| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5319689A.3020505@ti.com>
Date: Fri, 7 Mar 2014 12:05:06 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: Loc Ho <lho@....com>, <tj@...nel.org>
CC: <olof@...om.net>, <arnd@...db.de>, <linux-kernel@...r.kernel.org>,
<linux-scsi@...r.kernel.org>, <linux-ide@...r.kernel.org>,
<devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>, <ddutile@...hat.com>,
<jcm@...hat.com>, <patches@....com>, Tuan Phan <tphan@....com>,
Suman Tripathi <stripathi@....com>
Subject: Re: [PATCH v14 2/3] PHY: add APM X-Gene SoC 15Gbps Multi-purpose
PHY driver
Hi,
On Thursday 06 March 2014 11:24 PM, Loc Ho wrote:
> This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY.
> This is the physical layer interface for the corresponding host
> controller. Currently, only external clock and Gen3 SATA mode
> are supported.
Pls fix these checkpatch errors
ERROR: code indent should use tabs where possible
#413: FILE: drivers/phy/phy-xgene.c:293:
+ (((dst) & ~0x00000060) | (((u32) (src) << 5) &
0x00000060))$
WARNING: please, no spaces at the start of a line
#413: FILE: drivers/phy/phy-xgene.c:293:
+ (((dst) & ~0x00000060) | (((u32) (src) << 5) &
0x00000060))$
ERROR: code indent should use tabs where possible
#415: FILE: drivers/phy/phy-xgene.c:295:
+ (((dst) & ~0x00000006) | (((u32) (src) << 1) &
0x00000006))$
WARNING: please, no spaces at the start of a line
#415: FILE: drivers/phy/phy-xgene.c:295:
+ (((dst) & ~0x00000006) | (((u32) (src) << 1) &
0x00000006))$
ERROR: code indent should use tabs where possible
#685: FILE: drivers/phy/phy-xgene.c:565:
+ unsigned long deadline = jiffies + HZ;$
WARNING: please, no spaces at the start of a line
#685: FILE: drivers/phy/phy-xgene.c:565:
+ unsigned long deadline = jiffies + HZ;$
ERROR: code indent should use tabs where possible
#707: FILE: drivers/phy/phy-xgene.c:587:
+ unsigned long deadline = jiffies + HZ;$
WARNING: please, no spaces at the start of a line
#707: FILE: drivers/phy/phy-xgene.c:587:
+ unsigned long deadline = jiffies + HZ;$
ERROR: code indent should use tabs where possible
#932: FILE: drivers/phy/phy-xgene.c:812:
+ if (cmu_type == REF_CMU) {$
WARNING: please, no spaces at the start of a line
#932: FILE: drivers/phy/phy-xgene.c:812:
+ if (cmu_type == REF_CMU) {$
ERROR: code indent should use tabs where possible
#1309: FILE: drivers/phy/phy-xgene.c:1189:
+ * that is required to be calibrated.$
ERROR: code indent should use tabs where possible
#1319: FILE: drivers/phy/phy-xgene.c:1199:
+ * resistors that are required to the calibrated.$
total: 7 errors, 5 warnings, 1765 lines checked
Thanks
Kishon
>
> Signed-off-by: Loc Ho <lho@....com>
> Signed-off-by: Tuan Phan <tphan@....com>
> Signed-off-by: Suman Tripathi <stripathi@....com>
> ---
> drivers/phy/Kconfig | 7 +
> drivers/phy/Makefile | 2 +
> drivers/phy/phy-xgene.c | 1750 +++++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 1759 insertions(+), 0 deletions(-)
> create mode 100644 drivers/phy/phy-xgene.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index afa2354..221a1b7 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -64,4 +64,11 @@ config BCM_KONA_USB2_PHY
> help
> Enable this to support the Broadcom Kona USB 2.0 PHY.
>
> +config PHY_XGENE
> + tristate "APM X-Gene 15Gbps PHY support"
> + depends on HAS_IOMEM && OF && (ARM64 || COMPILE_TEST)
> + select GENERIC_PHY
> + help
> + This option enables support for APM X-Gene SoC multi-purpose PHY.
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index b57c253..dee70f4 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -9,3 +9,5 @@ obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
> +
> diff --git a/drivers/phy/phy-xgene.c b/drivers/phy/phy-xgene.c
> new file mode 100644
> index 0000000..c9b6ad8
> --- /dev/null
> +++ b/drivers/phy/phy-xgene.c
> @@ -0,0 +1,1750 @@
> +/*
> + * AppliedMicro X-Gene Multi-purpose PHY driver
> + *
> + * Copyright (c) 2014, Applied Micro Circuits Corporation
> + * Author: Loc Ho <lho@....com>
> + * Tuan Phan <tphan@....com>
> + * Suman Tripathi <stripathi@....com>
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + *
> + * The APM X-Gene PHY consists of two PLL clock macro's (CMU) and lanes.
> + * The first PLL clock macro is used for internal reference clock. The second
> + * PLL clock macro is used to generate the clock for the PHY. This driver
> + * configures the first PLL CMU, the second PLL CMU, and programs the PHY to
> + * operate according to the mode of operation. The first PLL CMU is only
> + * required if internal clock is enabled.
> + *
> + * Logical Layer Out Of HW module units:
> + *
> + * -----------------
> + * | Internal | |------|
> + * | Ref PLL CMU |----| | ------------- ---------
> + * ------------ ---- | MUX |-----|PHY PLL CMU|----| Serdes|
> + * | | | | ---------
> + * External Clock ------| | -------------
> + * |------|
> + *
> + * The Ref PLL CMU CSR (Configuration System Registers) is accessed
> + * indirectly from the SDS offset at 0x2000. It is only required for
> + * internal reference clock.
> + * The PHY PLL CMU CSR is accessed indirectly from the SDS offset at 0x0000.
> + * The Serdes CSR is accessed indirectly from the SDS offset at 0x0400.
> + *
> + * The Ref PLL CMU can be located within the same PHY IP or outside the PHY IP
> + * due to shared Ref PLL CMU. For PHY with Ref PLL CMU shared with another IP,
> + * it is located outside the PHY IP. This is the case for the PHY located
> + * at 0x1f23a000 (SATA Port 4/5). For such PHY, another resource is required
> + * to located the SDS/Ref PLL CMU module and its clock for that IP enabled.
> + *
> + * Currently, this driver only supports Gen3 SATA mode with external clock.
> + */
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/delay.h>
> +#include <linux/phy/phy.h>
> +#include <linux/clk.h>
> +
> +/* Max 2 lanes per a PHY unit */
> +#define MAX_LANE 2
> +
> +/* Register offset inside the PHY */
> +#define SERDES_PLL_INDIRECT_OFFSET 0x0000
> +#define SERDES_PLL_REF_INDIRECT_OFFSET 0x2000
> +#define SERDES_INDIRECT_OFFSET 0x0400
> +#define SERDES_LANE_STRIDE 0x0200
> +
> +/* Some default Serdes parameters */
> +#define DEFAULT_SATA_TXBOOST_GAIN { 0x1e, 0x1e, 0x1e }
> +#define DEFAULT_SATA_TXEYEDIRECTION { 0x0, 0x0, 0x0 }
> +#define DEFAULT_SATA_TXEYETUNING { 0xa, 0xa, 0xa }
> +#define DEFAULT_SATA_SPD_SEL { 0x1, 0x3, 0x7 }
> +#define DEFAULT_SATA_TXAMP { 0x8, 0x8, 0x8 }
> +#define DEFAULT_SATA_TXCN1 { 0x2, 0x2, 0x2 }
> +#define DEFAULT_SATA_TXCN2 { 0x0, 0x0, 0x0 }
> +#define DEFAULT_SATA_TXCP1 { 0xa, 0xa, 0xa }
> +
> +#define SATA_SPD_SEL_GEN3 0x7
> +#define SATA_SPD_SEL_GEN2 0x3
> +#define SATA_SPD_SEL_GEN1 0x1
> +
> +#define SSC_DISABLE 0
> +#define SSC_ENABLE 1
> +
> +#define FBDIV_VAL_50M 0x77
> +#define REFDIV_VAL_50M 0x1
> +#define FBDIV_VAL_100M 0x3B
> +#define REFDIV_VAL_100M 0x0
> +
> +/* SATA Clock/Reset CSR */
> +#define SATACLKENREG 0x00000000
> +#define SATA0_CORE_CLKEN 0x00000002
> +#define SATA1_CORE_CLKEN 0x00000004
> +#define SATASRESETREG 0x00000004
> +#define SATA_MEM_RESET_MASK 0x00000020
> +#define SATA_MEM_RESET_RD(src) (((src) & 0x00000020) >> 5)
> +#define SATA_SDS_RESET_MASK 0x00000004
> +#define SATA_CSR_RESET_MASK 0x00000001
> +#define SATA_CORE_RESET_MASK 0x00000002
> +#define SATA_PMCLK_RESET_MASK 0x00000010
> +#define SATA_PCLK_RESET_MASK 0x00000008
> +
> +/* SDS CSR used for PHY Indirect access */
> +#define SATA_ENET_SDS_PCS_CTL0 0x00000000
> +#define REGSPEC_CFG_I_TX_WORDMODE0_SET(dst, src) \
> + (((dst) & ~0x00070000) | (((u32) (src) << 16) & 0x00070000))
> +#define REGSPEC_CFG_I_RX_WORDMODE0_SET(dst, src) \
> + (((dst) & ~0x00e00000) | (((u32) (src) << 21) & 0x00e00000))
> +#define SATA_ENET_SDS_CTL0 0x0000000c
> +#define REGSPEC_CFG_I_CUSTOMER_PIN_MODE0_SET(dst, src) \
> + (((dst) & ~0x00007fff) | (((u32) (src)) & 0x00007fff))
> +#define SATA_ENET_SDS_CTL1 0x00000010
> +#define CFG_I_SPD_SEL_CDR_OVR1_SET(dst, src) \
> + (((dst) & ~0x0000000f) | (((u32) (src)) & 0x0000000f))
> +#define SATA_ENET_SDS_RST_CTL 0x00000024
> +#define SATA_ENET_SDS_IND_CMD_REG 0x0000003c
> +#define CFG_IND_WR_CMD_MASK 0x00000001
> +#define CFG_IND_RD_CMD_MASK 0x00000002
> +#define CFG_IND_CMD_DONE_MASK 0x00000004
> +#define CFG_IND_ADDR_SET(dst, src) \
> + (((dst) & ~0x003ffff0) | (((u32) (src) << 4) & 0x003ffff0))
> +#define SATA_ENET_SDS_IND_RDATA_REG 0x00000040
> +#define SATA_ENET_SDS_IND_WDATA_REG 0x00000044
> +#define SATA_ENET_CLK_MACRO_REG 0x0000004c
> +#define I_RESET_B_SET(dst, src) \
> + (((dst) & ~0x00000001) | (((u32) (src)) & 0x00000001))
> +#define I_PLL_FBDIV_SET(dst, src) \
> + (((dst) & ~0x001ff000) | (((u32) (src) << 12) & 0x001ff000))
> +#define I_CUSTOMEROV_SET(dst, src) \
> + (((dst) & ~0x00000f80) | (((u32) (src) << 7) & 0x00000f80))
> +#define O_PLL_LOCK_RD(src) (((src) & 0x40000000) >> 30)
> +#define O_PLL_READY_RD(src) (((src) & 0x80000000) >> 31)
> +
> +/* PLL Clock Macro Unit (CMU) CSR accessing from SDS indirectly */
> +#define CMU_REG0 0x00000
> +#define CMU_REG0_PLL_REF_SEL_MASK 0x00002000
> +#define CMU_REG0_PLL_REF_SEL_SET(dst, src) \
> + (((dst) & ~0x00002000) | (((u32) (src) << 13) & 0x00002000))
> +#define CMU_REG0_PDOWN_MASK 0x00004000
> +#define CMU_REG0_CAL_COUNT_RESOL_SET(dst, src) \
> + (((dst) & ~0x000000e0) | (((u32) (src) << 5) & 0x000000e0))
> +#define CMU_REG1 0x00002
> +#define CMU_REG1_PLL_CP_SET(dst, src) \
> + (((dst) & ~0x00003c00) | (((u32) (src) << 10) & 0x00003c00))
> +#define CMU_REG1_PLL_MANUALCAL_SET(dst, src) \
> + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
> +#define CMU_REG1_PLL_CP_SEL_SET(dst, src) \
> + (((dst) & ~0x000003e0) | (((u32) (src) << 5) & 0x000003e0))
> +#define CMU_REG1_REFCLK_CMOS_SEL_MASK 0x00000001
> +#define CMU_REG1_REFCLK_CMOS_SEL_SET(dst, src) \
> + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
> +#define CMU_REG2 0x00004
> +#define CMU_REG2_PLL_REFDIV_SET(dst, src) \
> + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
> +#define CMU_REG2_PLL_LFRES_SET(dst, src) \
> + (((dst) & ~0x0000001e) | (((u32) (src) << 1) & 0x0000001e))
> +#define CMU_REG2_PLL_FBDIV_SET(dst, src) \
> + (((dst) & ~0x00003fe0) | (((u32) (src) << 5) & 0x00003fe0))
> +#define CMU_REG3 0x00006
> +#define CMU_REG3_VCOVARSEL_SET(dst, src) \
> + (((dst) & ~0x0000000f) | (((u32) (src) << 0) & 0x0000000f))
> +#define CMU_REG3_VCO_MOMSEL_INIT_SET(dst, src) \
> + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
> +#define CMU_REG3_VCO_MANMOMSEL_SET(dst, src) \
> + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
> +#define CMU_REG4 0x00008
> +#define CMU_REG5 0x0000a
> +#define CMU_REG5_PLL_LFSMCAP_SET(dst, src) \
> + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
> +#define CMU_REG5_PLL_LOCK_RESOLUTION_SET(dst, src) \
> + (((dst) & ~0x0000000e) | (((u32) (src) << 1) & 0x0000000e))
> +#define CMU_REG5_PLL_LFCAP_SET(dst, src) \
> + (((dst) & ~0x00003000) | (((u32) (src) << 12) & 0x00003000))
> +#define CMU_REG5_PLL_RESETB_MASK 0x00000001
> +#define CMU_REG6 0x0000c
> +#define CMU_REG6_PLL_VREGTRIM_SET(dst, src) \
> + (((dst) & ~0x00000600) | (((u32) (src) << 9) & 0x00000600))
> +#define CMU_REG6_MAN_PVT_CAL_SET(dst, src) \
> + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
> +#define CMU_REG7 0x0000e
> +#define CMU_REG7_PLL_CALIB_DONE_RD(src) ((0x00004000 & (u32) (src)) >> 14)
> +#define CMU_REG7_VCO_CAL_FAIL_RD(src) ((0x00000c00 & (u32) (src)) >> 10)
> +#define CMU_REG8 0x00010
> +#define CMU_REG9 0x00012
> +#define CMU_REG9_WORD_LEN_8BIT 0x000
> +#define CMU_REG9_WORD_LEN_10BIT 0x001
> +#define CMU_REG9_WORD_LEN_16BIT 0x002
> +#define CMU_REG9_WORD_LEN_20BIT 0x003
> +#define CMU_REG9_WORD_LEN_32BIT 0x004
> +#define CMU_REG9_WORD_LEN_40BIT 0x005
> +#define CMU_REG9_WORD_LEN_64BIT 0x006
> +#define CMU_REG9_WORD_LEN_66BIT 0x007
> +#define CMU_REG9_TX_WORD_MODE_CH1_SET(dst, src) \
> + (((dst) & ~0x00000380) | (((u32) (src) << 7) & 0x00000380))
> +#define CMU_REG9_TX_WORD_MODE_CH0_SET(dst, src) \
> + (((dst) & ~0x00000070) | (((u32) (src) << 4) & 0x00000070))
> +#define CMU_REG9_PLL_POST_DIVBY2_SET(dst, src) \
> + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
> +#define CMU_REG9_VBG_BYPASSB_SET(dst, src) \
> + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
> +#define CMU_REG9_IGEN_BYPASS_SET(dst, src) \
> + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
> +#define CMU_REG10 0x00014
> +#define CMU_REG10_VREG_REFSEL_SET(dst, src) \
> + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
> +#define CMU_REG11 0x00016
> +#define CMU_REG12 0x00018
> +#define CMU_REG12_STATE_DELAY9_SET(dst, src) \
> + (((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0))
> +#define CMU_REG13 0x0001a
> +#define CMU_REG14 0x0001c
> +#define CMU_REG15 0x0001e
> +#define CMU_REG16 0x00020
> +#define CMU_REG16_PVT_DN_MAN_ENA_MASK 0x00000001
> +#define CMU_REG16_PVT_UP_MAN_ENA_MASK 0x00000002
> +#define CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(dst, src) \
> + (((dst) & ~0x0000001c) | (((u32) (src) << 2) & 0x0000001c))
> +#define CMU_REG16_CALIBRATION_DONE_OVERRIDE_SET(dst, src) \
> + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
> +#define CMU_REG16_BYPASS_PLL_LOCK_SET(dst, src) \
> + (((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020))
> +#define CMU_REG17 0x00022
> +#define CMU_REG17_PVT_CODE_R2A_SET(dst, src) \
> + (((dst) & ~0x00007f00) | (((u32) (src) << 8) & 0x00007f00))
> +#define CMU_REG17_RESERVED_7_SET(dst, src) \
> + (((dst) & ~0x000000e0) | (((u32) (src) << 5) & 0x000000e0))
> +#define CMU_REG17_PVT_TERM_MAN_ENA_MASK 0x00008000
> +#define CMU_REG18 0x00024
> +#define CMU_REG19 0x00026
> +#define CMU_REG20 0x00028
> +#define CMU_REG21 0x0002a
> +#define CMU_REG22 0x0002c
> +#define CMU_REG23 0x0002e
> +#define CMU_REG24 0x00030
> +#define CMU_REG25 0x00032
> +#define CMU_REG26 0x00034
> +#define CMU_REG26_FORCE_PLL_LOCK_SET(dst, src) \
> + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
> +#define CMU_REG27 0x00036
> +#define CMU_REG28 0x00038
> +#define CMU_REG29 0x0003a
> +#define CMU_REG30 0x0003c
> +#define CMU_REG30_LOCK_COUNT_SET(dst, src) \
> + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))
> +#define CMU_REG30_PCIE_MODE_SET(dst, src) \
> + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
> +#define CMU_REG31 0x0003e
> +#define CMU_REG32 0x00040
> +#define CMU_REG32_FORCE_VCOCAL_START_MASK 0x00004000
> +#define CMU_REG32_PVT_CAL_WAIT_SEL_SET(dst, src) \
> + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))
> +#define CMU_REG32_IREF_ADJ_SET(dst, src) \
> + (((dst) & ~0x00000180) | (((u32) (src) << 7) & 0x00000180))
> +#define CMU_REG33 0x00042
> +#define CMU_REG34 0x00044
> +#define CMU_REG34_VCO_CAL_VTH_LO_MAX_SET(dst, src) \
> + (((dst) & ~0x0000000f) | (((u32) (src) << 0) & 0x0000000f))
> +#define CMU_REG34_VCO_CAL_VTH_HI_MAX_SET(dst, src) \
> + (((dst) & ~0x00000f00) | (((u32) (src) << 8) & 0x00000f00))
> +#define CMU_REG34_VCO_CAL_VTH_LO_MIN_SET(dst, src) \
> + (((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0))
> +#define CMU_REG34_VCO_CAL_VTH_HI_MIN_SET(dst, src) \
> + (((dst) & ~0x0000f000) | (((u32) (src) << 12) & 0x0000f000))
> +#define CMU_REG35 0x00046
> +#define CMU_REG35_PLL_SSC_MOD_SET(dst, src) \
> + (((dst) & ~0x0000fe00) | (((u32) (src) << 9) & 0x0000fe00))
> +#define CMU_REG36 0x00048
> +#define CMU_REG36_PLL_SSC_EN_SET(dst, src) \
> + (((dst) & ~0x00000010) | (((u32) (src) << 4) & 0x00000010))
> +#define CMU_REG36_PLL_SSC_VSTEP_SET(dst, src) \
> + (((dst) & ~0x0000ffc0) | (((u32) (src) << 6) & 0x0000ffc0))
> +#define CMU_REG36_PLL_SSC_DSMSEL_SET(dst, src) \
> + (((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020))
> +#define CMU_REG37 0x0004a
> +#define CMU_REG38 0x0004c
> +#define CMU_REG39 0x0004e
> +
> +/* PHY lane CSR accessing from SDS indirectly */
> +#define RXTX_REG0 0x000
> +#define RXTX_REG0_CTLE_EQ_HR_SET(dst, src) \
> + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
> +#define RXTX_REG0_CTLE_EQ_QR_SET(dst, src) \
> + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
> +#define RXTX_REG0_CTLE_EQ_FR_SET(dst, src) \
> + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
> +#define RXTX_REG1 0x002
> +#define RXTX_REG1_RXACVCM_SET(dst, src) \
> + (((dst) & ~0x0000f000) | (((u32) (src) << 12) & 0x0000f000))
> +#define RXTX_REG1_CTLE_EQ_SET(dst, src) \
> + (((dst) & ~0x00000f80) | (((u32) (src) << 7) & 0x00000f80))
> +#define RXTX_REG1_RXVREG1_SET(dst, src) \
> + (((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060))
> +#define RXTX_REG1_RXIREF_ADJ_SET(dst, src) \
> + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))
> +#define RXTX_REG2 0x004
> +#define RXTX_REG2_VTT_ENA_SET(dst, src) \
> + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
> +#define RXTX_REG2_TX_FIFO_ENA_SET(dst, src) \
> + (((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020))
> +#define RXTX_REG2_VTT_SEL_SET(dst, src) \
> + (((dst) & ~0x000000c0) | (((u32) (src) << 6) & 0x000000c0))
> +#define RXTX_REG4 0x008
> +#define RXTX_REG4_TX_LOOPBACK_BUF_EN_MASK 0x00000040
> +#define RXTX_REG4_TX_DATA_RATE_SET(dst, src) \
> + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
> +#define RXTX_REG4_TX_WORD_MODE_SET(dst, src) \
> + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
> +#define RXTX_REG5 0x00a
> +#define RXTX_REG5_TX_CN1_SET(dst, src) \
> + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
> +#define RXTX_REG5_TX_CP1_SET(dst, src) \
> + (((dst) & ~0x000007e0) | (((u32) (src) << 5) & 0x000007e0))
> +#define RXTX_REG5_TX_CN2_SET(dst, src) \
> + (((dst) & ~0x0000001f) | (((u32) (src) << 0) & 0x0000001f))
> +#define RXTX_REG6 0x00c
> +#define RXTX_REG6_TXAMP_CNTL_SET(dst, src) \
> + (((dst) & ~0x00000780) | (((u32) (src) << 7) & 0x00000780))
> +#define RXTX_REG6_TXAMP_ENA_SET(dst, src) \
> + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
> +#define RXTX_REG6_RX_BIST_ERRCNT_RD_SET(dst, src) \
> + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
> +#define RXTX_REG6_TX_IDLE_SET(dst, src) \
> + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
> +#define RXTX_REG6_RX_BIST_RESYNC_SET(dst, src) \
> + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
> +#define RXTX_REG7 0x00e
> +#define RXTX_REG7_RESETB_RXD_MASK 0x00000100
> +#define RXTX_REG7_RESETB_RXA_MASK 0x00000080
> +#define RXTX_REG7_BIST_ENA_RX_SET(dst, src) \
> + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
> +#define RXTX_REG7_RX_WORD_MODE_SET(dst, src) \
> + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
> +#define RXTX_REG8 0x010
> +#define RXTX_REG8_CDR_LOOP_ENA_SET(dst, src) \
> + (((dst) & ~0x00004000) | (((u32) (src) << 14) & 0x00004000))
> +#define RXTX_REG8_CDR_BYPASS_RXLOS_SET(dst, src) \
> + (((dst) & ~0x00000800) | (((u32) (src) << 11) & 0x00000800))
> +#define RXTX_REG8_SSC_ENABLE_SET(dst, src) \
> + (((dst) & ~0x00000200) | (((u32) (src) << 9) & 0x00000200))
> +#define RXTX_REG8_SD_VREF_SET(dst, src) \
> + (((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0))
> +#define RXTX_REG8_SD_DISABLE_SET(dst, src) \
> + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
> +#define RXTX_REG7 0x00e
> +#define RXTX_REG7_RESETB_RXD_SET(dst, src) \
> + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
> +#define RXTX_REG7_RESETB_RXA_SET(dst, src) \
> + (((dst) & ~0x00000080) | (((u32) (src) << 7) & 0x00000080))
> +#define RXTX_REG7_LOOP_BACK_ENA_CTLE_MASK 0x00004000
> +#define RXTX_REG7_LOOP_BACK_ENA_CTLE_SET(dst, src) \
> + (((dst) & ~0x00004000) | (((u32) (src) << 14) & 0x00004000))
> +#define RXTX_REG11 0x016
> +#define RXTX_REG11_PHASE_ADJUST_LIMIT_SET(dst, src) \
> + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
> +#define RXTX_REG12 0x018
> +#define RXTX_REG12_LATCH_OFF_ENA_SET(dst, src) \
> + (((dst) & ~0x00002000) | (((u32) (src) << 13) & 0x00002000))
> +#define RXTX_REG12_SUMOS_ENABLE_SET(dst, src) \
> + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
> +#define RXTX_REG12_RX_DET_TERM_ENABLE_MASK 0x00000002
> +#define RXTX_REG12_RX_DET_TERM_ENABLE_SET(dst, src) \
> + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
> +#define RXTX_REG13 0x01a
> +#define RXTX_REG14 0x01c
> +#define RXTX_REG14_CLTE_LATCAL_MAN_PROG_SET(dst, src) \
> + (((dst) & ~0x0000003f) | (((u32) (src) << 0) & 0x0000003f))
> +#define RXTX_REG14_CTLE_LATCAL_MAN_ENA_SET(dst, src) \
> + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
> +#define RXTX_REG26 0x034
> +#define RXTX_REG26_PERIOD_ERROR_LATCH_SET(dst, src) \
> + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
> +#define RXTX_REG26_BLWC_ENA_SET(dst, src) \
> + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
> +#define RXTX_REG21 0x02a
> +#define RXTX_REG21_DO_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
> +#define RXTX_REG21_XO_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
> +#define RXTX_REG21_LATCH_CAL_FAIL_ODD_RD(src) ((0x0000000f & (u32)(src)))
> +#define RXTX_REG22 0x02c
> +#define RXTX_REG22_SO_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
> +#define RXTX_REG22_EO_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
> +#define RXTX_REG22_LATCH_CAL_FAIL_EVEN_RD(src) ((0x0000000f & (u32)(src)))
> +#define RXTX_REG23 0x02e
> +#define RXTX_REG23_DE_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
> +#define RXTX_REG23_XE_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
> +#define RXTX_REG24 0x030
> +#define RXTX_REG24_EE_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
> +#define RXTX_REG24_SE_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
> +#define RXTX_REG27 0x036
> +#define RXTX_REG28 0x038
> +#define RXTX_REG31 0x03e
> +#define RXTX_REG38 0x04c
> +#define RXTX_REG38_CUSTOMER_PINMODE_INV_SET(dst, src) \
> + (((dst) & 0x0000fffe) | (((u32) (src) << 1) & 0x0000fffe))
> +#define RXTX_REG39 0x04e
> +#define RXTX_REG40 0x050
> +#define RXTX_REG41 0x052
> +#define RXTX_REG42 0x054
> +#define RXTX_REG43 0x056
> +#define RXTX_REG44 0x058
> +#define RXTX_REG45 0x05a
> +#define RXTX_REG46 0x05c
> +#define RXTX_REG47 0x05e
> +#define RXTX_REG48 0x060
> +#define RXTX_REG49 0x062
> +#define RXTX_REG50 0x064
> +#define RXTX_REG51 0x066
> +#define RXTX_REG52 0x068
> +#define RXTX_REG53 0x06a
> +#define RXTX_REG54 0x06c
> +#define RXTX_REG55 0x06e
> +#define RXTX_REG61 0x07a
> +#define RXTX_REG61_ISCAN_INBERT_SET(dst, src) \
> + (((dst) & ~0x00000010) | (((u32) (src) << 4) & 0x00000010))
> +#define RXTX_REG61_LOADFREQ_SHIFT_SET(dst, src) \
> + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
> +#define RXTX_REG61_EYE_COUNT_WIDTH_SEL_SET(dst, src) \
> + (((dst) & ~0x000000c0) | (((u32) (src) << 6) & 0x000000c0))
> +#define RXTX_REG61_SPD_SEL_CDR_SET(dst, src) \
> + (((dst) & ~0x00003c00) | (((u32) (src) << 10) & 0x00003c00))
> +#define RXTX_REG62 0x07c
> +#define RXTX_REG62_PERIOD_H1_QLATCH_SET(dst, src) \
> + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
> +#define RXTX_REG81 0x0a2
> +#define RXTX_REG89_MU_TH7_SET(dst, src) \
> + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
> +#define RXTX_REG89_MU_TH8_SET(dst, src) \
> + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
> +#define RXTX_REG89_MU_TH9_SET(dst, src) \
> + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
> +#define RXTX_REG96 0x0c0
> +#define RXTX_REG96_MU_FREQ1_SET(dst, src) \
> + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
> +#define RXTX_REG96_MU_FREQ2_SET(dst, src) \
> + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
> +#define RXTX_REG96_MU_FREQ3_SET(dst, src) \
> + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
> +#define RXTX_REG99 0x0c6
> +#define RXTX_REG99_MU_PHASE1_SET(dst, src) \
> + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
> +#define RXTX_REG99_MU_PHASE2_SET(dst, src) \
> + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
> +#define RXTX_REG99_MU_PHASE3_SET(dst, src) \
> + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
> +#define RXTX_REG102 0x0cc
> +#define RXTX_REG102_FREQLOOP_LIMIT_SET(dst, src) \
> + (((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060))
> +#define RXTX_REG114 0x0e4
> +#define RXTX_REG121 0x0f2
> +#define RXTX_REG121_SUMOS_CAL_CODE_RD(src) ((0x0000003e & (u32)(src)) >> 0x1)
> +#define RXTX_REG125 0x0fa
> +#define RXTX_REG125_PQ_REG_SET(dst, src) \
> + (((dst) & ~0x0000fe00) | (((u32) (src) << 9) & 0x0000fe00))
> +#define RXTX_REG125_SIGN_PQ_SET(dst, src) \
> + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
> +#define RXTX_REG125_SIGN_PQ_2C_SET(dst, src) \
> + (((dst) & ~0x00000080) | (((u32) (src) << 7) & 0x00000080))
> +#define RXTX_REG125_PHZ_MANUALCODE_SET(dst, src) \
> + (((dst) & ~0x0000007c) | (((u32) (src) << 2) & 0x0000007c))
> +#define RXTX_REG125_PHZ_MANUAL_SET(dst, src) \
> + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
> +#define RXTX_REG127 0x0fe
> +#define RXTX_REG127_FORCE_SUM_CAL_START_MASK 0x00000002
> +#define RXTX_REG127_FORCE_LAT_CAL_START_MASK 0x00000004
> +#define RXTX_REG127_FORCE_SUM_CAL_START_SET(dst, src) \
> + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
> +#define RXTX_REG127_FORCE_LAT_CAL_START_SET(dst, src) \
> + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
> +#define RXTX_REG127_LATCH_MAN_CAL_ENA_SET(dst, src) \
> + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
> +#define RXTX_REG127_DO_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
> +#define RXTX_REG127_XO_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
> +#define RXTX_REG128 0x100
> +#define RXTX_REG128_LATCH_CAL_WAIT_SEL_SET(dst, src) \
> + (((dst) & ~0x0000000c) | (((u32) (src) << 2) & 0x0000000c))
> +#define RXTX_REG128_EO_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
> +#define RXTX_REG128_SO_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
> +#define RXTX_REG129 0x102
> +#define RXTX_REG129_DE_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
> +#define RXTX_REG129_XE_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
> +#define RXTX_REG130 0x104
> +#define RXTX_REG130_EE_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
> +#define RXTX_REG130_SE_LATCH_MANCAL_SET(dst, src) \
> + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
> +#define RXTX_REG145 0x122
> +#define RXTX_REG145_TX_IDLE_SATA_SET(dst, src) \
> + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
> +#define RXTX_REG145_RXES_ENA_SET(dst, src) \
> + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
> +#define RXTX_REG145_RXDFE_CONFIG_SET(dst, src) \
> + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
> +#define RXTX_REG145_RXVWES_LATENA_SET(dst, src) \
> + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
> +#define RXTX_REG147 0x126
> +#define RXTX_REG148 0x128
> +
> +/* Clock macro type */
> +enum cmu_type_t {
> + REF_CMU = 0, /* Clock macro is the internal reference clock */
> + PHY_CMU = 1, /* Clock macro is the PLL for the Serdes */
> +};
> +
> +enum mux_type_t {
> + MUX_SELECT_ATA = 0, /* Switch the MUX to ATA */
> + MUX_SELECT_SGMMII = 0, /* Switch the MUX to SGMII */
> +};
> +
> +enum clk_type_t {
> + CLK_EXT_DIFF = 0, /* External differential */
> + CLK_INT_DIFF = 1, /* Internal differential */
> + CLK_INT_SING = 2, /* Internal single ended */
> +};
> +
> +enum phy_mode {
> + MODE_SATA = 0, /* List them for simple reference */
> + MODE_SGMII = 1,
> + MODE_PCIE = 2,
> + MODE_USB = 3,
> + MODE_XFI = 4,
> + MODE_MAX
> +};
> +
> +struct xgene_sata_override_param {
> + u32 speed[MAX_LANE]; /* Index for override parameter per lane */
> + u32 txspeed[3]; /* Tx speed */
> + u32 txboostgain[MAX_LANE*3]; /* Tx freq boost and gain control */
> + u32 txeyetuning[MAX_LANE*3]; /* Tx eye tuning */
> + u32 txeyedirection[MAX_LANE*3]; /* Tx eye tuning direction */
> + u32 txamplitude[MAX_LANE*3]; /* Tx amplitude control */
> + u32 txprecursor_cn1[MAX_LANE*3]; /* Tx emphasis taps 1st pre-cursor */
> + u32 txprecursor_cn2[MAX_LANE*3]; /* Tx emphasis taps 2nd pre-cursor */
> + u32 txpostcursor_cp1[MAX_LANE*3]; /* Tx emphasis taps post-cursor */
> +};
> +
> +struct xgene_phy_ctx {
> + struct device *dev;
> + struct phy *phy;
> + enum phy_mode mode; /* Mode of operation */
> + enum clk_type_t clk_type; /* Input clock selection */
> + void __iomem *sds_base; /* PHY CSR base addr */
> + struct clk *clk; /* Optional clock */
> +
> + /* Override Serdes parameters */
> + struct xgene_sata_override_param sata_param;
> +};
> +
> +/*
> + * For chip earlier than A3 version, enable this flag.
> + * To enable, pass boot argument phy_xgene.preA3Chip=1
> + */
> +static int preA3Chip;
> +MODULE_PARM_DESC(preA3Chip, "Enable pre-A3 chip support (1=enable 0=disable)");
> +module_param_named(preA3Chip, preA3Chip, int, 0444);
> +
> +static void sds_wr(void __iomem *csr_base, u32 indirect_cmd_reg,
> + u32 indirect_data_reg, u32 addr, u32 data)
> +{
> + unsigned long deadline = jiffies + HZ;
> + u32 val;
> + u32 cmd;
> +
> + cmd = CFG_IND_WR_CMD_MASK | CFG_IND_CMD_DONE_MASK;
> + cmd = CFG_IND_ADDR_SET(cmd, addr);
> + writel(data, csr_base + indirect_data_reg);
> + readl(csr_base + indirect_data_reg); /* Force a barrier */
> + writel(cmd, csr_base + indirect_cmd_reg);
> + readl(csr_base + indirect_cmd_reg); /* Force a barrier */
> + do {
> + val = readl(csr_base + indirect_cmd_reg);
> + } while (!(val & CFG_IND_CMD_DONE_MASK) &&
> + time_before(jiffies, deadline));
> + if (!(val & CFG_IND_CMD_DONE_MASK))
> + pr_err("SDS WR timeout at 0x%p offset 0x%08X value 0x%08X\n",
> + csr_base + indirect_cmd_reg, addr, data);
> +}
> +
> +static void sds_rd(void __iomem *csr_base, u32 indirect_cmd_reg,
> + u32 indirect_data_reg, u32 addr, u32 *data)
> +{
> + unsigned long deadline = jiffies + HZ;
> + u32 val;
> + u32 cmd;
> +
> + cmd = CFG_IND_RD_CMD_MASK | CFG_IND_CMD_DONE_MASK;
> + cmd = CFG_IND_ADDR_SET(cmd, addr);
> + writel(cmd, csr_base + indirect_cmd_reg);
> + readl(csr_base + indirect_cmd_reg); /* Force a barrier */
> + do {
> + val = readl(csr_base + indirect_cmd_reg);
> + } while (!(val & CFG_IND_CMD_DONE_MASK) &&
> + time_before(jiffies, deadline));
> + *data = readl(csr_base + indirect_data_reg);
> + if (!(val & CFG_IND_CMD_DONE_MASK))
> + pr_err("SDS WR timeout at 0x%p offset 0x%08X value 0x%08X\n",
> + csr_base + indirect_cmd_reg, addr, *data);
> +}
> +
> +static void cmu_wr(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
> + u32 reg, u32 data)
> +{
> + void __iomem *sds_base = ctx->sds_base;
> + u32 val;
> +
> + if (cmu_type == REF_CMU)
> + reg += SERDES_PLL_REF_INDIRECT_OFFSET;
> + else
> + reg += SERDES_PLL_INDIRECT_OFFSET;
> + sds_wr(sds_base, SATA_ENET_SDS_IND_CMD_REG,
> + SATA_ENET_SDS_IND_WDATA_REG, reg, data);
> + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
> + SATA_ENET_SDS_IND_RDATA_REG, reg, &val);
> + pr_debug("CMU WR addr 0x%X value 0x%08X <-> 0x%08X\n", reg, data, val);
> +}
> +
> +static void cmu_rd(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
> + u32 reg, u32 *data)
> +{
> + void __iomem *sds_base = ctx->sds_base;
> +
> + if (cmu_type == REF_CMU)
> + reg += SERDES_PLL_REF_INDIRECT_OFFSET;
> + else
> + reg += SERDES_PLL_INDIRECT_OFFSET;
> + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
> + SATA_ENET_SDS_IND_RDATA_REG, reg, data);
> + pr_debug("CMU RD addr 0x%X value 0x%08X\n", reg, *data);
> +}
> +
> +static void cmu_toggle1to0(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
> + u32 reg, u32 bits)
> +{
> + u32 val;
> +
> + cmu_rd(ctx, cmu_type, reg, &val);
> + val |= bits;
> + cmu_wr(ctx, cmu_type, reg, val);
> + cmu_rd(ctx, cmu_type, reg, &val);
> + val &= ~bits;
> + cmu_wr(ctx, cmu_type, reg, val);
> +}
> +
> +static void cmu_clrbits(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
> + u32 reg, u32 bits)
> +{
> + u32 val;
> +
> + cmu_rd(ctx, cmu_type, reg, &val);
> + val &= ~bits;
> + cmu_wr(ctx, cmu_type, reg, val);
> +}
> +
> +static void cmu_setbits(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
> + u32 reg, u32 bits)
> +{
> + u32 val;
> +
> + cmu_rd(ctx, cmu_type, reg, &val);
> + val |= bits;
> + cmu_wr(ctx, cmu_type, reg, val);
> +}
> +
> +static void serdes_wr(struct xgene_phy_ctx *ctx, int lane, u32 reg, u32 data)
> +{
> + void __iomem *sds_base = ctx->sds_base;
> + u32 val;
> +
> + reg += SERDES_INDIRECT_OFFSET;
> + reg += lane * SERDES_LANE_STRIDE;
> + sds_wr(sds_base, SATA_ENET_SDS_IND_CMD_REG,
> + SATA_ENET_SDS_IND_WDATA_REG, reg, data);
> + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
> + SATA_ENET_SDS_IND_RDATA_REG, reg, &val);
> + pr_debug("SERDES WR addr 0x%X value 0x%08X <-> 0x%08X\n", reg, data,
> + val);
> +}
> +
> +static void serdes_rd(struct xgene_phy_ctx *ctx, int lane, u32 reg, u32 *data)
> +{
> + void __iomem *sds_base = ctx->sds_base;
> +
> + reg += SERDES_INDIRECT_OFFSET;
> + reg += lane * SERDES_LANE_STRIDE;
> + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
> + SATA_ENET_SDS_IND_RDATA_REG, reg, data);
> + pr_debug("SERDES RD addr 0x%X value 0x%08X\n", reg, *data);
> +}
> +
> +static void serdes_clrbits(struct xgene_phy_ctx *ctx, int lane, u32 reg,
> + u32 bits)
> +{
> + u32 val;
> +
> + serdes_rd(ctx, lane, reg, &val);
> + val &= ~bits;
> + serdes_wr(ctx, lane, reg, val);
> +}
> +
> +static void serdes_setbits(struct xgene_phy_ctx *ctx, int lane, u32 reg,
> + u32 bits)
> +{
> + u32 val;
> +
> + serdes_rd(ctx, lane, reg, &val);
> + val |= bits;
> + serdes_wr(ctx, lane, reg, val);
> +}
> +
> +static void xgene_phy_cfg_cmu_clk_type(struct xgene_phy_ctx *ctx,
> + enum cmu_type_t cmu_type,
> + enum clk_type_t clk_type)
> +{
> + u32 val;
> +
> + /* Set the reset sequence delay for TX ready assertion */
> + cmu_rd(ctx, cmu_type, CMU_REG12, &val);
> + val = CMU_REG12_STATE_DELAY9_SET(val, 0x1);
> + cmu_wr(ctx, cmu_type, CMU_REG12, val);
> + /* Set the programmable stage delays between various enable stages */
> + cmu_wr(ctx, cmu_type, CMU_REG13, 0x0222);
> + cmu_wr(ctx, cmu_type, CMU_REG14, 0x2225);
> +
> + /* Configure clock type */
> + if (clk_type == CLK_EXT_DIFF) {
> + /* Select external clock mux */
> + cmu_rd(ctx, cmu_type, CMU_REG0, &val);
> + val = CMU_REG0_PLL_REF_SEL_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG0, val);
> + /* Select CMOS as reference clock */
> + cmu_rd(ctx, cmu_type, CMU_REG1, &val);
> + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG1, val);
> + dev_dbg(ctx->dev, "Set external reference clock\n");
> + } else if (clk_type == CLK_INT_DIFF) {
> + /* Select internal clock mux */
> + cmu_rd(ctx, cmu_type, CMU_REG0, &val);
> + val = CMU_REG0_PLL_REF_SEL_SET(val, 0x1);
> + cmu_wr(ctx, cmu_type, CMU_REG0, val);
> + /* Select CMOS as reference clock */
> + cmu_rd(ctx, cmu_type, CMU_REG1, &val);
> + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x1);
> + cmu_wr(ctx, cmu_type, CMU_REG1, val);
> + dev_dbg(ctx->dev, "Set internal reference clock\n");
> + } else if (clk_type == CLK_INT_SING) {
> + /*
> + * NOTE: This clock type is NOT support for controller
> + * whose internal clock shared in the PCIe controller
> + *
> + * Select internal clock mux
> + */
> + cmu_rd(ctx, cmu_type, CMU_REG1, &val);
> + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x1);
> + cmu_wr(ctx, cmu_type, CMU_REG1, val);
> + /* Select CML as reference clock */
> + cmu_rd(ctx, cmu_type, CMU_REG1, &val);
> + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG1, val);
> + dev_dbg(ctx->dev,
> + "Set internal single ended reference clock\n");
> + }
> +}
> +
> +static void xgene_phy_sata_cfg_cmu_core(struct xgene_phy_ctx *ctx,
> + enum cmu_type_t cmu_type,
> + enum clk_type_t clk_type)
> +{
> + u32 val;
> + int ref_100MHz;
> +
> + if (cmu_type == REF_CMU) {
> + /* Set VCO calibration voltage threshold */
> + cmu_rd(ctx, cmu_type, CMU_REG34, &val);
> + val = CMU_REG34_VCO_CAL_VTH_LO_MAX_SET(val, 0x7);
> + val = CMU_REG34_VCO_CAL_VTH_HI_MAX_SET(val, 0xc);
> + val = CMU_REG34_VCO_CAL_VTH_LO_MIN_SET(val, 0x3);
> + val = CMU_REG34_VCO_CAL_VTH_HI_MIN_SET(val, 0x8);
> + cmu_wr(ctx, cmu_type, CMU_REG34, val);
> + }
> +
> + /* Set the VCO calibration counter */
> + cmu_rd(ctx, cmu_type, CMU_REG0, &val);
> + if (cmu_type == REF_CMU || preA3Chip)
> + val = CMU_REG0_CAL_COUNT_RESOL_SET(val, 0x4);
> + else
> + val = CMU_REG0_CAL_COUNT_RESOL_SET(val, 0x7);
> + cmu_wr(ctx, cmu_type, CMU_REG0, val);
> +
> + /* Configure PLL for calibration */
> + cmu_rd(ctx, cmu_type, CMU_REG1, &val);
> + val = CMU_REG1_PLL_CP_SET(val, 0x1);
> + if (cmu_type == REF_CMU || preA3Chip)
> + val = CMU_REG1_PLL_CP_SEL_SET(val, 0x5);
> + else
> + val = CMU_REG1_PLL_CP_SEL_SET(val, 0x3);
> + if (cmu_type == REF_CMU)
> + val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x0);
> + else
> + val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x1);
> + cmu_wr(ctx, cmu_type, CMU_REG1, val);
> +
> + if (cmu_type != REF_CMU)
> + cmu_clrbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
> +
> + /* Configure the PLL for either 100MHz or 50MHz */
> + cmu_rd(ctx, cmu_type, CMU_REG2, &val);
> + if (cmu_type == REF_CMU) {
> + val = CMU_REG2_PLL_LFRES_SET(val, 0xa);
> + ref_100MHz = 1;
> + } else {
> + val = CMU_REG2_PLL_LFRES_SET(val, 0x3);
> + if (clk_type == CLK_EXT_DIFF)
> + ref_100MHz = 0;
> + else
> + ref_100MHz = 1;
> + }
> + if (ref_100MHz) {
> + val = CMU_REG2_PLL_FBDIV_SET(val, FBDIV_VAL_100M);
> + val = CMU_REG2_PLL_REFDIV_SET(val, REFDIV_VAL_100M);
> + } else {
> + val = CMU_REG2_PLL_FBDIV_SET(val, FBDIV_VAL_50M);
> + val = CMU_REG2_PLL_REFDIV_SET(val, REFDIV_VAL_50M);
> + }
> + cmu_wr(ctx, cmu_type, CMU_REG2, val);
> +
> + /* Configure the VCO */
> + cmu_rd(ctx, cmu_type, CMU_REG3, &val);
> + if (cmu_type == REF_CMU) {
> + val = CMU_REG3_VCOVARSEL_SET(val, 0x3);
> + val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x10);
> + } else {
> + val = CMU_REG3_VCOVARSEL_SET(val, 0xF);
> + if (preA3Chip)
> + val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x15);
> + else
> + val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x1a);
> + val = CMU_REG3_VCO_MANMOMSEL_SET(val, 0x15);
> + }
> + cmu_wr(ctx, cmu_type, CMU_REG3, val);
> +
> + /* Disable force PLL lock */
> + cmu_rd(ctx, cmu_type, CMU_REG26, &val);
> + val = CMU_REG26_FORCE_PLL_LOCK_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG26, val);
> +
> + /* Setup PLL loop filter */
> + cmu_rd(ctx, cmu_type, CMU_REG5, &val);
> + val = CMU_REG5_PLL_LFSMCAP_SET(val, 0x3);
> + val = CMU_REG5_PLL_LFCAP_SET(val, 0x3);
> + if (cmu_type == REF_CMU || !preA3Chip)
> + val = CMU_REG5_PLL_LOCK_RESOLUTION_SET(val, 0x7);
> + else
> + val = CMU_REG5_PLL_LOCK_RESOLUTION_SET(val, 0x4);
> + cmu_wr(ctx, cmu_type, CMU_REG5, val);
> +
> + /* Enable or disable manual calibration */
> + cmu_rd(ctx, cmu_type, CMU_REG6, &val);
> + val = CMU_REG6_PLL_VREGTRIM_SET(val, preA3Chip ? 0x0 : 0x2);
> + val = CMU_REG6_MAN_PVT_CAL_SET(val, preA3Chip ? 0x1 : 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG6, val);
> +
> + /* Configure lane for 20-bits */
> + if (cmu_type == PHY_CMU) {
> + cmu_rd(ctx, cmu_type, CMU_REG9, &val);
> + val = CMU_REG9_TX_WORD_MODE_CH1_SET(val,
> + CMU_REG9_WORD_LEN_20BIT);
> + val = CMU_REG9_TX_WORD_MODE_CH0_SET(val,
> + CMU_REG9_WORD_LEN_20BIT);
> + val = CMU_REG9_PLL_POST_DIVBY2_SET(val, 0x1);
> + if (!preA3Chip) {
> + val = CMU_REG9_VBG_BYPASSB_SET(val, 0x0);
> + val = CMU_REG9_IGEN_BYPASS_SET(val , 0x0);
> + }
> + cmu_wr(ctx, cmu_type, CMU_REG9, val);
> +
> + if (!preA3Chip) {
> + cmu_rd(ctx, cmu_type, CMU_REG10, &val);
> + val = CMU_REG10_VREG_REFSEL_SET(val, 0x1);
> + cmu_wr(ctx, cmu_type, CMU_REG10, val);
> + }
> + }
> +
> + cmu_rd(ctx, cmu_type, CMU_REG16, &val);
> + val = CMU_REG16_CALIBRATION_DONE_OVERRIDE_SET(val, 0x1);
> + val = CMU_REG16_BYPASS_PLL_LOCK_SET(val, 0x1);
> + if (cmu_type == REF_CMU || preA3Chip)
> + val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x4);
> + else
> + val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x7);
> + cmu_wr(ctx, cmu_type, CMU_REG16, val);
> +
> + /* Configure for SATA */
> + cmu_rd(ctx, cmu_type, CMU_REG30, &val);
> + val = CMU_REG30_PCIE_MODE_SET(val, 0x0);
> + val = CMU_REG30_LOCK_COUNT_SET(val, 0x3);
> + cmu_wr(ctx, cmu_type, CMU_REG30, val);
> +
> + /* Disable state machine bypass */
> + cmu_wr(ctx, cmu_type, CMU_REG31, 0xF);
> +
> + cmu_rd(ctx, cmu_type, CMU_REG32, &val);
> + val = CMU_REG32_PVT_CAL_WAIT_SEL_SET(val, 0x3);
> + if (cmu_type == REF_CMU || preA3Chip)
> + val = CMU_REG32_IREF_ADJ_SET(val, 0x3);
> + else
> + val = CMU_REG32_IREF_ADJ_SET(val, 0x1);
> + cmu_wr(ctx, cmu_type, CMU_REG32, val);
> +
> + /* Set VCO calibration threshold */
> + if (cmu_type != REF_CMU && preA3Chip)
> + cmu_wr(ctx, cmu_type, CMU_REG34, 0x8d27);
> + else
> + cmu_wr(ctx, cmu_type, CMU_REG34, 0x873c);
> +
> + /* Set CTLE Override and override waiting from state machine */
> + cmu_wr(ctx, cmu_type, CMU_REG37, 0xF00F);
> +}
> +
> +static void xgene_phy_ssc_enable(struct xgene_phy_ctx *ctx,
> + enum cmu_type_t cmu_type)
> +{
> + u32 val;
> +
> + /* Set SSC modulation value */
> + cmu_rd(ctx, cmu_type, CMU_REG35, &val);
> + val = CMU_REG35_PLL_SSC_MOD_SET(val, 98);
> + cmu_wr(ctx, cmu_type, CMU_REG35, val);
> +
> + /* Enable SSC, set vertical step and DSM value */
> + cmu_rd(ctx, cmu_type, CMU_REG36, &val);
> + val = CMU_REG36_PLL_SSC_VSTEP_SET(val, 30);
> + val = CMU_REG36_PLL_SSC_EN_SET(val, 1);
> + val = CMU_REG36_PLL_SSC_DSMSEL_SET(val, 1);
> + cmu_wr(ctx, cmu_type, CMU_REG36, val);
> +
> + /* Reset the PLL */
> + cmu_clrbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
> + cmu_setbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
> +
> + /* Force VCO calibration to restart */
> + cmu_toggle1to0(ctx, cmu_type, CMU_REG32,
> + CMU_REG32_FORCE_VCOCAL_START_MASK);
> +}
> +
> +static void xgene_phy_sata_cfg_lanes(struct xgene_phy_ctx *ctx)
> +{
> + u32 val;
> + u32 reg;
> + int i;
> + int lane;
> +
> + for (lane = 0; lane < MAX_LANE; lane++) {
> + serdes_wr(ctx, lane, RXTX_REG147, 0x6);
> +
> + /* Set boost control for quarter, half, and full rate */
> + serdes_rd(ctx, lane, RXTX_REG0, &val);
> + val = RXTX_REG0_CTLE_EQ_HR_SET(val, 0x10);
> + val = RXTX_REG0_CTLE_EQ_QR_SET(val, 0x10);
> + val = RXTX_REG0_CTLE_EQ_FR_SET(val, 0x10);
> + serdes_wr(ctx, lane, RXTX_REG0, val);
> +
> + /* Set boost control value */
> + serdes_rd(ctx, lane, RXTX_REG1, &val);
> + val = RXTX_REG1_RXACVCM_SET(val, 0x7);
> + val = RXTX_REG1_CTLE_EQ_SET(val,
> + ctx->sata_param.txboostgain[lane * 3 +
> + ctx->sata_param.speed[lane]]);
> + serdes_wr(ctx, lane, RXTX_REG1, val);
> +
> + /* Latch VTT value based on the termination to ground and
> + enable TX FIFO */
> + serdes_rd(ctx, lane, RXTX_REG2, &val);
> + val = RXTX_REG2_VTT_ENA_SET(val, 0x1);
> + val = RXTX_REG2_VTT_SEL_SET(val, 0x1);
> + val = RXTX_REG2_TX_FIFO_ENA_SET(val, 0x1);
> + serdes_wr(ctx, lane, RXTX_REG2, val);
> +
> + /* Configure Tx for 20-bits */
> + serdes_rd(ctx, lane, RXTX_REG4, &val);
> + val = RXTX_REG4_TX_WORD_MODE_SET(val, CMU_REG9_WORD_LEN_20BIT);
> + serdes_wr(ctx, lane, RXTX_REG4, val);
> +
> + if (!preA3Chip) {
> + serdes_rd(ctx, lane, RXTX_REG1, &val);
> + val = RXTX_REG1_RXVREG1_SET(val, 0x2);
> + val = RXTX_REG1_RXIREF_ADJ_SET(val, 0x2);
> + serdes_wr(ctx, lane, RXTX_REG1, val);
> + }
> +
> + /* Set pre-emphasis first 1 and 2, and post-emphasis values */
> + serdes_rd(ctx, lane, RXTX_REG5, &val);
> + val = RXTX_REG5_TX_CN1_SET(val,
> + ctx->sata_param.txprecursor_cn1[lane * 3 +
> + ctx->sata_param.speed[lane]]);
> + val = RXTX_REG5_TX_CP1_SET(val,
> + ctx->sata_param.txpostcursor_cp1[lane * 3 +
> + ctx->sata_param.speed[lane]]);
> + val = RXTX_REG5_TX_CN2_SET(val,
> + ctx->sata_param.txprecursor_cn2[lane * 3 +
> + ctx->sata_param.speed[lane]]);
> + serdes_wr(ctx, lane, RXTX_REG5, val);
> +
> + /* Set TX amplitude value */
> + serdes_rd(ctx, lane, RXTX_REG6, &val);
> + val = RXTX_REG6_TXAMP_CNTL_SET(val,
> + ctx->sata_param.txamplitude[lane * 3 +
> + ctx->sata_param.speed[lane]]);
> + val = RXTX_REG6_TXAMP_ENA_SET(val, 0x1);
> + val = RXTX_REG6_TX_IDLE_SET(val, 0x0);
> + val = RXTX_REG6_RX_BIST_RESYNC_SET(val, 0x0);
> + val = RXTX_REG6_RX_BIST_ERRCNT_RD_SET(val, 0x0);
> + serdes_wr(ctx, lane, RXTX_REG6, val);
> +
> + /* Configure Rx for 20-bits */
> + serdes_rd(ctx, lane, RXTX_REG7, &val);
> + val = RXTX_REG7_BIST_ENA_RX_SET(val, 0x0);
> + val = RXTX_REG7_RX_WORD_MODE_SET(val, CMU_REG9_WORD_LEN_20BIT);
> + serdes_wr(ctx, lane, RXTX_REG7, val);
> +
> + /* Set CDR and LOS values and enable Rx SSC */
> + serdes_rd(ctx, lane, RXTX_REG8, &val);
> + val = RXTX_REG8_CDR_LOOP_ENA_SET(val, 0x1);
> + val = RXTX_REG8_CDR_BYPASS_RXLOS_SET(val, 0x0);
> + val = RXTX_REG8_SSC_ENABLE_SET(val, 0x1);
> + val = RXTX_REG8_SD_DISABLE_SET(val, 0x0);
> + val = RXTX_REG8_SD_VREF_SET(val, 0x4);
> + serdes_wr(ctx, lane, RXTX_REG8, val);
> +
> + /* Set phase adjust upper/lower limits */
> + serdes_rd(ctx, lane, RXTX_REG11, &val);
> + val = RXTX_REG11_PHASE_ADJUST_LIMIT_SET(val, 0x0);
> + serdes_wr(ctx, lane, RXTX_REG11, val);
> +
> + /* Enable Latch Off; disable SUMOS and Tx termination */
> + serdes_rd(ctx, lane, RXTX_REG12, &val);
> + val = RXTX_REG12_LATCH_OFF_ENA_SET(val, 0x1);
> + val = RXTX_REG12_SUMOS_ENABLE_SET(val, 0x0);
> + val = RXTX_REG12_RX_DET_TERM_ENABLE_SET(val, 0x0);
> + serdes_wr(ctx, lane, RXTX_REG12, val);
> +
> + /* Set period error latch to 512T and enable BWL */
> + serdes_rd(ctx, lane, RXTX_REG26, &val);
> + val = RXTX_REG26_PERIOD_ERROR_LATCH_SET(val, 0x0);
> + val = RXTX_REG26_BLWC_ENA_SET(val, 0x1);
> + serdes_wr(ctx, lane, RXTX_REG26, val);
> +
> + serdes_wr(ctx, lane, RXTX_REG28, 0x0);
> +
> + /* Set DFE loop preset value */
> + serdes_wr(ctx, lane, RXTX_REG31, 0x0);
> +
> + /* Set Eye Monitor counter width to 12-bit */
> + serdes_rd(ctx, lane, RXTX_REG61, &val);
> + val = RXTX_REG61_ISCAN_INBERT_SET(val, 0x1);
> + val = RXTX_REG61_LOADFREQ_SHIFT_SET(val, 0x0);
> + val = RXTX_REG61_EYE_COUNT_WIDTH_SEL_SET(val, 0x0);
> + serdes_wr(ctx, lane, RXTX_REG61, val);
> +
> + serdes_rd(ctx, lane, RXTX_REG62, &val);
> + val = RXTX_REG62_PERIOD_H1_QLATCH_SET(val, 0x0);
> + serdes_wr(ctx, lane, RXTX_REG62, val);
> +
> + /* Set BW select tap X for DFE loop */
> + for (i = 0; i < 9; i++) {
> + reg = RXTX_REG81 + i * 2;
> + serdes_rd(ctx, lane, reg, &val);
> + val = RXTX_REG89_MU_TH7_SET(val, 0xe);
> + val = RXTX_REG89_MU_TH8_SET(val, 0xe);
> + val = RXTX_REG89_MU_TH9_SET(val, 0xe);
> + serdes_wr(ctx, lane, reg, val);
> + }
> +
> + /* Set BW select tap X for frequency adjust loop */
> + for (i = 0; i < 3; i++) {
> + reg = RXTX_REG96 + i * 2;
> + serdes_rd(ctx, lane, reg, &val);
> + val = RXTX_REG96_MU_FREQ1_SET(val, 0x10);
> + val = RXTX_REG96_MU_FREQ2_SET(val, 0x10);
> + val = RXTX_REG96_MU_FREQ3_SET(val, 0x10);
> + serdes_wr(ctx, lane, reg, val);
> + }
> +
> + /* Set BW select tap X for phase adjust loop */
> + for (i = 0; i < 3; i++) {
> + reg = RXTX_REG99 + i * 2;
> + serdes_rd(ctx, lane, reg, &val);
> + val = RXTX_REG99_MU_PHASE1_SET(val, 0x7);
> + val = RXTX_REG99_MU_PHASE2_SET(val, 0x7);
> + val = RXTX_REG99_MU_PHASE3_SET(val, 0x7);
> + serdes_wr(ctx, lane, reg, val);
> + }
> +
> + serdes_rd(ctx, lane, RXTX_REG102, &val);
> + val = RXTX_REG102_FREQLOOP_LIMIT_SET(val, 0x0);
> + serdes_wr(ctx, lane, RXTX_REG102, val);
> +
> + serdes_wr(ctx, lane, RXTX_REG114, 0xffe0);
> +
> + serdes_rd(ctx, lane, RXTX_REG125, &val);
> + val = RXTX_REG125_SIGN_PQ_SET(val,
> + ctx->sata_param.txeyedirection[lane * 3 +
> + ctx->sata_param.speed[lane]]);
> + val = RXTX_REG125_PQ_REG_SET(val,
> + ctx->sata_param.txeyetuning[lane * 3 +
> + ctx->sata_param.speed[lane]]);
> + val = RXTX_REG125_PHZ_MANUAL_SET(val, 0x1);
> + serdes_wr(ctx, lane, RXTX_REG125, val);
> +
> + serdes_rd(ctx, lane, RXTX_REG127, &val);
> + val = RXTX_REG127_LATCH_MAN_CAL_ENA_SET(val, 0x0);
> + serdes_wr(ctx, lane, RXTX_REG127, val);
> +
> + serdes_rd(ctx, lane, RXTX_REG128, &val);
> + val = RXTX_REG128_LATCH_CAL_WAIT_SEL_SET(val, 0x3);
> + serdes_wr(ctx, lane, RXTX_REG128, val);
> +
> + serdes_rd(ctx, lane, RXTX_REG145, &val);
> + val = RXTX_REG145_RXDFE_CONFIG_SET(val, 0x3);
> + val = RXTX_REG145_TX_IDLE_SATA_SET(val, 0x0);
> + if (preA3Chip) {
> + val = RXTX_REG145_RXES_ENA_SET(val, 0x1);
> + val = RXTX_REG145_RXVWES_LATENA_SET(val, 0x1);
> + } else {
> + val = RXTX_REG145_RXES_ENA_SET(val, 0x0);
> + val = RXTX_REG145_RXVWES_LATENA_SET(val, 0x0);
> + }
> + serdes_wr(ctx, lane, RXTX_REG145, val);
> +
> + /*
> + * Set Rx LOS filter clock rate, sample rate, and threshold
> + * windows
> + */
> + for (i = 0; i < 4; i++) {
> + reg = RXTX_REG148 + i * 2;
> + serdes_wr(ctx, lane, reg, 0xFFFF);
> + }
> + }
> +}
> +
> +static int xgene_phy_cal_rdy_chk(struct xgene_phy_ctx *ctx,
> + enum cmu_type_t cmu_type,
> + enum clk_type_t clk_type)
> +{
> + void __iomem *csr_serdes = ctx->sds_base;
> + int loop;
> + u32 val;
> +
> + /* Release PHY main reset */
> + writel(0xdf, csr_serdes + SATA_ENET_SDS_RST_CTL);
> + readl(csr_serdes + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
> +
> + if (cmu_type != REF_CMU) {
> + cmu_setbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
> + /*
> + * As per PHY design spec, the PLL reset requires a minimum
> + * of 800us.
> + */
> + usleep_range(800, 1000);
> +
> + cmu_rd(ctx, cmu_type, CMU_REG1, &val);
> + val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG1, val);
> + /*
> + * As per PHY design spec, the PLL auto calibration requires
> + * a minimum of 800us.
> + */
> + usleep_range(800, 1000);
> +
> + cmu_toggle1to0(ctx, cmu_type, CMU_REG32,
> + CMU_REG32_FORCE_VCOCAL_START_MASK);
> + /*
> + * As per PHY design spec, the PLL requires a minimum of
> + * 800us to settle.
> + */
> + usleep_range(800, 1000);
> + }
> +
> + if (!preA3Chip)
> + goto skip_manual_cal;
> +
> + /*
> + * Configure the termination resister calibration
> + * The serial receive pins, RXP/RXN, have TERMination resistor
> + * that is required to be calibrated.
> + */
> + cmu_rd(ctx, cmu_type, CMU_REG17, &val);
> + val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x12);
> + val = CMU_REG17_RESERVED_7_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG17, val);
> + cmu_toggle1to0(ctx, cmu_type, CMU_REG17,
> + CMU_REG17_PVT_TERM_MAN_ENA_MASK);
> + /*
> + * The serial transmit pins, TXP/TXN, have Pull-UP and Pull-DOWN
> + * resistors that are required to the calibrated.
> + * Configure the pull DOWN calibration
> + */
> + cmu_rd(ctx, cmu_type, CMU_REG17, &val);
> + val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x29);
> + val = CMU_REG17_RESERVED_7_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG17, val);
> + cmu_toggle1to0(ctx, cmu_type, CMU_REG16,
> + CMU_REG16_PVT_DN_MAN_ENA_MASK);
> + /* Configure the pull UP calibration */
> + cmu_rd(ctx, cmu_type, CMU_REG17, &val);
> + val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x28);
> + val = CMU_REG17_RESERVED_7_SET(val, 0x0);
> + cmu_wr(ctx, cmu_type, CMU_REG17, val);
> + cmu_toggle1to0(ctx, cmu_type, CMU_REG16,
> + CMU_REG16_PVT_UP_MAN_ENA_MASK);
> +
> +skip_manual_cal:
> + /* Poll the PLL calibration completion status for at least 1 ms */
> + loop = 100;
> + do {
> + cmu_rd(ctx, cmu_type, CMU_REG7, &val);
> + if (CMU_REG7_PLL_CALIB_DONE_RD(val))
> + break;
> + /*
> + * As per PHY design spec, PLL calibration status requires
> + * a minimum of 10us to be updated.
> + */
> + usleep_range(10, 100);
> + } while (--loop > 0);
> +
> + cmu_rd(ctx, cmu_type, CMU_REG7, &val);
> + dev_dbg(ctx->dev, "PLL calibration %s\n",
> + CMU_REG7_PLL_CALIB_DONE_RD(val) ? "done" : "failed");
> + if (CMU_REG7_VCO_CAL_FAIL_RD(val)) {
> + dev_err(ctx->dev,
> + "PLL calibration failed due to VCO failure\n");
> + return -1;
> + }
> + dev_dbg(ctx->dev, "PLL calibration successful\n");
> +
> + cmu_rd(ctx, cmu_type, CMU_REG15, &val);
> + dev_dbg(ctx->dev, "PHY Tx is %sready\n", val & 0x300 ? "" : "not ");
> + return 0;
> +}
> +
> +static void xgene_phy_pdwn_force_vco(struct xgene_phy_ctx *ctx,
> + enum cmu_type_t cmu_type,
> + enum clk_type_t clk_type)
> +{
> + u32 val;
> +
> + dev_dbg(ctx->dev, "Reset VCO and re-start again\n");
> + if (cmu_type == PHY_CMU) {
> + cmu_rd(ctx, cmu_type, CMU_REG16, &val);
> + val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x7);
> + cmu_wr(ctx, cmu_type, CMU_REG16, val);
> + }
> +
> + cmu_toggle1to0(ctx, cmu_type, CMU_REG0, CMU_REG0_PDOWN_MASK);
> + cmu_toggle1to0(ctx, cmu_type, CMU_REG32,
> + CMU_REG32_FORCE_VCOCAL_START_MASK);
> +}
> +
> +static int xgene_phy_hw_init_sata(struct xgene_phy_ctx *ctx,
> + enum clk_type_t clk_type, int ssc_enable)
> +{
> + void __iomem *sds_base = ctx->sds_base;
> + u32 val;
> + int i;
> +
> + /* Configure the PHY for operation */
> + dev_dbg(ctx->dev, "Reset PHY\n");
> + /* Place PHY into reset */
> + writel(0x0, sds_base + SATA_ENET_SDS_RST_CTL);
> + val = readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
> + /* Release PHY lane from reset (active high) */
> + writel(0x20, sds_base + SATA_ENET_SDS_RST_CTL);
> + readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
> + /* Release all PHY module out of reset except PHY main reset */
> + writel(0xde, sds_base + SATA_ENET_SDS_RST_CTL);
> + readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
> +
> + /* Set the operation speed */
> + val = readl(sds_base + SATA_ENET_SDS_CTL1);
> + val = CFG_I_SPD_SEL_CDR_OVR1_SET(val,
> + ctx->sata_param.txspeed[ctx->sata_param.speed[0]]);
> + writel(val, sds_base + SATA_ENET_SDS_CTL1);
> +
> + dev_dbg(ctx->dev, "Set the customer pin mode to SATA\n");
> + val = readl(sds_base + SATA_ENET_SDS_CTL0);
> + val = REGSPEC_CFG_I_CUSTOMER_PIN_MODE0_SET(val, 0x4421);
> + writel(val, sds_base + SATA_ENET_SDS_CTL0);
> +
> + /* Configure the clock macro unit (CMU) clock type */
> + xgene_phy_cfg_cmu_clk_type(ctx, PHY_CMU, clk_type);
> +
> + /* Configure the clock macro */
> + xgene_phy_sata_cfg_cmu_core(ctx, PHY_CMU, clk_type);
> +
> + /* Enable SSC if enabled */
> + if (ssc_enable)
> + xgene_phy_ssc_enable(ctx, PHY_CMU);
> +
> + /* Configure PHY lanes */
> + xgene_phy_sata_cfg_lanes(ctx);
> +
> + /* Set Rx/Tx 20-bit */
> + val = readl(sds_base + SATA_ENET_SDS_PCS_CTL0);
> + val = REGSPEC_CFG_I_RX_WORDMODE0_SET(val, 0x3);
> + val = REGSPEC_CFG_I_TX_WORDMODE0_SET(val, 0x3);
> + writel(val, sds_base + SATA_ENET_SDS_PCS_CTL0);
> +
> + /* Start PLL calibration and try for three times */
> + i = 10;
> + do {
> + if (!xgene_phy_cal_rdy_chk(ctx, PHY_CMU, clk_type))
> + break;
> + /* If failed, toggle the VCO power signal and start again */
> + xgene_phy_pdwn_force_vco(ctx, PHY_CMU, clk_type);
> + } while (--i > 0);
> + /* Even on failure, allow to continue any way */
> + if (i <= 0)
> + dev_err(ctx->dev, "PLL calibration failed\n");
> +
> + return 0;
> +}
> +
> +static int xgene_phy_hw_initialize(struct xgene_phy_ctx *ctx,
> + enum clk_type_t clk_type,
> + int ssc_enable)
> +{
> + int rc;
> +
> + dev_dbg(ctx->dev, "PHY init clk type %d\n", clk_type);
> +
> + if (ctx->mode == MODE_SATA) {
> + rc = xgene_phy_hw_init_sata(ctx, clk_type, ssc_enable);
> + if (rc)
> + return rc;
> + } else {
> + dev_err(ctx->dev, "Un-supported customer pin mode %d\n",
> + ctx->mode);
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * Receiver Offset Calibration:
> + *
> + * Calibrate the receiver signal path offset in two steps - summar and
> + * latch calibrations
> + */
> +static void xgene_phy_force_lat_summer_cal(struct xgene_phy_ctx *ctx, int lane)
> +{
> + int i;
> + struct {
> + u32 reg;
> + u32 val;
> + } serdes_reg[] = {
> + {RXTX_REG38, 0x0},
> + {RXTX_REG39, 0xff00},
> + {RXTX_REG40, 0xffff},
> + {RXTX_REG41, 0xffff},
> + {RXTX_REG42, 0xffff},
> + {RXTX_REG43, 0xffff},
> + {RXTX_REG44, 0xffff},
> + {RXTX_REG45, 0xffff},
> + {RXTX_REG46, 0xffff},
> + {RXTX_REG47, 0xfffc},
> + {RXTX_REG48, 0x0},
> + {RXTX_REG49, 0x0},
> + {RXTX_REG50, 0x0},
> + {RXTX_REG51, 0x0},
> + {RXTX_REG52, 0x0},
> + {RXTX_REG53, 0x0},
> + {RXTX_REG54, 0x0},
> + {RXTX_REG55, 0x0},
> + };
> +
> + /* Start SUMMER calibration */
> + serdes_setbits(ctx, lane, RXTX_REG127,
> + RXTX_REG127_FORCE_SUM_CAL_START_MASK);
> + /*
> + * As per PHY design spec, the Summer calibration requires a minimum
> + * of 100us to complete.
> + */
> + usleep_range(100, 500);
> + serdes_clrbits(ctx, lane, RXTX_REG127,
> + RXTX_REG127_FORCE_SUM_CAL_START_MASK);
> + /*
> + * As per PHY design spec, the auto calibration requires a minimum
> + * of 100us to complete.
> + */
> + usleep_range(100, 500);
> +
> + /* Start latch calibration */
> + serdes_setbits(ctx, lane, RXTX_REG127,
> + RXTX_REG127_FORCE_LAT_CAL_START_MASK);
> + /*
> + * As per PHY design spec, the latch calibration requires a minimum
> + * of 100us to complete.
> + */
> + usleep_range(100, 500);
> + serdes_clrbits(ctx, lane, RXTX_REG127,
> + RXTX_REG127_FORCE_LAT_CAL_START_MASK);
> +
> + /* Configure the PHY lane for calibration */
> + serdes_wr(ctx, lane, RXTX_REG28, 0x7);
> + serdes_wr(ctx, lane, RXTX_REG31, 0x7e00);
> + serdes_clrbits(ctx, lane, RXTX_REG4,
> + RXTX_REG4_TX_LOOPBACK_BUF_EN_MASK);
> + serdes_clrbits(ctx, lane, RXTX_REG7,
> + RXTX_REG7_LOOP_BACK_ENA_CTLE_MASK);
> + for (i = 0; i < ARRAY_SIZE(serdes_reg); i++)
> + serdes_wr(ctx, lane, serdes_reg[i].reg,
> + serdes_reg[i].val);
> +}
> +
> +static void xgene_phy_reset_rxd(struct xgene_phy_ctx *ctx, int lane)
> +{
> + /* Reset digital Rx */
> + serdes_clrbits(ctx, lane, RXTX_REG7, RXTX_REG7_RESETB_RXD_MASK);
> + /* As per PHY design spec, the reset requires a minimum of 100us. */
> + usleep_range(100, 150);
> + serdes_setbits(ctx, lane, RXTX_REG7, RXTX_REG7_RESETB_RXD_MASK);
> +}
> +
> +static int xgene_phy_get_avg(int accum, int samples)
> +{
> + return (accum + (samples / 2)) / samples;
> +}
> +
> +static void xgene_phy_gen_avg_val(struct xgene_phy_ctx *ctx, int lane)
> +{
> + int max_loop = 10;
> + int avg_loop = 0;
> + int lat_do = 0, lat_xo = 0, lat_eo = 0, lat_so = 0;
> + int lat_de = 0, lat_xe = 0, lat_ee = 0, lat_se = 0;
> + int sum_cal = 0;
> + int lat_do_itr, lat_xo_itr, lat_eo_itr, lat_so_itr;
> + int lat_de_itr, lat_xe_itr, lat_ee_itr, lat_se_itr;
> + int sum_cal_itr;
> + int fail_even;
> + int fail_odd;
> + u32 val;
> +
> + dev_dbg(ctx->dev, "Generating avg calibration value for lane %d\n",
> + lane);
> +
> + /* Enable RX Hi-Z termination */
> + serdes_setbits(ctx, lane, RXTX_REG12,
> + RXTX_REG12_RX_DET_TERM_ENABLE_MASK);
> + /* Turn off DFE */
> + serdes_wr(ctx, lane, RXTX_REG28, 0x0000);
> + /* DFE Presets to zero */
> + serdes_wr(ctx, lane, RXTX_REG31, 0x0000);
> +
> + /*
> + * Receiver Offset Calibration:
> + * Calibrate the receiver signal path offset in two steps - summar
> + * and latch calibration.
> + * Runs the "Receiver Offset Calibration multiple times to determine
> + * the average value to use.
> + */
> + while (avg_loop < max_loop) {
> + /* Start the calibration */
> + xgene_phy_force_lat_summer_cal(ctx, lane);
> +
> + serdes_rd(ctx, lane, RXTX_REG21, &val);
> + lat_do_itr = RXTX_REG21_DO_LATCH_CALOUT_RD(val);
> + lat_xo_itr = RXTX_REG21_XO_LATCH_CALOUT_RD(val);
> + fail_odd = RXTX_REG21_LATCH_CAL_FAIL_ODD_RD(val);
> +
> + serdes_rd(ctx, lane, RXTX_REG22, &val);
> + lat_eo_itr = RXTX_REG22_EO_LATCH_CALOUT_RD(val);
> + lat_so_itr = RXTX_REG22_SO_LATCH_CALOUT_RD(val);
> + fail_even = RXTX_REG22_LATCH_CAL_FAIL_EVEN_RD(val);
> +
> + serdes_rd(ctx, lane, RXTX_REG23, &val);
> + lat_de_itr = RXTX_REG23_DE_LATCH_CALOUT_RD(val);
> + lat_xe_itr = RXTX_REG23_XE_LATCH_CALOUT_RD(val);
> +
> + serdes_rd(ctx, lane, RXTX_REG24, &val);
> + lat_ee_itr = RXTX_REG24_EE_LATCH_CALOUT_RD(val);
> + lat_se_itr = RXTX_REG24_SE_LATCH_CALOUT_RD(val);
> +
> + serdes_rd(ctx, lane, RXTX_REG121, &val);
> + sum_cal_itr = RXTX_REG121_SUMOS_CAL_CODE_RD(val);
> +
> + /* Check for failure. If passed, sum them for averaging */
> + if ((fail_even == 0 || fail_even == 1) &&
> + (fail_odd == 0 || fail_odd == 1)) {
> + lat_do += lat_do_itr;
> + lat_xo += lat_xo_itr;
> + lat_eo += lat_eo_itr;
> + lat_so += lat_so_itr;
> + lat_de += lat_de_itr;
> + lat_xe += lat_xe_itr;
> + lat_ee += lat_ee_itr;
> + lat_se += lat_se_itr;
> + sum_cal += sum_cal_itr;
> +
> + dev_dbg(ctx->dev, "Iteration %d:\n", avg_loop);
> + dev_dbg(ctx->dev, "DO 0x%x XO 0x%x EO 0x%x SO 0x%x\n",
> + lat_do_itr, lat_xo_itr, lat_eo_itr,
> + lat_so_itr);
> + dev_dbg(ctx->dev, "DE 0x%x XE 0x%x EE 0x%x SE 0x%x\n",
> + lat_de_itr, lat_xe_itr, lat_ee_itr,
> + lat_se_itr);
> + dev_dbg(ctx->dev, "SUM 0x%x\n", sum_cal_itr);
> + ++avg_loop;
> + } else {
> + dev_err(ctx->dev,
> + "Receiver calibration failed at %d loop\n",
> + avg_loop);
> + }
> + xgene_phy_reset_rxd(ctx, lane);
> + }
> +
> + /* Update latch manual calibration with average value */
> + serdes_rd(ctx, lane, RXTX_REG127, &val);
> + val = RXTX_REG127_DO_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_do, max_loop));
> + val = RXTX_REG127_XO_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_xo, max_loop));
> + serdes_wr(ctx, lane, RXTX_REG127, val);
> +
> + serdes_rd(ctx, lane, RXTX_REG128, &val);
> + val = RXTX_REG128_EO_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_eo, max_loop));
> + val = RXTX_REG128_SO_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_so, max_loop));
> + serdes_wr(ctx, lane, RXTX_REG128, val);
> +
> + serdes_rd(ctx, lane, RXTX_REG129, &val);
> + val = RXTX_REG129_DE_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_de, max_loop));
> + val = RXTX_REG129_XE_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_xe, max_loop));
> + serdes_wr(ctx, lane, RXTX_REG129, val);
> +
> + serdes_rd(ctx, lane, RXTX_REG130, &val);
> + val = RXTX_REG130_EE_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_ee, max_loop));
> + val = RXTX_REG130_SE_LATCH_MANCAL_SET(val,
> + xgene_phy_get_avg(lat_se, max_loop));
> + serdes_wr(ctx, lane, RXTX_REG130, val);
> +
> + /* Update SUMMER calibration with average value */
> + serdes_rd(ctx, lane, RXTX_REG14, &val);
> + val = RXTX_REG14_CLTE_LATCAL_MAN_PROG_SET(val,
> + xgene_phy_get_avg(sum_cal, max_loop));
> + serdes_wr(ctx, lane, RXTX_REG14, val);
> +
> + dev_dbg(ctx->dev, "Average Value:\n");
> + dev_dbg(ctx->dev, "DO 0x%x XO 0x%x EO 0x%x SO 0x%x\n",
> + xgene_phy_get_avg(lat_do, max_loop),
> + xgene_phy_get_avg(lat_xo, max_loop),
> + xgene_phy_get_avg(lat_eo, max_loop),
> + xgene_phy_get_avg(lat_so, max_loop));
> + dev_dbg(ctx->dev, "DE 0x%x XE 0x%x EE 0x%x SE 0x%x\n",
> + xgene_phy_get_avg(lat_de, max_loop),
> + xgene_phy_get_avg(lat_xe, max_loop),
> + xgene_phy_get_avg(lat_ee, max_loop),
> + xgene_phy_get_avg(lat_se, max_loop));
> + dev_dbg(ctx->dev, "SUM 0x%x\n",
> + xgene_phy_get_avg(sum_cal, max_loop));
> +
> + serdes_rd(ctx, lane, RXTX_REG14, &val);
> + val = RXTX_REG14_CTLE_LATCAL_MAN_ENA_SET(val, 0x1);
> + serdes_wr(ctx, lane, RXTX_REG14, val);
> + dev_dbg(ctx->dev, "Enable Manual Summer calibration\n");
> +
> + serdes_rd(ctx, lane, RXTX_REG127, &val);
> + val = RXTX_REG127_LATCH_MAN_CAL_ENA_SET(val, 0x1);
> + dev_dbg(ctx->dev, "Enable Manual Latch calibration\n");
> + serdes_wr(ctx, lane, RXTX_REG127, val);
> +
> + /* Disable RX Hi-Z termination */
> + serdes_rd(ctx, lane, RXTX_REG12, &val);
> + val = RXTX_REG12_RX_DET_TERM_ENABLE_SET(val, 0);
> + serdes_wr(ctx, lane, RXTX_REG12, val);
> + /* Turn on DFE */
> + serdes_wr(ctx, lane, RXTX_REG28, 0x0007);
> + /* Set DFE preset */
> + serdes_wr(ctx, lane, RXTX_REG31, 0x7e00);
> +}
> +
> +static int xgene_phy_hw_init(struct phy *phy)
> +{
> + struct xgene_phy_ctx *ctx = phy_get_drvdata(phy);
> + int rc;
> + int i;
> +
> + rc = xgene_phy_hw_initialize(ctx, CLK_EXT_DIFF, SSC_DISABLE);
> + if (rc) {
> + dev_err(ctx->dev, "PHY initialize failed %d\n", rc);
> + return rc;
> + }
> +
> + /* Setup clock properly after PHY configuration */
> + if (!IS_ERR(ctx->clk)) {
> + /* HW requires an toggle of the clock */
> + clk_prepare_enable(ctx->clk);
> + clk_disable_unprepare(ctx->clk);
> + clk_prepare_enable(ctx->clk);
> + }
> +
> + /* Compute average value */
> + for (i = 0; i < MAX_LANE; i++)
> + xgene_phy_gen_avg_val(ctx, i);
> +
> + dev_dbg(ctx->dev, "PHY initialized\n");
> + return 0;
> +}
> +
> +static const struct phy_ops xgene_phy_ops = {
> + .init = xgene_phy_hw_init,
> + .owner = THIS_MODULE,
> +};
> +
> +static struct phy *xgene_phy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct xgene_phy_ctx *ctx = dev_get_drvdata(dev);
> +
> + if (args->args_count <= 0)
> + return ERR_PTR(-EINVAL);
> + if (args->args[0] < MODE_SATA || args->args[0] >= MODE_MAX)
> + return ERR_PTR(-EINVAL);
> +
> + ctx->mode = args->args[0];
> + return ctx->phy;
> +}
> +
> +static void xgene_phy_get_param(struct platform_device *pdev,
> + const char *name, u32 *buffer,
> + int count, u32 *default_val,
> + u32 conv_factor)
> +{
> + int i;
> +
> + if (!of_property_read_u32_array(pdev->dev.of_node, name, buffer,
> + count)) {
> + for (i = 0; i < count; i++)
> + buffer[i] /= conv_factor;
> + return;
> + }
> + /* Does not exist, load default */
> + for (i = 0; i < count; i++)
> + buffer[i] = default_val[i % 3];
> +}
> +
> +static int xgene_phy_probe(struct platform_device *pdev)
> +{
> + struct phy_provider *phy_provider;
> + struct xgene_phy_ctx *ctx;
> + struct resource *res;
> + int rc = 0;
> + u32 default_spd[] = DEFAULT_SATA_SPD_SEL;
> + u32 default_txboost_gain[] = DEFAULT_SATA_TXBOOST_GAIN;
> + u32 default_txeye_direction[] = DEFAULT_SATA_TXEYEDIRECTION;
> + u32 default_txeye_tuning[] = DEFAULT_SATA_TXEYETUNING;
> + u32 default_txamp[] = DEFAULT_SATA_TXAMP;
> + u32 default_txcn1[] = DEFAULT_SATA_TXCN1;
> + u32 default_txcn2[] = DEFAULT_SATA_TXCN2;
> + u32 default_txcp1[] = DEFAULT_SATA_TXCP1;
> + int i;
> +
> + ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
> + if (!ctx)
> + return -ENOMEM;
> +
> + ctx->dev = &pdev->dev;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + ctx->sds_base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(ctx->sds_base)) {
> + rc = PTR_ERR(ctx->sds_base);
> + goto error;
> + }
> +
> + /* Retrieve optional clock */
> + ctx->clk = clk_get(&pdev->dev, NULL);
> +
> + /* Load override paramaters */
> + xgene_phy_get_param(pdev, "apm,tx-eye-tuning",
> + ctx->sata_param.txeyetuning, 6, default_txeye_tuning, 1);
> + xgene_phy_get_param(pdev, "apm,tx-eye-direction",
> + ctx->sata_param.txeyedirection, 6, default_txeye_direction, 1);
> + xgene_phy_get_param(pdev, "apm,tx-boost-gain",
> + ctx->sata_param.txboostgain, 6, default_txboost_gain, 1);
> + xgene_phy_get_param(pdev, "apm,tx-amplitude",
> + ctx->sata_param.txamplitude, 6, default_txamp, 13300);
> + xgene_phy_get_param(pdev, "apm,tx-pre-cursor1",
> + ctx->sata_param.txprecursor_cn1, 6, default_txcn1, 18200);
> + xgene_phy_get_param(pdev, "apm,tx-pre-cursor2",
> + ctx->sata_param.txprecursor_cn2, 6, default_txcn2, 18200);
> + xgene_phy_get_param(pdev, "apm,tx-post-cursor",
> + ctx->sata_param.txpostcursor_cp1, 6, default_txcp1, 18200);
> + xgene_phy_get_param(pdev, "apm,tx-speed",
> + ctx->sata_param.txspeed, 3, default_spd, 1);
> + for (i = 0; i < MAX_LANE; i++)
> + ctx->sata_param.speed[i] = 2; /* Default to Gen3 */
> +
> + ctx->dev = &pdev->dev;
> + platform_set_drvdata(pdev, ctx);
> +
> + ctx->phy = devm_phy_create(ctx->dev, &xgene_phy_ops, NULL);
> + if (IS_ERR(ctx->phy)) {
> + dev_dbg(&pdev->dev, "Failed to create PHY\n");
> + rc = PTR_ERR(ctx->phy);
> + goto error;
> + }
> + phy_set_drvdata(ctx->phy, ctx);
> +
> + phy_provider = devm_of_phy_provider_register(ctx->dev,
> + xgene_phy_xlate);
> + if (IS_ERR(phy_provider)) {
> + rc = PTR_ERR(phy_provider);
> + goto error;
> + }
> +
> + return 0;
> +
> +error:
> + return rc;
> +}
> +
> +static const struct of_device_id xgene_phy_of_match[] = {
> + {.compatible = "apm,xgene-phy",},
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, xgene_phy_of_match);
> +
> +static struct platform_driver xgene_phy_driver = {
> + .probe = xgene_phy_probe,
> + .driver = {
> + .name = "xgene-phy",
> + .owner = THIS_MODULE,
> + .of_match_table = xgene_phy_of_match,
> + },
> +};
> +module_platform_driver(xgene_phy_driver);
> +
> +MODULE_DESCRIPTION("APM X-Gene Multi-Purpose PHY driver");
> +MODULE_AUTHOR("Loc Ho <lho@....com>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_VERSION("0.1");
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists