| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20140618150152.GP8860@dragon>
Date: Wed, 18 Jun 2014 23:01:53 +0800
From: Shawn Guo <shawn.guo@...escale.com>
To: Lothar Waßmann <LW@...O-electronics.de>
CC: Ian Campbell <ijc+devicetree@...lion.org.uk>,
Kumar Gala <galak@...eaurora.org>,
Mark Rutland <mark.rutland@....com>,
Pawel Moll <pawel.moll@....com>,
Rob Herring <robh+dt@...nel.org>,
Russell King <linux@....linux.org.uk>,
Sascha Hauer <kernel@...gutronix.de>,
<devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH] ARM: dts: add support for Ka-Ro TX51
On Thu, Jun 12, 2014 at 03:09:44PM +0200, Lothar Waßmann wrote:
> Add support for Ka-Ro electronics i.MX51 based TX51 modules
>
> Signed-off-by: Lothar Waßmann <LW@...O-electronics.de>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx51-tx51.dts | 620 ++++++++++++++++++++++++++++++++++++++
> 2 files changed, 621 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx51-tx51.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 0f1e8be..8dd4dbc 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -177,6 +177,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
> imx51-babbage.dtb \
> imx51-digi-connectcore-jsk.dtb \
> imx51-eukrea-mbimxsd51-baseboard.dtb \
> + imx51-tx51.dtb \
> imx53-ard.dtb \
> imx53-m53evk.dtb \
> imx53-mba53.dtb \
> diff --git a/arch/arm/boot/dts/imx51-tx51.dts b/arch/arm/boot/dts/imx51-tx51.dts
> new file mode 100644
> index 0000000..9ae7758
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx51-tx51.dts
> @@ -0,0 +1,620 @@
> +/*
> + * Copyright 2012-2014 Lothar Waßmann <LW@...O-electronics.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx51.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
imx51.dtsi already includes them.
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + model = "Ka-Ro electronics TX51 module";
> + compatible = "karo,tx51", "fsl,imx51";
> +
> + aliases {
> + backlight = &backlight;
> + display = &display;
> + i2c1 = &i2c_gpio;
> + usbotg = &usbotg;
> + };
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + backlight: pwm-backlight {
> + compatible = "pwm-backlight";
> +
Drop this new line.
> + pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
> + power-supply = <®_3v3>;
> + brightness-levels = <
> + 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100
> + >;
> + default-brightness-level = <50>;
> + };
> +
> + clocks {
> + ckih1 {
> + clock-frequency = <0>;
> + };
> +
> + mclk: clock@0 {
> + compatible = "fixed-clock";
> + reg = <0>;
> + #clock-cells = <0>;
> + clock-frequency = <27000000>;
> + };
> +
> + clk_26M: clock@1 {
When using generic name, you will need clock-output-names property.
Otherwise, the clocks will fail in registration except the first one,
because of clock name collision.
> + compatible = "fixed-clock";
> + reg = <1>;
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + interface-pix-fmt = "rgb24";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu_disp0>;
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +
> + i2c_gpio: i2c-gpio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "i2c-gpio";
> + gpios = <&gpio4 17 0
> + &gpio4 16 0>;
> + clock-frequency = <400000>;
> +
> + rtc1: ds1339@68 {
> + compatible = "dallas,ds1339";
> + reg = <0x68>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_stk5led>;
> +
> + user {
> + label = "Heartbeat";
> + gpios = <&gpio4 10 0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_2v5: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + reg_3v3: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_etn_phy: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "ETN PHY Power";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_lcd_pwr: regulator@5 {
> + compatible = "regulator-fixed";
> + reg = <5>;
> + regulator-name = "LCD POWER";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_lcd_reset: regulator@6 {
> + compatible = "regulator-fixed";
> + reg = <6>;
> + regulator-name = "LCD RESET";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd_reset>;
> + gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> +
> + sound {
> + compatible = "karo,tx51-audio-sgtl5000", "fsl,imx-sgtl5000";
> + model = "tx53-audio-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&sgtl5000>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + /* '1' based port numbers according to datasheet names */
> + mux-int-port = <1>;
> + mux-ext-port = <3>;
> + sysclk = <26000000>;
> + };
> +
> + usbphy {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "simple-bus";
> +
> + usbh1phy: usbh1phy@0 {
The node name should be something generic like usbphy?
> + compatible = "usb-nop-xceiv";
> + reg = <0>;
> + clocks = <&clk_26M>;
> + clock-names = "main_clk";
> + };
> + };
> +};
> +
> +&audmux {
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-mode = "mii";
> +// phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
Drop it?
> + phy-handle = <&phy0>;
> + mac-address = [000000000000]; /* will be set by U-Boot */
Shouldn't it be local-mac-address?
> + status = "okay";
> +
> + phy0: ethernet-phy@0 {
> + interrupt-parent = <&gpio3>;
> + interrupts = <18 0>;
> + device_type = "ethernet-phy";
> + };
> +};
> +
> +&ipu {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + sgtl5000: sgtl5000@0a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&mclk>;
> + VDDA-supply = <®_2v5>;
> + VDDIO-supply = <®_3v3>;
> + };
> +
> + polytouch: edt-ft5x06@38 {
> + compatible = "edt,edt-ft5x06";
> + reg = <0x38>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_edt_ft5x06>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <5 0>;
> + reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> + };
> +
> + touchscreen: tsc2007@48 {
> + compatible = "ti,tsc2007";
> + reg = <0x48>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tsc2007>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <3 0>;
> + gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
> + ti,x-plate-ohms = <660>;
> + linux,wakeup;
> + };
> +};
> +
> +&iomuxc {
> + imx51-tx51 {
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX51_PAD_GPIO1_7__GPIO1_7 0x20e0 /* 26MHz osc enable */
> + >;
> + };
> +
> + pinctrl_edt_ft5x06: edt-ft5x056grp {
> + fsl,pins = <
> + MX51_PAD_GPIO1_5__GPIO1_5 0x20e0 /* Interrupt */
> + MX51_PAD_CSI2_PIXCLK__GPIO4_15 0x20e0 /* Reset */
> + MX51_PAD_CSI2_D12__GPIO4_9 0x20e0 /* Wake */
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX51_PAD_EIM_A20__GPIO2_14 0x20e4 /* PHY reset */
> + MX51_PAD_GPIO1_3__GPIO1_3 0x20e4 /* PHY power */
> + MX51_PAD_NANDF_CS3__FEC_MDC 0x2004
> + MX51_PAD_EIM_EB2__FEC_MDIO 0x0005
> + MX51_PAD_NANDF_RB3__FEC_RX_CLK 0x2000
> + MX51_PAD_NANDF_D11__FEC_RX_DV 0x2000
> + MX51_PAD_NANDF_D9__FEC_RDATA0 0x2000
> + MX51_PAD_EIM_EB3__FEC_RDATA1 0x0001
> + MX51_PAD_EIM_CS2__FEC_RDATA2 0x0001
> + MX51_PAD_EIM_CS3__FEC_RDATA3 0x0001
> + MX51_PAD_EIM_CS4__FEC_RX_ER 0x0001
> + MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK 0x2000
> + MX51_PAD_NANDF_CS7__FEC_TX_EN 0x2004
> + MX51_PAD_NANDF_D8__FEC_TDATA0 0x2004
> + MX51_PAD_NANDF_CS4__FEC_TDATA1 0x2004
> + MX51_PAD_NANDF_CS5__FEC_TDATA2 0x2004
> + MX51_PAD_NANDF_CS6__FEC_TDATA3 0x2004
> + MX51_PAD_NANDF_RB2__FEC_COL 0x2000
> + MX51_PAD_EIM_CS5__FEC_CRS 0x0005
> + MX51_PAD_NANDF_CS2__GPIO3_18 0x20e4
> + >;
> + };
> +
> + pinctrl_fec_gpio: fec-gpiogrp {
> + fsl,pins = <
> + MX51_PAD_EIM_A20__GPIO2_14 0x20e4 /* PHY reset */
> + MX51_PAD_GPIO1_3__GPIO1_3 0x20e4 /* PHY power */
> + MX51_PAD_NANDF_RB3__GPIO3_11 0x20e4 /* RX_CLK/REGOFF */
> + MX51_PAD_NANDF_D9__GPIO3_31 0x20e4 /* RXD0/Mode0 */
> + MX51_PAD_EIM_EB3__GPIO2_23 0x20e4 /* RXD1/Mode1 */
> + MX51_PAD_EIM_CS2__GPIO2_27 0x20e4 /* RXD2/Mode2 */
> + MX51_PAD_EIM_CS3__GPIO2_28 0x20e4 /* RXD3/nINTSEL */
> + MX51_PAD_NANDF_RB2__GPIO3_10 0x20e4 /* COL/RMII/CRSDV */
> + MX51_PAD_EIM_CS5__GPIO2_30 0x20e4 /* CRS/PHYAD4 */
> + >;
> + };
> +
> + pinctrl_ipu_disp0: ipu-disp0grp {
> + fsl,pins = <
> + >;
> + };
> +
> + pinctrl_kpp_2: kppgrp-2 {
> + fsl,pins = <
> + MX51_PAD_KEY_ROW0__KEY_ROW0 0xe0
> + MX51_PAD_KEY_ROW1__KEY_ROW1 0xe0
> + MX51_PAD_KEY_ROW2__KEY_ROW2 0xe0
> + MX51_PAD_KEY_ROW3__KEY_ROW3 0xe0
> + MX51_PAD_KEY_COL0__KEY_COL0 0xe8
> + MX51_PAD_KEY_COL1__KEY_COL1 0xe8
> + MX51_PAD_KEY_COL2__KEY_COL2 0xe8
> + MX51_PAD_KEY_COL3__KEY_COL3 0xe8
> + MX51_PAD_KEY_COL4__KEY_COL4 0xe8
> + MX51_PAD_KEY_COL5__KEY_COL5 0xe8
> + >;
> + };
> +
> + pinctrl_lcd_pwr: lcd-pwrgrp {
> + fsl,pins = <
> + MX51_PAD_CSI2_HSYNC__GPIO4_14 0x04
> + >;
> + };
> +
> + pinctrl_lcd_reset: lcd-resetgrp {
> + fsl,pins = <
> + MX51_PAD_CSI2_VSYNC__GPIO4_13 0x04
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX51_PAD_GPIO1_2__PWM1_PWMO 0x0f4
> + >;
> + };
> +
> + pinctrl_stk5led: stk5ledgrp {
> + fsl,pins = <
> + MX51_PAD_CSI2_D13__GPIO4_10 0x20e4
> + >;
> + };
> +
> + pinctrl_tsc2007: tsc2007grp {
> + fsl,pins = <
> + MX51_PAD_DI1_D0_CS__GPIO3_3 0xc0 /* Interrupt */
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX51_PAD_UART1_RXD__UART1_RXD 0x1c1
> + MX51_PAD_UART1_TXD__UART1_TXD 0x1c5
> + MX51_PAD_UART1_RTS__UART1_RTS 0x1c1
> + MX51_PAD_UART1_CTS__UART1_CTS 0x1c5
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX51_PAD_UART2_RXD__UART2_RXD 0x1c1
> + MX51_PAD_UART2_TXD__UART2_TXD 0x1c5
> + MX51_PAD_EIM_D26__UART2_RTS 0x1c1
> + MX51_PAD_EIM_D25__UART2_CTS 0x1c5
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX51_PAD_UART3_RXD__UART3_RXD 0x1c1
> + MX51_PAD_UART3_TXD__UART3_TXD 0x1c5
> + MX51_PAD_EIM_D18__UART3_RTS 0x1c1
> + MX51_PAD_EIM_D17__UART3_CTS 0x1c5
> + >;
> + };
> + };
> +};
> +
> +&ipu_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +&kpp {
> + status = "okay";
Put 'status' at the bottom of property list.
> +
> + linux,keymap = < /* sample keymap */
> + MATRIX_KEY(0, 0, KEY_POWER)
> + MATRIX_KEY(0, 1, KEY_KP0)
> + MATRIX_KEY(0, 2, KEY_KP1)
> + MATRIX_KEY(0, 3, KEY_KP2)
> + MATRIX_KEY(1, 0, KEY_KP3)
> + MATRIX_KEY(1, 1, KEY_KP4)
> + MATRIX_KEY(1, 2, KEY_KP5)
> + MATRIX_KEY(1, 3, KEY_KP6)
> + MATRIX_KEY(2, 0, KEY_KP7)
> + MATRIX_KEY(2, 1, KEY_KP8)
> + MATRIX_KEY(2, 2, KEY_KP9)
> + >;
> +};
> +
> +&esdhc1 {
> + cd-gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
> + fsl,wp-controller;
Does it work for you, since the driver does not support it as of today?
> + status = "okay";
> +};
> +
> +&esdhc2 {
> + cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> +};
> +
> +&ecspi1 {
> + fsl,spi-num-chipselects = <2>;
> + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW &gpio4 25 GPIO_ACTIVE_LOW>;
More readable to write it like below?
cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
<&gpio4 25 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + spidev0: spi@0 {
> + compatible = "spidev";
> + reg = <0>;
> + spi-max-frequency = <54000000>;
> + };
> +
> + spidev1: spi@1 {
> + compatible = "spidev";
> + reg = <1>;
> + spi-max-frequency = <54000000>;
> + };
I'm not sure we should have these two devices.
> +};
> +
> +&ssi1 {
> + fsl,mode = "i2s-slave";
> + codec-handle = <&sgtl5000>;
> + status = "okay";
> +};
> +
> +&ssi2 {
> + status = "disabled";
> +};
Why is this needed, since the device is disabled in imx51.dtsi?
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + phy_type = "ulpi";
> + fsl,usbphy = <&usbh1phy>;
> + ignore-overcurrent;
> + enable-wakeup;
> + status = "okay";
> +};
> +
> +&usbotg {
> + ignore-overcurrent;
> + enable-wakeup;
> + phy_type = "utmi_wide";
> + status = "okay";
> +};
> +
> +&nfc {
Please sort the nodes alphabetically.
Shawn
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + nand-on-flash-bbt;
> + status = "okay";
> +};
> --
> 1.7.10.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists