Message-Id: <1414037002-25528-5-git-send-email-linux@roeck-us.net>
Date:	Wed, 22 Oct 2014 21:03:12 -0700
From:	Guenter Roeck <linux@...ck-us.net>
To:	netdev@...r.kernel.org
Cc:	"David S. Miller" <davem@...emloft.net>,
	Florian Fainelli <f.fainelli@...il.com>,
	Andrew Lunn <andrew@...n.ch>, linux-kernel@...r.kernel.org,
	Guenter Roeck <linux@...ck-us.net>
Subject: [PATCH 04/14] net: dsa: Add support for Marvell 88E6352

Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.

Signed-off-by: Guenter Roeck <linux@...ck-us.net>
---
 MAINTAINERS                 |   5 +
 drivers/net/dsa/Kconfig     |   8 +
 drivers/net/dsa/Makefile    |   3 +
 drivers/net/dsa/mv88e6352.c | 464 ++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/dsa/mv88e6xxx.c |   3 +
 drivers/net/dsa/mv88e6xxx.h |   7 +
 6 files changed, 490 insertions(+)
 create mode 100644 drivers/net/dsa/mv88e6352.c

diff --git a/MAINTAINERS b/MAINTAINERS
index a20df9b..e48a05b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5845,6 +5845,11 @@ M:	Russell King <rmk+kernel@....linux.org.uk>
 S:	Maintained
 F:	drivers/gpu/drm/armada/
 
+MARVELL 88E6352 DSA support
+M:	Guenter Roeck <linux@...ck-us.net>
+S:	Maintained
+F:	drivers/net/dsa/mv88e6352.c
+
 MARVELL GIGABIT ETHERNET DRIVERS (skge/sky2)
 M:	Mirko Lindner <mlindner@...vell.com>
 M:	Stephen Hemminger <stephen@...workplumber.org>
diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index 9234d80..0987c33 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -45,6 +45,14 @@ config NET_DSA_MV88E6171
 	  This enables support for the Marvell 88E6171 ethernet switch
 	  chip.
 
+config NET_DSA_MV88E6352
+	tristate "Marvell 88E6352 ethernet switch chip support"
+	select NET_DSA
+	select NET_DSA_MV88E6XXX
+	select NET_DSA_TAG_EDSA
+	---help---
+	  This enables support for the Marvell 88E6352 ethernet switch chip.
+
 config NET_DSA_BCM_SF2
 	tristate "Broadcom Starfighter 2 Ethernet switch support"
 	depends on HAS_IOMEM
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index 23a90de..e2d51c4 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -7,6 +7,9 @@ endif
 ifdef CONFIG_NET_DSA_MV88E6131
 mv88e6xxx_drv-y += mv88e6131.o
 endif
+ifdef CONFIG_NET_DSA_MV88E6352
+mv88e6xxx_drv-y += mv88e6352.o
+endif
 ifdef CONFIG_NET_DSA_MV88E6171
 mv88e6xxx_drv-y += mv88e6171.o
 endif
diff --git a/drivers/net/dsa/mv88e6352.c b/drivers/net/dsa/mv88e6352.c
new file mode 100644
index 0000000..43a5826
--- /dev/null
+++ b/drivers/net/dsa/mv88e6352.c
@@ -0,0 +1,464 @@
+/*
+ * net/dsa/mv88e6352.c - Marvell 88e6352 switch chip support
+ *
+ * Copyright (c) 2014 Guenter Roeck
+ *
+ * Derived from mv88e6123_61_65.c
+ * Copyright (c) 2008-2009 Marvell Semiconductor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/jiffies.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/platform_device.h>
+#include <linux/phy.h>
+#include <net/dsa.h>
+#include "mv88e6xxx.h"
+
+static int mv88e6352_phy_wait(struct dsa_switch *ds)
+{
+	unsigned long timeout = jiffies + HZ / 10;
+
+	while (time_before(jiffies, timeout)) {
+		int ret;
+
+		ret = REG_READ(REG_GLOBAL2, 0x18);
+		if (ret < 0)
+			return ret;
+
+		if (!(ret & 0x8000))
+			return 0;
+
+		usleep_range(1000, 2000);
+	}
+	return -ETIMEDOUT;
+}
+
+static int __mv88e6352_phy_read(struct dsa_switch *ds, int addr, int regnum)
+{
+	int ret;
+
+	REG_WRITE(REG_GLOBAL2, 0x18, 0x9800 | (addr << 5) | regnum);
+
+	ret = mv88e6352_phy_wait(ds);
+	if (ret < 0)
+		return ret;
+
+	return REG_READ(REG_GLOBAL2, 0x19);
+}
+
+static int __mv88e6352_phy_write(struct dsa_switch *ds, int addr, int regnum,
+				 u16 val)
+{
+	REG_WRITE(REG_GLOBAL2, 0x19, val);
+	REG_WRITE(REG_GLOBAL2, 0x18, 0x9400 | (addr << 5) | regnum);
+
+	return mv88e6352_phy_wait(ds);
+}
+
+static char *mv88e6352_probe(struct device *host_dev, int sw_addr)
+{
+	struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
+	int ret;
+
+	if (bus == NULL)
+		return NULL;
+
+	ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
+	if (ret >= 0) {
+		if (ret == 0x3521)
+			return "Marvell 88E6352 (A0)";
+		if (ret == 0x3522)
+			return "Marvell 88E6352 (A1)";
+		if ((ret & 0xfff0) == 0x3520)
+			return "Marvell 88E6352";
+	}
+
+	return NULL;
+}
+
+static int mv88e6352_switch_reset(struct dsa_switch *ds)
+{
+	unsigned long timeout;
+	int ret;
+	int i;
+
+	/* Set all ports to the disabled state. */
+	for (i = 0; i < 7; i++) {
+		ret = REG_READ(REG_PORT(i), 0x04);
+		REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
+	}
+
+	/* Wait for transmit queues to drain. */
+	usleep_range(2000, 4000);
+
+	/* Reset the switch. Keep PPU active (bit 14, undocumented).
+	 * The PPU needs to be active to support indirect phy register
+	 * accesses through global registers 0x18 and 0x19.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x04, 0xc000);
+
+	/* Wait up to one second for reset to complete. */
+	timeout = jiffies + 1 * HZ;
+	while (time_before(jiffies, timeout)) {
+		ret = REG_READ(REG_GLOBAL, 0x00);
+		if ((ret & 0x8800) == 0x8800)
+			break;
+		usleep_range(1000, 2000);
+	}
+	if (time_after(jiffies, timeout))
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+static int mv88e6352_setup_global(struct dsa_switch *ds)
+{
+	int ret;
+	int i;
+
+	/* Discard packets with excessive collisions,
+	 * mask all interrupt sources, enable PPU (bit 14, undocumented).
+	 */
+	REG_WRITE(REG_GLOBAL, 0x04, 0x6000);
+
+	/* Set the default address aging time to 5 minutes, and
+	 * enable address learn messages to be sent to all message
+	 * ports.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
+
+	/* Configure the priority mapping registers. */
+	ret = mv88e6xxx_config_prio(ds);
+	if (ret < 0)
+		return ret;
+
+	/* Configure the upstream port, and configure the upstream
+	 * port as the port to which ingress and egress monitor frames
+	 * are to be sent.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1110));
+
+	/* Disable remote management for now, and set the switch's
+	 * DSA device number.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x1c, ds->index & 0x1f);
+
+	/* Send all frames with destination addresses matching
+	 * 01:80:c2:00:00:2x to the CPU port.
+	 */
+	REG_WRITE(REG_GLOBAL2, 0x02, 0xffff);
+
+	/* Send all frames with destination addresses matching
+	 * 01:80:c2:00:00:0x to the CPU port.
+	 */
+	REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
+
+	/* Disable the loopback filter, disable flow control
+	 * messages, disable flood broadcast override, disable
+	 * removing of provider tags, disable ATU age violation
+	 * interrupts, disable tag flow control, force flow
+	 * control priority to the highest, and send all special
+	 * multicast frames to the CPU at the highest priority.
+	 */
+	REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
+
+	/* Program the DSA routing table. */
+	for (i = 0; i < 32; i++) {
+		int nexthop = 0x1f;
+
+		if (i != ds->index && i < ds->dst->pd->nr_chips)
+			nexthop = ds->pd->rtable[i] & 0x1f;
+
+		REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop);
+	}
+
+	/* Clear all trunk masks. */
+	for (i = 0; i < 8; i++)
+		REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0x7f);
+
+	/* Clear all trunk mappings. */
+	for (i = 0; i < 16; i++)
+		REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
+
+	/* Disable ingress rate limiting by resetting all ingress
+	 * rate limit registers to their initial state.
+	 */
+	for (i = 0; i < 7; i++)
+		REG_WRITE(REG_GLOBAL2, 0x09, 0x9000 | (i << 8));
+
+	/* Initialise cross-chip port VLAN table to reset defaults. */
+	REG_WRITE(REG_GLOBAL2, 0x0b, 0x9000);
+
+	/* Clear the priority override table. */
+	for (i = 0; i < 16; i++)
+		REG_WRITE(REG_GLOBAL2, 0x0f, 0x8000 | (i << 8));
+
+	/* @@@ initialise AVB (22/23) watchdog (27) sdet (29) registers */
+
+	return 0;
+}
+
+static int mv88e6352_setup_port(struct dsa_switch *ds, int p)
+{
+	int addr = REG_PORT(p);
+	u16 val;
+
+	/* MAC Forcing register: don't force link, speed, duplex
+	 * or flow control state to any particular values on physical
+	 * ports, but force the CPU port and all DSA ports to 1000 Mb/s
+	 * full duplex.
+	 */
+	if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
+		REG_WRITE(addr, 0x01, 0x003e);
+	else
+		REG_WRITE(addr, 0x01, 0x0003);
+
+	/* Do not limit the period of time that this port can be
+	 * paused for by the remote end or the period of time that
+	 * this port can pause the remote end.
+	 */
+	REG_WRITE(addr, 0x02, 0x0000);
+
+	/* Port Control: disable Drop-on-Unlock, disable Drop-on-Lock,
+	 * disable Header mode, enable IGMP/MLD snooping, disable VLAN
+	 * tunneling, determine priority by looking at 802.1p and IP
+	 * priority fields (IP prio has precedence), and set STP state
+	 * to Forwarding.
+	 *
+	 * If this is the CPU link, use DSA or EDSA tagging depending
+	 * on which tagging mode was configured.
+	 *
+	 * If this is a link to another switch, use DSA tagging mode.
+	 *
+	 * If this is the upstream port for this switch, enable
+	 * forwarding of unknown unicasts and multicasts.
+	 */
+	val = 0x0433;
+	if (dsa_is_cpu_port(ds, p)) {
+		if (ds->dst->tag_protocol == DSA_TAG_PROTO_EDSA)
+			val |= 0x3300;
+		else
+			val |= 0x0100;
+	}
+	if (ds->dsa_port_mask & (1 << p))
+		val |= 0x0100;
+	if (p == dsa_upstream_port(ds))
+		val |= 0x000c;
+	REG_WRITE(addr, 0x04, val);
+
+	/* Port Control 1: disable trunking.  Also, if this is the
+	 * CPU port, enable learn messages to be sent to this port.
+	 */
+	REG_WRITE(addr, 0x05, dsa_is_cpu_port(ds, p) ? 0x8000 : 0x0000);
+
+	/* Port based VLAN map: give each port its own address
+	 * database, allow the CPU port to talk to each of the 'real'
+	 * ports, and allow each of the 'real' ports to only talk to
+	 * the upstream port.
+	 */
+	val = (p & 0xf) << 12;
+	if (dsa_is_cpu_port(ds, p))
+		val |= ds->phys_port_mask;
+	else
+		val |= 1 << dsa_upstream_port(ds);
+	REG_WRITE(addr, 0x06, val);
+
+	/* Default VLAN ID and priority: don't set a default VLAN
+	 * ID, and set the default packet priority to zero.
+	 */
+	REG_WRITE(addr, 0x07, 0x0000);
+
+	/* Port Control 2: don't force a good FCS, set the maximum
+	 * frame size to 10240 bytes, don't let the switch add or
+	 * strip 802.1q tags, don't discard tagged or untagged frames
+	 * on this port, do a destination address lookup on all
+	 * received packets as usual, disable ARP mirroring and don't
+	 * send a copy of all transmitted/received frames on this port
+	 * to the CPU.
+	 */
+	REG_WRITE(addr, 0x08, 0x2080);
+
+	/* Egress rate control: disable egress rate control. */
+	REG_WRITE(addr, 0x09, 0x0001);
+
+	/* Egress rate control 2: disable egress rate control. */
+	REG_WRITE(addr, 0x0a, 0x0000);
+
+	/* Port Association Vector: when learning source addresses
+	 * of packets, add the address to the address database using
+	 * a port bitmap that has only the bit for this port set and
+	 * the other bits clear.
+	 */
+	REG_WRITE(addr, 0x0b, 1 << p);
+
+	/* Port ATU control: disable limiting the number of address
+	 * database entries that this port is allowed to use.
+	 */
+	REG_WRITE(addr, 0x0c, 0x0000);
+
+	/* Priority Override: disable DA, SA and VTU priority override. */
+	REG_WRITE(addr, 0x0d, 0x0000);
+
+	/* Port Ethertype: use the Ethertype DSA Ethertype value. */
+	REG_WRITE(addr, 0x0f, ETH_P_EDSA);
+
+	/* Tag Remap: use an identity 802.1p prio -> switch prio
+	 * mapping.
+	 */
+	REG_WRITE(addr, 0x18, 0x3210);
+
+	/* Tag Remap 2: use an identity 802.1p prio -> switch prio
+	 * mapping.
+	 */
+	REG_WRITE(addr, 0x19, 0x7654);
+
+	return 0;
+}
+
+static int mv88e6352_setup(struct dsa_switch *ds)
+{
+	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
+	int ret;
+	int i;
+
+	mutex_init(&ps->smi_mutex);
+	mutex_init(&ps->stats_mutex);
+	mutex_init(&ps->phy_mutex);
+
+	ps->id = REG_READ(REG_PORT(0), 0x03) & 0xfff0;
+
+	ret = mv88e6352_switch_reset(ds);
+	if (ret < 0)
+		return ret;
+
+	/* @@@ initialise vtu and atu */
+
+	ret = mv88e6352_setup_global(ds);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < 7; i++) {
+		ret = mv88e6352_setup_port(ds, i);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int mv88e6352_port_to_phy_addr(int port)
+{
+	if (port >= 0 && port <= 4)
+		return port;
+	return -EINVAL;
+}
+
+static int
+mv88e6352_phy_read(struct dsa_switch *ds, int port, int regnum)
+{
+	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
+	int addr = mv88e6352_port_to_phy_addr(port);
+	int ret;
+
+	if (addr < 0)
+		return addr;
+
+	mutex_lock(&ps->phy_mutex);
+	ret = __mv88e6352_phy_read(ds, addr, regnum);
+	mutex_unlock(&ps->phy_mutex);
+
+	return ret;
+}
+
+static int
+mv88e6352_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
+{
+	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
+	int addr = mv88e6352_port_to_phy_addr(port);
+	int ret;
+
+	if (addr < 0)
+		return addr;
+
+	mutex_lock(&ps->phy_mutex);
+	ret = __mv88e6352_phy_write(ds, addr, regnum, val);
+	mutex_unlock(&ps->phy_mutex);
+
+	return ret;
+}
+
+static struct mv88e6xxx_hw_stat mv88e6352_hw_stats[] = {
+	{ "in_good_octets", 8, 0x00, },
+	{ "in_bad_octets", 4, 0x02, },
+	{ "in_unicast", 4, 0x04, },
+	{ "in_broadcasts", 4, 0x06, },
+	{ "in_multicasts", 4, 0x07, },
+	{ "in_pause", 4, 0x16, },
+	{ "in_undersize", 4, 0x18, },
+	{ "in_fragments", 4, 0x19, },
+	{ "in_oversize", 4, 0x1a, },
+	{ "in_jabber", 4, 0x1b, },
+	{ "in_rx_error", 4, 0x1c, },
+	{ "in_fcs_error", 4, 0x1d, },
+	{ "out_octets", 8, 0x0e, },
+	{ "out_unicast", 4, 0x10, },
+	{ "out_broadcasts", 4, 0x13, },
+	{ "out_multicasts", 4, 0x12, },
+	{ "out_pause", 4, 0x15, },
+	{ "excessive", 4, 0x11, },
+	{ "collisions", 4, 0x1e, },
+	{ "deferred", 4, 0x05, },
+	{ "single", 4, 0x14, },
+	{ "multiple", 4, 0x17, },
+	{ "out_fcs_error", 4, 0x03, },
+	{ "late", 4, 0x1f, },
+	{ "hist_64bytes", 4, 0x08, },
+	{ "hist_65_127bytes", 4, 0x09, },
+	{ "hist_128_255bytes", 4, 0x0a, },
+	{ "hist_256_511bytes", 4, 0x0b, },
+	{ "hist_512_1023bytes", 4, 0x0c, },
+	{ "hist_1024_max_bytes", 4, 0x0d, },
+};
+
+static void
+mv88e6352_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
+{
+	mv88e6xxx_get_strings(ds, ARRAY_SIZE(mv88e6352_hw_stats),
+			      mv88e6352_hw_stats, port, data);
+}
+
+static void
+mv88e6352_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *data)
+{
+	mv88e6xxx_get_ethtool_stats(ds, ARRAY_SIZE(mv88e6352_hw_stats),
+				    mv88e6352_hw_stats, port, data);
+}
+
+static int mv88e6352_get_sset_count(struct dsa_switch *ds)
+{
+	return ARRAY_SIZE(mv88e6352_hw_stats);
+}
+
+struct dsa_switch_driver mv88e6352_switch_driver = {
+	.tag_protocol		= DSA_TAG_PROTO_EDSA,
+	.priv_size		= sizeof(struct mv88e6xxx_priv_state),
+	.probe			= mv88e6352_probe,
+	.setup			= mv88e6352_setup,
+	.set_addr		= mv88e6xxx_set_addr_indirect,
+	.phy_read		= mv88e6352_phy_read,
+	.phy_write		= mv88e6352_phy_write,
+	.poll_link		= mv88e6xxx_poll_link,
+	.get_strings		= mv88e6352_get_strings,
+	.get_ethtool_stats	= mv88e6352_get_ethtool_stats,
+	.get_sset_count		= mv88e6352_get_sset_count,
+};
+
+MODULE_ALIAS("platform:mv88e6352");
diff --git a/drivers/net/dsa/mv88e6xxx.c b/drivers/net/dsa/mv88e6xxx.c
index a6c90cf..8e1090b 100644
--- a/drivers/net/dsa/mv88e6xxx.c
+++ b/drivers/net/dsa/mv88e6xxx.c
@@ -507,6 +507,9 @@ static int __init mv88e6xxx_init(void)
 #if IS_ENABLED(CONFIG_NET_DSA_MV88E6123_61_65)
 	register_switch_driver(&mv88e6123_61_65_switch_driver);
 #endif
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+	register_switch_driver(&mv88e6352_switch_driver);
+#endif
 #if IS_ENABLED(CONFIG_NET_DSA_MV88E6171)
 	register_switch_driver(&mv88e6171_switch_driver);
 #endif
diff --git a/drivers/net/dsa/mv88e6xxx.h b/drivers/net/dsa/mv88e6xxx.h
index 5e5145a..77beff5 100644
--- a/drivers/net/dsa/mv88e6xxx.h
+++ b/drivers/net/dsa/mv88e6xxx.h
@@ -37,6 +37,12 @@ struct mv88e6xxx_priv_state {
 	 */
 	struct mutex	stats_mutex;
 
+	/* This mutex serializes phy access for chips with
+	 * indirect phy addressing. It is unused for chips
+	 * with direct phy access.
+	 */
+	struct mutex phy_mutex;
+
 	int		id; /* switch product id */
 };
 
@@ -70,6 +76,7 @@ void mv88e6xxx_get_ethtool_stats(struct dsa_switch *ds,
 
 extern struct dsa_switch_driver mv88e6131_switch_driver;
 extern struct dsa_switch_driver mv88e6123_61_65_switch_driver;
+extern struct dsa_switch_driver mv88e6352_switch_driver;
 extern struct dsa_switch_driver mv88e6171_switch_driver;
 
 #define REG_READ(addr, reg)						\
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists