Message-ID: <520A34AD.3020806@ti.com>
Date:	Tue, 13 Aug 2013 09:29:17 -0400
From:	Santosh Shilimkar <santosh.shilimkar@...com>
To:	Sricharan R <r.sricharan@...com>
CC:	Tony Lindgren <tony@...mide.com>, Nishanth Menon <nm@...com>,
	Linus Walleij <linus.walleij@...aro.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	"devicetree-discuss@...ts.ozlabs.org" 
	<devicetree-discuss@...ts.ozlabs.org>,
	"linux-doc@...r.kernel.org" <linux-doc@...r.kernel.org>,
	"linux-arm-kernel@...ts.infradead.org" 
	<linux-arm-kernel@...ts.infradead.org>,
	Linux-OMAP <linux-omap@...r.kernel.org>,
	Russell King - ARM Linux <linux@....linux.org.uk>,
	Rajendra Nayak <rnayak@...com>, Felipe Balbi <balbi@...com>,
	Thomas Gleixner <tglx@...utronix.de>,
	Grant Likely <grant.likely@...retlab.ca>
Subject: Re: [PATCH 1/3] misc: Add crossbar driver

On Tuesday 13 August 2013 05:56 AM, Sricharan R wrote:
> Hi Tony,
> 
> On Tuesday 13 August 2013 01:40 PM, Tony Lindgren wrote:
>> * Santosh Shilimkar <santosh.shilimkar@...com> [130724 12:06]:
>>> On Wednesday 24 July 2013 02:51 PM, Nishanth Menon wrote:
>>>> On 07/24/2013 01:43 PM, Sricharan R wrote:
>>>>> On Wednesday 24 July 2013 10:17 PM, Nishanth Menon wrote:
>>>>>> On 07/24/2013 11:38 AM, Santosh Shilimkar wrote:
>>>>>>> On Wednesday 24 July 2013 12:08 PM, Nishanth Menon wrote:
>>>>>>>> That said, maybe a intermediate pinctrl approach might be more pragmatic and less theoretically flexible.
>>>>>>>> an option might be to "statically allocate" default number of interrupts to a domain - example:
>>>>>>>> * GIC IRQ 72->78 allotted to UARTs
>>>>>>>> * pinctrl mapping provided for those but only 6 can be used (rest are marked status="disabled" as default) at any given time (choice of pinctrl option determines GIC interrupt line to use)
>>>>>>>> * All modules will have a pinctrl definition to have a mapping - to avoid bootloader overriding default cross bar setting in ways un-expected by kernel.
>>>>>>>>
>>>>>>>> Does that sound fair trade off?
>>>>>>> This sounds better. That way we can get all the devices in the DT at least.
>>>>>> Fair enough - if Linus and Tony are still ok with this approach to the problem, seeing a patch series with the effect would be beneficial.
>>>>>>
>>>>>   Ok, i will use this idea of certain number interrupts to groups.
>>>>> Yes on DRA7XX, we have about 160 gic lines and 320 irq crossbar device inputs contending for it.
>>>>> 1:2 and fully arbitrary.  But will we be really exhausting them ?
>>>>>
>>>> Depends on how we allocate :). The default arbitary allocation can be made more logical in your series ofcourse :).
>>>>
>>> I would just most logical peripherals rather than providing every single
>>> IP connected to cross bar. Otherwise we will end up wth hwmod like
>>> scenario where now started removing the unused stuff because of
>>> maintenance and loc issues ;-)
>> Sorry for the delay on this, I think the best way to set this up
>> is as a separate drivers/irqchip controller. Then just map the
>> configured interrupts for the board with interrupt-map and
>> interrupt-map-mask binding. No need to stuff all the SoC specific
>> maps to the .dts, just the ones used for the board.
>>
>> Regards,
>>
>> Tony
>>  
>  Initially irqchip was discussed, but we also have a DMA crossbar
>  to map the dma-requests. Since both irq/dma crossbars should be handled,
>  pinctrl was suggested as the appropriate place to handle this.
> 
I replied on other thread. I guess Tony's point is to setup only required
events for a board rather than setting up every possible event.

Regards,
Santosh

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists