| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20131017174426.GA12494@kroah.com>
Date: Thu, 17 Oct 2013 10:44:26 -0700
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To: linux-serial@...r.kernel.org
Cc: linux-kernel@...r.kernel.org,
Amanda Ying <amanda_ying@...tek.com.tw>,
Felix Shih <felix_shih@...tek.com.tw>
Subject: [PATCH]: serial: 8250_pci: add support for Fintek 4, 8, and 12 port
cards
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.
Thanks to Fintek for the sample devices, and the spec needed in order to
implement this.
Cc: Amanda Ying <amanda_ying@...tek.com.tw>
Cc: Felix Shih <felix_shih@...tek.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
---
drivers/tty/serial/8250/8250_pci.c | 112 +++++++++++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1343,6 +1343,71 @@ pci_brcm_trumanage_setup(struct serial_p
return ret;
}
+static int pci_fintek_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ struct pci_dev *pdev = priv->dev;
+ unsigned long base;
+ unsigned long iobase;
+ unsigned long ciobase = 0;
+ u8 config_base;
+
+ /*
+ * We are supposed to be able to read these from the PCI config space,
+ * but the values there don't seem to match what we need to use, so
+ * just use these hard-coded values for now, as they are correct.
+ */
+ switch (idx) {
+ case 0: iobase = 0xe000; config_base = 0x40; break;
+ case 1: iobase = 0xe008; config_base = 0x48; break;
+ case 2: iobase = 0xe010; config_base = 0x50; break;
+ case 3: iobase = 0xe018; config_base = 0x58; break;
+ case 4: iobase = 0xe020; config_base = 0x60; break;
+ case 5: iobase = 0xe028; config_base = 0x68; break;
+ case 6: iobase = 0xe030; config_base = 0x70; break;
+ case 7: iobase = 0xe038; config_base = 0x78; break;
+ case 8: iobase = 0xe040; config_base = 0x80; break;
+ case 9: iobase = 0xe048; config_base = 0x88; break;
+ case 10: iobase = 0xe050; config_base = 0x90; break;
+ case 11: iobase = 0xe058; config_base = 0x98; break;
+ default:
+ /* Unknown number of ports, get out of here */
+ return -EINVAL;
+ }
+
+ if (idx < 4) {
+ base = pci_resource_start(priv->dev, 3);
+ ciobase = (int)(base + (0x8 * idx));
+ }
+
+ dev_dbg(&pdev->dev, "%s: idx=%d iobase=0x%lx ciobase=0x%lx config_base=0x%2x\n",
+ __func__, idx, iobase, ciobase, config_base);
+
+ /* Enable UART I/O port */
+ pci_write_config_byte(pdev, config_base + 0x00, 0x01);
+
+ /* Select 128-byte FIFO and 8x FIFO threshold */
+ pci_write_config_byte(pdev, config_base + 0x01, 0x33);
+
+ /* LSB UART */
+ pci_write_config_byte(pdev, config_base + 0x04, (u8)(iobase & 0xff));
+
+ /* MSB UART */
+ pci_write_config_byte(pdev, config_base + 0x05, (u8)((iobase & 0xff00) >> 8));
+
+ /* irq number, this usually fails, but the spec says to do it anyway. */
+ pci_write_config_byte(pdev, config_base + 0x06, pdev->irq);
+
+ port->port.iotype = UPIO_PORT;
+ port->port.iobase = iobase;
+ port->port.mapbase = 0;
+ port->port.membase = NULL;
+ port->port.regshift = 0;
+
+ return 0;
+}
+
static int skip_tx_en_setup(struct serial_private *priv,
const struct pciserial_board *board,
struct uart_8250_port *port, int idx)
@@ -2252,6 +2317,27 @@ static struct pci_serial_quirk pci_seria
.subdevice = PCI_ANY_ID,
.setup = pci_brcm_trumanage_setup,
},
+ {
+ .vendor = 0x1c29,
+ .device = 0x1104,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_fintek_setup,
+ },
+ {
+ .vendor = 0x1c29,
+ .device = 0x1108,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_fintek_setup,
+ },
+ {
+ .vendor = 0x1c29,
+ .device = 0x1112,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_fintek_setup,
+ },
/*
* Default "match everything" terminator entry
@@ -2449,6 +2535,9 @@ enum pci_board_num_t {
pbn_omegapci,
pbn_NETMOS9900_2s_115200,
pbn_brcm_trumanage,
+ pbn_fintek_4,
+ pbn_fintek_8,
+ pbn_fintek_12,
};
/*
@@ -3199,6 +3288,24 @@ static struct pciserial_board pci_boards
.reg_shift = 2,
.base_baud = 115200,
},
+ [pbn_fintek_4] = {
+ .num_ports = 4,
+ .uart_offset = 8,
+ .base_baud = 115200,
+ .first_offset = 0x40,
+ },
+ [pbn_fintek_8] = {
+ .num_ports = 8,
+ .uart_offset = 8,
+ .base_baud = 115200,
+ .first_offset = 0x40,
+ },
+ [pbn_fintek_12] = {
+ .num_ports = 12,
+ .uart_offset = 8,
+ .base_baud = 115200,
+ .first_offset = 0x40,
+ },
};
static const struct pci_device_id blacklist[] = {
@@ -4916,6 +5023,11 @@ static struct pci_device_id serial_pci_t
0,
0, pbn_exar_XR17V358 },
+ /* Fintek PCI serial cards */
+ { PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
+ { PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
+ { PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12 },
+
/*
* These entries match devices with class COMMUNICATION_SERIAL,
* COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists