| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAFp+6iEyqmbwMLFrBKD7NVLDAC=b+h1hPKFS=BG4k9D69hn_dg@mail.gmail.com>
Date: Wed, 3 Sep 2014 12:59:27 +0530
From: Vivek Gautam <gautam.vivek@...sung.com>
To: Felipe Balbi <balbi@...com>
Cc: Linux USB Mailing List <linux-usb@...r.kernel.org>,
"linux-samsung-soc@...r.kernel.org"
<linux-samsung-soc@...r.kernel.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
Greg KH <gregkh@...uxfoundation.org>, kishon <kishon@...com>,
Alan Stern <stern@...land.harvard.edu>,
Kukjin Kim <kgene.kim@...sung.com>,
Heikki Krogerus <heikki.krogerus@...ux.intel.com>,
Mathias Nyman <mathias.nyman@...el.com>,
Sergei Shtylyov <sergei.shtylyov@...entembedded.com>,
Jingoo Han <jg1.han@...sung.com>
Subject: Re: [PATCH v6 4/4] phy: exynos5-usbdrd: Calibrate LOS levels for exynos5420/5800
Hi Felipe,
On Tue, Sep 2, 2014 at 8:04 PM, Felipe Balbi <balbi@...com> wrote:
> Hi,
>
> On Tue, Sep 02, 2014 at 04:42:18PM +0530, Vivek Gautam wrote:
>> Adding phy calibrate callback, which facilitates setting certain
>> PHY settings post initialization of the PHY controller.
>> Exynos5420 and Exynos5800 have 28nm USB 3.0 DRD PHY for which
>> the Loss-of-Signal (LOS) Detector Threshold Level as well as
>> Tx-Vboost-Level should be controlled for Super-Speed operations.
>>
>> Additionally set proper time to wait for RxDetect measurement,
>> for desired PHY reference clock, so as to solve issue with enumeration
>> of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive
>> on the controller.
>> We are using CR_port for this purpose to send required data
>> to override the LOS values.
>>
>> On testing with USB 3.0 devices on USB 3.0 port present on
>> SMDK5420, and peach-pit boards should see following message:
>> usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
>>
>> and without this patch, should see below shown message:
>> usb 1-1: new high-speed USB device number 2 using xhci-hcd
>>
>> [Also removed unnecessary extra lines in the register macro definitions]
>>
>> Signed-off-by: Vivek Gautam <gautam.vivek@...sung.com>
>> ---
>> drivers/phy/phy-exynos5-usbdrd.c | 185 ++++++++++++++++++++++++++++++++++----
>> 1 file changed, 170 insertions(+), 15 deletions(-)
>>
>> diff --git a/drivers/phy/phy-exynos5-usbdrd.c b/drivers/phy/phy-exynos5-usbdrd.c
>> index 47f47fe..85742b0 100644
>> --- a/drivers/phy/phy-exynos5-usbdrd.c
>> +++ b/drivers/phy/phy-exynos5-usbdrd.c
>> @@ -37,13 +37,11 @@
>>
>> /* EXYNOS5: USB 3.0 DRD PHY registers */
>> #define EXYNOS5_DRD_LINKSYSTEM 0x04
>> -
>> #define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
>> #define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
>> #define LINKSYSTEM_XHCI_VERSION_CONTROL BIT(27)
>>
>> #define EXYNOS5_DRD_PHYUTMI 0x08
>> -
>> #define PHYUTMI_OTGDISABLE BIT(6)
>> #define PHYUTMI_FORCESUSPEND BIT(1)
>> #define PHYUTMI_FORCESLEEP BIT(0)
>> @@ -51,26 +49,20 @@
>> #define EXYNOS5_DRD_PHYPIPE 0x0c
>>
>> #define EXYNOS5_DRD_PHYCLKRST 0x10
>> -
>> #define PHYCLKRST_EN_UTMISUSPEND BIT(31)
>> -
>> #define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
>> #define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
>> -
>> #define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
>> #define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
>> -
>> #define PHYCLKRST_SSC_EN BIT(20)
>> #define PHYCLKRST_REF_SSP_EN BIT(19)
>> #define PHYCLKRST_REF_CLKDIV2 BIT(18)
>> -
>> #define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
>> #define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
>> #define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
>> #define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
>> #define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
>> #define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
>> -
>> #define PHYCLKRST_FSEL_UTMI_MASK (0x7 << 5)
>> #define PHYCLKRST_FSEL_PIPE_MASK (0x7 << 8)
>> #define PHYCLKRST_FSEL(_x) ((_x) << 5)
>> @@ -78,46 +70,68 @@
>> #define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
>> #define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
>> #define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
>> -
>> #define PHYCLKRST_RETENABLEN BIT(4)
>> -
>> #define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
>> #define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
>> #define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
>> -
>> #define PHYCLKRST_PORTRESET BIT(1)
>> #define PHYCLKRST_COMMONONN BIT(0)
>>
>> #define EXYNOS5_DRD_PHYREG0 0x14
>> +#define PHYREG0_SSC_REF_CLK_SEL BIT(21)
>> +#define PHYREG0_SSC_RANGE BIT(20)
>> +#define PHYREG0_CR_WRITE BIT(19)
>> +#define PHYREG0_CR_READ BIT(18)
>> +#define PHYREG0_CR_DATA_IN(_x) ((_x) << 2)
>> +#define PHYREG0_CR_CAP_DATA BIT(1)
>> +#define PHYREG0_CR_CAP_ADDR BIT(0)
>> +
>> #define EXYNOS5_DRD_PHYREG1 0x18
>> +#define PHYREG1_CR_DATA_OUT(_x) ((_x) << 1)
>> +#define PHYREG1_CR_ACK BIT(0)
>>
>> #define EXYNOS5_DRD_PHYPARAM0 0x1c
>> -
>> #define PHYPARAM0_REF_USE_PAD BIT(31)
>> #define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
>> #define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
>>
>> #define EXYNOS5_DRD_PHYPARAM1 0x20
>> -
>> #define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
>> #define PHYPARAM1_PCS_TXDEEMPH (0x1c)
>>
>> #define EXYNOS5_DRD_PHYTERM 0x24
>>
>> #define EXYNOS5_DRD_PHYTEST 0x28
>> -
>> #define PHYTEST_POWERDOWN_SSP BIT(3)
>> #define PHYTEST_POWERDOWN_HSP BIT(2)
>>
>> #define EXYNOS5_DRD_PHYADP 0x2c
>>
>> #define EXYNOS5_DRD_PHYUTMICLKSEL 0x30
>> -
>
> this and all above are unrelated to $subject.
True, but i have mentioned about this change in the commit message.
It looked so trivial to me that i included it here in this patch.
Will separate it out in a separate patch if you like that. :-)
>
>> #define PHYUTMICLKSEL_UTMI_CLKSEL BIT(2)
>>
>> #define EXYNOS5_DRD_PHYRESUME 0x34
>> #define EXYNOS5_DRD_LINKPORT 0x44
>>
>> +/* USB 3.0 DRD PHY SS Function Control Reg; accessed by CR_PORT */
>> +#define EXYNOS5_DRD_PHYSS_LOSLEVEL_OVRD_IN (0x15)
>> +#define LOSLEVEL_OVRD_IN_LOS_BIAS_5420 (0x5 << 13)
>> +#define LOSLEVEL_OVRD_IN_LOS_BIAS_DEFAULT (0x0 << 13)
>> +#define LOSLEVEL_OVRD_IN_EN (0x1 << 10)
>> +#define LOSLEVEL_OVRD_IN_LOS_LEVEL_DEFAULT (0x9 << 0)
>> +
>> +#define EXYNOS5_DRD_PHYSS_TX_VBOOSTLEVEL_OVRD_IN (0x12)
>> +#define TX_VBOOSTLEVEL_OVRD_IN_VBOOST_5420 (0x5 << 13)
>> +#define TX_VBOOSTLEVEL_OVRD_IN_VBOOST_DEFAULT (0x4 << 13)
>> +
>> +#define EXYNOS5_DRD_PHYSS_LANE0_TX_DEBUG (0x1010)
>> +#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_19M2_20M (0x4 << 4)
>> +#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_24M (0x8 << 4)
>> +#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_25M_26M (0x8 << 4)
>> +#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_48M_50M_52M (0x20 << 4)
>> +#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_62M5 (0x20 << 4)
>> +#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_96M_100M (0x40 << 4)
>> +
>> #define KHZ 1000
>> #define MHZ (KHZ * KHZ)
>>
>> @@ -135,12 +149,14 @@ struct exynos5_usbdrd_phy_config {
>> void (*phy_isol)(struct phy_usb_instance *inst, u32 on);
>> void (*phy_init)(struct exynos5_usbdrd_phy *phy_drd);
>> unsigned int (*set_refclk)(struct phy_usb_instance *inst);
>> + int (*phy_calibrate)(struct phy_usb_instance *inst);
>> };
>>
>> struct exynos5_usbdrd_phy_drvdata {
>> const struct exynos5_usbdrd_phy_config *phy_cfg;
>> u32 pmu_offset_usbdrd0_phy;
>> u32 pmu_offset_usbdrd1_phy;
>> + void (*phy_exynos_calibrate)(struct exynos5_usbdrd_phy *phy_drd);
>> };
>>
>> /**
>> @@ -487,6 +503,142 @@ static int exynos5_usbdrd_phy_power_off(struct phy *phy)
>> return 0;
>> }
>>
>> +static void crport_handshake(struct exynos5_usbdrd_phy *phy_drd,
>> + u32 val, u32 cmd)
>> +{
>> + u32 usec = 100;
>> + u32 result;
>> +
>> + writel(val | cmd, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
>> +
>> + do {
>> + result = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYREG1);
>> + if (result & PHYREG1_CR_ACK)
>> + break;
>> +
>> + udelay(1);
>> + } while (usec-- > 0);
>> +
>> + if (!usec)
>> + dev_err(phy_drd->dev,
>> + "CRPORT handshake timeout1 (0x%08x)\n", val);
>
> if handshake timed out, shouldn't you error out here ? IOW, make this
> function return an int and return an error code from this point ? Why
> would you even continue to the next step ?
Point taken, we should have error'ed out here once timeout occured.
Will update it accordingly.
>
>> +
>> + usec = 100;
>> +
>> + writel(val, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
>> +
>> + do {
>> + result = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYREG1);
>> + if (!(result & PHYREG1_CR_ACK))
>> + break;
>> +
>> + udelay(1);
>> + } while (usec-- > 0);
>> +
>> + if (!usec)
>> + dev_err(phy_drd->dev,
>> + "CRPORT handshake timeout2 (0x%08x)\n", val);
>
> return an error ?
sure
>
>> +}
>> +
>> +static void crport_ctrl_write(struct exynos5_usbdrd_phy *phy_drd,
>> + u32 addr, u32 data)
>> +{
>> + /* Write Address */
>> + writel(PHYREG0_CR_DATA_IN(addr),
>> + phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
>> + crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(addr),
>> + PHYREG0_CR_CAP_ADDR);
>> +
>> + /* Write Data */
>> + writel(PHYREG0_CR_DATA_IN(data),
>> + phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
>> + crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(data),
>> + PHYREG0_CR_CAP_DATA);
>> + crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(data),
>> + PHYREG0_CR_WRITE);
>> +}
>> +
>> +/*
>> + * Override PHY paramaeters using CR_PORT register to calibrate settings
>> + * to meet meet SuperSpeed requirements, on Exynos5420 and Exynos5800 systems,
>> + * which have 28nm USB 3.0 DRD PHY.
>> + */
>> +static void exynos5420_usbdrd_phy_calibrate(struct exynos5_usbdrd_phy *phy_drd)
>> +{
>> + u32 temp;
>> +
>> + /*
>> + * Change los_bias to (0x5) for 28nm PHY from a
>> + * default value (0x0); los_level is set as default
>> + * (0x9) as also reflected in los_level[30:26] bits
>> + * of PHYPARAM0 register.
>> + */
>> + temp = LOSLEVEL_OVRD_IN_LOS_BIAS_5420 |
>> + LOSLEVEL_OVRD_IN_EN |
>> + LOSLEVEL_OVRD_IN_LOS_LEVEL_DEFAULT;
>> + crport_ctrl_write(phy_drd,
>> + EXYNOS5_DRD_PHYSS_LOSLEVEL_OVRD_IN,
>> + temp);
>> +
>> + /*
>> + * Set tx_vboost_lvl to (0x5) for 28nm PHY Tuning,
>> + * to raise Tx signal level from its default value of (0x4)
>> + */
>> + temp = TX_VBOOSTLEVEL_OVRD_IN_VBOOST_5420;
>> + crport_ctrl_write(phy_drd,
>> + EXYNOS5_DRD_PHYSS_TX_VBOOSTLEVEL_OVRD_IN,
>> + temp);
>> +
>> + /*
>> + * Set proper time to wait for RxDetect measurement, for
>> + * desired reference clock of PHY, by tuning the CRPORT
>> + * register LANE0.TX_DEBUG which is internal to PHY.
>> + * This fixes issue with few USB 3.0 devices, which are
>> + * not detected (not even generate interrupts on the bus
>> + * on insertion) without this change.
>> + * e.g. Samsung SUM-TSB16S 3.0 USB drive.
>> + */
>> + switch (phy_drd->extrefclk) {
>> + case EXYNOS5_FSEL_50MHZ:
>> + temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_48M_50M_52M;
>> + break;
>> + case EXYNOS5_FSEL_20MHZ:
>> + case EXYNOS5_FSEL_19MHZ2:
>> + temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_19M2_20M;
>> + break;
>> + case EXYNOS5_FSEL_24MHZ:
>
> why can't this be done during probe() ? Are you going to change external
> reference clock frequency during runtime ? And even if you do,
> wouldn't it be easier to subscribe to clock rate change notifiers
> instead of adding this ->calibrate() ?
Wait, did this patch give an impression that we are changing the reference
clock settings ?
We are actually trying to override some of the PHY parameters, which is
possible only after the controller has been reset.
These PHY parameter overriding (on PHY registers which are not exposed outside)
is done post initialization, only through EXYNOS5_DRD_PHYREG0.
>
> It still looks, to me, that this ->calibrate() thing is unnecessary. We
> have a single user for it and this user could very well get this sorted
> out during probe() or by subscribing to clock rate notifiers.
We can't program these parameters during PHY probe(), since they reset to
their default value after the controller reset.
So we needed a way to do this post initialization, once the controller has been
reset.
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists