| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1394487610-2419-4-git-send-email-soren.brinkmann@xilinx.com>
Date: Mon, 10 Mar 2014 14:40:06 -0700
From: Soren Brinkmann <soren.brinkmann@...inx.com>
To: Russell King <linux@....linux.org.uk>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Jiri Slaby <jslaby@...e.cz>,
One Thousand Gnomes <gnomes@...rguk.ukuu.org.uk>
Cc: Michal Simek <michal.simek@...inx.com>,
Peter Crosthwaite <peter.crosthwaite@...inx.com>,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-serial@...r.kernel.org, Rob Herring <robh+dt@...nel.org>,
Pawel Moll <pawel.moll@....com>,
Mark Rutland <mark.rutland@....com>,
Ian Campbell <ijc+devicetree@...lion.org.uk>,
Kumar Gala <galak@...eaurora.org>,
Rob Landley <rob@...dley.net>,
Grant Likely <grant.likely@...aro.org>,
devicetree@...r.kernel.org, linux-doc@...r.kernel.org,
Soren Brinkmann <soren.brinkmann@...inx.com>
Subject: [PATCH v2 3/7] tty: xuartps: Refactor read-modify-writes
A lot of read-modify-write sequences used a one-line statement which
nests a readl() within a writel(). Convert this into code sequences that
make the three steps more obvious.
Signed-off-by: Soren Brinkmann <soren.brinkmann@...inx.com>
---
drivers/tty/serial/xilinx_uartps.c | 52 ++++++++++++++++++--------------------
1 file changed, 24 insertions(+), 28 deletions(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index b00060052316..a4bd6242e72d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -437,9 +437,9 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
spin_lock_irqsave(&xuartps->port->lock, flags);
/* Disable the TX and RX to set baud rate */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
spin_unlock_irqrestore(&xuartps->port->lock, flags);
@@ -464,9 +464,9 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
spin_lock_irqsave(&xuartps->port->lock, flags);
/* Set TX/RX Reset */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
while (xuartps_readl(XUARTPS_CR_OFFSET) &
(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST))
@@ -479,10 +479,9 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
*/
xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- xuartps_writel(
- (ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS)) |
- (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
- XUARTPS_CR_OFFSET);
+ ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
+ ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
spin_unlock_irqrestore(&xuartps->port->lock, flags);
@@ -631,9 +630,9 @@ static void xuartps_set_termios(struct uart_port *port,
}
/* Disable the TX and RX to set baud rate */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
/*
* Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk
@@ -651,20 +650,18 @@ static void xuartps_set_termios(struct uart_port *port,
uart_update_timeout(port, termios->c_cflag, baud);
/* Set TX/RX Reset */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
- XUARTPS_CR_OFFSET);
-
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
*/
- xuartps_writel(
- (ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS))
- | (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
+ ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
@@ -1245,9 +1242,9 @@ static int xuartps_resume(struct device *device)
spin_lock_irqsave(&port->lock, flags);
/* Set TX/RX Reset */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
while (xuartps_readl(XUARTPS_CR_OFFSET) &
(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST))
cpu_relax();
@@ -1256,10 +1253,9 @@ static int xuartps_resume(struct device *device)
xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
/* Enable Tx/Rx */
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- xuartps_writel(
- (ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS)) |
- (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
- XUARTPS_CR_OFFSET);
+ ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
+ ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
} else {
--
1.9.0.1.g4196000
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists