[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <1385033305-13179-7-git-send-email-ivan.khoronzhuk@ti.com>
Date: Thu, 21 Nov 2013 13:28:21 +0200
From: Ivan Khoronzhuk <ivan.khoronzhuk@...com>
To: Santosh Shilimkar <santosh.shilimkar@...com>,
Rob Landley <rob@...dley.net>,
Russell King <linux@....linux.org.uk>
CC: <devicetree@...r.kernel.org>, Pawel Moll <pawel.moll@....com>,
Mark Rutland <mark.rutland@....com>,
Rob Herring <rob.herring@...xeda.com>,
Stephen Warren <swarren@...dotorg.org>,
Kumar Gala <galak@...nel.crashing.org>,
Ian Campbell <ijc+devicetree@...lion.org.uk>,
<linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-mtd@...ts.infradead.org>, <grygorii.strashko@...com>,
Ivan Khoronzhuk <ivan.khoronzhuk@...com>
Subject: [PATCH v2 06/10] mtd: nand: davinci: extend description of bindings
Extend bindings for davinci_nand driver to be more clear.
This is clarification only, without semantic changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@...com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@...com>
---
.../devicetree/bindings/mtd/davinci-nand.txt | 77 ++++++++++++++------
1 file changed, 54 insertions(+), 23 deletions(-)
diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
index 3545ea7..d2a3fc0 100644
--- a/Documentation/devicetree/bindings/mtd/davinci-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
@@ -1,36 +1,67 @@
-* Texas Instruments Davinci NAND
+Device tree bindings for Texas instruments Davinci NAND controller
-This file provides information, what the device node for the
-davinci nand interface contain.
+This file provides information, what the device node for the davinci NAND
+interface contains.
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
Required properties:
-- compatible: "ti,davinci-nand";
-- reg : contain 2 offset/length values:
- - offset and length for the access window
- - offset and length for accessing the aemif control registers
-- ti,davinci-chipselect: Indicates on the davinci_nand driver which
- chipselect is used for accessing the nand.
+
+- compatible: "ti,davinci-nand"
+
+- reg: Contains 2 offset/length values:
+ - offset and length for the access window.
+ - offset and length for accessing the AEMIF
+ control registers.
+
+- ti,davinci-chipselect: number of chipselect. Indicates on the
+ davinci_nand driver which chipselect is used
+ for accessing the nand.
+ Can be in the range [0-3].
Recommended properties :
-- ti,davinci-mask-ale: mask for ale
-- ti,davinci-mask-cle: mask for cle
-- ti,davinci-mask-chipsel: mask for chipselect
-- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
- - "none"
- - "soft"
- - "hw"
-- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
-- ti,davinci-nand-buswidth: buswidth 8 or 16
-- ti,davinci-nand-use-bbt: use flash based bad block table support.
-
-nand device bindings may contain additional sub-nodes describing
-partitions of the address space. See partition.txt for more detail.
+
+- ti,davinci-mask-ale: mask for ALE. Needed for executing address
+ phase. These offset will be added to the base
+ address for the chip select space the NAND Flash
+ device is connected to.
+ If not set equal to 0x08.
+
+- ti,davinci-mask-cle: mask for CLE. Needed for executing command
+ phase. These offset will be added to the base
+ address for the chip select space the NAND Flash
+ device is connected to.
+ If not set equal to 0x10.
+
+- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask
+ addresses for given chipselect.
+
+- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode
+ valid values for davinci driver:
+ - "none"
+ - "soft"
+ - "hw"
+
+- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
+
+- ti,davinci-nand-buswidth: buswidth 8 or 16.
+
+- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB
+ identifier is saved in OOB area.
+
+Nand device bindings may contain additional sub-nodes describing partitions of
+the address space. See partition.txt for more detail. The NAND Flash timing
+values must be programmed in the chip select’s node of AEMIF
+memory-controller (see Documentation/devicetree/bindings/memory-controllers/
+davinci-aemif.txt).
Example(da850 EVM ):
+
nand_cs3@...00000 {
compatible = "ti,davinci-nand";
reg = <0x62000000 0x807ff
- 0x68000000 0x8000>;
+ 0x68000000 0x8000>;
ti,davinci-chipselect = <1>;
ti,davinci-mask-ale = <0>;
ti,davinci-mask-cle = <0>;
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists