| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1398201675-17379-2-git-send-email-santosh.shilimkar@ti.com>
Date: Tue, 22 Apr 2014 17:21:14 -0400
From: Santosh Shilimkar <santosh.shilimkar@...com>
To: <netdev@...r.kernel.org>
CC: <linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, Sandeep Nair <sandeep_n@...com>,
Rob Herring <robh+dt@...nel.org>,
Grant Likely <grant.likely@...aro.org>,
Pawel Moll <pawel.moll@....com>,
Mark Rutland <mark.rutland@....com>,
Ian Campbell <ijc+devicetree@...lion.org.uk>,
Kumar Gala <galak@...eaurora.org>,
David Miller <davem@...emloft.net>,
Santosh Shilimkar <santosh.shilimkar@...com>
Subject: [PATCH 1/2] Documentation: dt: net: Add binding doc for Keystone NetCP ethernet driver
From: Sandeep Nair <sandeep_n@...com>
The network coprocessor (NetCP) is a hardware accelerator that processes
Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet
switch sub-module to send and receive packets. NetCP also includes a packet
accelerator (PA) module to perform packet classification operations such as
header matching, and packet modification operations such as checksum
generation. NetCP can also optionally include a Security Accelerator(SA)
capable of performing IPSec operations on ingress/egress packets.
Keystone SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
includes a 3-port Ethernet switch sub-module capable of 10Gb/s and
1Gb/s rates per Ethernet port.
NetCP Subsystem device tree layout looks something like below:
-----------------------------
NetCP subsystem(10G or 1G)
-----------------------------
|
|-> NetCP Devices -> |
| |-> GBE/XGBE Switch
| |
| |-> Packet Accelerator
| |
| |-> Security Accelerator
|
|
|
|-> NetCP Interfaces -> |
|-> Ethernet Port 0
|
|-> Ethernet Port 1
|
|-> Ethernet Port 2
|
|-> Ethernet Port 3
Common driver supports GBE as well XGBE network processors.
Cc: Rob Herring <robh+dt@...nel.org>
Cc: Grant Likely <grant.likely@...aro.org>
Cc: Pawel Moll <pawel.moll@....com>
Cc: Mark Rutland <mark.rutland@....com>
Cc: Ian Campbell <ijc+devicetree@...lion.org.uk>
Cc: Kumar Gala <galak@...eaurora.org>
Cc: David Miller <davem@...emloft.net>
Signed-off-by: Sandeep Nair <sandeep_n@...com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@...com>
---
.../devicetree/bindings/net/keystone-netcp.txt | 197 ++++++++++++++++++++
1 file changed, 197 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/keystone-netcp.txt
diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt
new file mode 100644
index 0000000..a7d061b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt
@@ -0,0 +1,197 @@
+This document describes the device tree bindings associated with the
+keystone network coprocessor(NetCP) driver support.
+
+The network coprocessor (NetCP) is a hardware accelerator that processes
+Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsytem with a ethernet
+switch sub-module to send and receive packets. NetCP also includes a packet
+accelerator (PA) module to perform packet classification operations such as
+header matching, and packet modification operations such as checksum
+generation. NetCP can also optionally include a Security Accelerator (SA)
+capable of performing IPSec operations on ingress/egress packets.
+
+Keystone II SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
+includes a 3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates
+per Ethernet port.
+
+Keystone NetCP driver has a plug-in module architecture where each of the NetCP
+sub-modules exist as a loadable kernel module which plug in to the netcp core.
+These sub-modules are represented as "netcp-devices" in the dts bindings. It is
+mandatory to have the ethernet switch sub-module for the ethernet interface to
+be operational. Any other sub-module like the PA is optional.
+
+NetCP Ethernet SubSystem Layout:
+
+-----------------------------
+ NetCP subsystem(10G or 1G)
+-----------------------------
+ |
+ |-> NetCP Devices -> |
+ | |-> GBE/XGBE Switch
+ | |
+ | |-> Packet Accelerator
+ | |
+ | |-> Security Accelerator
+ |
+ |
+ |
+ |-> NetCP Interfaces -> |
+ |-> Ethernet Port 0
+ |
+ |-> Ethernet Port 1
+ |
+ |-> Ethernet Port 2
+ |
+ |-> Ethernet Port 3
+
+
+NetCP subsystem properties:
+Required properties:
+- compatible: Should be "ti,netcp-1.0"
+- clocks: phandle to the reference clocks for the subsystem.
+- dma-id: Navigator packet dma instance id.
+
+Optional properties:
+- reg: register location and the size for the following register
+ regions in the specified order.
+ - Efuse MAC address register
+- dma-coherent: Present if dma operations are coherent
+- big-endian: Keystone devices can be operated in a mode where the DSP is in
+ the big endian mode. In such cases enable this option. This
+ option should also be enabled if the ARM is operated in
+ big endian mode with the DSP in little endian.
+
+NetCP device properties: Device specification for NetCP sub-modules.
+1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications.
+Required properties:
+- label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb.
+- reg: register location and the size for the following register
+ regions in the specified order.
+ - subsystem registers
+ - serdes registers
+- tx-channel: the navigator packet dma channel number for tx.
+- tx-queue: the navigator queue number associated with the tx dma channel.
+- interfaces: specification for each of the switch port to be registered as a
+ network interface in the stack.
+-- slave-port: Switch port number, 0 based numbering.
+-- link-interface: type of link interface, supported options are
+ - mac<->mac auto negotiate mode: 0
+ - mac<->phy mode: 1
+ - mac<->mac forced mode: 2
+ - mac<->fiber mode: 3
+ - mac<->phy mode with no mdio: 4
+ - 10Gb mac<->phy mode : 10
+ - 10Gb mac<->mac forced mode : 11
+----phy-handle: phandle to PHY device
+
+Optional properties:
+- enable-ale: NetCP driver keeps the address learning feature in the ethernet
+ switch module disabled. This attribute is to enable the address
+ learning.
+- secondary-slave-ports: specification for each of the switch port not be
+ registered as a network interface. NetCP driver
+ will only initialize these ports and attach PHY
+ driver to them if needed.
+
+NetCP interface properties: Interface specification for NetCP sub-modules.
+Required properties:
+- rx-channel: the navigator packet dma channel number for rx.
+- rx-queue: the navigator queue number associated with rx dma channel.
+- rx-pool: specifies the number of descriptors to be used & the region-id
+ for creating the rx descriptor pool.
+- tx-pool: specifies the number of descriptors to be used & the region-id
+ for creating the tx descriptor pool.
+- rx-queue-depth: number of descriptors in each of the free descriptor
+ queue (FDQ) for the pktdma Rx flow. There can be at
+ present a maximum of 4 queues per Rx flow.
+- rx-buffer-size: the buffer size for each of the Rx flow FDQ.
+- tx-completion-queue: the navigator queue number where the descriptors are
+ recycled after Tx DMA completion.
+
+Optional properties:
+- efuse-mac: If this is 1, then the MAC address for the interface is
+ obtained from the device efuse mac address register
+- local-mac-address: the driver is designed to use the of_get_mac_address api
+ only if efuse-mac is 0. When efuse-mac is 0, the MAC
+ address is obtained from local-mac-address. If this
+ attribute is not present, then the driver will use a
+ random MAC address.
+- "netcp-device label": phandle to the device specification for each of NetCP
+ sub-module attached to this interface.
+
+Example binding:
+
+netcp: netcp@...0000 {
+ reg = <0x2620110 0x8>;
+ reg-names = "efuse";
+ compatible = "ti,netcp-1.0";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
+ dma-coherent;
+ /* big-endian; */
+ dma-id = <0>;
+
+ netcp-devices {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ gbe@...090000 {
+ label = "netcp-gbe";
+ reg = <0x2090000 0xf00>;
+ /* enable-ale; */
+ tx-queue = <648>;
+ tx-channel = <8>;
+
+ interfaces {
+ gbe0: interface-0 {
+ slave-port = <0>;
+ link-interface = <4>;
+ };
+ gbe1: interface-1 {
+ slave-port = <1>;
+ link-interface = <4>;
+ };
+ };
+
+ secondary-slave-ports {
+ port-2 {
+ slave-port = <2>;
+ link-interface = <2>;
+ };
+ port-3 {
+ slave-port = <3>;
+ link-interface = <2>;
+ };
+ };
+ };
+ };
+
+ netcp-interfaces {
+ interface-0 {
+ rx-channel = <22>;
+ rx-pool = <1024 12>;
+ tx-pool = <1024 12>;
+ rx-queue-depth = <128 128 0 0>;
+ rx-buffer-size = <1518 4096 0 0>;
+ rx-queue = <8704>;
+ tx-completion-queue = <8706>;
+ efuse-mac = <1>;
+ netcp-gbe = <&gbe0>;
+
+ };
+ interface-1 {
+ rx-channel = <23>;
+ rx-pool = <1024 12>;
+ tx-pool = <1024 12>;
+ rx-queue-depth = <128 128 0 0>;
+ rx-buffer-size = <1518 4096 0 0>;
+ rx-queue = <8705>;
+ tx-completion-queue = <8707>;
+ efuse-mac = <0>;
+ local-mac-address = [02 18 31 7e 3e 6f];
+ netcp-gbe = <&gbe1>;
+ };
+ };
+};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists