linux-kernel - Re: using mmc2 on panda [was: Regression 3.11-rc1: omap4panda: no usb and consequently no ethernet]

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <524ACBC6.5060208@ti.com>
Date:	Tue, 1 Oct 2013 18:49:02 +0530
From:	Balaji T K <balajitk@...com>
To:	Arend van Spriel <arend@...adcom.com>
CC:	Roger Quadros <rogerq@...com>, Tony Lindgren <tony@...mide.com>,
	<linux-omap@...r.kernel.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	<luca@...lho.fi>
Subject: Re: using mmc2 on panda [was: Regression 3.11-rc1: omap4panda: no
 usb and consequently no ethernet]

>>>>> Hi Roger,
>>>>>
>>>>> It has been a while, but I would like to pickup this thread. We have a couple of pandaboards used as test setup. These have an SDIO adapter hooked up to expansion connector A using MMC2. I have attached the patch file (just ignore platform_data stuff). Now on one board it works, but not for the other. I suspect a board issue so listing the two types that we use:
>>>>>
>>>>> PandaBoard rev A2 (dmesg: OMAP4430 ES2.1): works
>>>>> PandaBoardES rev B1 (dmesg: OMAP4460 ES1.1): nope
>>>>>
>>>>> Any hints for me.
>>>>
>>>> Does your PandaboardES have the WLAN chip (U4) mounted? If yes, how do you isolate
>>>> it from your external SDIO adapter?
>>
>> On my 4460 board in front of me U4 is not populated, but U3 is (the TiWi thing).
>>
>>>
>>> OK, just realized that the expansion connector uses different pads for MMC2. However, you still
>>> need to make sure that the other pins (connected to on board WLAN chip) are not muxed as MMC2.
>>
>> I think Luciano added DT patches for on-board WLAN and it uses MMC5 if I am not mistaken(?). Attached are the dmesg logs of the two boards.
>
> Right. WLAN is supposed to use MMC5. But if you don't have Luca's patches, can you please ensure that those pins are muxed either as safe mode
> or as MMC5? Default seems to be safe mode, but you should cross check.
>
> Also in your patches you have set mmc2-clk to PIN_INPUT_PULLUP
> Shouldn't it be PIN_OUTPUT?
>
> Still I have no clue why it works on 4430 and not on 4460. Are you using the same bootloader image on both boards?
>
if you are using vaux1, can you check the voltage levels,

 From dmesg you attached,
vaux1 is set to 1.8V on omap4430 and to 2.8V on OMAP4460

4430
[    2.425750] VAUX1_6030: 1000 <--> 3000 mV at 1800 mV

4460
[    2.244262] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV

Can you also check with MMC_DEBUG enabled for any clues.

> cheers,
> -roger
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@...r.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/