Message-ID: <81108254.GSTBHzP5cb@vostro.rjw.lan>
Date:	Thu, 05 Sep 2013 13:57:01 +0200
From:	"Rafael J. Wysocki" <rjw@...k.pl>
To:	Lan Tianyu <lantianyu1986@...il.com>
Cc:	Alex Williamson <alex.williamson@...hat.com>,
	ACPI Devel Maling List <linux-acpi@...r.kernel.org>,
	Bjorn Helgaas <bhelgaas@...gle.com>,
	LKML <linux-kernel@...r.kernel.org>,
	Linux PCI <linux-pci@...r.kernel.org>,
	Yinghai Lu <yinghai@...nel.org>, Jiang Liu <liuj97@...il.com>,
	Mika Westerberg <mika.westerberg@...ux.intel.com>,
	"Kirill A. Shutemov" <kirill.shutemov@...ux.intel.com>
Subject: Re: [PATCH 25/30] ACPI / hotplug / PCI: Check for new devices on enabled slots

On Thursday, September 05, 2013 02:17:06 PM Lan Tianyu wrote:
> 2013/9/5 Alex Williamson <alex.williamson@...hat.com>:
> > On Thu, 2013-09-05 at 01:35 +0200, Rafael J. Wysocki wrote:
> >> On Wednesday, September 04, 2013 05:12:14 PM Alex Williamson wrote:
> >> > On Thu, 2013-09-05 at 00:54 +0200, Rafael J. Wysocki wrote:
> >> > > On Wednesday, September 04, 2013 02:36:34 PM Alex Williamson wrote:
> >> > > > On Thu, 2013-07-18 at 01:32 +0200, Rafael J. Wysocki wrote:
> >> > > > > From: Rafael J. Wysocki <rafael.j.wysocki@...el.com>
> >> > > > >
> >> > > > > The current implementation of acpiphp_check_bridge() is pretty dumb:
> >> > > > >  - It enables a slot if it's not enabled and the slot status is
> >> > > > >    ACPI_STA_ALL.
> >> > > > >  - It disables a slot if it's enabled and the slot status is not
> >> > > > >    ACPI_STA_ALL.
> >> > > > >
> >> > > > > This behavior is not sufficient to handle the Thunderbolt daisy
> >> > > > > chaining case properly, however, because in that case the bus
> >> > > > > behind the already enabled slot needs to be rescanned for new
> >> > > > > devices.
> >> > > > >
> >> > > > > For this reason, modify acpiphp_check_bridge() so that slots are
> >> > > > > disabled and stopped if they are not in the ACPI_STA_ALL state.
> >> > > > >
> >> > > > > For slots in the ACPI_STA_ALL state, devices behind them that don't
> >> > > > > respond are trimmed using a new function, trim_stale_devices(),
> >> > > > > introduced specifically for this purpose.  That function walks
> >> > > > > the given bus and checks each device on it.  If the device doesn't
> >> > > > > respond, it is assumed to be gone and is removed.
> >> > > > >
> >> > > > > Once all of the stale devices directy behind the slot have been
> >> > > > > removed, acpiphp_check_bridge() will start looking for new devices
> >> > > > > that might have appeared on the given bus.  It will do that even if
> >> > > > > the slot is already enabled (SLOT_ENABLED is set for it).
> >> > > > >
> >> > > > > In addition to that, make the bus check notification ignore
> >> > > > > SLOT_ENABLED and go for enable_device() directly if bridge is NULL,
> >> > > > > so that devices behind the slot are re-enumerated in that case too.
> >> > > > >
> >> > > > > This change is based on earlier patches from Kirill A Shutemov
> >> > > > > and Mika Westerberg.
> >> > > > >
> >> > > > > Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@...el.com>
> >> > > > > Tested-by: Mika Westerberg <mika.westerberg@...ux.intel.com>
> >> > > > > ---
> >> > > >
> >> > > > FYI, git bisect landed on this patch as the cause of my serial console
> >> > > > dying on current upstream.  Further debugging to come...  Thanks,
> >> > >
> >> > > Well, sorry about that.
> >> > >
> >> > > What exactly do you mean by "dying"?
> >> >
> >> > Sorry, I was hoping to have more details quickly, but it's been a pain
> >> > to debug.  By dying I mean serial console output suddenly stops during
> >> > kernel boot and nothing more comes out of it until after the system is
> >> > rebooted.  The problem happens when acpiphp_check_bridge() calls
> >> > enable_slot().  The serial console dies somewhere down in
> >> > acpiphp_bus_trim().  I think this is happening on the 00:1f ISA bridge,
> >> > so there's a good chance the serial ports are described as somewhere
> >> > under there.
> >>
> >> Can you please check if that is the acpiphp_bus_trim() called by
> >> acpiphp_bus_add() or the other one called from trim_stale_devices()?
> >>
> >> Just add a dump_stack() or WARN_ON(1) to trim_stale_devices() next to
> >> the acpiphp_bus_trim() call and see if that triggers.  I *think* it's the one
> >> in acpiphp_bus_add(), but it won't hurt to verify that.
> >
> > Here's the call path:
> >
> > [   16.120824]  [<ffffffff81627e6c>] dump_stack+0x55/0x76
> > [   16.125979]  [<ffffffff8162132e>] enable_slot+0x4ee/0x5e0
> > [   16.131396]  [<ffffffff813418fb>] ? trim_stale_devices+0x5b/0xf0
> > [   16.137420]  [<ffffffff81341b35>] acpiphp_check_bridge+0xd5/0x110
> > [   16.143531]  [<ffffffff81342acb>] hotplug_event+0x16b/0x260
> > [   16.149115]  [<ffffffff81072cd9>] ? process_one_work+0x189/0x540
> > [   16.155136]  [<ffffffff81342bf0>] hotplug_event_work+0x30/0x70
> > [   16.160978]  [<ffffffff81072d3b>] process_one_work+0x1eb/0x540
> > [   16.166819]  [<ffffffff81072cd9>] ? process_one_work+0x189/0x540
> > [   16.172836]  [<ffffffff8107353c>] worker_thread+0x11c/0x370
> > [   16.178426]  [<ffffffff81073420>] ? rescuer_thread+0x350/0x350
> > [   16.184276]  [<ffffffff8107b0ea>] kthread+0xea/0xf0
> > [   16.189165]  [<ffffffff8107b000>] ? kthread_create_on_node+0x160/0x160
> > [   16.195700]  [<ffffffff816395dc>] ret_from_fork+0x7c/0xb0
> > [   16.201109]  [<ffffffff8107b000>] ? kthread_create_on_node+0x160/0x160
> >
> > The actual death of the serial console occurs in acpi_device_set_power()
> > called from:
> >
> > enable_slot()
> >  acpiphp_bus_add()
> >   acpiphp_bus_trim()
> >    acpi_bus_trim()
> >     acpi_walk_namespace()
> >      acpi_bus_remove()
> >       acpi_device_unregister()
> >        acpi_device_set_power()
> >
> > I can't seem to get a path from the acpi devices in question there, so I
> > have no idea what's getting trimmed here.  It worries me quite a bit by
> > introducing this trimming that apparently wasn't happening before
> > though.  Thanks,
> 
> Hi Alex:
>            Could you apply the following patch and bootup with kernel param
> "acpiphp.acpiphp_debug=1"?
>            I guess the patch can make serial port alive. It will not
> be put into D3cold
> during trimming. But I don't know why it doesn't work after being put
> back to D0.

Do we actually put it into D0 in acpi_bus_scan()?  I don't think so.

> So please attach output of acpidump and the dmesg if it can work. Thanks.
> 
> diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c
> index e763651..359b23d 100644
> --- a/drivers/acpi/scan.c
> +++ b/drivers/acpi/scan.c
> @@ -1110,7 +1110,7 @@ static void acpi_device_unregister(struct
> acpi_device *device)
>          * power resources the device depends on and turn off the ones that have
>          * no more references.
>          */
> -       acpi_device_set_power(device, ACPI_STATE_D3_COLD);
> +       //acpi_device_set_power(device, ACPI_STATE_D3_COLD);
>         device->handle = NULL;
>         put_device(&device->dev);
>  }

I don't think we should do the trimming in acpiphp_bus_add() at all.

Thanks,
Rafael

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists