| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <04cb5d02-db4c-4a4c-ba3c-3a5958e42324@VA3EHSMHS036.ehs.local>
Date: Thu, 27 Mar 2014 23:51:07 +0530
From: Punnaiah Choudary Kalluri <punnaiah.choudary.kalluri@...inx.com>
To: <robh+dt@...nel.org>, <pawel.moll@....com>, <mark.rutland@....com>,
<ijc+devicetree@...lion.org.uk>, <galak@...eaurora.org>,
<rob@...dley.net>, <michal.simek@...inx.com>,
<grant.likely@...aro.org>, <gregkh@...uxfoundation.org>,
<jason@...edaemon.net>, <ezequiel.garcia@...e-electrons.com>,
<arnd@...db.de>, <dwmw2@...radead.org>,
<computersforpeace@...il.com>, <artem.bityutskiy@...ux.intel.com>,
<pekon@...com>, <jussi.kivilinna@....fi>, <acourbot@...dia.com>,
<ivan.khoronzhuk@...com>, <joern@...fs.org>
CC: <devicetree@...r.kernel.org>, <linux-doc@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, <linux-mtd@...ts.infradead.org>,
<kpc528@...il.com>, <kalluripunnaiahchoudary@...il.com>,
Punnaiah Choudary Kalluri <punnaia@...inx.com>
Subject: [PATCH RFC 3/3] nand: pl353: Add driver for arm pl353 smc nand interface
Add driver for arm pl353 static memory controller nand interface.
This controller is used in xilinx zynq soc for interfacing the nand
flash memory.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@...inx.com>
---
drivers/mtd/nand/Kconfig | 8 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/pl353_nand.c | 1122 +++++++++++++++++++++++++++++++++++++++++
3 files changed, 1131 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/nand/pl353_nand.c
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 90ff447..31c1d0c 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -510,4 +510,12 @@ config MTD_NAND_XWAY
Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
to the External Bus Unit (EBU).
+config MTD_NAND_PL353
+ tristate "ARM Pl353 NAND flash driver"
+ depends on MTD_NAND && ARM
+ select PL353_SMC
+ help
+ This enables access to the NAND flash device on PL353 SMC
+ controller.
+
endif # MTD_NAND
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 542b568..a4c2679 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -49,5 +49,6 @@ obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/
obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o
obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
+obj-$(CONFIG_MTD_NAND_PL353) += pl353_nand.o
nand-objs := nand_base.o nand_bbt.o
diff --git a/drivers/mtd/nand/pl353_nand.c b/drivers/mtd/nand/pl353_nand.c
new file mode 100644
index 0000000..ee74545
--- /dev/null
+++ b/drivers/mtd/nand/pl353_nand.c
@@ -0,0 +1,1122 @@
+/*
+ * ARM PL353 NAND Flash Controller Driver
+ *
+ * Copyright (C) 2009 - 2014 Xilinx, Inc.
+ *
+ * This driver is based on plat_nand.c and mxc_nand.c drivers
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/memory/pl353-smc.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define PL353_NAND_DRIVER_NAME "pl353-nand"
+
+/* NAND flash driver defines */
+#define PL353_NAND_CMD_PHASE 1 /* End command valid in command phase */
+#define PL353_NAND_DATA_PHASE 2 /* End command valid in data phase */
+#define PL353_NAND_ECC_SIZE 512 /* Size of data for ECC operation */
+
+/* Flash memory controller operating parameters */
+
+#define PL353_NAND_ECC_CONFIG (BIT(4) | /* ECC read at end of page */ \
+ (0 << 5)) /* No Jumping */
+
+/* AXI Address definitions */
+#define START_CMD_SHIFT 3
+#define END_CMD_SHIFT 11
+#define END_CMD_VALID_SHIFT 20
+#define ADDR_CYCLES_SHIFT 21
+#define CLEAR_CS_SHIFT 21
+#define ECC_LAST_SHIFT 10
+#define COMMAND_PHASE (0 << 19)
+#define DATA_PHASE BIT(19)
+
+#define PL353_NAND_ECC_LAST BIT(ECC_LAST_SHIFT) /* Set ECC_Last */
+#define PL353_NAND_CLEAR_CS BIT(CLEAR_CS_SHIFT) /* Clear chip select */
+
+#define ONDIE_ECC_FEATURE_ADDR 0x90
+#define PL353_NAND_ECC_BUSY_TIMEOUT (1 * HZ)
+#define PL353_NAND_DEV_BUSY_TIMEOUT (1 * HZ)
+#define PL353_NAND_LAST_TRANSFER_LENGTH 4
+
+/* Inline function for the NAND controller register write */
+static inline void pl353_nand_write32(void __iomem *addr, u32 val)
+{
+ writel_relaxed((val), (addr));
+}
+
+/**
+ * struct pl353_nand_command_format - Defines NAND flash command format
+ * @start_cmd: First cycle command (Start command)
+ * @end_cmd: Second cycle command (Last command)
+ * @addr_cycles: Number of address cycles required to send the address
+ * @end_cmd_valid: The second cycle command is valid for cmd or data phase
+ */
+struct pl353_nand_command_format {
+ int start_cmd;
+ int end_cmd;
+ u8 addr_cycles;
+ u8 end_cmd_valid;
+};
+
+/**
+ * struct pl353_nand_info - Defines the NAND flash driver instance
+ * @chip: NAND chip information structure
+ * @mtd: MTD information structure
+ * @parts: Pointer to the mtd_partition structure
+ * @nand_base: Virtual address of the NAND flash device
+ * @end_cmd_pending: End command is pending
+ * @end_cmd: End command
+ */
+struct pl353_nand_info {
+ struct nand_chip chip;
+ struct mtd_info mtd;
+ struct mtd_partition *parts;
+ void __iomem *nand_base;
+ unsigned long end_cmd_pending;
+ unsigned long end_cmd;
+};
+
+/*
+ * The NAND flash operations command format
+ */
+static const struct pl353_nand_command_format pl353_nand_commands[] = {
+ {NAND_CMD_READ0, NAND_CMD_READSTART, 5, PL353_NAND_CMD_PHASE},
+ {NAND_CMD_RNDOUT, NAND_CMD_RNDOUTSTART, 2, PL353_NAND_CMD_PHASE},
+ {NAND_CMD_READID, NAND_CMD_NONE, 1, NAND_CMD_NONE},
+ {NAND_CMD_STATUS, NAND_CMD_NONE, 0, NAND_CMD_NONE},
+ {NAND_CMD_SEQIN, NAND_CMD_PAGEPROG, 5, PL353_NAND_DATA_PHASE},
+ {NAND_CMD_RNDIN, NAND_CMD_NONE, 2, NAND_CMD_NONE},
+ {NAND_CMD_ERASE1, NAND_CMD_ERASE2, 3, PL353_NAND_CMD_PHASE},
+ {NAND_CMD_RESET, NAND_CMD_NONE, 0, NAND_CMD_NONE},
+ {NAND_CMD_PARAM, NAND_CMD_NONE, 1, NAND_CMD_NONE},
+ {NAND_CMD_GET_FEATURES, NAND_CMD_NONE, 1, NAND_CMD_NONE},
+ {NAND_CMD_SET_FEATURES, NAND_CMD_NONE, 1, NAND_CMD_NONE},
+ {NAND_CMD_NONE, NAND_CMD_NONE, 0, 0},
+ /* Add all the flash commands supported by the flash device and Linux */
+ /*
+ * The cache program command is not supported by driver because driver
+ * cant differentiate between page program and cached page program from
+ * start command, these commands can be differentiated through end
+ * command, which doesn't fit in to the driver design. The cache program
+ * command is not supported by NAND subsystem also, look at 1612 line
+ * number (in nand_write_page function) of nand_base.c file.
+ * {NAND_CMD_SEQIN, NAND_CMD_CACHEDPROG, 5, PL353_NAND_YES},
+ */
+};
+
+/* Define default oob placement schemes for large and small page devices */
+static struct nand_ecclayout nand_oob_16 = {
+ .eccbytes = 3,
+ .eccpos = {0, 1, 2},
+ .oobfree = {
+ {.offset = 8,
+ . length = 8} }
+};
+
+static struct nand_ecclayout nand_oob_64 = {
+ .eccbytes = 12,
+ .eccpos = {
+ 52, 53, 54, 55, 56, 57,
+ 58, 59, 60, 61, 62, 63},
+ .oobfree = {
+ {.offset = 2,
+ .length = 50} }
+};
+
+static struct nand_ecclayout ondie_nand_oob_64 = {
+ .eccbytes = 32,
+
+ .eccpos = {
+ 8, 9, 10, 11, 12, 13, 14, 15,
+ 24, 25, 26, 27, 28, 29, 30, 31,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 56, 57, 58, 59, 60, 61, 62, 63
+ },
+
+ .oobfree = {
+ { .offset = 4, .length = 4 },
+ { .offset = 20, .length = 4 },
+ { .offset = 36, .length = 4 },
+ { .offset = 52, .length = 4 }
+ }
+};
+
+/* Generic flash bbt decriptors */
+static uint8_t bbt_pattern[] = { 'B', 'b', 't', '0' };
+static uint8_t mirror_pattern[] = { '1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 4,
+ .len = 4,
+ .veroffs = 20,
+ .maxblocks = 4,
+ .pattern = bbt_pattern
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 4,
+ .len = 4,
+ .veroffs = 20,
+ .maxblocks = 4,
+ .pattern = mirror_pattern
+};
+
+/**
+ * pl353_nand_calculate_hwecc - Calculate Hardware ECC
+ * @mtd: Pointer to the mtd_info structure
+ * @data: Pointer to the page data
+ * @ecc_code: Pointer to the ECC buffer where ECC data needs to be stored
+ *
+ * This function retrieves the Hardware ECC data from the controller and returns
+ * ECC data back to the MTD subsystem.
+ *
+ * Return: 0 on success or error value on failure
+ */
+static int pl353_nand_calculate_hwecc(struct mtd_info *mtd,
+ const u8 *data, u8 *ecc_code)
+{
+ u32 ecc_value, ecc_status;
+ u8 ecc_reg, ecc_byte;
+ unsigned long timeout = jiffies + PL353_NAND_ECC_BUSY_TIMEOUT;
+
+ /* Wait till the ECC operation is complete or timeout */
+ do {
+ if (pl353_smc_ecc_is_busy())
+ cpu_relax();
+ else
+ break;
+ } while (!time_after_eq(jiffies, timeout));
+
+ if (time_after_eq(jiffies, timeout)) {
+ pr_err("%s timed out\n", __func__);
+ return -ETIMEDOUT;
+ }
+
+ for (ecc_reg = 0; ecc_reg < 4; ecc_reg++) {
+ /* Read ECC value for each block */
+ ecc_value = pl353_smc_get_ecc_val(ecc_reg);
+ ecc_status = (ecc_value >> 24) & 0xFF;
+ /* ECC value valid */
+ if (ecc_status & 0x40) {
+ for (ecc_byte = 0; ecc_byte < 3; ecc_byte++) {
+ /* Copy ECC bytes to MTD buffer */
+ *ecc_code = ecc_value & 0xFF;
+ ecc_value = ecc_value >> 8;
+ ecc_code++;
+ }
+ } else {
+ pr_warn("%s status failed\n", __func__);
+ return -1;
+ }
+ }
+ return 0;
+}
+
+/**
+ * onehot - onehot function
+ * @value: Value to check for onehot
+ *
+ * This function checks whether a value is onehot or not.
+ * onehot is if and only if onebit is set.
+ *
+ * Return: 1 if it is onehot else 0
+ */
+static int onehot(unsigned short value)
+{
+ return (value & (value - 1)) == 0;
+}
+
+/**
+ * pl353_nand_correct_data - ECC correction function
+ * @mtd: Pointer to the mtd_info structure
+ * @buf: Pointer to the page data
+ * @read_ecc: Pointer to the ECC value read from spare data area
+ * @calc_ecc: Pointer to the calculated ECC value
+ *
+ * This function corrects the ECC single bit errors & detects 2-bit errors.
+ *
+ * Return: 0 if no ECC errors found
+ * 1 if single bit error found and corrected.
+ * -1 if multiple ECC errors found.
+ */
+static int pl353_nand_correct_data(struct mtd_info *mtd, unsigned char *buf,
+ unsigned char *read_ecc,
+ unsigned char *calc_ecc)
+{
+ unsigned char bit_addr;
+ unsigned int byte_addr;
+ unsigned short ecc_odd, ecc_even, read_ecc_lower, read_ecc_upper;
+ unsigned short calc_ecc_lower, calc_ecc_upper;
+
+ read_ecc_lower = (read_ecc[0] | (read_ecc[1] << 8)) & 0xfff;
+ read_ecc_upper = ((read_ecc[1] >> 4) | (read_ecc[2] << 4)) & 0xfff;
+
+ calc_ecc_lower = (calc_ecc[0] | (calc_ecc[1] << 8)) & 0xfff;
+ calc_ecc_upper = ((calc_ecc[1] >> 4) | (calc_ecc[2] << 4)) & 0xfff;
+
+ ecc_odd = read_ecc_lower ^ calc_ecc_lower;
+ ecc_even = read_ecc_upper ^ calc_ecc_upper;
+
+ if ((ecc_odd == 0) && (ecc_even == 0))
+ return 0; /* no error */
+
+ if (ecc_odd == (~ecc_even & 0xfff)) {
+ /* bits [11:3] of error code is byte offset */
+ byte_addr = (ecc_odd >> 3) & 0x1ff;
+ /* bits [2:0] of error code is bit offset */
+ bit_addr = ecc_odd & 0x7;
+ /* Toggling error bit */
+ buf[byte_addr] ^= (1 << bit_addr);
+ return 1;
+ }
+
+ if (onehot(ecc_odd | ecc_even) == 1)
+ return 1; /* one error in parity */
+
+ return -1; /* Uncorrectable error */
+}
+
+/**
+ * pl353_nand_read_oob - [REPLACABLE] the most common OOB data read function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @page: Page number to read
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ unsigned long data_phase_addr;
+ uint8_t *p;
+
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
+
+ p = chip->oob_poi;
+ chip->read_buf(mtd, p,
+ (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+ chip->read_buf(mtd, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_write_oob - [REPLACABLE] the most common OOB data write function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @page: Page number to write
+ *
+ * Return: Zero on success and EIO on failure
+ */
+static int pl353_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ int status = 0;
+ const uint8_t *buf = chip->oob_poi;
+ unsigned long data_phase_addr;
+
+ chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page);
+
+ chip->write_buf(mtd, buf,
+ (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ buf += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr |= (1 << END_CMD_VALID_SHIFT);
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+ chip->write_buf(mtd, buf, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Send command to program the OOB data */
+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+ status = chip->waitfunc(mtd, chip);
+
+ return status & NAND_STATUS_FAIL ? -EIO : 0;
+}
+
+/**
+ * pl353_nand_read_page_raw - [Intern] read raw page data without ecc
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the data buffer
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ * @page: Page number to read
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_read_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ unsigned long data_phase_addr;
+ uint8_t *p;
+
+ chip->read_buf(mtd, buf, mtd->writesize);
+
+ p = chip->oob_poi;
+ chip->read_buf(mtd, p,
+ (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+
+ chip->read_buf(mtd, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+ return 0;
+}
+
+/**
+ * pl353_nand_write_page_raw - [Intern] raw page write function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the data buffer
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_write_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
+{
+ unsigned long data_phase_addr;
+ uint8_t *p;
+
+ chip->write_buf(mtd, buf, mtd->writesize);
+
+ p = chip->oob_poi;
+ chip->write_buf(mtd, p,
+ (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr |= (1 << END_CMD_VALID_SHIFT);
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+
+ chip->write_buf(mtd, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ return 0;
+}
+
+/**
+ * nand_write_page_hwecc - Hardware ECC based page write function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the data buffer
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ *
+ * This functions writes data and hardware generated ECC values in to the page.
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf,
+ int oob_required)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ const uint8_t *p = buf;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ unsigned long data_phase_addr;
+ uint8_t *oob_ptr;
+
+ for ( ; (eccsteps - 1); eccsteps--) {
+ chip->write_buf(mtd, p, eccsize);
+ p += eccsize;
+ }
+ chip->write_buf(mtd, p, (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Set ECC Last bit to 1 */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr |= PL353_NAND_ECC_LAST;
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+ chip->write_buf(mtd, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Wait for ECC to be calculated and read the error values */
+ p = buf;
+ chip->ecc.calculate(mtd, p, &ecc_calc[0]);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ chip->oob_poi[eccpos[i]] = ~(ecc_calc[i]);
+
+ /* Clear ECC last bit */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr &= ~PL353_NAND_ECC_LAST;
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+
+ /* Write the spare area with ECC bytes */
+ oob_ptr = chip->oob_poi;
+ chip->write_buf(mtd, oob_ptr,
+ (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr |= (1 << END_CMD_VALID_SHIFT);
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+ oob_ptr += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+ chip->write_buf(mtd, oob_ptr, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_write_page_swecc - [REPLACABLE] software ecc based page write function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the data buffer
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_write_page_swecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf,
+ int oob_required)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ const uint8_t *p = buf;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+
+ /* Software ecc calculation */
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ chip->oob_poi[eccpos[i]] = ecc_calc[i];
+
+ chip->ecc.write_page_raw(mtd, chip, buf, 1);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_read_page_hwecc - Hardware ECC based page read function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the buffer to store read data
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ * @page: Page number to read
+ *
+ * This functions reads data and checks the data integrity by comparing hardware
+ * generated ECC values and read ECC values from spare area.
+ *
+ * Return: 0 always and updates ECC operation status in to MTD structure
+ */
+static int pl353_nand_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ int i, stat, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ unsigned long data_phase_addr;
+ uint8_t *oob_ptr;
+
+ for ( ; (eccsteps - 1); eccsteps--) {
+ chip->read_buf(mtd, p, eccsize);
+ p += eccsize;
+ }
+ chip->read_buf(mtd, p, (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Set ECC Last bit to 1 */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr |= PL353_NAND_ECC_LAST;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+ chip->read_buf(mtd, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Read the calculated ECC value */
+ p = buf;
+ chip->ecc.calculate(mtd, p, &ecc_calc[0]);
+
+ /* Clear ECC last bit */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr &= ~PL353_NAND_ECC_LAST;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+
+ /* Read the stored ECC value */
+ oob_ptr = chip->oob_poi;
+ chip->read_buf(mtd, oob_ptr,
+ (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+
+ /* de-assert chip select */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+
+ oob_ptr += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+ chip->read_buf(mtd, oob_ptr, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = ~(chip->oob_poi[eccpos[i]]);
+
+ eccsteps = chip->ecc.steps;
+ p = buf;
+
+ /* Check ECC error for all blocks and correct if it is correctable */
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ if (stat < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += stat;
+ }
+ return 0;
+}
+
+/**
+ * pl353_nand_read_page_swecc - [REPLACABLE] software ecc based page read function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the buffer to store read data
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ * @page: Page number to read
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_read_page_swecc(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+
+ chip->ecc.read_page_raw(mtd, chip, buf, page, 1);
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = chip->oob_poi[eccpos[i]];
+
+ eccsteps = chip->ecc.steps;
+ p = buf;
+
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ if (stat < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += stat;
+ }
+ return 0;
+}
+
+/**
+ * pl353_nand_select_chip - Select the flash device
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ *
+ * This function is empty as the NAND controller handles chip select line
+ * internally based on the chip address passed in command and data phase.
+ */
+static void pl353_nand_select_chip(struct mtd_info *mtd, int chip)
+{
+ return;
+}
+
+/**
+ * pl353_nand_cmd_function - Send command to NAND device
+ * @mtd: Pointer to the mtd_info structure
+ * @command: The command to be sent to the flash device
+ * @column: The column address for this command, -1 if none
+ * @page_addr: The page address for this command, -1 if none
+ */
+static void pl353_nand_cmd_function(struct mtd_info *mtd, unsigned int command,
+ int column, int page_addr)
+{
+ struct nand_chip *chip = mtd->priv;
+ const struct pl353_nand_command_format *curr_cmd = NULL;
+ struct pl353_nand_info *xnand =
+ container_of(mtd, struct pl353_nand_info, mtd);
+ void __iomem *cmd_addr;
+ unsigned long cmd_data = 0, end_cmd_valid = 0;
+ unsigned long cmd_phase_addr, data_phase_addr, end_cmd, i;
+ unsigned long timeout = jiffies + PL353_NAND_DEV_BUSY_TIMEOUT;
+
+ if (xnand->end_cmd_pending) {
+ /*
+ * Check for end command if this command request is same as the
+ * pending command then return
+ */
+ if (xnand->end_cmd == command) {
+ xnand->end_cmd = 0;
+ xnand->end_cmd_pending = 0;
+ return;
+ }
+ }
+
+ /* Emulate NAND_CMD_READOOB for large page device */
+ if ((mtd->writesize > PL353_NAND_ECC_SIZE) &&
+ (command == NAND_CMD_READOOB)) {
+ column += mtd->writesize;
+ command = NAND_CMD_READ0;
+ }
+
+ /* Get the command format */
+ for (i = 0; (pl353_nand_commands[i].start_cmd != NAND_CMD_NONE ||
+ pl353_nand_commands[i].end_cmd != NAND_CMD_NONE); i++)
+ if (command == pl353_nand_commands[i].start_cmd)
+ curr_cmd = &pl353_nand_commands[i];
+
+ if (curr_cmd == NULL)
+ return;
+
+ /* Clear interrupt */
+ pl353_smc_clr_nand_int();
+
+ /* Get the command phase address */
+ if (curr_cmd->end_cmd_valid == PL353_NAND_CMD_PHASE)
+ end_cmd_valid = 1;
+
+ if (curr_cmd->end_cmd == NAND_CMD_NONE)
+ end_cmd = 0x0;
+ else
+ end_cmd = curr_cmd->end_cmd;
+
+ cmd_phase_addr = (unsigned long __force)xnand->nand_base |
+ (curr_cmd->addr_cycles << ADDR_CYCLES_SHIFT) |
+ (end_cmd_valid << END_CMD_VALID_SHIFT) |
+ (COMMAND_PHASE) |
+ (end_cmd << END_CMD_SHIFT) |
+ (curr_cmd->start_cmd << START_CMD_SHIFT);
+
+ cmd_addr = (void __iomem * __force)cmd_phase_addr;
+
+ /* Get the data phase address */
+ end_cmd_valid = 0;
+
+ data_phase_addr = (unsigned long __force)xnand->nand_base |
+ (0x0 << CLEAR_CS_SHIFT) |
+ (end_cmd_valid << END_CMD_VALID_SHIFT) |
+ (DATA_PHASE) |
+ (end_cmd << END_CMD_SHIFT) |
+ (0x0 << ECC_LAST_SHIFT);
+
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+ chip->IO_ADDR_W = chip->IO_ADDR_R;
+
+ /* Command phase AXI write */
+ /* Read & Write */
+ if (column != -1 && page_addr != -1) {
+ /* Adjust columns for 16 bit bus width */
+ if (chip->options & NAND_BUSWIDTH_16)
+ column >>= 1;
+ cmd_data = column;
+ if (mtd->writesize > PL353_NAND_ECC_SIZE) {
+ cmd_data |= page_addr << 16;
+ /* Another address cycle for devices > 128MiB */
+ if (chip->chipsize > (128 << 20)) {
+ pl353_nand_write32(cmd_addr, cmd_data);
+ cmd_data = (page_addr >> 16);
+ }
+ } else {
+ cmd_data |= page_addr << 8;
+ }
+ } else if (page_addr != -1) {
+ /* Erase */
+ cmd_data = page_addr;
+ } else if (column != -1) {
+ /*
+ * Change read/write column, read id etc
+ * Adjust columns for 16 bit bus width
+ */
+ if ((chip->options & NAND_BUSWIDTH_16) &&
+ ((command == NAND_CMD_READ0) ||
+ (command == NAND_CMD_SEQIN) ||
+ (command == NAND_CMD_RNDOUT) ||
+ (command == NAND_CMD_RNDIN)))
+ column >>= 1;
+ cmd_data = column;
+ }
+
+ pl353_nand_write32(cmd_addr, cmd_data);
+
+ if (curr_cmd->end_cmd_valid) {
+ xnand->end_cmd = curr_cmd->end_cmd;
+ xnand->end_cmd_pending = 1;
+ }
+
+ ndelay(100);
+
+ if ((command == NAND_CMD_READ0) ||
+ (command == NAND_CMD_RESET) ||
+ (command == NAND_CMD_PARAM) ||
+ (command == NAND_CMD_GET_FEATURES)) {
+
+ /* Wait till the device is ready or timeout */
+ do {
+ if (chip->dev_ready(mtd))
+ break;
+ else
+ cpu_relax();
+ } while (!time_after_eq(jiffies, timeout));
+
+ if (time_after_eq(jiffies, timeout))
+ pr_err("%s timed out\n", __func__);
+ return;
+ }
+}
+
+/**
+ * pl353_nand_read_buf - read chip data into buffer
+ * @mtd: Pointer to the mtd info structure
+ * @buf: Pointer to the buffer to store read data
+ * @len: Number of bytes to read
+ */
+static void pl353_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ int i;
+ struct nand_chip *chip = mtd->priv;
+ unsigned long *ptr = (unsigned long *)buf;
+
+ len >>= 2;
+ for (i = 0; i < len; i++)
+ ptr[i] = readl(chip->IO_ADDR_R);
+}
+
+/**
+ * pl353_nand_write_buf - write buffer to chip
+ * @mtd: Pointer to the mtd info structure
+ * @buf: Pointer to the buffer to store read data
+ * @len: Number of bytes to write
+ */
+static void pl353_nand_write_buf(struct mtd_info *mtd, const uint8_t *buf,
+ int len)
+{
+ int i;
+ struct nand_chip *chip = mtd->priv;
+ unsigned long *ptr = (unsigned long *)buf;
+
+ len >>= 2;
+
+ for (i = 0; i < len; i++)
+ writel(ptr[i], chip->IO_ADDR_W);
+}
+
+/**
+ * pl353_nand_device_ready - Check device ready/busy line
+ * @mtd: Pointer to the mtd_info structure
+ *
+ * Return: 0 on busy or 1 on ready state
+ */
+static int pl353_nand_device_ready(struct mtd_info *mtd)
+{
+ if (pl353_smc_get_nand_int_status_raw()) {
+ pl353_smc_clr_nand_int();
+ return 1;
+ }
+ return 0;
+}
+
+/**
+ * pl353_nand_detect_ondie_ecc - Get the flash ondie ecc state
+ * @mtd: Pointer to the mtd_info structure
+ *
+ * This function enables the ondie ecc for the Micron ondie ecc capable devices
+ *
+ * Return: 1 on detect, 0 if fail to detect
+ */
+static int pl353_nand_detect_ondie_ecc(struct mtd_info *mtd)
+{
+ struct nand_chip *nand_chip = mtd->priv;
+ u8 maf_id, dev_id, i, get_feature;
+ u8 set_feature[4] = { 0x08, 0x00, 0x00, 0x00 };
+
+ /* Check if On-Die ECC flash */
+ nand_chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ nand_chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
+
+ /* Read manufacturer and device IDs */
+ maf_id = readb(nand_chip->IO_ADDR_R);
+ dev_id = readb(nand_chip->IO_ADDR_R);
+
+ if ((maf_id == NAND_MFR_MICRON) &&
+ ((dev_id == 0xf1) || (dev_id == 0xa1) ||
+ (dev_id == 0xb1) || (dev_id == 0xaa) ||
+ (dev_id == 0xba) || (dev_id == 0xda) ||
+ (dev_id == 0xca) || (dev_id == 0xac) ||
+ (dev_id == 0xbc) || (dev_id == 0xdc) ||
+ (dev_id == 0xcc) || (dev_id == 0xa3) ||
+ (dev_id == 0xb3) ||
+ (dev_id == 0xd3) || (dev_id == 0xc3))) {
+
+ nand_chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES,
+ ONDIE_ECC_FEATURE_ADDR, -1);
+ get_feature = readb(nand_chip->IO_ADDR_R);
+
+ if (get_feature & 0x08) {
+ return 1;
+ } else {
+ nand_chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES,
+ ONDIE_ECC_FEATURE_ADDR, -1);
+ for (i = 0; i < 4; i++)
+ writeb(set_feature[i], nand_chip->IO_ADDR_W);
+
+ ndelay(1000);
+
+ nand_chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES,
+ ONDIE_ECC_FEATURE_ADDR, -1);
+ get_feature = readb(nand_chip->IO_ADDR_R);
+
+ if (get_feature & 0x08)
+ return 1;
+
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * pl353_nand_ecc_init - Initialize the ecc information as per the ecc mode
+ * @mtd: Pointer to the mtd_info structure
+ * @ondie_ecc_state: ondie ecc status
+ *
+ * This function initializes the ecc block and functional pointers as per the
+ * ecc mode
+ */
+static void pl353_nand_ecc_init(struct mtd_info *mtd, int ondie_ecc_state)
+{
+ struct nand_chip *nand_chip = mtd->priv;
+
+ nand_chip->ecc.mode = NAND_ECC_HW;
+ nand_chip->ecc.read_oob = pl353_nand_read_oob;
+ nand_chip->ecc.read_page_raw = pl353_nand_read_page_raw;
+ nand_chip->ecc.strength = 1;
+ nand_chip->ecc.write_oob = pl353_nand_write_oob;
+ nand_chip->ecc.write_page_raw = pl353_nand_write_page_raw;
+
+ if (ondie_ecc_state) {
+ /* bypass the controller ECC block */
+ pl353_smc_set_ecc_mode(PL353_SMC_ECCMODE_BYPASS);
+
+ /*
+ * The software ECC routines won't work with the
+ * SMC controller
+ */
+ nand_chip->ecc.bytes = 0;
+ nand_chip->ecc.layout = &ondie_nand_oob_64;
+ nand_chip->ecc.read_page = pl353_nand_read_page_raw;
+ nand_chip->ecc.write_page = pl353_nand_write_page_raw;
+ nand_chip->ecc.size = mtd->writesize;
+ /*
+ * On-Die ECC spare bytes offset 8 is used for ECC codes
+ * Use the BBT pattern descriptors
+ */
+ nand_chip->bbt_td = &bbt_main_descr;
+ nand_chip->bbt_md = &bbt_mirror_descr;
+ } else {
+ /* Hardware ECC generates 3 bytes ECC code for each 512 bytes */
+ nand_chip->ecc.bytes = 3;
+ nand_chip->ecc.calculate = pl353_nand_calculate_hwecc;
+ nand_chip->ecc.correct = pl353_nand_correct_data;
+ nand_chip->ecc.hwctl = NULL;
+ nand_chip->ecc.read_page = pl353_nand_read_page_hwecc;
+ nand_chip->ecc.size = PL353_NAND_ECC_SIZE;
+ nand_chip->ecc.write_page = pl353_nand_write_page_hwecc;
+
+ pl353_smc_set_ecc_pg_size(mtd->writesize);
+ switch (mtd->writesize) {
+ case 512:
+ case 1024:
+ case 2048:
+ pl353_smc_set_ecc_mode(PL353_SMC_ECCMODE_APB);
+ break;
+ default:
+ /*
+ * The software ECC routines won't work with the
+ * SMC controller
+ */
+ nand_chip->ecc.calculate = nand_calculate_ecc;
+ nand_chip->ecc.correct = nand_correct_data;
+ nand_chip->ecc.read_page = pl353_nand_read_page_swecc;
+ nand_chip->ecc.write_page = pl353_nand_write_page_swecc;
+ nand_chip->ecc.size = 256;
+ break;
+ }
+
+ if (mtd->oobsize == 16)
+ nand_chip->ecc.layout = &nand_oob_16;
+ else if (mtd->oobsize == 64)
+ nand_chip->ecc.layout = &nand_oob_64;
+ }
+}
+
+/**
+ * pl353_nand_probe - Probe method for the NAND driver
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function initializes the driver data structures and the hardware.
+ *
+ * Return: 0 on success or error value on failure
+ */
+static int pl353_nand_probe(struct platform_device *pdev)
+{
+ struct pl353_nand_info *xnand;
+ struct mtd_info *mtd;
+ struct nand_chip *nand_chip;
+ struct resource *res;
+ struct mtd_part_parser_data ppdata;
+ int ondie_ecc_state;
+
+ xnand = devm_kzalloc(&pdev->dev, sizeof(*xnand), GFP_KERNEL);
+ if (!xnand)
+ return -ENOMEM;
+
+ /* Map physical address of NAND flash */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ xnand->nand_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(xnand->nand_base))
+ return PTR_ERR(xnand->nand_base);
+
+ /* Link the private data with the MTD structure */
+ mtd = &xnand->mtd;
+ nand_chip = &xnand->chip;
+
+ nand_chip->priv = xnand;
+ mtd->priv = nand_chip;
+ mtd->owner = THIS_MODULE;
+ mtd->name = PL353_NAND_DRIVER_NAME;
+
+ /* Set address of NAND IO lines */
+ nand_chip->IO_ADDR_R = xnand->nand_base;
+ nand_chip->IO_ADDR_W = xnand->nand_base;
+
+ /* Set the driver entry points for MTD */
+ nand_chip->cmdfunc = pl353_nand_cmd_function;
+ nand_chip->dev_ready = pl353_nand_device_ready;
+ nand_chip->select_chip = pl353_nand_select_chip;
+
+ /* If we don't set this delay driver sets 20us by default */
+ nand_chip->chip_delay = 30;
+
+ /* Buffer read/write routines */
+ nand_chip->read_buf = pl353_nand_read_buf;
+ nand_chip->write_buf = pl353_nand_write_buf;
+
+ /* Set the device option and flash width */
+ nand_chip->options = NAND_BUSWIDTH_AUTO;
+ nand_chip->bbt_options = NAND_BBT_USE_FLASH;
+
+ platform_set_drvdata(pdev, xnand);
+
+ ondie_ecc_state = pl353_nand_detect_ondie_ecc(mtd);
+
+ /* first scan to find the device and get the page size */
+ if (nand_scan_ident(mtd, 1, NULL)) {
+ dev_err(&pdev->dev, "nand_scan_ident for NAND failed\n");
+ return -ENXIO;
+ }
+
+ pl353_nand_ecc_init(mtd, ondie_ecc_state);
+ if (nand_chip->options & NAND_BUSWIDTH_16)
+ pl353_smc_set_buswidth(PL353_SMC_MEM_WIDTH_16);
+
+ /* second phase scan */
+ if (nand_scan_tail(mtd)) {
+ dev_err(&pdev->dev, "nand_scan_tail for NAND failed\n");
+ return -ENXIO;
+ }
+
+ ppdata.of_node = pdev->dev.of_node;
+
+ mtd_device_parse_register(&xnand->mtd, NULL, &ppdata, NULL, 0);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_remove - Remove method for the NAND driver
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function is called if the driver module is being unloaded. It frees all
+ * resources allocated to the device.
+ *
+ * Return: 0 on success or error value on failure
+ */
+static int pl353_nand_remove(struct platform_device *pdev)
+{
+ struct pl353_nand_info *xnand = platform_get_drvdata(pdev);
+
+ /* Release resources, unregister device */
+ nand_release(&xnand->mtd);
+ /* kfree(NULL) is safe */
+ kfree(xnand->parts);
+
+ return 0;
+}
+
+/* Match table for device tree binding */
+static const struct of_device_id pl353_nand_of_match[] = {
+ { .compatible = "arm,pl353-nand-r2p1" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, pl353_nand_of_match);
+
+/*
+ * pl353_nand_driver - This structure defines the NAND subsystem platform driver
+ */
+static struct platform_driver pl353_nand_driver = {
+ .probe = pl353_nand_probe,
+ .remove = pl353_nand_remove,
+ .driver = {
+ .name = PL353_NAND_DRIVER_NAME,
+ .owner = THIS_MODULE,
+ .of_match_table = pl353_nand_of_match,
+ },
+};
+
+module_platform_driver(pl353_nand_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_ALIAS("platform:" PL353_NAND_DRIVER_NAME);
+MODULE_DESCRIPTION("ARM PL353 NAND Flash Driver");
+MODULE_LICENSE("GPL");
--
1.7.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists