Date:	Tue, 15 Apr 2014 13:36:23 +0200
From:	Paul Bolle <pebolle@...cali.nl>
To:	Felipe Balbi <balbi@...com>,
	Greg Kroah-Hartman <gregkh@...uxfoundation.org>
Cc:	Richard Weinberger <richard@....at>, linux-kernel@...r.kernel.org,
	linux-usb@...r.kernel.org
Subject: [PATCH] usb: phy: mv_u3d: Remove usb phy driver for mv_u3d

The usb phy driver for mv_u3d got added in v3.7 through commit
a67e76ac904c ("usb: phy: mv_u3d: Add usb phy driver for mv_u3d"). It
then depended on USB_MV_U3D. And that symbol depended
on CPU_MMP3 at that time. But CPU_MMP3 has never been part of the tree.
This means that this drive was unbuildable when it was added.

In commit 60630c2eabd4 ("usb: gadget: mv_u3d: drop ARCH dependency")
MV_U3D_PHY was made depended directly on CPU_MMP3. That kept it
unbuildable, of course.

Remove this driver. It can be re-added once its dependencies are part of
the tree.

Signed-off-by: Paul Bolle <pebolle@...cali.nl>
---
Tested with git grep.

This was triggered by Richard's "[PATCH 01/28] Remove CPU_MMP3" of two
months ago, which I acked to eagerly. See
https://lkml.org/lkml/2014/2/11/714 for the details.

 drivers/usb/phy/Kconfig          |   8 -
 drivers/usb/phy/Makefile         |   1 -
 drivers/usb/phy/phy-mv-u3d-usb.c | 338 ---------------------------------------
 drivers/usb/phy/phy-mv-u3d-usb.h | 105 ------------
 4 files changed, 452 deletions(-)
 delete mode 100644 drivers/usb/phy/phy-mv-u3d-usb.c
 delete mode 100644 drivers/usb/phy/phy-mv-u3d-usb.h

diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 416e0c8cf6ff..33dd6a6c320a 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -59,14 +59,6 @@ config KEYSTONE_USB_PHY
 	  interface to interact with USB 2.0 and USB 3.0 PHY that is part
 	  of the Keystone SOC.
 
-config MV_U3D_PHY
-	bool "Marvell USB 3.0 PHY controller Driver"
-	depends on CPU_MMP3
-	select USB_PHY
-	help
-	  Enable this to support Marvell USB 3.0 phy controller for Marvell
-	  SoC.
-
 config NOP_USB_XCEIV
 	tristate "NOP USB Transceiver Driver"
 	select USB_PHY
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index f8fa719a31b9..a2d05690d925 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -10,7 +10,6 @@ obj-$(CONFIG_USB_OTG_FSM)		+= phy-fsm-usb.o
 obj-$(CONFIG_AB8500_USB)		+= phy-ab8500-usb.o
 obj-$(CONFIG_FSL_USB2_OTG)		+= phy-fsl-usb.o
 obj-$(CONFIG_ISP1301_OMAP)		+= phy-isp1301-omap.o
-obj-$(CONFIG_MV_U3D_PHY)		+= phy-mv-u3d-usb.o
 obj-$(CONFIG_NOP_USB_XCEIV)		+= phy-generic.o
 obj-$(CONFIG_TAHVO_USB)			+= phy-tahvo.o
 obj-$(CONFIG_AM335X_CONTROL_USB)	+= phy-am335x-control.o
diff --git a/drivers/usb/phy/phy-mv-u3d-usb.c b/drivers/usb/phy/phy-mv-u3d-usb.c
deleted file mode 100644
index d317903022bf..000000000000
--- a/drivers/usb/phy/phy-mv-u3d-usb.c
+++ /dev/null
@@ -1,338 +0,0 @@
-/*
- * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/usb/otg.h>
-#include <linux/platform_data/mv_usb.h>
-
-#include "phy-mv-u3d-usb.h"
-
-/*
- * struct mv_u3d_phy - transceiver driver state
- * @phy: transceiver structure
- * @dev: The parent device supplied to the probe function
- * @clk: usb phy clock
- * @base: usb phy register memory base
- */
-struct mv_u3d_phy {
-	struct usb_phy	phy;
-	struct mv_usb_platform_data *plat;
-	struct device	*dev;
-	struct clk	*clk;
-	void __iomem	*base;
-};
-
-static u32 mv_u3d_phy_read(void __iomem *base, u32 reg)
-{
-	void __iomem *addr, *data;
-
-	addr = base;
-	data = base + 0x4;
-
-	writel_relaxed(reg, addr);
-	return readl_relaxed(data);
-}
-
-static void mv_u3d_phy_set(void __iomem *base, u32 reg, u32 value)
-{
-	void __iomem *addr, *data;
-	u32 tmp;
-
-	addr = base;
-	data = base + 0x4;
-
-	writel_relaxed(reg, addr);
-	tmp = readl_relaxed(data);
-	tmp |= value;
-	writel_relaxed(tmp, data);
-}
-
-static void mv_u3d_phy_clear(void __iomem *base, u32 reg, u32 value)
-{
-	void __iomem *addr, *data;
-	u32 tmp;
-
-	addr = base;
-	data = base + 0x4;
-
-	writel_relaxed(reg, addr);
-	tmp = readl_relaxed(data);
-	tmp &= ~value;
-	writel_relaxed(tmp, data);
-}
-
-static void mv_u3d_phy_write(void __iomem *base, u32 reg, u32 value)
-{
-	void __iomem *addr, *data;
-
-	addr = base;
-	data = base + 0x4;
-
-	writel_relaxed(reg, addr);
-	writel_relaxed(value, data);
-}
-
-static void mv_u3d_phy_shutdown(struct usb_phy *phy)
-{
-	struct mv_u3d_phy *mv_u3d_phy;
-	void __iomem *base;
-	u32 val;
-
-	mv_u3d_phy = container_of(phy, struct mv_u3d_phy, phy);
-	base = mv_u3d_phy->base;
-
-	/* Power down Reference Analog current, bit 15
-	 * Power down PLL, bit 14
-	 * Power down Receiver, bit 13
-	 * Power down Transmitter, bit 12
-	 * of USB3_POWER_PLL_CONTROL register
-	 */
-	val = mv_u3d_phy_read(base, USB3_POWER_PLL_CONTROL);
-	val &= ~(USB3_POWER_PLL_CONTROL_PU);
-	mv_u3d_phy_write(base, USB3_POWER_PLL_CONTROL, val);
-
-	if (mv_u3d_phy->clk)
-		clk_disable(mv_u3d_phy->clk);
-}
-
-static int mv_u3d_phy_init(struct usb_phy *phy)
-{
-	struct mv_u3d_phy *mv_u3d_phy;
-	void __iomem *base;
-	u32 val, count;
-
-	/* enable usb3 phy */
-	mv_u3d_phy = container_of(phy, struct mv_u3d_phy, phy);
-
-	if (mv_u3d_phy->clk)
-		clk_enable(mv_u3d_phy->clk);
-
-	base = mv_u3d_phy->base;
-
-	val = mv_u3d_phy_read(base, USB3_POWER_PLL_CONTROL);
-	val &= ~(USB3_POWER_PLL_CONTROL_PU_MASK);
-	val |= 0xF << USB3_POWER_PLL_CONTROL_PU_SHIFT;
-	mv_u3d_phy_write(base, USB3_POWER_PLL_CONTROL, val);
-	udelay(100);
-
-	mv_u3d_phy_write(base, USB3_RESET_CONTROL,
-			USB3_RESET_CONTROL_RESET_PIPE);
-	udelay(100);
-
-	mv_u3d_phy_write(base, USB3_RESET_CONTROL,
-			USB3_RESET_CONTROL_RESET_PIPE
-			| USB3_RESET_CONTROL_RESET_PHY);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_POWER_PLL_CONTROL);
-	val &= ~(USB3_POWER_PLL_CONTROL_REF_FREF_SEL_MASK
-		| USB3_POWER_PLL_CONTROL_PHY_MODE_MASK);
-	val |=  (USB3_PLL_25MHZ << USB3_POWER_PLL_CONTROL_REF_FREF_SEL_SHIFT)
-		| (0x5 << USB3_POWER_PLL_CONTROL_PHY_MODE_SHIFT);
-	mv_u3d_phy_write(base, USB3_POWER_PLL_CONTROL, val);
-	udelay(100);
-
-	mv_u3d_phy_clear(base, USB3_KVCO_CALI_CONTROL,
-		USB3_KVCO_CALI_CONTROL_USE_MAX_PLL_RATE_MASK);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_SQUELCH_FFE);
-	val &= ~(USB3_SQUELCH_FFE_FFE_CAP_SEL_MASK
-		| USB3_SQUELCH_FFE_FFE_RES_SEL_MASK
-		| USB3_SQUELCH_FFE_SQ_THRESH_IN_MASK);
-	val |= ((0xD << USB3_SQUELCH_FFE_FFE_CAP_SEL_SHIFT)
-		| (0x7 << USB3_SQUELCH_FFE_FFE_RES_SEL_SHIFT)
-		| (0x8 << USB3_SQUELCH_FFE_SQ_THRESH_IN_SHIFT));
-	mv_u3d_phy_write(base, USB3_SQUELCH_FFE, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_GEN1_SET0);
-	val &= ~USB3_GEN1_SET0_G1_TX_SLEW_CTRL_EN_MASK;
-	val |= 1 << USB3_GEN1_SET0_G1_TX_EMPH_EN_SHIFT;
-	mv_u3d_phy_write(base, USB3_GEN1_SET0, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_GEN2_SET0);
-	val &= ~(USB3_GEN2_SET0_G2_TX_AMP_MASK
-		| USB3_GEN2_SET0_G2_TX_EMPH_AMP_MASK
-		| USB3_GEN2_SET0_G2_TX_SLEW_CTRL_EN_MASK);
-	val |= ((0x14 << USB3_GEN2_SET0_G2_TX_AMP_SHIFT)
-		| (1 << USB3_GEN2_SET0_G2_TX_AMP_ADJ_SHIFT)
-		| (0xA << USB3_GEN2_SET0_G2_TX_EMPH_AMP_SHIFT)
-		| (1 << USB3_GEN2_SET0_G2_TX_EMPH_EN_SHIFT));
-	mv_u3d_phy_write(base, USB3_GEN2_SET0, val);
-	udelay(100);
-
-	mv_u3d_phy_read(base, USB3_TX_EMPPH);
-	val &= ~(USB3_TX_EMPPH_AMP_MASK
-		| USB3_TX_EMPPH_EN_MASK
-		| USB3_TX_EMPPH_AMP_FORCE_MASK
-		| USB3_TX_EMPPH_PAR1_MASK
-		| USB3_TX_EMPPH_PAR2_MASK);
-	val |= ((0xB << USB3_TX_EMPPH_AMP_SHIFT)
-		| (1 << USB3_TX_EMPPH_EN_SHIFT)
-		| (1 << USB3_TX_EMPPH_AMP_FORCE_SHIFT)
-		| (0x1C << USB3_TX_EMPPH_PAR1_SHIFT)
-		| (1 << USB3_TX_EMPPH_PAR2_SHIFT));
-
-	mv_u3d_phy_write(base, USB3_TX_EMPPH, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_GEN2_SET1);
-	val &= ~(USB3_GEN2_SET1_G2_RX_SELMUPI_MASK
-		| USB3_GEN2_SET1_G2_RX_SELMUPF_MASK
-		| USB3_GEN2_SET1_G2_RX_SELMUFI_MASK
-		| USB3_GEN2_SET1_G2_RX_SELMUFF_MASK);
-	val |= ((1 << USB3_GEN2_SET1_G2_RX_SELMUPI_SHIFT)
-		| (1 << USB3_GEN2_SET1_G2_RX_SELMUPF_SHIFT)
-		| (1 << USB3_GEN2_SET1_G2_RX_SELMUFI_SHIFT)
-		| (1 << USB3_GEN2_SET1_G2_RX_SELMUFF_SHIFT));
-	mv_u3d_phy_write(base, USB3_GEN2_SET1, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_DIGITAL_LOOPBACK_EN);
-	val &= ~USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_MASK;
-	val |= 1 << USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_SHIFT;
-	mv_u3d_phy_write(base, USB3_DIGITAL_LOOPBACK_EN, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_IMPEDANCE_TX_SSC);
-	val &= ~USB3_IMPEDANCE_TX_SSC_SSC_AMP_MASK;
-	val |= 0xC << USB3_IMPEDANCE_TX_SSC_SSC_AMP_SHIFT;
-	mv_u3d_phy_write(base, USB3_IMPEDANCE_TX_SSC, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_IMPEDANCE_CALI_CTRL);
-	val &= ~USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_MASK;
-	val |= 0x4 << USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_SHIFT;
-	mv_u3d_phy_write(base, USB3_IMPEDANCE_CALI_CTRL, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_PHY_ISOLATION_MODE);
-	val &= ~(USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_MASK
-		| USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_MASK
-		| USB3_PHY_ISOLATION_MODE_TX_DRV_IDLE_MASK);
-	val |= ((1 << USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_SHIFT)
-		| (1 << USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_SHIFT));
-	mv_u3d_phy_write(base, USB3_PHY_ISOLATION_MODE, val);
-	udelay(100);
-
-	val = mv_u3d_phy_read(base, USB3_TXDETRX);
-	val &= ~(USB3_TXDETRX_VTHSEL_MASK);
-	val |= 0x1 << USB3_TXDETRX_VTHSEL_SHIFT;
-	mv_u3d_phy_write(base, USB3_TXDETRX, val);
-	udelay(100);
-
-	dev_dbg(mv_u3d_phy->dev, "start calibration\n");
-
-calstart:
-	/* Perform Manual Calibration */
-	mv_u3d_phy_set(base, USB3_KVCO_CALI_CONTROL,
-		1 << USB3_KVCO_CALI_CONTROL_CAL_START_SHIFT);
-
-	mdelay(1);
-
-	count = 0;
-	while (1) {
-		val = mv_u3d_phy_read(base, USB3_KVCO_CALI_CONTROL);
-		if (val & (1 << USB3_KVCO_CALI_CONTROL_CAL_DONE_SHIFT))
-			break;
-		else if (count > 50) {
-			dev_dbg(mv_u3d_phy->dev, "calibration failure, retry...\n");
-			goto calstart;
-		}
-		count++;
-		mdelay(1);
-	}
-
-	/* active PIPE interface */
-	mv_u3d_phy_write(base, USB3_PIPE_SM_CTRL,
-		1 << USB3_PIPE_SM_CTRL_PHY_INIT_DONE);
-
-	return 0;
-}
-
-static int mv_u3d_phy_probe(struct platform_device *pdev)
-{
-	struct mv_u3d_phy *mv_u3d_phy;
-	struct mv_usb_platform_data *pdata;
-	struct device *dev = &pdev->dev;
-	struct resource *res;
-	void __iomem	*phy_base;
-	int	ret;
-
-	pdata = dev_get_platdata(&pdev->dev);
-	if (!pdata) {
-		dev_err(&pdev->dev, "%s: no platform data defined\n", __func__);
-		return -EINVAL;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	phy_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(phy_base))
-		return PTR_ERR(phy_base);
-
-	mv_u3d_phy = devm_kzalloc(dev, sizeof(*mv_u3d_phy), GFP_KERNEL);
-	if (!mv_u3d_phy)
-		return -ENOMEM;
-
-	mv_u3d_phy->dev			= &pdev->dev;
-	mv_u3d_phy->plat		= pdata;
-	mv_u3d_phy->base		= phy_base;
-	mv_u3d_phy->phy.dev		= mv_u3d_phy->dev;
-	mv_u3d_phy->phy.label		= "mv-u3d-phy";
-	mv_u3d_phy->phy.init		= mv_u3d_phy_init;
-	mv_u3d_phy->phy.shutdown	= mv_u3d_phy_shutdown;
-
-	ret = usb_add_phy(&mv_u3d_phy->phy, USB_PHY_TYPE_USB3);
-	if (ret)
-		goto err;
-
-	if (!mv_u3d_phy->clk)
-		mv_u3d_phy->clk = clk_get(mv_u3d_phy->dev, "u3dphy");
-
-	platform_set_drvdata(pdev, mv_u3d_phy);
-
-	dev_info(&pdev->dev, "Initialized Marvell USB 3.0 PHY\n");
-err:
-	return ret;
-}
-
-static int mv_u3d_phy_remove(struct platform_device *pdev)
-{
-	struct mv_u3d_phy *mv_u3d_phy = platform_get_drvdata(pdev);
-
-	usb_remove_phy(&mv_u3d_phy->phy);
-
-	if (mv_u3d_phy->clk) {
-		clk_put(mv_u3d_phy->clk);
-		mv_u3d_phy->clk = NULL;
-	}
-
-	return 0;
-}
-
-static struct platform_driver mv_u3d_phy_driver = {
-	.probe		= mv_u3d_phy_probe,
-	.remove		= mv_u3d_phy_remove,
-	.driver		= {
-		.name	= "mv-u3d-phy",
-		.owner	= THIS_MODULE,
-	},
-};
-
-module_platform_driver(mv_u3d_phy_driver);
-MODULE_DESCRIPTION("Marvell USB 3.0 PHY controller");
-MODULE_AUTHOR("Yu Xu <yuxu@...vell.com>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:mv-u3d-phy");
diff --git a/drivers/usb/phy/phy-mv-u3d-usb.h b/drivers/usb/phy/phy-mv-u3d-usb.h
deleted file mode 100644
index 2a658cb9a527..000000000000
--- a/drivers/usb/phy/phy-mv-u3d-usb.h
+++ /dev/null
@@ -1,105 +0,0 @@
-/*
- * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- */
-
-#ifndef __MV_U3D_PHY_H
-#define __MV_U3D_PHY_H
-
-#define USB3_POWER_PLL_CONTROL		0x1
-#define USB3_KVCO_CALI_CONTROL		0x2
-#define USB3_IMPEDANCE_CALI_CTRL	0x3
-#define USB3_IMPEDANCE_TX_SSC		0x4
-#define USB3_SQUELCH_FFE		0x6
-#define USB3_GEN1_SET0			0xD
-#define USB3_GEN2_SET0			0xF
-#define USB3_GEN2_SET1			0x10
-#define USB3_DIGITAL_LOOPBACK_EN	0x23
-#define USB3_PHY_ISOLATION_MODE		0x26
-#define USB3_TXDETRX			0x48
-#define USB3_TX_EMPPH			0x5E
-#define USB3_RESET_CONTROL		0x90
-#define USB3_PIPE_SM_CTRL		0x91
-
-#define USB3_RESET_CONTROL_RESET_PIPE			0x1
-#define USB3_RESET_CONTROL_RESET_PHY			0x2
-
-#define USB3_POWER_PLL_CONTROL_REF_FREF_SEL_MASK	(0x1F << 0)
-#define USB3_POWER_PLL_CONTROL_REF_FREF_SEL_SHIFT	0
-#define USB3_PLL_25MHZ					0x2
-#define USB3_PLL_26MHZ					0x5
-#define USB3_POWER_PLL_CONTROL_PHY_MODE_MASK		(0x7 << 5)
-#define USB3_POWER_PLL_CONTROL_PHY_MODE_SHIFT		5
-#define USB3_POWER_PLL_CONTROL_PU_MASK			(0xF << 12)
-#define USB3_POWER_PLL_CONTROL_PU_SHIFT			12
-#define USB3_POWER_PLL_CONTROL_PU			(0xF << 12)
-
-#define USB3_KVCO_CALI_CONTROL_USE_MAX_PLL_RATE_MASK	(0x1 << 12)
-#define USB3_KVCO_CALI_CONTROL_USE_MAX_PLL_RATE_SHIFT	12
-#define USB3_KVCO_CALI_CONTROL_CAL_DONE_SHIFT		14
-#define USB3_KVCO_CALI_CONTROL_CAL_START_SHIFT		15
-
-#define USB3_SQUELCH_FFE_FFE_CAP_SEL_MASK		0xF
-#define USB3_SQUELCH_FFE_FFE_CAP_SEL_SHIFT		0
-#define USB3_SQUELCH_FFE_FFE_RES_SEL_MASK		(0x7 << 4)
-#define USB3_SQUELCH_FFE_FFE_RES_SEL_SHIFT		4
-#define USB3_SQUELCH_FFE_SQ_THRESH_IN_MASK		(0x1F << 8)
-#define USB3_SQUELCH_FFE_SQ_THRESH_IN_SHIFT		8
-
-#define USB3_GEN1_SET0_G1_TX_SLEW_CTRL_EN_MASK		(0x1 << 15)
-#define USB3_GEN1_SET0_G1_TX_EMPH_EN_SHIFT		11
-
-#define USB3_GEN2_SET0_G2_TX_AMP_MASK			(0x1F << 1)
-#define USB3_GEN2_SET0_G2_TX_AMP_SHIFT			1
-#define USB3_GEN2_SET0_G2_TX_AMP_ADJ_SHIFT		6
-#define USB3_GEN2_SET0_G2_TX_EMPH_AMP_MASK		(0xF << 7)
-#define USB3_GEN2_SET0_G2_TX_EMPH_AMP_SHIFT		7
-#define USB3_GEN2_SET0_G2_TX_EMPH_EN_MASK		(0x1 << 11)
-#define USB3_GEN2_SET0_G2_TX_EMPH_EN_SHIFT		11
-#define USB3_GEN2_SET0_G2_TX_SLEW_CTRL_EN_MASK		(0x1 << 15)
-#define USB3_GEN2_SET0_G2_TX_SLEW_CTRL_EN_SHIFT		15
-
-#define USB3_GEN2_SET1_G2_RX_SELMUPI_MASK		(0x7 << 0)
-#define USB3_GEN2_SET1_G2_RX_SELMUPI_SHIFT		0
-#define USB3_GEN2_SET1_G2_RX_SELMUPF_MASK		(0x7 << 3)
-#define USB3_GEN2_SET1_G2_RX_SELMUPF_SHIFT		3
-#define USB3_GEN2_SET1_G2_RX_SELMUFI_MASK		(0x3 << 6)
-#define USB3_GEN2_SET1_G2_RX_SELMUFI_SHIFT		6
-#define USB3_GEN2_SET1_G2_RX_SELMUFF_MASK		(0x3 << 8)
-#define USB3_GEN2_SET1_G2_RX_SELMUFF_SHIFT		8
-
-#define USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_MASK		(0x3 << 10)
-#define USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_SHIFT		10
-
-#define USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_MASK	(0x7 << 12)
-#define USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_SHIFT	12
-
-#define USB3_IMPEDANCE_TX_SSC_SSC_AMP_MASK		(0x3F << 0)
-#define USB3_IMPEDANCE_TX_SSC_SSC_AMP_SHIFT		0
-
-#define USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_MASK		0xF
-#define USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_SHIFT	0
-#define USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_MASK		(0xF << 4)
-#define USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_SHIFT	4
-#define USB3_PHY_ISOLATION_MODE_TX_DRV_IDLE_MASK	(0x1 << 8)
-
-#define USB3_TXDETRX_VTHSEL_MASK			(0x3 << 4)
-#define USB3_TXDETRX_VTHSEL_SHIFT			4
-
-#define USB3_TX_EMPPH_AMP_MASK				(0xF << 0)
-#define USB3_TX_EMPPH_AMP_SHIFT				0
-#define USB3_TX_EMPPH_EN_MASK				(0x1 << 6)
-#define USB3_TX_EMPPH_EN_SHIFT				6
-#define USB3_TX_EMPPH_AMP_FORCE_MASK			(0x1 << 7)
-#define USB3_TX_EMPPH_AMP_FORCE_SHIFT			7
-#define USB3_TX_EMPPH_PAR1_MASK				(0x1F << 8)
-#define USB3_TX_EMPPH_PAR1_SHIFT			8
-#define USB3_TX_EMPPH_PAR2_MASK				(0x1 << 13)
-#define USB3_TX_EMPPH_PAR2_SHIFT			13
-
-#define USB3_PIPE_SM_CTRL_PHY_INIT_DONE			15
-
-#endif /* __MV_U3D_PHY_H */
-- 
1.9.0

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists