[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20131120145926.GE14627@ns203013.ovh.net>
Date: Wed, 20 Nov 2013 15:59:26 +0100
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@...osoft.com>
To: Boris BREZILLON <b.brezillon@...rkiz.com>
Cc: Rob Herring <rob.herring@...xeda.com>,
Pawel Moll <pawel.moll@....com>,
Mark Rutland <mark.rutland@....com>,
Stephen Warren <swarren@...dotorg.org>,
Ian Campbell <ian.campbell@...rix.com>,
Russell King <linux@....linux.org.uk>,
Nicolas Ferre <nicolas.ferre@...el.com>,
Joachim Eastwood <manabian@...il.com>,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH 5/9] ARM: at91/dt: add mmc0 slot0 support to at91rm9200ek
board
On 13:06 Wed 28 Aug , Boris BREZILLON wrote:
> Add slot0 of mmc0 pinctrl pins definitions:
> - detect pin
> - write protect pin
> - enable slot0 pin: this pin is connected to an external switch which
> enable mmc0 slot0 or spi dataflash connected to cs3
>
> The mmc0 device is not enabled, as it depends on the choosen functionnality
> (spi cs3 or mmc0 slot0).
>
> Signed-off-by: Boris BREZILLON <b.brezillon@...rkiz.com>
> ---
> arch/arm/boot/dts/at91rm9200ek.dts | 35 +++++++++++++++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
> index f2d6d79..2bad423 100644
> --- a/arch/arm/boot/dts/at91rm9200ek.dts
> +++ b/arch/arm/boot/dts/at91rm9200ek.dts
> @@ -39,6 +39,23 @@
> atmel,pins = <AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
> };
> };
> +
> + mmc0 {
> + pinctrl_mmc0_slot0_detect: mmc0_slot0_detect-0 {
> + atmel,pins =
> + <AT91_PIOB 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> + };
> +
> + pinctrl_mmc0_slot0_write_protect: mmc0_slot0_write_protect-0 {
> + atmel,pins =
> + <AT91_PIOA 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_mmc0_slot0_switch: mmc0_slot0_switch-0 {
> + atmel,pins =
> + <AT91_PIOB 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(1))>;
> + };
nack this is a regulator the pinctrl API is not done for gpio default value
> + };
> };
>
> dbgu: serial@...ff200 {
> @@ -84,6 +101,24 @@
> reg = <0>;
> };
> };
> +
> + mmc0: mmc@...b4000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pinctrl_mmc0_clk
> + &pinctrl_mmc0_slot0_cmd_dat0
> + &pinctrl_mmc0_slot0_dat1_3
> + &pinctrl_mmc0_slot0_detect
> + &pinctrl_mmc0_slot0_write_protect
> + &pinctrl_mmc0_slot0_switch>;
> +
> + slot0: slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioB 27 GPIO_ACTIVE_HIGH>;
> + wp-gpios = <&pioA 17 GPIO_ACTIVE_HIGH>;
> + };
> + };
> };
>
> usb0: ohci@...00000 {
> --
> 1.7.9.5
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists