| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5401A39C.4070504@kernel.org>
Date: Sat, 30 Aug 2014 11:12:44 +0100
From: Jonathan Cameron <jic23@...nel.org>
To: Laurentiu Palcu <laurentiu.palcu@...el.com>,
Grant Likely <grant.likely@...aro.org>,
Rob Herring <robh+dt@...nel.org>
CC: Hartmut Knaack <knaack.h@....de>,
Lars-Peter Clausen <lars@...afoo.de>,
Peter Meerwald <pmeerw@...erw.net>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Derek Basehore <dbasehore@...omium.org>,
Teodora Baluta <teodora.baluta@...el.com>,
Sachin Kamat <sachin.kamat@...aro.org>,
Jingoo Han <jg1.han@...sung.com>, linux-iio@...r.kernel.org,
devel@...verdev.osuosl.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org
Subject: Re: [PATCH 2/3] staging: iio: light: isl29018: add support for isl29023
and isl29035
On 29/08/14 15:26, Laurentiu Palcu wrote:
> Intersil chips ISL29018, ISL29023 and ISL29035 are very similar. They're
> all ambience light sensors. The ISL29018, however, is also a proximity
> sensor. The registers are similar too:
>
> -------------+----------+----------
> AVAILABLE IN | ADDR REG | NAME
> 290xx | |
> -------------+----------+----------
> 18/23/35| 00h| COMMANDI
> 18/23/35| 01h| COMMANDII (B4-7 are used only in 29018 for proximity)
> 18/23/35| 02h| DATALSB
> 18/23/35| 03h| DATAMSB
> 18/23/35| 04h| INT_LT_LSB
> 18/23/35| 05h| INT_LT_MSB
> 18/23/35| 06h| INT_HT_LSB
> 18/23/35| 07h| INT_HT_MSB
> 18/23| 08h| TEST
> 35| 0Fh| ID
> -------------+----------+-----------
>
> So, this patch will add support for ISL29023 and ISL29035 to the
> existing isl29018 driver. Since these 2 chips don't have proximity
> detection, the proximity sysfs attribute is not needed.
>
> Also, for ISL29035, since it has an ID register, make use of it in order
> to properly detect the chip and clear the brownout bit.
>
> Signed-off-by: Laurentiu Palcu <laurentiu.palcu@...el.com>
Hmm. Your changes look good. This driver still has quite a lot of non
standard ABI, but fair enough that you haven't dealt with that in this
patch.
Don't suppose you are interested in cleaning this up and getting the
driver out of staging?
Applied to the togreg branch of iio.git
Thanks,
Jonathan
> ---
> drivers/staging/iio/light/isl29018.c | 163 ++++++++++++++++++++++++++++++-----
> 1 file changed, 141 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/staging/iio/light/isl29018.c b/drivers/staging/iio/light/isl29018.c
> index 63c70be..b50f126 100644
> --- a/drivers/staging/iio/light/isl29018.c
> +++ b/drivers/staging/iio/light/isl29018.c
> @@ -1,5 +1,5 @@
> /*
> - * A iio driver for the light sensor ISL 29018.
> + * A iio driver for the light sensor ISL 29018/29023/29035.
> *
> * IIO driver for monitoring ambient light intensity in luxi, proximity
> * sensing and infrared sensing.
> @@ -58,10 +58,18 @@
> #define ISL29018_TEST_SHIFT 0
> #define ISL29018_TEST_MASK (0xFF << ISL29018_TEST_SHIFT)
>
> +#define ISL29035_REG_DEVICE_ID 0x0F
> +#define ISL29035_DEVICE_ID_SHIFT 0x03
> +#define ISL29035_DEVICE_ID_MASK (0x7 << ISL29035_DEVICE_ID_SHIFT)
> +#define ISL29035_DEVICE_ID 0x5
> +#define ISL29035_BOUT_SHIFT 0x07
> +#define ISL29035_BOUT_MASK (0x01 << ISL29035_BOUT_SHIFT)
> +
> struct isl29018_chip {
> struct device *dev;
> struct regmap *regmap;
> struct mutex lock;
> + int type;
> unsigned int lux_scale;
> unsigned int lux_uscale;
> unsigned int range;
> @@ -407,23 +415,35 @@ static int isl29018_read_raw(struct iio_dev *indio_dev,
> return ret;
> }
>
> +#define ISL29018_LIGHT_CHANNEL { \
> + .type = IIO_LIGHT, \
> + .indexed = 1, \
> + .channel = 0, \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) | \
> + BIT(IIO_CHAN_INFO_CALIBSCALE), \
> +}
> +
> +#define ISL29018_IR_CHANNEL { \
> + .type = IIO_INTENSITY, \
> + .modified = 1, \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> + .channel2 = IIO_MOD_LIGHT_IR, \
> +}
> +
> +#define ISL29018_PROXIMITY_CHANNEL { \
> + .type = IIO_PROXIMITY, \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> +}
> +
> static const struct iio_chan_spec isl29018_channels[] = {
> - {
> - .type = IIO_LIGHT,
> - .indexed = 1,
> - .channel = 0,
> - .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
> - BIT(IIO_CHAN_INFO_CALIBSCALE),
> - }, {
> - .type = IIO_INTENSITY,
> - .modified = 1,
> - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
> - .channel2 = IIO_MOD_LIGHT_IR,
> - }, {
> - /* Unindexed in current ABI. But perhaps it should be. */
> - .type = IIO_PROXIMITY,
> - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
> - }
> + ISL29018_LIGHT_CHANNEL,
> + ISL29018_IR_CHANNEL,
> + ISL29018_PROXIMITY_CHANNEL,
> +};
> +
> +static const struct iio_chan_spec isl29023_channels[] = {
> + ISL29018_LIGHT_CHANNEL,
> + ISL29018_IR_CHANNEL,
> };
>
> static IIO_DEVICE_ATTR(range, S_IRUGO | S_IWUSR, show_range, store_range, 0);
> @@ -447,16 +467,63 @@ static struct attribute *isl29018_attributes[] = {
> NULL
> };
>
> +static struct attribute *isl29023_attributes[] = {
> + ISL29018_DEV_ATTR(range),
> + ISL29018_CONST_ATTR(range_available),
> + ISL29018_DEV_ATTR(adc_resolution),
> + ISL29018_CONST_ATTR(adc_resolution_available),
These last two are non standard ABI, but they are in the existing driver
(one of the reasons it is still in staging).
> + NULL
> +};
> +
> static const struct attribute_group isl29018_group = {
> .attrs = isl29018_attributes,
> };
>
> +static const struct attribute_group isl29023_group = {
> + .attrs = isl29023_attributes,
> +};
> +
> +static int isl29035_detect(struct isl29018_chip *chip)
> +{
> + int status;
> + unsigned int id;
> +
> + status = regmap_read(chip->regmap, ISL29035_REG_DEVICE_ID, &id);
> + if (status < 0) {
> + dev_err(chip->dev,
> + "Error reading ID register with error %d\n",
> + status);
> + return status;
> + }
> +
> + id = (id & ISL29035_DEVICE_ID_MASK) >> ISL29035_DEVICE_ID_SHIFT;
> +
> + if (id != ISL29035_DEVICE_ID)
> + return -ENODEV;
> +
> + /* clear out brownout bit */
> + return regmap_update_bits(chip->regmap, ISL29035_REG_DEVICE_ID,
> + ISL29035_BOUT_MASK, 0);
> +}
> +
> +enum {
> + isl29018,
> + isl29023,
> + isl29035,
> +};
> +
> static int isl29018_chip_init(struct isl29018_chip *chip)
> {
> int status;
> unsigned int new_adc_bit;
> unsigned int new_range;
>
> + if (chip->type == isl29035) {
> + status = isl29035_detect(chip);
> + if (status < 0)
> + return status;
> + }
> +
> /* Code added per Intersil Application Note 1534:
> * When VDD sinks to approximately 1.8V or below, some of
> * the part's registers may change their state. When VDD
> @@ -517,6 +584,13 @@ static const struct iio_info isl29018_info = {
> .write_raw = &isl29018_write_raw,
> };
>
> +static const struct iio_info isl29023_info = {
> + .attrs = &isl29023_group,
> + .driver_module = THIS_MODULE,
> + .read_raw = &isl29018_read_raw,
> + .write_raw = &isl29018_write_raw,
> +};
> +
> static bool is_volatile_reg(struct device *dev, unsigned int reg)
> {
> switch (reg) {
> @@ -524,6 +598,7 @@ static bool is_volatile_reg(struct device *dev, unsigned int reg)
> case ISL29018_REG_ADD_DATA_MSB:
> case ISL29018_REG_ADD_COMMAND1:
> case ISL29018_REG_TEST:
> + case ISL29035_REG_DEVICE_ID:
> return true;
> default:
> return false;
> @@ -543,6 +618,44 @@ static const struct regmap_config isl29018_regmap_config = {
> .cache_type = REGCACHE_RBTREE,
> };
>
> +/* isl29035_regmap_config: regmap configuration for ISL29035 */
> +static const struct regmap_config isl29035_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .volatile_reg = is_volatile_reg,
> + .max_register = ISL29035_REG_DEVICE_ID,
> + .num_reg_defaults_raw = ISL29035_REG_DEVICE_ID + 1,
> + .cache_type = REGCACHE_RBTREE,
> +};
> +
> +struct chip_info {
> + const struct iio_chan_spec *channels;
> + int num_channels;
> + const struct iio_info *indio_info;
> + const struct regmap_config *regmap_cfg;
> +};
> +
> +static const struct chip_info chip_info_tbl[] = {
> + [isl29018] = {
> + .channels = isl29018_channels,
> + .num_channels = ARRAY_SIZE(isl29018_channels),
> + .indio_info = &isl29018_info,
> + .regmap_cfg = &isl29018_regmap_config,
> + },
> + [isl29023] = {
> + .channels = isl29023_channels,
> + .num_channels = ARRAY_SIZE(isl29023_channels),
> + .indio_info = &isl29023_info,
> + .regmap_cfg = &isl29018_regmap_config,
> + },
> + [isl29035] = {
> + .channels = isl29023_channels,
> + .num_channels = ARRAY_SIZE(isl29023_channels),
> + .indio_info = &isl29023_info,
> + .regmap_cfg = &isl29035_regmap_config,
> + },
> +};
> +
> static int isl29018_probe(struct i2c_client *client,
> const struct i2c_device_id *id)
> {
> @@ -562,13 +675,15 @@ static int isl29018_probe(struct i2c_client *client,
>
> mutex_init(&chip->lock);
>
> + chip->type = id->driver_data;
> chip->lux_scale = 1;
> chip->lux_uscale = 0;
> chip->range = 1000;
> chip->adc_bit = 16;
> chip->suspended = false;
>
> - chip->regmap = devm_regmap_init_i2c(client, &isl29018_regmap_config);
> + chip->regmap = devm_regmap_init_i2c(client,
> + chip_info_tbl[id->driver_data].regmap_cfg);
> if (IS_ERR(chip->regmap)) {
> err = PTR_ERR(chip->regmap);
> dev_err(chip->dev, "regmap initialization failed: %d\n", err);
> @@ -579,9 +694,9 @@ static int isl29018_probe(struct i2c_client *client,
> if (err)
> return err;
>
> - indio_dev->info = &isl29018_info;
> - indio_dev->channels = isl29018_channels;
> - indio_dev->num_channels = ARRAY_SIZE(isl29018_channels);
> + indio_dev->info = chip_info_tbl[id->driver_data].indio_info;
> + indio_dev->channels = chip_info_tbl[id->driver_data].channels;
> + indio_dev->num_channels = chip_info_tbl[id->driver_data].num_channels;
> indio_dev->name = id->name;
> indio_dev->dev.parent = &client->dev;
> indio_dev->modes = INDIO_DIRECT_MODE;
> @@ -633,7 +748,9 @@ static SIMPLE_DEV_PM_OPS(isl29018_pm_ops, isl29018_suspend, isl29018_resume);
> #endif
>
> static const struct i2c_device_id isl29018_id[] = {
> - {"isl29018", 0},
> + {"isl29018", isl29018},
> + {"isl29023", isl29023},
> + {"isl29035", isl29035},
> {}
> };
>
> @@ -641,6 +758,8 @@ MODULE_DEVICE_TABLE(i2c, isl29018_id);
>
> static const struct of_device_id isl29018_of_match[] = {
> { .compatible = "isil,isl29018", },
> + { .compatible = "isil,isl29023", },
> + { .compatible = "isil,isl29035", },
> { },
> };
> MODULE_DEVICE_TABLE(of, isl29018_of_match);
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists