| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1388111856-1065-1-git-send-email-hayeswang@realtek.com>
Date: Fri, 27 Dec 2013 10:37:36 +0800
From: Hayes Wang <hayeswang@...ltek.com>
To: <netdev@...r.kernel.org>, <oliver@...kum.org>
CC: <nic_swsd@...ltek.com>, <linux-kernel@...r.kernel.org>,
<linux-usb@...r.kernel.org>, Hayes Wang <hayeswang@...ltek.com>
Subject: [PATCH net-next 6/6] r8152: support RTL8153
Support new chip RTL8153 which is the USB 3.0 giga ethernet adapter.
Signed-off-by: Hayes Wang <hayeswang@...ltek.com>
---
drivers/net/usb/cdc_ether.c | 10 +
drivers/net/usb/r8152.c | 615 +++++++++++++++++++++++++++++++++++++++++++-
drivers/net/usb/r815x.c | 2 +-
3 files changed, 621 insertions(+), 6 deletions(-)
diff --git a/drivers/net/usb/cdc_ether.c b/drivers/net/usb/cdc_ether.c
index 4b1c0f3..3e09887 100644
--- a/drivers/net/usb/cdc_ether.c
+++ b/drivers/net/usb/cdc_ether.c
@@ -486,6 +486,7 @@ static const struct driver_info wwan_info = {
#define ZTE_VENDOR_ID 0x19D2
#define DELL_VENDOR_ID 0x413C
#define REALTEK_VENDOR_ID 0x0bda
+#define VENDOR_ID_SAMSUNG 0x04e8
static const struct usb_device_id products[] = {
/* BLACKLIST !!
@@ -652,6 +653,15 @@ static const struct usb_device_id products[] = {
.driver_info = 0,
},
+#if defined(CONFIG_USB_RTL8152) || defined(CONFIG_USB_RTL8152_MODULE)
+/* Samsung USB Ethernet Adapters */
+{
+ USB_DEVICE_AND_INTERFACE_INFO(VENDOR_ID_SAMSUNG, 0xa101, USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET, USB_CDC_PROTO_NONE),
+ .driver_info = 0,
+},
+#endif
+
/* WHITELIST!!!
*
* CDC Ether uses two interfaces, not necessarily consecutive.
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index 5777737..bc226e9 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -24,7 +24,7 @@
#include <linux/ipv6.h>
/* Version Information */
-#define DRIVER_VERSION "v1.02.0 (2013/10/28)"
+#define DRIVER_VERSION "v1.03.0 (2013/12/26)"
#define DRIVER_AUTHOR "Realtek linux nic maintainers <nic_swsd@...ltek.com>"
#define DRIVER_DESC "Realtek RTL8152 Based USB 2.0 Ethernet Adapters"
#define MODULENAME "r8152"
@@ -39,15 +39,24 @@
#define PLA_RXFIFO_CTRL2 0xc0a8
#define PLA_FMC 0xc0b4
#define PLA_CFG_WOL 0xc0b6
+#define PLA_TEREDO_CFG 0xc0bc
#define PLA_MAR 0xcd00
+#define PLA_BACKUP 0xd000
#define PAL_BDC_CR 0xd1a0
+#define PLA_TEREDO_TIMER 0xd2cc
+#define PLA_REALWOW_TIMER 0xd2e8
#define PLA_LEDSEL 0xdd90
#define PLA_LED_FEATURE 0xdd92
#define PLA_PHYAR 0xde00
+#define PLA_BOOT_CTRL 0xe004
#define PLA_GPHY_INTR_IMR 0xe022
#define PLA_EEE_CR 0xe040
#define PLA_EEEP_CR 0xe080
#define PLA_MAC_PWR_CTRL 0xe0c0
+#define PLA_MAC_PWR_CTRL2 0xe0ca
+#define PLA_MAC_PWR_CTRL3 0xe0cc
+#define PLA_MAC_PWR_CTRL4 0xe0ce
+#define PLA_WDT6_CTRL 0xe428
#define PLA_TCR0 0xe610
#define PLA_TCR1 0xe612
#define PLA_TXFIFO_CTRL 0xe618
@@ -73,16 +82,25 @@
#define PLA_BP_5 0xfc32
#define PLA_BP_6 0xfc34
#define PLA_BP_7 0xfc36
+#define PLA_BP_EN 0xfc38
+#define USB_U2P3_CTRL 0xb460
#define USB_DEV_STAT 0xb808
#define USB_USB_CTRL 0xd406
#define USB_PHY_CTRL 0xd408
#define USB_TX_AGG 0xd40a
#define USB_RX_BUF_TH 0xd40c
#define USB_USB_TIMER 0xd428
+#define USB_RX_EARLY_AGG 0xd42c
#define USB_PM_CTRL_STATUS 0xd432
#define USB_TX_DMA 0xd434
+#define USB_TOLERANCE 0xd490
+#define USB_LPM_CTRL 0xd41a
#define USB_UPS_CTRL 0xd800
+#define USB_MISC_0 0xd81a
+#define USB_POWER_CUT 0xd80a
+#define USB_AFE_CTRL2 0xd824
+#define USB_WDT11_CTRL 0xe43c
#define USB_BP_BA 0xfc26
#define USB_BP_0 0xfc28
#define USB_BP_1 0xfc2a
@@ -92,6 +110,7 @@
#define USB_BP_5 0xfc32
#define USB_BP_6 0xfc34
#define USB_BP_7 0xfc36
+#define USB_BP_EN 0xfc38
/* OCP Registers */
#define OCP_ALDPS_CONFIG 0x2010
@@ -101,6 +120,20 @@
#define OCP_BASE_MII 0xa400
#define OCP_EEE_AR 0xa41a
#define OCP_EEE_DATA 0xa41c
+#define OCP_PHY_STATUS 0xa420
+#define OCP_POWER_CFG 0xa430
+#define OCP_EEE_CFG 0xa432
+#define OCP_SRAM_ADDR 0xa436
+#define OCP_SRAM_DATA 0xa438
+#define OCP_DOWN_SPEED 0xa442
+#define OCP_EEE_CFG2 0xa5d0
+#define OCP_ADC_CFG 0xbc06
+
+/* SRAM Register */
+#define SRAM_LPF_CFG 0x8012
+#define SRAM_10M_AMP1 0x8080
+#define SRAM_10M_AMP2 0x8082
+#define SRAM_IMPEDANCE 0x8084
/* PLA_RCR */
#define RCR_AAP 0x00000001
@@ -117,14 +150,17 @@
#define RXFIFO_THR2_FULL 0x00000060
#define RXFIFO_THR2_HIGH 0x00000038
#define RXFIFO_THR2_OOB 0x0000004a
+#define RXFIFO_THR2_NORMAL 0x00a0
/* PLA_RXFIFO_CTRL2 */
#define RXFIFO_THR3_FULL 0x00000078
#define RXFIFO_THR3_HIGH 0x00000048
#define RXFIFO_THR3_OOB 0x0000005a
+#define RXFIFO_THR3_NORMAL 0x0110
/* PLA_TXFIFO_CTRL */
#define TXFIFO_THR_NORMAL 0x00400008
+#define TXFIFO_THR_NORMAL2 0x01000008
/* PLA_FMC */
#define FMC_FCR_MCU_EN 0x0001
@@ -132,6 +168,9 @@
/* PLA_EEEP_CR */
#define EEEP_CR_EEEP_TX 0x0002
+/* PLA_WDT6_CTRL */
+#define WDT6_SET_MODE 0x0010
+
/* PLA_TCR0 */
#define TCR0_TX_EMPTY 0x0800
#define TCR0_AUTO_FIFO 0x0080
@@ -169,6 +208,12 @@
/* PLA_CFG_WOL */
#define MAGIC_EN 0x0001
+/* PLA_TEREDO_CFG */
+#define TEREDO_SEL 0x8000
+#define TEREDO_WAKE_MASK 0x7f00
+#define TEREDO_RS_EVENT_MASK 0x00fe
+#define OOB_TEREDO_EN 0x0001
+
/* PAL_BDC_CR */
#define ALDPS_PROXY_MODE 0x0001
@@ -186,6 +231,25 @@
#define D3_CLK_GATED_EN 0x00004000
#define MCU_CLK_RATIO 0x07010f07
#define MCU_CLK_RATIO_MASK 0x0f0f0f0f
+#define ALDPS_SPDWN_RATIO 0x0f87
+
+/* PLA_MAC_PWR_CTRL2 */
+#define EEE_SPDWN_RATIO 0x8007
+
+/* PLA_MAC_PWR_CTRL3 */
+#define PKT_AVAIL_SPDWN_EN 0x0100
+#define SUSPEND_SPDWN_EN 0x0004
+#define U1U2_SPDWN_EN 0x0002
+#define L1_SPDWN_EN 0x0001
+
+/* PLA_MAC_PWR_CTRL4 */
+#define PWRSAVE_SPDWN_EN 0x1000
+#define RXDV_SPDWN_EN 0x0800
+#define TX10MIDLE_EN 0x0100
+#define TP100_SPDWN_EN 0x0020
+#define TP500_SPDWN_EN 0x0010
+#define TP1000_SPDWN_EN 0x0008
+#define EEE_SPDWN_EN 0x0001
/* PLA_GPHY_INTR_IMR */
#define GPHY_STS_MSK 0x0001
@@ -200,6 +264,9 @@
#define EEE_RX_EN 0x0001
#define EEE_TX_EN 0x0002
+/* PLA_BOOT_CTRL */
+#define AUTOLOAD_DONE 0x0002
+
/* USB_DEV_STAT */
#define STAT_SPEED_MASK 0x0006
#define STAT_SPEED_HIGH 0x0000
@@ -209,7 +276,9 @@
#define TX_AGG_MAX_THRESHOLD 0x03
/* USB_RX_BUF_TH */
+#define RX_THR_SUPPER 0x0c350180
#define RX_THR_HIGH 0x7a120180
+#define RX_THR_SLOW 0xffff0180
/* USB_TX_DMA */
#define TEST_MODE_DISABLE 0x00000001
@@ -224,12 +293,50 @@
/* USB_USB_CTRL */
#define RX_AGG_DISABLE 0x0010
+/* USB_U2P3_CTRL */
+#define U2P3_ENABLE 0x0001
+
+/* USB_POWER_CUT */
+#define PWR_EN 0x0001
+#define PHASE2_EN 0x0008
+
+/* USB_MISC_0 */
+#define PCUT_STATUS 0x0001
+
+/* USB_RX_EARLY_AGG */
+#define EARLY_AGG_SUPPER 0x0e832981
+#define EARLY_AGG_HIGH 0x0e837a12
+#define EARLY_AGG_SLOW 0x0e83ffff
+
+/* USB_WDT11_CTRL */
+#define TIMER11_EN 0x0001
+
+/* USB_LPM_CTRL */
+#define LPM_TIMER_MASK 0x0c
+#define LPM_TIMER_500MS 0x04 /* 500 ms */
+#define LPM_TIMER_500US 0x0c /* 500 us */
+
+/* USB_AFE_CTRL2 */
+#define SEN_VAL_MASK 0xf800
+#define SEN_VAL_NORMAL 0xa000
+#define SEL_RXIDLE 0x0100
+
/* OCP_ALDPS_CONFIG */
#define ENPWRSAVE 0x8000
#define ENPDNPS 0x0200
#define LINKENA 0x0100
#define DIS_SDSAVE 0x0010
+/* OCP_PHY_STATUS */
+#define PHY_STAT_MASK 0x0007
+#define PHY_STAT_LAN_ON 3
+#define PHY_STAT_PWRDN 5
+
+/* OCP_POWER_CFG */
+#define EEE_CLKDIV_EN 0x8000
+#define EN_ALDPS 0x0004
+#define EN_10M_PLLOFF 0x0001
+
/* OCP_EEE_CONFIG1 */
#define RG_TXLPI_MSK_HFDUP 0x8000
#define RG_MATCLR_EN 0x4000
@@ -264,7 +371,36 @@
#define EEE_ADDR 0x003C
#define EEE_DATA 0x0002
+/* OCP_EEE_CFG */
+#define CTAP_SHORT_EN 0x0040
+#define EEE10_EN 0x0010
+
+/* OCP_DOWN_SPEED */
+#define EN_10M_BGOFF 0x0080
+
+/* OCP_EEE_CFG2 */
+#define MY1000_EEE 0x0004
+#define MY100_EEE 0x0002
+
+/* OCP_ADC_CFG */
+#define CKADSEL_L 0x0100
+#define ADC_EN 0x0080
+#define EN_EMI_L 0x0040
+
+/* SRAM_LPF_CFG */
+#define LPF_AUTO_TUNE 0x8000
+
+/* SRAM_10M_AMP1 */
+#define GDAC_IB_UPALL 0x0008
+
+/* SRAM_10M_AMP2 */
+#define AMP_DN 0x0200
+
+/* SRAM_IMPEDANCE */
+#define RX_DRIVING_MASK 0x6000
+
enum rtl_register_content {
+ _1000bps = 0x10,
_100bps = 0x08,
_10bps = 0x04,
LINK_STATUS = 0x02,
@@ -306,6 +442,10 @@ enum rtl8152_flags {
/* Define these values to match your device */
#define VENDOR_ID_REALTEK 0x0bda
#define PRODUCT_ID_RTL8152 0x8152
+#define PRODUCT_ID_RTL8153 0x8153
+
+#define VENDOR_ID_SAMSUNG 0x04e8
+#define PRODUCT_ID_SAMSUNG 0xa101
#define MCU_TYPE_PLA 0x0100
#define MCU_TYPE_USB 0x0000
@@ -388,7 +528,11 @@ struct r8152 {
enum rtl_version {
RTL_VER_UNKNOWN = 0,
RTL_VER_01,
- RTL_VER_02
+ RTL_VER_02,
+ RTL_VER_03,
+ RTL_VER_04,
+ RTL_VER_05,
+ RTL_VER_MAX
};
/* Maximum number of multicast addresses to filter (vs. Rx-all-multicast).
@@ -704,6 +848,18 @@ static inline int r8152_mdio_read(struct r8152 *tp, u32 reg_addr)
return ocp_reg_read(tp, OCP_BASE_MII + reg_addr * 2);
}
+static void sram_write(struct r8152 *tp, u16 addr, u16 data)
+{
+ ocp_reg_write(tp, OCP_SRAM_ADDR, addr);
+ ocp_reg_write(tp, OCP_SRAM_DATA, data);
+}
+
+static u16 sram_read(struct r8152 *tp, u16 addr)
+{
+ ocp_reg_write(tp, OCP_SRAM_ADDR, addr);
+ return ocp_reg_read(tp, OCP_SRAM_DATA);
+}
+
static int read_mii_word(struct net_device *netdev, int phy_id, int reg)
{
struct r8152 *tp = netdev_priv(netdev);
@@ -1497,6 +1653,39 @@ static int rtl8152_enable(struct r8152 *tp)
return rtl_enable(tp);
}
+static void r8153_set_rx_agg(struct r8152 *tp)
+{
+ u8 speed;
+
+ speed = rtl8152_get_speed(tp);
+ if (speed & _1000bps) {
+ if (tp->udev->speed == USB_SPEED_SUPER) {
+ ocp_write_dword(tp, MCU_TYPE_USB, USB_RX_BUF_TH,
+ RX_THR_SUPPER);
+ ocp_write_dword(tp, MCU_TYPE_USB, USB_RX_EARLY_AGG,
+ EARLY_AGG_SUPPER);
+ } else {
+ ocp_write_dword(tp, MCU_TYPE_USB, USB_RX_BUF_TH,
+ RX_THR_HIGH);
+ ocp_write_dword(tp, MCU_TYPE_USB, USB_RX_EARLY_AGG,
+ EARLY_AGG_HIGH);
+ }
+ } else {
+ ocp_write_dword(tp, MCU_TYPE_USB, USB_RX_BUF_TH, RX_THR_SLOW);
+ ocp_write_dword(tp, MCU_TYPE_USB, USB_RX_EARLY_AGG,
+ EARLY_AGG_SLOW);
+ }
+}
+
+static int rtl8153_enable(struct r8152 *tp)
+{
+ set_tx_qlen(tp);
+ rtl_set_eee_plus(tp);
+ r8153_set_rx_agg(tp);
+
+ return rtl_enable(tp);
+}
+
static void rtl8152_disable(struct r8152 *tp)
{
struct net_device_stats *stats = rtl8152_get_stats(tp->netdev);
@@ -1695,15 +1884,269 @@ static inline void r8152b_enable_aldps(struct r8152 *tp)
LINKENA | DIS_SDSAVE);
}
+static void r8153_hw_phy_cfg(struct r8152 *tp)
+{
+ u32 ocp_data;
+ u16 data;
+
+ ocp_reg_write(tp, OCP_ADC_CFG, CKADSEL_L | ADC_EN | EN_EMI_L);
+ r8152_mdio_write(tp, MII_BMCR, BMCR_ANENABLE);
+
+ if (tp->version == RTL_VER_03) {
+ data = ocp_reg_read(tp, OCP_EEE_CFG);
+ data &= ~CTAP_SHORT_EN;
+ ocp_reg_write(tp, OCP_EEE_CFG, data);
+ }
+
+ data = ocp_reg_read(tp, OCP_POWER_CFG);
+ data |= EEE_CLKDIV_EN;
+ ocp_reg_write(tp, OCP_POWER_CFG, data);
+
+ data = ocp_reg_read(tp, OCP_DOWN_SPEED);
+ data |= EN_10M_BGOFF;
+ ocp_reg_write(tp, OCP_DOWN_SPEED, data);
+ data = ocp_reg_read(tp, OCP_POWER_CFG);
+ data |= EN_10M_PLLOFF;
+ ocp_reg_write(tp, OCP_POWER_CFG, data);
+ data = sram_read(tp, SRAM_IMPEDANCE);
+ data &= ~RX_DRIVING_MASK;
+ sram_write(tp, SRAM_IMPEDANCE, data);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_PHY_PWR);
+ ocp_data |= PFM_PWM_SWITCH;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_PHY_PWR, ocp_data);
+
+ data = sram_read(tp, SRAM_LPF_CFG);
+ data |= LPF_AUTO_TUNE;
+ sram_write(tp, SRAM_LPF_CFG, data);
+
+ data = sram_read(tp, SRAM_10M_AMP1);
+ data |= GDAC_IB_UPALL;
+ sram_write(tp, SRAM_10M_AMP1, data);
+ data = sram_read(tp, SRAM_10M_AMP2);
+ data |= AMP_DN;
+ sram_write(tp, SRAM_10M_AMP2, data);
+}
+
+static void r8153_u1u2en(struct r8152 *tp, int enable)
+{
+ u8 u1u2[8];
+
+ if (enable)
+ memset(u1u2, 0xff, sizeof(u1u2));
+ else
+ memset(u1u2, 0x00, sizeof(u1u2));
+
+ usb_ocp_write(tp, USB_TOLERANCE, BYTE_EN_SIX_BYTES, sizeof(u1u2), u1u2);
+}
+
+static void r8153_u2p3en(struct r8152 *tp, int enable)
+{
+ u32 ocp_data;
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_U2P3_CTRL);
+ if (enable)
+ ocp_data |= U2P3_ENABLE;
+ else
+ ocp_data &= ~U2P3_ENABLE;
+ ocp_write_word(tp, MCU_TYPE_USB, USB_U2P3_CTRL, ocp_data);
+}
+
+static void r8153_power_cut_en(struct r8152 *tp, int enable)
+{
+ u32 ocp_data;
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_POWER_CUT);
+ if (enable)
+ ocp_data |= PWR_EN | PHASE2_EN;
+ else
+ ocp_data &= ~(PWR_EN | PHASE2_EN);
+ ocp_write_word(tp, MCU_TYPE_USB, USB_POWER_CUT, ocp_data);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_MISC_0);
+ ocp_data &= ~PCUT_STATUS;
+ ocp_write_word(tp, MCU_TYPE_USB, USB_MISC_0, ocp_data);
+}
+
+static void r8153_teredo_off(struct r8152 *tp)
+{
+ u32 ocp_data;
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG);
+ ocp_data &= ~(TEREDO_SEL | TEREDO_RS_EVENT_MASK | OOB_TEREDO_EN);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG, ocp_data);
+
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_WDT6_CTRL, WDT6_SET_MODE);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_REALWOW_TIMER, 0);
+ ocp_write_dword(tp, MCU_TYPE_PLA, PLA_TEREDO_TIMER, 0);
+}
+
+static void r8153_first_init(struct r8152 *tp)
+{
+ u32 ocp_data;
+ int i;
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_MISC_1);
+ ocp_data |= RXDY_GATED_EN;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_MISC_1, ocp_data);
+
+ r8153_teredo_off(tp);
+
+ ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR);
+ ocp_data &= ~RCR_ACPT_ALL;
+ ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data);
+
+ r8153_hw_phy_cfg(tp);
+
+ rtl8152_nic_reset(tp);
+
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
+ ocp_data &= ~NOW_IS_OOB;
+ ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7);
+ ocp_data &= ~MCU_BORW_EN;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data);
+
+ for (i = 0; i < 1000; i++) {
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
+ if (ocp_data & LINK_LIST_READY)
+ break;
+ mdelay(1);
+ }
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7);
+ ocp_data |= RE_INIT_LL;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data);
+
+ for (i = 0; i < 1000; i++) {
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
+ if (ocp_data & LINK_LIST_READY)
+ break;
+ mdelay(1);
+ }
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CPCR);
+ ocp_data &= ~CPCR_RX_VLAN;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_CPCR, ocp_data);
+
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, RTL8152_RMS);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TCR0);
+ ocp_data |= TCR0_AUTO_FIFO;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_TCR0, ocp_data);
+
+ rtl8152_nic_reset(tp);
+
+ /* rx share fifo credit full threshold */
+ ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL0, RXFIFO_THR1_NORMAL);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL1, RXFIFO_THR2_NORMAL);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL2, RXFIFO_THR3_NORMAL);
+ /* TX share fifo free credit full threshold */
+ ocp_write_dword(tp, MCU_TYPE_PLA, PLA_TXFIFO_CTRL, TXFIFO_THR_NORMAL2);
+
+ // rx aggregation
+ ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_USB_CTRL);
+ ocp_data &= ~RX_AGG_DISABLE;
+ ocp_write_word(tp, MCU_TYPE_USB, USB_USB_CTRL, ocp_data);
+}
+
+static void r8153_enter_oob(struct r8152 *tp)
+{
+ u32 ocp_data;
+ int i;
+
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
+ ocp_data &= ~NOW_IS_OOB;
+ ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data);
+
+ rtl8152_disable(tp);
+
+ for (i = 0; i < 1000; i++) {
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
+ if (ocp_data & LINK_LIST_READY)
+ break;
+ mdelay(1);
+ }
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7);
+ ocp_data |= RE_INIT_LL;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data);
+
+ for (i = 0; i < 1000; i++) {
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
+ if (ocp_data & LINK_LIST_READY)
+ break;
+ mdelay(1);
+ }
+
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, RTL8152_RMS);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CFG_WOL);
+ ocp_data |= MAGIC_EN;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_CFG_WOL, ocp_data);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG);
+ ocp_data &= ~TEREDO_WAKE_MASK;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG, ocp_data);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CPCR);
+ ocp_data |= CPCR_RX_VLAN;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_CPCR, ocp_data);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PAL_BDC_CR);
+ ocp_data |= ALDPS_PROXY_MODE;
+ ocp_write_word(tp, MCU_TYPE_PLA, PAL_BDC_CR, ocp_data);
+
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
+ ocp_data |= NOW_IS_OOB | DIS_MCU_CLROOB;
+ ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data);
+
+ ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CONFIG5, LAN_WAKE_EN);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_MISC_1);
+ ocp_data &= ~RXDY_GATED_EN;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_MISC_1, ocp_data);
+
+ ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR);
+ ocp_data |= RCR_APM | RCR_AM | RCR_AB;
+ ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data);
+}
+
+static void r8153_disable_aldps(struct r8152 *tp)
+{
+ u16 data;
+
+ data = ocp_reg_read(tp, OCP_POWER_CFG);
+ data &= ~EN_ALDPS;
+ ocp_reg_write(tp, OCP_POWER_CFG, data);
+ msleep(20);
+}
+
+static void r8153_enable_aldps(struct r8152 *tp)
+{
+ u16 data;
+
+ data = ocp_reg_read(tp, OCP_POWER_CFG);
+ data |= EN_ALDPS;
+ ocp_reg_write(tp, OCP_POWER_CFG, data);
+}
+
static int rtl8152_set_speed(struct r8152 *tp, u8 autoneg, u16 speed, u8 duplex)
{
- u16 bmcr, anar;
+ u16 bmcr, anar, gbcr;
int ret = 0;
cancel_delayed_work_sync(&tp->schedule);
anar = r8152_mdio_read(tp, MII_ADVERTISE);
anar &= ~(ADVERTISE_10HALF | ADVERTISE_10FULL |
ADVERTISE_100HALF | ADVERTISE_100FULL);
+ if (tp->mii.supports_gmii) {
+ gbcr = r8152_mdio_read(tp, MII_CTRL1000);
+ gbcr &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
+ } else {
+ gbcr = 0;
+ }
if (autoneg == AUTONEG_DISABLE) {
if (speed == SPEED_10) {
@@ -1712,6 +2155,9 @@ static int rtl8152_set_speed(struct r8152 *tp, u8 autoneg, u16 speed, u8 duplex)
} else if (speed == SPEED_100) {
bmcr = BMCR_SPEED100;
anar |= ADVERTISE_100HALF | ADVERTISE_100FULL;
+ } else if (speed == SPEED_1000 && tp->mii.supports_gmii) {
+ bmcr = BMCR_SPEED1000;
+ gbcr |= ADVERTISE_1000FULL | ADVERTISE_1000HALF;
} else {
ret = -EINVAL;
goto out;
@@ -1733,6 +2179,16 @@ static int rtl8152_set_speed(struct r8152 *tp, u8 autoneg, u16 speed, u8 duplex)
anar |= ADVERTISE_10HALF;
anar |= ADVERTISE_100HALF;
}
+ } else if (speed == SPEED_1000 && tp->mii.supports_gmii) {
+ if (duplex == DUPLEX_FULL) {
+ anar |= ADVERTISE_10HALF | ADVERTISE_10FULL;
+ anar |= ADVERTISE_100HALF | ADVERTISE_100FULL;
+ gbcr |= ADVERTISE_1000FULL | ADVERTISE_1000HALF;
+ } else {
+ anar |= ADVERTISE_10HALF;
+ anar |= ADVERTISE_100HALF;
+ gbcr |= ADVERTISE_1000HALF;
+ }
} else {
ret = -EINVAL;
goto out;
@@ -1741,6 +2197,9 @@ static int rtl8152_set_speed(struct r8152 *tp, u8 autoneg, u16 speed, u8 duplex)
bmcr = BMCR_ANENABLE | BMCR_ANRESTART;
}
+ if (tp->mii.supports_gmii)
+ r8152_mdio_write(tp, MII_CTRL1000, gbcr);
+
r8152_mdio_write(tp, MII_ADVERTISE, anar);
r8152_mdio_write(tp, MII_BMCR, bmcr);
@@ -1762,6 +2221,15 @@ static void rtl8152_down(struct r8152 *tp)
r8152b_enable_aldps(tp);
}
+static void rtl8153_down(struct r8152 *tp)
+{
+ r8153_u1u2en(tp, 0);
+ r8153_power_cut_en(tp, 0);
+ r8153_disable_aldps(tp);
+ r8153_enter_oob(tp);
+ r8153_enable_aldps(tp);
+}
+
static void set_carrier(struct r8152 *tp)
{
struct net_device *netdev = tp->netdev;
@@ -1821,7 +2289,9 @@ static int rtl8152_open(struct net_device *netdev)
return res;
}
- rtl8152_set_speed(tp, AUTONEG_ENABLE, SPEED_100, DUPLEX_FULL);
+ rtl8152_set_speed(tp, AUTONEG_ENABLE,
+ tp->mii.supports_gmii ? SPEED_1000 : SPEED_100,
+ DUPLEX_FULL);
tp->speed = 0;
netif_carrier_off(netdev);
netif_start_queue(netdev);
@@ -1861,6 +2331,13 @@ static void rtl_clear_bp(struct r8152 *tp)
ocp_write_word(tp, MCU_TYPE_USB, USB_BP_BA, 0);
}
+static void r8153_clear_bp(struct r8152 *tp)
+{
+ ocp_write_byte(tp, MCU_TYPE_PLA, PLA_BP_EN, 0);
+ ocp_write_byte(tp, MCU_TYPE_USB, USB_BP_EN, 0);
+ rtl_clear_bp(tp);
+}
+
static void r8152b_enable_eee(struct r8152 *tp)
{
u32 ocp_data;
@@ -1884,6 +2361,22 @@ static void r8152b_enable_eee(struct r8152 *tp)
ocp_reg_write(tp, OCP_EEE_AR, 0x0000);
}
+static void r8153_enable_eee(struct r8152 *tp)
+{
+ u32 ocp_data;
+ u16 data;
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR);
+ ocp_data |= EEE_RX_EN | EEE_TX_EN;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEE_CR, ocp_data);
+ data = ocp_reg_read(tp, OCP_EEE_CFG);
+ data |= EEE10_EN;
+ ocp_reg_write(tp, OCP_EEE_CFG, data);
+ data = ocp_reg_read(tp, OCP_EEE_CFG2);
+ data |= MY1000_EEE | MY100_EEE;
+ ocp_reg_write(tp, OCP_EEE_CFG2, data);
+}
+
static void r8152b_enable_fc(struct r8152 *tp)
{
u16 anar;
@@ -1953,6 +2446,75 @@ static void r8152b_init(struct r8152 *tp)
ocp_write_word(tp, MCU_TYPE_USB, USB_USB_CTRL, ocp_data);
}
+static void r8153_init(struct r8152 *tp)
+{
+ u32 ocp_data;
+ int i;
+
+ r8153_u1u2en(tp, 0);
+
+ for (i = 0; i < 500; i++) {
+ if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
+ AUTOLOAD_DONE)
+ break;
+ msleep(20);
+ }
+
+ for (i = 0; i < 500; i++) {
+ ocp_data = ocp_reg_read(tp, OCP_PHY_STATUS) & PHY_STAT_MASK;
+ if (ocp_data == PHY_STAT_LAN_ON || ocp_data == PHY_STAT_PWRDN)
+ break;
+ msleep(20);
+ }
+
+ r8153_u2p3en(tp, 0);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_WDT11_CTRL);
+ ocp_data &= ~TIMER11_EN;
+ ocp_write_word(tp, MCU_TYPE_USB, USB_WDT11_CTRL, ocp_data);
+
+ r8153_clear_bp(tp);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_LED_FEATURE);
+ ocp_data &= ~LED_MODE_MASK;
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_LED_FEATURE, ocp_data);
+
+ ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_LPM_CTRL);
+ ocp_data &= ~LPM_TIMER_MASK;
+ if (tp->udev->speed == USB_SPEED_SUPER)
+ ocp_data |= LPM_TIMER_500US;
+ else
+ ocp_data |= LPM_TIMER_500MS;
+ ocp_write_byte(tp, MCU_TYPE_USB, USB_LPM_CTRL, ocp_data);
+
+ ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_AFE_CTRL2);
+ ocp_data &= ~SEN_VAL_MASK;
+ ocp_data |= SEN_VAL_NORMAL | SEL_RXIDLE;
+ ocp_write_word(tp, MCU_TYPE_USB, USB_AFE_CTRL2, ocp_data);
+
+ r8153_power_cut_en(tp, 0);
+ r8153_u1u2en(tp, 1);
+
+ r8153_first_init(tp);
+
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL, ALDPS_SPDWN_RATIO);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL2, EEE_SPDWN_RATIO);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL3,
+ PKT_AVAIL_SPDWN_EN | SUSPEND_SPDWN_EN |
+ U1U2_SPDWN_EN | L1_SPDWN_EN);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL4,
+ PWRSAVE_SPDWN_EN | RXDV_SPDWN_EN | TX10MIDLE_EN |
+ TP100_SPDWN_EN | TP500_SPDWN_EN | TP1000_SPDWN_EN |
+ EEE_SPDWN_EN);
+
+ r8153_enable_eee(tp);
+ r8153_enable_aldps(tp);
+ r8152b_enable_fc(tp);
+
+ r8152_mdio_write(tp, MII_BMCR, BMCR_RESET | BMCR_ANENABLE |
+ BMCR_ANRESTART);
+}
+
static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message)
{
struct r8152 *tp = usb_get_intfdata(intf);
@@ -1978,7 +2540,9 @@ static int rtl8152_resume(struct usb_interface *intf)
tp->rtl_ops.init(tp);
netif_device_attach(tp->netdev);
if (netif_running(tp->netdev)) {
- rtl8152_set_speed(tp, AUTONEG_ENABLE, SPEED_100, DUPLEX_FULL);
+ rtl8152_set_speed(tp, AUTONEG_ENABLE,
+ tp->mii.supports_gmii ? SPEED_1000 : SPEED_100,
+ DUPLEX_FULL);
tp->speed = 0;
netif_carrier_off(tp->netdev);
set_bit(WORK_ENABLE, &tp->flags);
@@ -2082,6 +2646,18 @@ static void r8152b_get_version(struct r8152 *tp)
case 0x4c10:
tp->version = RTL_VER_02;
break;
+ case 0x5c00:
+ tp->version = RTL_VER_03;
+ tp->mii.supports_gmii = 1;
+ break;
+ case 0x5c10:
+ tp->version = RTL_VER_04;
+ tp->mii.supports_gmii = 1;
+ break;
+ case 0x5c20:
+ tp->version = RTL_VER_05;
+ tp->mii.supports_gmii = 1;
+ break;
default:
netif_info(tp, probe, tp->netdev,
"Unknown version 0x%04x\n", version);
@@ -2104,6 +2680,11 @@ static void rtl8152_unload(struct r8152 *tp)
ocp_write_word(tp, MCU_TYPE_USB, USB_PM_CTRL_STATUS, ocp_data);
}
+static void rtl8153_unload(struct r8152 *tp)
+{
+ r8153_power_cut_en(tp, 1);
+}
+
static int rtl_ops_init(struct r8152 *tp, const struct usb_device_id *id)
{
struct rtl_ops *ops = &tp->rtl_ops;
@@ -2119,6 +2700,28 @@ static int rtl_ops_init(struct r8152 *tp, const struct usb_device_id *id)
ops->down = rtl8152_down;
ops->unload = rtl8152_unload;
break;
+ case PRODUCT_ID_RTL8153:
+ ops->init = r8153_init;
+ ops->enable = rtl8153_enable;
+ ops->disable = rtl8152_disable;
+ ops->down = rtl8153_down;
+ ops->unload = rtl8153_unload;
+ break;
+ default:
+ ret = -EFAULT;
+ break;
+ }
+ break;
+
+ case VENDOR_ID_SAMSUNG:
+ switch (id->idProduct) {
+ case PRODUCT_ID_SAMSUNG:
+ ops->init = r8153_init;
+ ops->enable = rtl8153_enable;
+ ops->disable = rtl8152_disable;
+ ops->down = rtl8153_down;
+ ops->unload = rtl8153_unload;
+ break;
default:
ret = -EFAULT;
break;
@@ -2226,6 +2829,8 @@ static void rtl8152_disconnect(struct usb_interface *intf)
/* table of devices that work with this driver */
static struct usb_device_id rtl8152_table[] = {
{USB_DEVICE(VENDOR_ID_REALTEK, PRODUCT_ID_RTL8152)},
+ {USB_DEVICE(VENDOR_ID_REALTEK, PRODUCT_ID_RTL8153)},
+ {USB_DEVICE(VENDOR_ID_SAMSUNG, PRODUCT_ID_SAMSUNG)},
{}
};
diff --git a/drivers/net/usb/r815x.c b/drivers/net/usb/r815x.c
index 2df2f4f..5fd2ca6 100644
--- a/drivers/net/usb/r815x.c
+++ b/drivers/net/usb/r815x.c
@@ -226,7 +226,7 @@ static const struct usb_device_id products[] = {
{
USB_DEVICE_AND_INTERFACE_INFO(REALTEK_VENDOR_ID, 0x8153, USB_CLASS_COMM,
USB_CDC_SUBCLASS_ETHERNET, USB_CDC_PROTO_NONE),
-#if defined(CONFIG_USB_RTL8153) || defined(CONFIG_USB_RTL8153_MODULE)
+#if defined(CONFIG_USB_RTL8152) || defined(CONFIG_USB_RTL8152_MODULE)
.driver_info = 0,
#else
.driver_info = (unsigned long) &r8153_info,
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists