| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1410559016.9942.53.camel@joe-AO725>
Date: Fri, 12 Sep 2014 14:56:56 -0700
From: Joe Perches <joe@...ches.com>
To: Chris Ball <chris@...ntf.net>, Ulf Hansson <ulf.hansson@...aro.org>
Cc: linux-mmc@...r.kernel.org, LKML <linux-kernel@...r.kernel.org>
Subject: [PATCH] mmc: Convert pr_warning to pr_warn
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@...ches.com>
---
drivers/mmc/card/block.c | 4 ++--
drivers/mmc/card/queue.c | 6 ++----
drivers/mmc/card/sdio_uart.c | 9 ++++-----
drivers/mmc/core/core.c | 8 ++++----
drivers/mmc/core/mmc.c | 17 +++++++----------
drivers/mmc/core/mmc_ops.c | 4 ++--
drivers/mmc/core/sd.c | 33 ++++++++++++++-------------------
drivers/mmc/core/sdio.c | 7 +++----
drivers/mmc/core/sdio_bus.c | 4 ++--
drivers/mmc/core/sdio_irq.c | 7 +++----
drivers/mmc/host/s3cmci.c | 3 ++-
drivers/mmc/host/sdhci.c | 34 ++++++++++++++++------------------
drivers/mmc/host/tifm_sd.c | 4 ++--
drivers/mmc/host/wbsd.c | 21 ++++++---------------
14 files changed, 69 insertions(+), 92 deletions(-)
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index e248b96..ec8ac2a 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1928,8 +1928,8 @@ static int mmc_blk_issue_rw_rq(struct mmc_queue *mq, struct request *rqc)
case MMC_BLK_ECC_ERR:
if (brq->data.blocks > 1) {
/* Redo read one sector at a time */
- pr_warning("%s: retrying using single block read\n",
- req->rq_disk->disk_name);
+ pr_warn("%s: retrying using single block read\n",
+ req->rq_disk->disk_name);
disable_multi = 1;
break;
}
diff --git a/drivers/mmc/card/queue.c b/drivers/mmc/card/queue.c
index 3e049c1..feea926 100644
--- a/drivers/mmc/card/queue.c
+++ b/drivers/mmc/card/queue.c
@@ -229,14 +229,12 @@ int mmc_init_queue(struct mmc_queue *mq, struct mmc_card *card,
if (bouncesz > 512) {
mqrq_cur->bounce_buf = kmalloc(bouncesz, GFP_KERNEL);
if (!mqrq_cur->bounce_buf) {
- pr_warning("%s: unable to "
- "allocate bounce cur buffer\n",
+ pr_warn("%s: unable to allocate bounce cur buffer\n",
mmc_card_name(card));
}
mqrq_prev->bounce_buf = kmalloc(bouncesz, GFP_KERNEL);
if (!mqrq_prev->bounce_buf) {
- pr_warning("%s: unable to "
- "allocate bounce prev buffer\n",
+ pr_warn("%s: unable to allocate bounce prev buffer\n",
mmc_card_name(card));
kfree(mqrq_cur->bounce_buf);
mqrq_cur->bounce_buf = NULL;
diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c
index f093cea..d2de592 100644
--- a/drivers/mmc/card/sdio_uart.c
+++ b/drivers/mmc/card/sdio_uart.c
@@ -1063,8 +1063,8 @@ static int sdio_uart_probe(struct sdio_func *func,
return -ENOMEM;
if (func->class == SDIO_CLASS_UART) {
- pr_warning("%s: need info on UART class basic setup\n",
- sdio_func_id(func));
+ pr_warn("%s: need info on UART class basic setup\n",
+ sdio_func_id(func));
kfree(port);
return -ENOSYS;
} else if (func->class == SDIO_CLASS_GPS) {
@@ -1082,9 +1082,8 @@ static int sdio_uart_probe(struct sdio_func *func,
break;
}
if (!tpl) {
- pr_warning(
- "%s: can't find tuple 0x91 subtuple 0 (SUBTPL_SIOREG) for GPS class\n",
- sdio_func_id(func));
+ pr_warn("%s: can't find tuple 0x91 subtuple 0 (SUBTPL_SIOREG) for GPS class\n",
+ sdio_func_id(func));
kfree(port);
return -EINVAL;
}
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index e2e1dd4..b1e209f 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -433,8 +433,8 @@ static void mmc_wait_for_req_done(struct mmc_host *host,
*/
if (cmd->sanitize_busy && cmd->error == -ETIMEDOUT) {
if (!mmc_interrupt_hpi(host->card)) {
- pr_warning("%s: %s: Interrupted sanitize\n",
- mmc_hostname(host), __func__);
+ pr_warn("%s: %s: Interrupted sanitize\n",
+ mmc_hostname(host), __func__);
cmd->error = 0;
break;
} else {
@@ -1417,8 +1417,8 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr)
if (!host->ops->start_signal_voltage_switch)
return -EPERM;
if (!host->ops->card_busy)
- pr_warning("%s: cannot verify signal voltage switch\n",
- mmc_hostname(host));
+ pr_warn("%s: cannot verify signal voltage switch\n",
+ mmc_hostname(host));
cmd.opcode = SD_SWITCH_VOLTAGE;
cmd.arg = 0;
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index 69e6273..51085b4 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -226,9 +226,7 @@ static int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd)
"Card will be ignored.\n",
mmc_hostname(card->host));
} else {
- pr_warning("%s: unable to read "
- "EXT_CSD, performance might "
- "suffer.\n",
+ pr_warn("%s: unable to read EXT_CSD, performance might suffer\n",
mmc_hostname(card->host));
err = 0;
}
@@ -790,8 +788,8 @@ static int __mmc_select_powerclass(struct mmc_card *card,
ext_csd->raw_pwr_cl_200_360;
break;
default:
- pr_warning("%s: Voltage range not supported "
- "for power class.\n", mmc_hostname(host));
+ pr_warn("%s: Voltage range not supported for power class\n",
+ mmc_hostname(host));
return -EINVAL;
}
@@ -1432,8 +1430,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
if (err && err != -EBADMSG)
goto free_card;
if (err) {
- pr_warning("%s: Enabling HPI failed\n",
- mmc_hostname(card->host));
+ pr_warn("%s: Enabling HPI failed\n",
+ mmc_hostname(card->host));
err = 0;
} else
card->ext_csd.hpi_en = 1;
@@ -1454,9 +1452,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
* Only if no error, cache is turned on successfully.
*/
if (err) {
- pr_warning("%s: Cache is supported, "
- "but failed to turn on (%d)\n",
- mmc_hostname(card->host), err);
+ pr_warn("%s: Cache is supported, but failed to turn on (%d)\n",
+ mmc_hostname(card->host), err);
card->ext_csd.cache_ctrl = 0;
err = 0;
} else {
diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
index ba0275e..7911e05 100644
--- a/drivers/mmc/core/mmc_ops.c
+++ b/drivers/mmc/core/mmc_ops.c
@@ -649,8 +649,8 @@ int mmc_send_hpi_cmd(struct mmc_card *card, u32 *status)
int err;
if (!card->ext_csd.hpi) {
- pr_warning("%s: Card didn't support HPI command\n",
- mmc_hostname(card->host));
+ pr_warn("%s: Card didn't support HPI command\n",
+ mmc_hostname(card->host));
return -EINVAL;
}
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 2591388..d90a6de 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -229,8 +229,8 @@ static int mmc_read_ssr(struct mmc_card *card)
u32 *ssr;
if (!(card->csd.cmdclass & CCC_APP_SPEC)) {
- pr_warning("%s: card lacks mandatory SD Status "
- "function.\n", mmc_hostname(card->host));
+ pr_warn("%s: card lacks mandatory SD Status function\n",
+ mmc_hostname(card->host));
return 0;
}
@@ -240,8 +240,8 @@ static int mmc_read_ssr(struct mmc_card *card)
err = mmc_app_sd_status(card, ssr);
if (err) {
- pr_warning("%s: problem reading SD Status "
- "register.\n", mmc_hostname(card->host));
+ pr_warn("%s: problem reading SD Status register\n",
+ mmc_hostname(card->host));
err = 0;
goto out;
}
@@ -265,8 +265,8 @@ static int mmc_read_ssr(struct mmc_card *card)
card->ssr.erase_offset = eo * 1000;
}
} else {
- pr_warning("%s: SD Status: Invalid Allocation Unit size.\n",
- mmc_hostname(card->host));
+ pr_warn("%s: SD Status: Invalid Allocation Unit size\n",
+ mmc_hostname(card->host));
}
}
out:
@@ -286,8 +286,7 @@ static int mmc_read_switch(struct mmc_card *card)
return 0;
if (!(card->csd.cmdclass & CCC_SWITCH)) {
- pr_warning("%s: card lacks mandatory switch "
- "function, performance might suffer.\n",
+ pr_warn("%s: card lacks mandatory switch function, performance might suffer\n",
mmc_hostname(card->host));
return 0;
}
@@ -316,7 +315,7 @@ static int mmc_read_switch(struct mmc_card *card)
if (err != -EINVAL && err != -ENOSYS && err != -EFAULT)
goto out;
- pr_warning("%s: problem reading Bus Speed modes.\n",
+ pr_warn("%s: problem reading Bus Speed modes\n",
mmc_hostname(card->host));
err = 0;
@@ -372,8 +371,7 @@ int mmc_sd_switch_hs(struct mmc_card *card)
goto out;
if ((status[16] & 0xF) != 1) {
- pr_warning("%s: Problem switching card "
- "into high-speed mode!\n",
+ pr_warn("%s: Problem switching card into high-speed mode!\n",
mmc_hostname(card->host));
err = 0;
} else {
@@ -440,7 +438,7 @@ static int sd_select_driver_type(struct mmc_card *card, u8 *status)
return err;
if ((status[15] & 0xF) != drive_strength) {
- pr_warning("%s: Problem setting drive strength!\n",
+ pr_warn("%s: Problem setting drive strength!\n",
mmc_hostname(card->host));
return 0;
}
@@ -518,7 +516,7 @@ static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
return err;
if ((status[16] & 0xF) != card->sd_bus_speed)
- pr_warning("%s: Problem setting bus speed mode!\n",
+ pr_warn("%s: Problem setting bus speed mode!\n",
mmc_hostname(card->host));
else {
mmc_set_timing(card->host, timing);
@@ -598,7 +596,7 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status)
return err;
if (((status[15] >> 4) & 0x0F) != current_limit)
- pr_warning("%s: Problem setting current limit!\n",
+ pr_warn("%s: Problem setting current limit!\n",
mmc_hostname(card->host));
}
@@ -727,8 +725,7 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
try_again:
if (!retries) {
ocr &= ~SD_OCR_S18R;
- pr_warning("%s: Skipping voltage switch\n",
- mmc_hostname(host));
+ pr_warn("%s: Skipping voltage switch\n", mmc_hostname(host));
}
/*
@@ -872,9 +869,7 @@ int mmc_sd_setup_card(struct mmc_host *host, struct mmc_card *card,
}
if (ro < 0) {
- pr_warning("%s: host does not "
- "support reading read-only "
- "switch. assuming write-enable.\n",
+ pr_warn("%s: host does not support reading read-only switch, assuming write-enable\n",
mmc_hostname(host));
} else if (ro > 0) {
mmc_card_set_readonly(card);
diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index 3fc40a7..2439e71 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -216,8 +216,8 @@ static int sdio_enable_wide(struct mmc_card *card)
return ret;
if ((ctrl & SDIO_BUS_WIDTH_MASK) == SDIO_BUS_WIDTH_RESERVED)
- pr_warning("%s: SDIO_CCCR_IF is invalid: 0x%02x\n",
- mmc_hostname(card->host), ctrl);
+ pr_warn("%s: SDIO_CCCR_IF is invalid: 0x%02x\n",
+ mmc_hostname(card->host), ctrl);
/* set as 4-bit bus width */
ctrl &= ~SDIO_BUS_WIDTH_MASK;
@@ -605,8 +605,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
try_again:
if (!retries) {
- pr_warning("%s: Skipping voltage switch\n",
- mmc_hostname(host));
+ pr_warn("%s: Skipping voltage switch\n", mmc_hostname(host));
ocr &= ~R4_18V_PRESENT;
}
diff --git a/drivers/mmc/core/sdio_bus.c b/drivers/mmc/core/sdio_bus.c
index 4fa8fef9..e4eb456 100644
--- a/drivers/mmc/core/sdio_bus.c
+++ b/drivers/mmc/core/sdio_bus.c
@@ -177,8 +177,8 @@ static int sdio_bus_remove(struct device *dev)
drv->remove(func);
if (func->irq_handler) {
- pr_warning("WARNING: driver %s did not remove "
- "its interrupt handler!\n", drv->name);
+ pr_warn("WARNING: driver %s did not remove its interrupt handler!\n",
+ drv->name);
sdio_claim_host(func);
sdio_release_irq(func);
sdio_release_host(func);
diff --git a/drivers/mmc/core/sdio_irq.c b/drivers/mmc/core/sdio_irq.c
index 696eca4..09cc67d 100644
--- a/drivers/mmc/core/sdio_irq.c
+++ b/drivers/mmc/core/sdio_irq.c
@@ -69,16 +69,15 @@ static int process_sdio_pending_irqs(struct mmc_host *host)
if (pending & (1 << i)) {
func = card->sdio_func[i - 1];
if (!func) {
- pr_warning("%s: pending IRQ for "
- "non-existent function\n",
+ pr_warn("%s: pending IRQ for non-existent function\n",
mmc_card_id(card));
ret = -EINVAL;
} else if (func->irq_handler) {
func->irq_handler(func);
count++;
} else {
- pr_warning("%s: pending IRQ with no handler\n",
- sdio_func_id(func));
+ pr_warn("%s: pending IRQ with no handler\n",
+ sdio_func_id(func));
ret = -EINVAL;
}
}
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index e4e1a53..94cddf3 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -985,7 +985,8 @@ static int s3cmci_setup_data(struct s3cmci_host *host, struct mmc_data *data)
* one block being transferred. */
if (data->blocks > 1) {
- pr_warning("%s: can't do non-word sized block transfers (blksz %d)\n", __func__, data->blksz);
+ pr_warn("%s: can't do non-word sized block transfers (blksz %d)\n",
+ __func__, data->blksz);
return -EINVAL;
}
}
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 7481bd8..db113ab 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -1754,8 +1754,8 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
ret = regulator_set_voltage(mmc->supply.vqmmc, 2700000,
3600000);
if (ret) {
- pr_warning("%s: Switching to 3.3V signalling voltage "
- " failed\n", mmc_hostname(mmc));
+ pr_warn("%s: Switching to 3.3V signalling voltage failed\n",
+ mmc_hostname(mmc));
return -EIO;
}
}
@@ -1767,8 +1767,8 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
if (!(ctrl & SDHCI_CTRL_VDD_180))
return 0;
- pr_warning("%s: 3.3V regulator output did not became stable\n",
- mmc_hostname(mmc));
+ pr_warn("%s: 3.3V regulator output did not became stable\n",
+ mmc_hostname(mmc));
return -EAGAIN;
case MMC_SIGNAL_VOLTAGE_180:
@@ -1776,8 +1776,8 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
ret = regulator_set_voltage(mmc->supply.vqmmc,
1700000, 1950000);
if (ret) {
- pr_warning("%s: Switching to 1.8V signalling voltage "
- " failed\n", mmc_hostname(mmc));
+ pr_warn("%s: Switching to 1.8V signalling voltage failed\n",
+ mmc_hostname(mmc));
return -EIO;
}
}
@@ -1794,8 +1794,8 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
if (ctrl & SDHCI_CTRL_VDD_180)
return 0;
- pr_warning("%s: 1.8V regulator output did not became stable\n",
- mmc_hostname(mmc));
+ pr_warn("%s: 1.8V regulator output did not became stable\n",
+ mmc_hostname(mmc));
return -EAGAIN;
case MMC_SIGNAL_VOLTAGE_120:
@@ -1803,8 +1803,8 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
ret = regulator_set_voltage(mmc->supply.vqmmc, 1100000,
1300000);
if (ret) {
- pr_warning("%s: Switching to 1.2V signalling voltage "
- " failed\n", mmc_hostname(mmc));
+ pr_warn("%s: Switching to 1.2V signalling voltage failed\n",
+ mmc_hostname(mmc));
return -EIO;
}
}
@@ -2844,8 +2844,7 @@ int sdhci_add_host(struct sdhci_host *host)
if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
if (host->ops->enable_dma) {
if (host->ops->enable_dma(host)) {
- pr_warning("%s: No suitable DMA "
- "available. Falling back to PIO.\n",
+ pr_warn("%s: No suitable DMA available - falling back to PIO\n",
mmc_hostname(mmc));
host->flags &=
~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
@@ -2867,15 +2866,14 @@ int sdhci_add_host(struct sdhci_host *host)
dma_free_coherent(mmc_dev(mmc), ADMA_SIZE,
host->adma_desc, host->adma_addr);
kfree(host->align_buffer);
- pr_warning("%s: Unable to allocate ADMA "
- "buffers. Falling back to standard DMA.\n",
+ pr_warn("%s: Unable to allocate ADMA buffers - falling back to standard DMA\n",
mmc_hostname(mmc));
host->flags &= ~SDHCI_USE_ADMA;
host->adma_desc = NULL;
host->align_buffer = NULL;
} else if (host->adma_addr & 3) {
- pr_warning("%s: unable to allocate aligned ADMA descriptor\n",
- mmc_hostname(mmc));
+ pr_warn("%s: unable to allocate aligned ADMA descriptor\n",
+ mmc_hostname(mmc));
host->flags &= ~SDHCI_USE_ADMA;
dma_free_coherent(mmc_dev(mmc), ADMA_SIZE,
host->adma_desc, host->adma_addr);
@@ -3202,8 +3200,8 @@ int sdhci_add_host(struct sdhci_host *host)
mmc->max_blk_size = (caps[0] & SDHCI_MAX_BLOCK_MASK) >>
SDHCI_MAX_BLOCK_SHIFT;
if (mmc->max_blk_size >= 3) {
- pr_warning("%s: Invalid maximum block size, "
- "assuming 512 bytes\n", mmc_hostname(mmc));
+ pr_warn("%s: Invalid maximum block size, assuming 512 bytes\n",
+ mmc_hostname(mmc));
mmc->max_blk_size = 0;
}
}
diff --git a/drivers/mmc/host/tifm_sd.c b/drivers/mmc/host/tifm_sd.c
index d1760eb..93c4b40 100644
--- a/drivers/mmc/host/tifm_sd.c
+++ b/drivers/mmc/host/tifm_sd.c
@@ -952,8 +952,8 @@ static int tifm_sd_probe(struct tifm_dev *sock)
if (!(TIFM_SOCK_STATE_OCCUPIED
& readl(sock->addr + SOCK_PRESENT_STATE))) {
- pr_warning("%s : card gone, unexpectedly\n",
- dev_name(&sock->dev));
+ pr_warn("%s : card gone, unexpectedly\n",
+ dev_name(&sock->dev));
return rc;
}
diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c
index 1defd5e..9a6dfb0 100644
--- a/drivers/mmc/host/wbsd.c
+++ b/drivers/mmc/host/wbsd.c
@@ -803,8 +803,7 @@ static void wbsd_request(struct mmc_host *mmc, struct mmc_request *mrq)
default:
#ifdef CONFIG_MMC_DEBUG
- pr_warning("%s: Data command %d is not "
- "supported by this controller.\n",
+ pr_warn("%s: Data command %d is not supported by this controller\n",
mmc_hostname(host->mmc), cmd->opcode);
#endif
cmd->error = -EINVAL;
@@ -1429,8 +1428,8 @@ free:
free_dma(dma);
err:
- pr_warning(DRIVER_NAME ": Unable to allocate DMA %d. "
- "Falling back on FIFO.\n", dma);
+ pr_warn(DRIVER_NAME ": Unable to allocate DMA %d - falling back on FIFO\n",
+ dma);
}
static void wbsd_release_dma(struct wbsd_host *host)
@@ -1664,9 +1663,7 @@ static int wbsd_init(struct device *dev, int base, int irq, int dma,
ret = wbsd_scan(host);
if (ret) {
if (pnp && (ret == -ENODEV)) {
- pr_warning(DRIVER_NAME
- ": Unable to confirm device presence. You may "
- "experience lock-ups.\n");
+ pr_warn(DRIVER_NAME ": Unable to confirm device presence - you may experience lock-ups\n");
} else {
wbsd_free_mmc(dev);
return ret;
@@ -1688,10 +1685,7 @@ static int wbsd_init(struct device *dev, int base, int irq, int dma,
*/
if (pnp) {
if ((host->config != 0) && !wbsd_chip_validate(host)) {
- pr_warning(DRIVER_NAME
- ": PnP active but chip not configured! "
- "You probably have a buggy BIOS. "
- "Configuring chip manually.\n");
+ pr_warn(DRIVER_NAME ": PnP active but chip not configured! You probably have a buggy BIOS. Configuring chip manually.\n");
wbsd_chip_config(host);
}
} else
@@ -1884,10 +1878,7 @@ static int wbsd_pnp_resume(struct pnp_dev *pnp_dev)
*/
if (host->config != 0) {
if (!wbsd_chip_validate(host)) {
- pr_warning(DRIVER_NAME
- ": PnP active but chip not configured! "
- "You probably have a buggy BIOS. "
- "Configuring chip manually.\n");
+ pr_warn(DRIVER_NAME ": PnP active but chip not configured! You probably have a buggy BIOS. Configuring chip manually.\n");
wbsd_chip_config(host);
}
}
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists