| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1398354495-20782-20-git-send-email-iivanov@mm-sol.com>
Date: Thu, 24 Apr 2014 18:48:14 +0300
From: "Ivan T. Ivanov" <iivanov@...sol.com>
To: Rob Herring <robh+dt@...nel.org>, Pawel Moll <pawel.moll@....com>,
Mark Rutland <mark.rutland@....com>,
Ian Campbell <ijc+devicetree@...lion.org.uk>,
Kumar Gala <galak@...eaurora.org>,
Randy Dunlap <rdunlap@...radead.org>,
Felipe Balbi <balbi@...com>,
Grant Likely <grant.likely@...aro.org>
Cc: "Ivan T. Ivanov" <iivanov@...sol.com>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
David Brown <davidb@...eaurora.org>,
devicetree@...r.kernel.org, linux-doc@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-usb@...r.kernel.org,
linux-arm-msm@...r.kernel.org, Mayank Rana <mrana@...eaurora.org>
Subject: [PATCH v7 19/20] usb: phy: msm: Vote for corner of VDD CX instead of voltage of VDD CX
From: "Ivan T. Ivanov" <iivanov@...sol.com>
New platform uses RBCPR hardware feature, with that voting for
absolute voltage of VDD CX is not required. Hence vote for corner of
VDD CX which uses nominal corner voltage on VDD CX.
Signed-off-by: Ivan T. Ivanov <iivanov@...sol.com>
Cc: Mayank Rana <mrana@...eaurora.org>
---
.../devicetree/bindings/usb/msm-hsusb.txt | 5 ++++
drivers/usb/phy/phy-msm-usb.c | 35 +++++++++++++++++-----
include/linux/usb/msm_hsusb.h | 1 +
3 files changed, 33 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
index 0669667..2826f2a 100644
--- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt
+++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
@@ -65,6 +65,10 @@ Optional properties:
Some platforms may have configuration to allow USB
controller work with any of the two HSPHYs present.
+- qcom,vdd-levels: This property must be a list of three integer values
+ (no, min, max) where each value represents either a voltage
+ in microvolts or a value corresponding to voltage corner.
+
Example HSUSB OTG controller device node:
usb@...55000 {
@@ -87,4 +91,5 @@ Example HSUSB OTG controller device node:
qcom,otg-control = <1>;
qcom,phy-init-sequence = < -1 0x63 >;
+ qcom,vdd-levels = <1 5 7>;
};
diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c
index 602e6c8..9240f5b 100644
--- a/drivers/usb/phy/phy-msm-usb.c
+++ b/drivers/usb/phy/phy-msm-usb.c
@@ -62,6 +62,13 @@
#define USB_PHY_VDD_DIG_VOL_MIN 1000000 /* uV */
#define USB_PHY_VDD_DIG_VOL_MAX 1320000 /* uV */
+#define USB_PHY_SUSP_DIG_VOL 500000 /* uV */
+
+enum vdd_levels {
+ VDD_LEVEL_NONE = 0,
+ VDD_LEVEL_MIN,
+ VDD_LEVEL_MAX,
+};
static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)
{
@@ -69,8 +76,8 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)
if (init) {
ret = regulator_set_voltage(motg->vddcx,
- USB_PHY_VDD_DIG_VOL_MIN,
- USB_PHY_VDD_DIG_VOL_MAX);
+ motg->vdd_levels[VDD_LEVEL_MIN],
+ motg->vdd_levels[VDD_LEVEL_MAX]);
if (ret) {
dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
return ret;
@@ -81,7 +88,7 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)
dev_err(motg->phy.dev, "unable to enable hsusb vddcx\n");
} else {
ret = regulator_set_voltage(motg->vddcx, 0,
- USB_PHY_VDD_DIG_VOL_MAX);
+ motg->vdd_levels[VDD_LEVEL_MAX]);
if (ret)
dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
ret = regulator_disable(motg->vddcx);
@@ -435,17 +442,16 @@ static int msm_phy_init(struct usb_phy *phy)
#ifdef CONFIG_PM
-#define USB_PHY_SUSP_DIG_VOL 500000
static int msm_hsusb_config_vddcx(struct msm_otg *motg, int high)
{
- int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
+ int max_vol = motg->vdd_levels[VDD_LEVEL_MAX];
int min_vol;
int ret;
if (high)
- min_vol = USB_PHY_VDD_DIG_VOL_MIN;
+ min_vol = motg->vdd_levels[VDD_LEVEL_MIN];
else
- min_vol = USB_PHY_SUSP_DIG_VOL;
+ min_vol = motg->vdd_levels[VDD_LEVEL_NONE];
ret = regulator_set_voltage(motg->vddcx, min_vol, max_vol);
if (ret) {
@@ -1441,7 +1447,7 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
struct device_node *node = pdev->dev.of_node;
struct property *prop;
int len, ret, words;
- u32 val;
+ u32 val, tmp[3];
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
@@ -1472,6 +1478,19 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
if (!of_property_read_u32(node, "qcom,phy-num", &val) && val < 2)
motg->phy_number = val;
+ motg->vdd_levels[VDD_LEVEL_NONE] = USB_PHY_SUSP_DIG_VOL;
+ motg->vdd_levels[VDD_LEVEL_MIN] = USB_PHY_VDD_DIG_VOL_MIN;
+ motg->vdd_levels[VDD_LEVEL_MAX] = USB_PHY_VDD_DIG_VOL_MAX;
+
+ if (of_get_property(node, "qcom,vdd-levels", &len) &&
+ len == sizeof(tmp)) {
+ of_property_read_u32_array(node, "qcom,vdd-levels",
+ tmp, len / sizeof(*tmp));
+ motg->vdd_levels[VDD_LEVEL_NONE] = tmp[VDD_LEVEL_NONE];
+ motg->vdd_levels[VDD_LEVEL_MIN] = tmp[VDD_LEVEL_MIN];
+ motg->vdd_levels[VDD_LEVEL_MAX] = tmp[VDD_LEVEL_MAX];
+ }
+
prop = of_find_property(node, "qcom,phy-init-sequence", &len);
if (!prop || !len)
return 0;
diff --git a/include/linux/usb/msm_hsusb.h b/include/linux/usb/msm_hsusb.h
index 4628f1a..b0a3924 100644
--- a/include/linux/usb/msm_hsusb.h
+++ b/include/linux/usb/msm_hsusb.h
@@ -169,6 +169,7 @@ struct msm_otg {
struct reset_control *phy_rst;
struct reset_control *link_rst;
+ int vdd_levels[3];
};
#endif
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists