r12_rts {
> +	SAA7113_RTS_DOT_IN = 0,		/* OBS: Only for RTS1 (Default RTS1) */
> +	SAA7113_RTS_VIPB,		/* Default RTS0 For gm7113c_init */
> +	SAA7113_RTS_GPSW,
> +	SAA7115_RTS_HL,
> +	SAA7113_RTS_VL,
> +	SAA7113_RTS_DL,
> +	SAA7113_RTS_PLIN,
> +	SAA7113_RTS_HREF_HS,		/* Default RTS0 For saa7113_init */
> +	SAA7113_RTS_HS,
> +	SAA7113_RTS_HQ,
> +	SAA7113_RTS_ODD,
> +	SAA7113_RTS_VS,
> +	SAA7113_RTS_V123,
> +	SAA7113_RTS_VGATE,
> +	SAA7113_RTS_VREF,
> +	SAA7113_RTS_FID
> +};
> +
> +struct saa7115_platform_data {
> +	/* saa7113 only: Force the use of the gm7113c_init table,
> +	 * instead of the old saa7113_init table. */
> +	bool saa7113_force_gm7113c_init;
> +
> +	/* SAA7113/GM7113C Specific configurations */
> +	enum saa7113_r08_htc *saa7113_r08_htc;	/* [R_08 - Bit 3..4] */
> +
> +	bool *saa7113_r10_vrln;			/* [R_10 - Bit 3]
> +						   Disabled for gm7113c_init
> +						   Enabled for saa7113c_init */
> +	enum saa7113_r10_ofts *saa7113_r10_ofts;	/* [R_10 - Bit 6..7] */
> +
> +	enum saa7113_r12_rts *saa7113_r12_rts0;		/* [R_12 - Bit 0..3] */
> +	enum saa7113_r12_rts *saa7113_r12_rts1;		/* [R_12 - Bit 4..7] */
> +
> +	bool *saa7113_r13_adlsb;			/* [R_13 - Bit 7]
> +							   Default disabled */
> +};
> +
>  #endif
>  
> 

Regards,

	Hans
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists