early console in setup code early console in decompress_kernel Decompressing Linux... Parsing ELF... done. Booting the kernel. [ 0.000000] Linux version 3.18.0-rc2-00037-g24574709 (kbuild@roam) (gcc version 4.9.1 (Debian 4.9.1-11) ) #136 PREEMPT Mon Oct 27 22:08:31 CST 2014 [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000013ffdfff] usable [ 0.000000] BIOS-e820: [mem 0x0000000013ffe000-0x0000000013ffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] bootconsole [earlyser0] enabled [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.4 present. [ 0.000000] DMI: Bochs Bochs, BIOS Bochs 01/01/2011 [ 0.000000] Hypervisor detected: KVM [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] e820: last_pfn = 0x13ffe max_arch_pfn = 0x1000000 [ 0.000000] MTRR default type: write-back [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 0080000000 mask FF80000000 uncachable [ 0.000000] 1 disabled [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x70406, new 0x7010600070106 [ 0.000000] Scan for SMP in [mem 0x00000000-0x000003ff] [ 0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff] [ 0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff] [ 0.000000] found SMP MP-table at [mem 0x000fdad0-0x000fdadf] mapped at [c00fdad0] [ 0.000000] mpc: fdae0-fdbe8 [ 0.000000] initial memory mapped: [mem 0x00000000-0x029fffff] [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384 [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x13a00000-0x13bfffff] [ 0.000000] [mem 0x13a00000-0x13bfffff] page 4k [ 0.000000] BRK [0x02414000, 0x02414fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x10000000-0x139fffff] [ 0.000000] [mem 0x10000000-0x139fffff] page 4k [ 0.000000] BRK [0x02415000, 0x02415fff] PGTABLE [ 0.000000] BRK [0x02416000, 0x02416fff] PGTABLE [ 0.000000] BRK [0x02417000, 0x02417fff] PGTABLE [ 0.000000] BRK [0x02418000, 0x02418fff] PGTABLE [ 0.000000] BRK [0x02419000, 0x02419fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x00100000-0x0fffffff] [ 0.000000] [mem 0x00100000-0x0fffffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x13c00000-0x13ffdfff] [ 0.000000] [mem 0x13c00000-0x13ffdfff] page 4k [ 0.000000] RAMDISK: [mem 0x13cbd000-0x13feffff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x000FD970 000014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 0x13FFE4B0 000034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 0x13FFFF80 000074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 0x13FFE4F0 0011A9 (v01 BXPC BXDSDT 00000001 INTL 20100528) [ 0.000000] ACPI: FACS 0x13FFFF40 000040 [ 0.000000] ACPI: SSDT 0x13FFF800 000735 (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: APIC 0x13FFF6E0 000078 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 0x13FFF6A0 000038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffb000 ( fee00000) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 319MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 13ffe000 [ 0.000000] low ram: 0 - 13ffe000 [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00 [ 0.000000] kvm-clock: cpu 0, msr 0:13ffc001, primary cpu clock [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] Normal [mem 0x01000000-0x13ffdfff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x0009efff] [ 0.000000] node 0: [mem 0x00100000-0x13ffdfff] [ 0.000000] Initmem setup node 0 [mem 0x00001000-0x13ffdfff] [ 0.000000] On node 0 totalpages: 81820 [ 0.000000] free_area_init_node: node 0, pgdat c1a77280, node_mem_map d385b028 [ 0.000000] DMA zone: 40 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3998 pages, LIFO batch:0 [ 0.000000] Normal zone: 760 pages used for memmap [ 0.000000] Normal zone: 77822 pages, LIFO batch:15 [ 0.000000] Using APIC driver default [ 0.000000] ACPI: PM-Timer IO Port: 0xb008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffb000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 0, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 05, APIC ID 0, APIC INT 05 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 0, APIC INT 09 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0a, APIC ID 0, APIC INT 0a [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0b, APIC ID 0, APIC INT 0b [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 0, APIC INT 01 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 0, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 0, APIC INT 04 [ 0.000000] ACPI: IRQ5 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 0, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 0, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 0, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ10 used by override. [ 0.000000] ACPI: IRQ11 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 0, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 0, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 0, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 0, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] KVM setup async PF for cpu 0 [ 0.000000] kvm-stealtime: cpu 0, msr 18b7c40 [ 0.000000] e820: [mem 0x14000000-0xfeffbfff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 81020 [ 0.000000] Kernel command line: hung_task_panic=1 earlyprintk=ttyS0,115200 debug apic=debug sysrq_always_enabled rcupdate.rcu_cpu_stall_timeout=100 panic=-1 softlockup_panic=1 nmi_watchdog=panic oops=panic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 vga=normal root=/dev/ram0 rw link=/kbuild-tests/run-queue/kvm/i386-randconfig-r2-1027/peterz-queue:master:245747099820df3007f60128b1264fef9d2a69d2:bisect-linux-0/.vmlinuz-245747099820df3007f60128b1264fef9d2a69d2-20141027220906-253-vp branch=peterz-queue/master BOOT_IMAGE=/kernel/i386-randconfig-r2-1027/245747099820df3007f60128b1264fef9d2a69d2/vmlinuz-3.18.0-rc2-00037-g24574709 drbd.minor_count=8 [ 0.000000] sysrq: sysrq always enabled. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] Initializing HighMem for node 0 (00000000:00000000) [ 0.000000] Memory: 299140K/327280K available (5699K kernel code, 1956K rwdata, 3088K rodata, 692K init, 9020K bss, 28140K reserved, 0K highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xfff8b000 - 0xfffff000 ( 464 kB) [ 0.000000] pkmap : 0xff800000 - 0xffa00000 (2048 kB) [ 0.000000] vmalloc : 0xd47fe000 - 0xff7fe000 ( 688 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd3ffe000 ( 319 MB) [ 0.000000] .init : 0xc1a82000 - 0xc1b2f000 ( 692 kB) [ 0.000000] .data : 0xc1591066 - 0xc1a80040 (5051 kB) [ 0.000000] .text : 0xc1000000 - 0xc1591066 (5700 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:2304 nr_irqs:256 0 [ 0.000000] CPU 0 irqstacks, hard=d3408000 soft=d340a000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] bootconsole [earlyser0] disabled [ 0.000000] Linux version 3.18.0-rc2-00037-g24574709 (kbuild@roam) (gcc version 4.9.1 (Debian 4.9.1-11) ) #136 PREEMPT Mon Oct 27 22:08:31 CST 2014 [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000013ffdfff] usable [ 0.000000] BIOS-e820: [mem 0x0000000013ffe000-0x0000000013ffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] bootconsole [earlyser0] enabled [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.4 present. [ 0.000000] DMI: Bochs Bochs, BIOS Bochs 01/01/2011 [ 0.000000] Hypervisor detected: KVM [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] e820: last_pfn = 0x13ffe max_arch_pfn = 0x1000000 [ 0.000000] MTRR default type: write-back [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 0080000000 mask FF80000000 uncachable [ 0.000000] 1 disabled [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x70406, new 0x7010600070106 [ 0.000000] Scan for SMP in [mem 0x00000000-0x000003ff] [ 0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff] [ 0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff] [ 0.000000] found SMP MP-table at [mem 0x000fdad0-0x000fdadf] mapped at [c00fdad0] [ 0.000000] mpc: fdae0-fdbe8 [ 0.000000] initial memory mapped: [mem 0x00000000-0x029fffff] [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384 [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x13a00000-0x13bfffff] [ 0.000000] [mem 0x13a00000-0x13bfffff] page 4k [ 0.000000] BRK [0x02414000, 0x02414fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x10000000-0x139fffff] [ 0.000000] [mem 0x10000000-0x139fffff] page 4k [ 0.000000] BRK [0x02415000, 0x02415fff] PGTABLE [ 0.000000] BRK [0x02416000, 0x02416fff] PGTABLE [ 0.000000] BRK [0x02417000, 0x02417fff] PGTABLE [ 0.000000] BRK [0x02418000, 0x02418fff] PGTABLE [ 0.000000] BRK [0x02419000, 0x02419fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x00100000-0x0fffffff] [ 0.000000] [mem 0x00100000-0x0fffffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x13c00000-0x13ffdfff] [ 0.000000] [mem 0x13c00000-0x13ffdfff] page 4k [ 0.000000] RAMDISK: [mem 0x13cbd000-0x13feffff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x000FD970 000014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 0x13FFE4B0 000034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 0x13FFFF80 000074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 0x13FFE4F0 0011A9 (v01 BXPC BXDSDT 00000001 INTL 20100528) [ 0.000000] ACPI: FACS 0x13FFFF40 000040 [ 0.000000] ACPI: SSDT 0x13FFF800 000735 (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: APIC 0x13FFF6E0 000078 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 0x13FFF6A0 000038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffb000 ( fee00000) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 319MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 13ffe000 [ 0.000000] low ram: 0 - 13ffe000 [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00 [ 0.000000] kvm-clock: cpu 0, msr 0:13ffc001, primary cpu clock [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] Normal [mem 0x01000000-0x13ffdfff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x0009efff] [ 0.000000] node 0: [mem 0x00100000-0x13ffdfff] [ 0.000000] Initmem setup node 0 [mem 0x00001000-0x13ffdfff] [ 0.000000] On node 0 totalpages: 81820 [ 0.000000] free_area_init_node: node 0, pgdat c1a77280, node_mem_map d385b028 [ 0.000000] DMA zone: 40 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3998 pages, LIFO batch:0 [ 0.000000] Normal zone: 760 pages used for memmap [ 0.000000] Normal zone: 77822 pages, LIFO batch:15 [ 0.000000] Using APIC driver default [ 0.000000] ACPI: PM-Timer IO Port: 0xb008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffb000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 0, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 05, APIC ID 0, APIC INT 05 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 0, APIC INT 09 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0a, APIC ID 0, APIC INT 0a [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0b, APIC ID 0, APIC INT 0b [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 0, APIC INT 01 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 0, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 0, APIC INT 04 [ 0.000000] ACPI: IRQ5 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 0, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 0, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 0, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ10 used by override. [ 0.000000] ACPI: IRQ11 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 0, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 0, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 0, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 0, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] KVM setup async PF for cpu 0 [ 0.000000] kvm-stealtime: cpu 0, msr 18b7c40 [ 0.000000] e820: [mem 0x14000000-0xfeffbfff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 81020 [ 0.000000] Kernel command line: hung_task_panic=1 earlyprintk=ttyS0,115200 debug apic=debug sysrq_always_enabled rcupdate.rcu_cpu_stall_timeout=100 panic=-1 softlockup_panic=1 nmi_watchdog=panic oops=panic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 vga=normal root=/dev/ram0 rw link=/kbuild-tests/run-queue/kvm/i386-randconfig-r2-1027/peterz-queue:master:245747099820df3007f60128b1264fef9d2a69d2:bisect-linux-0/.vmlinuz-245747099820df3007f60128b1264fef9d2a69d2-20141027220906-253-vp branch=peterz-queue/master BOOT_IMAGE=/kernel/i386-randconfig-r2-1027/245747099820df3007f60128b1264fef9d2a69d2/vmlinuz-3.18.0-rc2-00037-g24574709 drbd.minor_count=8 [ 0.000000] sysrq: sysrq always enabled. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] Initializing HighMem for node 0 (00000000:00000000) [ 0.000000] Memory: 299140K/327280K available (5699K kernel code, 1956K rwdata, 3088K rodata, 692K init, 9020K bss, 28140K reserved, 0K highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xfff8b000 - 0xfffff000 ( 464 kB) [ 0.000000] pkmap : 0xff800000 - 0xffa00000 (2048 kB) [ 0.000000] vmalloc : 0xd47fe000 - 0xff7fe000 ( 688 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd3ffe000 ( 319 MB) [ 0.000000] .init : 0xc1a82000 - 0xc1b2f000 ( 692 kB) [ 0.000000] .data : 0xc1591066 - 0xc1a80040 (5051 kB) [ 0.000000] .text : 0xc1000000 - 0xc1591066 (5700 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:2304 nr_irqs:256 0 [ 0.000000] CPU 0 irqstacks, hard=d3408000 soft=d340a000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] bootconsole [earlyser0] disabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.000000] ... CHAINHASH_SIZE: 32768 [ 0.000000] memory used by lock dependency info: 5167 kB [ 0.000000] per task-struct memory footprint: 1920 bytes [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Detected 2693.530 MHz processor [ 0.006666] Calibrating delay loop (skipped) preset value.. 5389.52 BogoMIPS (lpj=8978433) [ 0.006672] pid_max: default: 32768 minimum: 301 [ 0.007599] ACPI: Core revision 20140926 [ 0.013717] ACPI: All ACPI Tables successfully acquired [ 0.014899] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.016041] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.017515] Initializing cgroup subsys freezer [ 0.018486] Initializing cgroup subsys blkio [ 0.020015] Initializing cgroup subsys perf_event [ 0.021025] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.021025] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.023338] CPU: Intel Common KVM processor (fam: 0f, model: 06, stepping: 01) [ 0.029583] ftrace: allocating 27249 entries in 54 pages [ 0.037049] Performance Events: unsupported Netburst CPU model 6 no PMU driver, software events only. [ 0.041183] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.043342] Getting VERSION: 50014 [ 0.044140] Getting VERSION: 50014 [ 0.044935] Getting ID: 0 [ 0.045649] Getting ID: f000000 [ 0.046424] Getting LVT0: 8700 [ 0.046674] Getting LVT1: 8400 [ 0.047570] enabled ExtINT on CPU#0 [ 0.050230] ENABLING IO-APIC IRQs [ 0.051038] init IO_APIC IRQs [ 0.051781] apic 0 pin 0 not connected [ 0.052657] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1) [ 0.053371] IOAPIC[0]: Set routing entry (0-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1) [ 0.055033] IOAPIC[0]: Set routing entry (0-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1) [ 0.056689] IOAPIC[0]: Set routing entry (0-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1) [ 0.058330] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1) [ 0.060022] IOAPIC[0]: Set routing entry (0-5 -> 0x35 -> IRQ 5 Mode:1 Active:0 Dest:1) [ 0.061657] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1) [ 0.063355] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1) [ 0.065480] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1) [ 0.066689] IOAPIC[0]: Set routing entry (0-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1) [ 0.068332] IOAPIC[0]: Set routing entry (0-10 -> 0x3a -> IRQ 10 Mode:1 Active:0 Dest:1) [ 0.070029] IOAPIC[0]: Set routing entry (0-11 -> 0x3b -> IRQ 11 Mode:1 Active:0 Dest:1) [ 0.073356] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1) [ 0.075287] IOAPIC[0]: Set routing entry (0-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:1) [ 0.076690] IOAPIC[0]: Set routing entry (0-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:1) [ 0.078339] IOAPIC[0]: Set routing entry (0-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:1) [ 0.080018] apic 0 pin 16 not connected [ 0.080854] apic 0 pin 17 not connected [ 0.081686] apic 0 pin 18 not connected [ 0.082519] apic 0 pin 19 not connected [ 0.083336] apic 0 pin 20 not connected [ 0.084169] apic 0 pin 21 not connected [ 0.084993] apic 0 pin 22 not connected [ 0.086670] apic 0 pin 23 not connected [ 0.087649] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.088686] Using local APIC timer interrupts. [ 0.088686] calibrating APIC timer ... [ 0.093333] ... lapic delta = 6250137 [ 0.093333] ... PM-Timer delta = 357973 [ 0.093333] ... PM-Timer result ok [ 0.093333] ..... delta 6250137 [ 0.093333] ..... mult: 268441366 [ 0.093333] ..... calibration result: 3333406 [ 0.093333] ..... CPU clock speed is 2693.2447 MHz. [ 0.093333] ..... host bus clock speed is 1000.0406 MHz. [ 0.095459] prandom: seed boundary self test passed [ 0.096996] prandom: 100 self tests passed [ 0.098679] regulator-dummy: no parameters [ 0.099912] NET: Registered protocol family 16 [ 0.100985] ACPI: bus type PCI registered [ 0.101829] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.103604] PCI : PCI BIOS area is rw and x. Use pci=nobios if you want it NX. [ 0.105364] PCI: PCI BIOS revision 2.10 entry at 0xfc6d5, last bus=0 [ 0.106671] PCI: Using configuration type 1 for base access [ 0.128121] ACPI: Added _OSI(Module Device) [ 0.129631] ACPI: Added _OSI(Processor Device) [ 0.130034] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.131730] ACPI: Added _OSI(Processor Aggregator Device) [ 0.138503] IOAPIC[0]: Set routing entry (0-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1) [ 0.153878] ACPI: Interpreter enabled [ 0.155203] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140926/hwxface-580) [ 0.157760] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140926/hwxface-580) [ 0.161147] ACPI: (supports S0 S3 S5) [ 0.162446] ACPI: Using IOAPIC for interrupt routing [ 0.163420] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.188120] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.190018] acpi PNP0A03:00: _OSC: OS supports [Segments MSI] [ 0.191994] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM [ 0.194349] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 0.201570] acpiphp: Slot [3] registered [ 0.203144] acpiphp: Slot [4] registered [ 0.203460] acpiphp: Slot [5] registered [ 0.205045] acpiphp: Slot [6] registered [ 0.206776] acpiphp: Slot [7] registered [ 0.208247] acpiphp: Slot [8] registered [ 0.210119] acpiphp: Slot [9] registered [ 0.211610] acpiphp: Slot [10] registered [ 0.213435] acpiphp: Slot [11] registered [ 0.214842] acpiphp: Slot [12] registered [ 0.216432] acpiphp: Slot [13] registered [ 0.216777] acpiphp: Slot [14] registered [ 0.218370] acpiphp: Slot [15] registered [ 0.220472] acpiphp: Slot [24] registered [ 0.222014] acpiphp: Slot [25] registered [ 0.223444] acpiphp: Slot [26] registered [ 0.224821] acpiphp: Slot [27] registered [ 0.226786] acpiphp: Slot [28] registered [ 0.228135] acpiphp: Slot [29] registered [ 0.230117] acpiphp: Slot [30] registered [ 0.231478] acpiphp: Slot [31] registered [ 0.232987] PCI host bridge to bus 0000:00 [ 0.233342] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.234806] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7] [ 0.236674] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff] [ 0.238324] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff] [ 0.240006] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff] [ 0.241829] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 [ 0.244348] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100 [ 0.248005] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180 [ 0.253727] pci 0000:00:01.1: reg 0x20: [io 0xc1c0-0xc1cf] [ 0.256704] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.258602] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.260005] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.261690] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.264041] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000 [ 0.266015] pci 0000:00:01.3: quirk: [io 0xb000-0xb03f] claimed by PIIX4 ACPI [ 0.266690] pci 0000:00:01.3: quirk: [io 0xb100-0xb10f] claimed by PIIX4 SMB [ 0.270739] pci 0000:00:02.0: [1013:00b8] type 00 class 0x030000 [ 0.276702] pci 0000:00:02.0: reg 0x10: [mem 0xfc000000-0xfdffffff pref] [ 0.280057] pci 0000:00:02.0: reg 0x14: [mem 0xfebf0000-0xfebf0fff] [ 0.291877] pci 0000:00:02.0: reg 0x30: [mem 0xfebe0000-0xfebeffff pref] [ 0.294621] pci 0000:00:03.0: [8086:100e] type 00 class 0x020000 [ 0.298141] pci 0000:00:03.0: reg 0x10: [mem 0xfeba0000-0xfebbffff] [ 0.301402] pci 0000:00:03.0: reg 0x14: [io 0xc000-0xc03f] [ 0.310015] pci 0000:00:03.0: reg 0x30: [mem 0xfebc0000-0xfebdffff pref] [ 0.312649] pci 0000:00:04.0: [1af4:1001] type 00 class 0x010000 [ 0.314778] pci 0000:00:04.0: reg 0x10: [io 0xc040-0xc07f] [ 0.318058] pci 0000:00:04.0: reg 0x14: [mem 0xfebf1000-0xfebf1fff] [ 0.328980] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000 [ 0.331424] pci 0000:00:05.0: reg 0x10: [io 0xc080-0xc0bf] [ 0.334718] pci 0000:00:05.0: reg 0x14: [mem 0xfebf2000-0xfebf2fff] [ 0.345710] pci 0000:00:06.0: [1af4:1001] type 00 class 0x010000 [ 0.348107] pci 0000:00:06.0: reg 0x10: [io 0xc0c0-0xc0ff] [ 0.351400] pci 0000:00:06.0: reg 0x14: [mem 0xfebf3000-0xfebf3fff] [ 0.361628] pci 0000:00:07.0: [1af4:1001] type 00 class 0x010000 [ 0.364765] pci 0000:00:07.0: reg 0x10: [io 0xc100-0xc13f] [ 0.368062] pci 0000:00:07.0: reg 0x14: [mem 0xfebf4000-0xfebf4fff] [ 0.377674] pci 0000:00:08.0: [1af4:1001] type 00 class 0x010000 [ 0.380727] pci 0000:00:08.0: reg 0x10: [io 0xc140-0xc17f] [ 0.384067] pci 0000:00:08.0: reg 0x14: [mem 0xfebf5000-0xfebf5fff] [ 0.391932] pci 0000:00:09.0: [1af4:1001] type 00 class 0x010000 [ 0.393836] pci 0000:00:09.0: reg 0x10: [io 0xc180-0xc1bf] [ 0.395817] pci 0000:00:09.0: reg 0x14: [mem 0xfebf6000-0xfebf6fff] [ 0.403613] pci 0000:00:0a.0: [8086:25ab] type 00 class 0x088000 [ 0.405801] pci 0000:00:0a.0: reg 0x10: [mem 0xfebf7000-0xfebf700f] [ 0.411525] pci_bus 0000:00: on NUMA node 0 [ 0.414989] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11) [ 0.417062] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11) [ 0.419298] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11) [ 0.421524] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11) [ 0.423523] ACPI: PCI Interrupt Link [LNKS] (IRQs *9) [ 0.426086] ACPI: Enabled 16 GPEs in block 00 to 0F [ 0.427789] vgaarb: setting as boot device: PCI:0000:00:02.0 [ 0.429254] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 0.430016] vgaarb: loaded [ 0.433337] vgaarb: bridge control possible 0000:00:02.0 [ 0.435355] ACPI: bus type USB registered [ 0.436829] usbcore: registered new interface driver usbfs [ 0.438344] usbcore: registered new interface driver hub [ 0.440122] usbcore: registered new device driver usb [ 0.441741] pps_core: LinuxPPS API ver. 1 registered [ 0.443337] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.446202] wmi: Mapper loaded [ 0.446887] PCI: Using ACPI for IRQ routing [ 0.448099] PCI: pci_cache_line_size set to 64 bytes [ 0.449226] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] [ 0.450025] e820: reserve RAM buffer [mem 0x13ffe000-0x13ffffff] [ 0.452084] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.453643] Switched to clocksource kvm-clock [ 0.474986] FS-Cache: Loaded [ 0.475814] CacheFiles: Loaded [ 0.476636] pnp: PnP ACPI init [ 0.477532] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1) [ 0.479541] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.480734] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1) [ 0.482416] pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.483587] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1) [ 0.485279] pnp 00:02: Plug and Play ACPI device, IDs PNP0f13 (active) [ 0.486469] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1) [ 0.488119] pnp 00:03: [dma 2] [ 0.488924] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.490141] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1) [ 0.491825] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active) [ 0.493042] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1) [ 0.494750] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.495943] IOAPIC[0]: Set routing entry (0-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1) [ 0.497645] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.499388] pnp: PnP ACPI: found 7 devices [ 0.539033] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.540060] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.541058] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.542126] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff] [ 0.543228] NET: Registered protocol family 1 [ 0.544146] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.545193] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 0.546225] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.547322] pci 0000:00:02.0: Video device with shadowed ROM [ 0.548408] PCI: CLS 0 bytes, default 64 [ 0.549663] Unpacking initramfs... [ 0.668083] debug: unmapping init [mem 0xd3cbd000-0xd3feffff] [ 0.670631] apm: BIOS not found. [ 0.672933] NatSemi SCx200 Driver [ 0.675701] futex hash table entries: 256 (order: 1, 13312 bytes) [ 0.677782] Initialise system trusted keyring [ 0.680561] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.695548] zpool: loaded [ 0.696271] zbud: loaded [ 0.697522] VFS: Disk quotas dquot_6.5.2 [ 0.698521] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.700871] fuse init (API version 7.23) [ 0.702783] NILFS version 2 loaded [ 0.703622] msgmni has been set to 584 [ 0.707373] Key type asymmetric registered [ 0.708252] Asymmetric key parser 'x509' registered [ 0.709369] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.711092] io scheduler noop registered [ 0.711955] io scheduler cfq registered (default) [ 0.712876] start plist test [ 0.714968] end plist test [ 0.717368] rbtree testing -> 12711 cycles [ 1.219661] augmented rbtree testing [ 1.673486] tsc: Refined TSC clocksource calibration: 2693.403 MHz [ 1.813547] -> 15984 cycles [ 1.854266] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.855295] cpqphp: Compaq Hot Plug PCI Controller Driver version: 0.9.8 [ 1.857267] no IO addresses supplied [ 1.858255] cirrusfb 0000:00:02.0: Cirrus Logic chipset on PCI bus, RAM (4096 kB) at 0xfc000000 [ 1.860337] fbcon: CL Picasso4 (fb0) is primary device [ 2.473483] Console: switching to colour frame buffer device 80x30 [ 3.130213] usbcore: registered new interface driver smscufx [ 3.424557] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 3.988286] ACPI: Power Button [PWRF] [ 4.291374] GHES: HEST is not enabled! [ 4.585360] ERST DBG: ERST support is disabled. [ 4.900829] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 5.236674] serial 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 5.830254] Cyclades driver 2.6 [ 6.148697] MOXA Smartio/Industio family driver version 2.0.5 [ 6.426394] lp: driver loaded but no devices found [ 6.726037] Applicom driver: $Id: ac.c,v 1.30 2000/03/22 16:03:57 dwmw2 Exp $ [ 7.043091] ac.o: No PCI boards found. [ 7.378408] ac.o: For an ISA board you must supply memory and irq parameters. [ 7.721633] Non-volatile memory driver v1.3 [ 8.066160] toshiba: not a supported Toshiba laptop [ 8.411519] scx200_gpio: no SCx200 gpio present [ 8.745600] nsc_gpio initializing [ 9.092883] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 9.805069] [drm] Initialized drm 1.1.0 20060810 [ 10.144191] usbcore: registered new interface driver rtsx_usb [ 10.479754] usbcore: registered new interface driver viperboard [ 10.803560] Uniform Multi-Platform E-IDE driver [ 11.126907] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 11.455884] ohci-pci: OHCI PCI platform driver [ 11.778616] ohci-platform: OHCI generic platform driver [ 12.104200] driver u132_hcd [ 12.427539] usbcore: registered new interface driver usblp [ 12.761647] usbcore: registered new interface driver usbtmc [ 13.085039] usbcore: registered new interface driver appledisplay [ 13.405643] ftdi_elan: driver ftdi-elan [ 13.712106] usbcore: registered new interface driver ftdi-elan [ 14.019635] usbcore: registered new interface driver isight_firmware [ 14.322166] usbcore: registered new interface driver uss720 [ 14.614693] uss720: v0.6:USB Parport Cable driver for Cables using the Lucent Technologies USS720 Chip [ 15.196382] uss720: NOTE: this is a special purpose driver to allow nonstandard [ 15.772688] uss720: protocols (eg. bitbang) over USS720 usb to parallel cables [ 16.374947] uss720: If you just want to connect to a printer, use usblp instead [ 17.023557] usbcore: registered new interface driver sisusb [ 17.349736] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 18.003395] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 18.365160] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 18.830775] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 19.752478] usbcore: registered new interface driver aiptek [ 20.154848] usbcore: registered new interface driver gtco [ 20.542700] usbcore: registered new interface driver hanwang [ 20.894798] mk712: device not present [ 21.330396] usbcore: registered new interface driver sur40 [ 21.860669] apanel: Fujitsu BIOS signature 'FJKEYINF' not found... [ 22.215999] usbcore: registered new interface driver ati_remote2 [ 22.588010] cm109: Keymap for Komunikate KIP1000 phone loaded [ 22.948133] usbcore: registered new interface driver cm109 [ 23.297242] cm109: CM109 phone driver: 20080805 (C) Alfred E. Heggestad [ 23.655398] input: PC Speaker as /devices/platform/pcspkr/input/input3 [ 24.008316] usbcore: registered new interface driver yealink [ 24.353622] rtc (null): invalid alarm value: 1900-1-27 0:0:0 [ 24.686136] rtc-test rtc-test.0: rtc core: registered test as rtc0 [ 25.009192] rtc (null): invalid alarm value: 1900-1-27 0:0:0 [ 25.349463] rtc-test rtc-test.1: rtc core: registered test as rtc1 [ 25.725051] i2c /dev entries driver [ 26.014902] usbcore: registered new interface driver i2c-diolan-u2c [ 26.309366] pps_parport: parallel port PPS client [ 26.605710] sdhci: Secure Digital Host Controller Interface driver [ 26.901963] sdhci: Copyright(c) Pierre Ossman [ 27.173022] usbcore: registered new interface driver ushc [ 27.451479] hidraw: raw HID events driver (C) Jiri Kosina [ 27.733152] hv_vmbus: registering driver hid_hyperv [ 28.061656] usbcore: registered new interface driver usbhid [ 28.354495] usbhid: USB HID core driver [ 28.651491] dell_wmi: No known WMI GUID found [ 28.952284] acerhdf: Acer Aspire One Fan driver, v.0.5.26 [ 29.242717] acerhdf: unknown (unsupported) BIOS version Bochs/Bochs/Bochs, please report, aborting! [ 29.822971] fujitsu_tablet: Unknown (using defaults) [ 30.113772] hv_vmbus: registering driver hv_balloon [ 30.420948] intel_rapl: driver does not support CPU family 15 model 6 [ 30.718026] oprofile: using NMI interrupt. [ 31.012651] [ 31.012651] printing PIC contents [ 31.880529] ... PIC IMR: ffff [ 31.883679] ... PIC IRR: 1013 [ 32.442282] ... PIC ISR: 0000 [ 32.721796] ... PIC ELCR: 0c00 [ 33.047363] printing local APIC contents on CPU#0/0: [ 33.050530] ... APIC ID: 00000000 (0) [ 33.050530] ... APIC VERSION: 00050014 [ 33.050530] ... APIC TASKPRI: 00000000 (00) [ 33.050530] ... APIC PROCPRI: 00000000 [ 33.050530] ... APIC LDR: 01000000 [ 33.050530] ... APIC DFR: ffffffff [ 33.050530] ... APIC SPIV: 000001ff [ 33.050530] ... APIC ISR field: [ 33.050530] 0000000000000000000000000000000000000000000000000000000000000000 [ 33.050530] ... APIC TMR field: [ 33.050530] 0000000002000000000000000000000000000000000000000000000000000000 [ 33.050530] ... APIC IRR field: [ 33.050530] 0000000000000000000000000000000000000000000000000000000000008000 [ 33.050530] ... APIC ESR: 00000000 [ 33.050530] ... APIC ICR: 00000831 [ 33.050530] ... APIC ICR2: 01000000 [ 33.050530] ... APIC LVTT: 000000ef [ 33.050530] ... APIC LVTPC: 00010000 [ 33.050530] ... APIC LVT0: 00010700 [ 33.050530] ... APIC LVT1: 00000400 [ 33.050530] ... APIC LVTERR: 000000fe [ 33.050530] ... APIC TMICT: 0002a6a4 [ 33.050530] ... APIC TMCCT: 00000000 [ 33.050530] ... APIC TDCR: 00000003 [ 33.050530] [ 38.820925] number of MP IRQ sources: 15. [ 38.963877] number of IO-APIC #0 registers: 24. [ 39.107704] testing the IO APIC....................... [ 39.256273] IO APIC #0...... [ 39.408592] .... register #00: 00000000 [ 39.563485] ....... : physical APIC id: 00 [ 39.727889] ....... : Delivery Type: 0 [ 39.897668] ....... : LTS : 0 [ 40.066432] .... register #01: 00170011 [ 40.238617] ....... : max redirection entries: 17 [ 40.422225] ....... : PRQ implemented: 0 [ 40.594405] ....... : IO APIC version: 11 [ 40.769676] .... register #02: 00000000 [ 40.943408] ....... : arbitration: 00 [ 41.120956] .... IRQ redirection table: [ 41.299134] 1 0 0 0 0 0 0 00 [ 41.495091] 0 0 0 0 0 1 1 31 [ 41.699725] 0 0 0 0 0 1 1 30 [ 41.896106] 0 0 0 0 0 1 1 33 [ 42.085097] 1 0 0 0 0 1 1 34 [ 42.287984] 1 1 0 0 0 1 1 35 [ 42.480785] 0 0 0 0 0 1 1 36 [ 42.681602] 0 0 0 0 0 1 1 37 [ 42.873897] 0 0 0 0 0 1 1 38 [ 43.065284] 0 1 0 0 0 1 1 39 [ 43.248055] 1 1 0 0 0 1 1 3A [ 43.432024] 1 1 0 0 0 1 1 3B [ 43.605451] 0 0 0 0 0 1 1 3C [ 43.779594] 0 0 0 0 0 1 1 3D [ 43.945771] 0 0 0 0 0 1 1 3E [ 44.112925] 0 0 0 0 0 1 1 3F [ 44.273711] 1 0 0 0 0 0 0 00 [ 44.596443] 1 0 0 0 0 0 0 00 [ 44.772629] 1 0 0 0 0 0 0 00 [ 44.954556] 1 0 0 0 0 0 0 00 [ 45.100470] 1 0 0 0 0 0 0 00 [ 45.256548] 1 0 0 0 0 0 0 00 [ 45.397789] 1 0 0 0 0 0 0 00 [ 45.540016] 1 0 0 0 0 0 0 00 [ 45.662764] IRQ to pin mappings: [ 45.786809] IRQ0 -> 0:2 [ 45.910144] IRQ1 -> 0:1 [ 46.035356] IRQ3 -> 0:3 [ 46.223477] IRQ4 -> 0:4 [ 46.445928] IRQ5 -> 0:5 [ 46.676945] IRQ6 -> 0:6 [ 46.800536] IRQ7 -> 0:7 [ 46.920217] IRQ8 -> 0:8 [ 47.039480] IRQ9 -> 0:9 [ 47.167445] IRQ10 -> 0:10 [ 47.400438] IRQ11 -> 0:11 [ 47.524904] IRQ12 -> 0:12 [ 47.649161] IRQ13 -> 0:13 [ 47.795604] IRQ14 -> 0:14 [ 47.949769] IRQ15 -> 0:15 [ 48.123485] .................................... done. [ 48.244185] Using IPI Shortcut mode [ 48.368008] Loading compiled-in X.509 certificates [ 48.503393] Loaded X.509 cert 'Magrathea: Glacier signing key: df4910b72788bfceac2e4e34cf477fae3fb013db' [ 48.965973] Running ring buffer tests... [ 59.150434] finished [ 59.302049] CPU 0: [ 59.447660] events: 2806 [ 59.594214] dropped bytes: 0 [ 59.739810] alloced bytes: 218228 [ 59.889745] written bytes: 214072 [ 60.039797] biggest event: 44 [ 60.201621] smallest event: 0 [ 60.363903] read events: 2806 [ 60.525876] lost events: 0 [ 60.684143] total events: 2806 [ 60.846773] recorded len bytes: 218228 [ 61.006898] recorded size bytes: 214072 [ 61.166431] Ring buffer PASSED! [ 61.332275] debug: unmapping init [mem 0xc1a82000-0xc1b2efff] [ 61.499903] Write protecting the kernel text: 5704k [ 61.704925] Write protecting the kernel read-only data: 3092k [ 61.922622] NX-protecting the kernel data: 6584k Kernel tests: Boot OK! [ 67.921981] random: trinity urandom read with 3 bits of entropy available [ 82.400935] sock: process `trinity-main' is using obsolete setsockopt SO_BSDCOMPAT [ 122.018008] Bits 55-60 of /proc/PID/pagemap entries are about to stop being page-shift some time soon. See the linux/Documentation/vm/pagemap.txt for details. [ 122.133639] warning: process `trinity-c0' used the obsolete bdflush system call [ 122.133640] Fix your initscripts? [ 122.133905] trinity-c0 (23733) uses deprecated remap_file_pages() syscall. See Documentation/vm/remap_file_pages.txt. [ 122.247299] ------------[ cut here ]------------ [ 122.247328] WARNING: CPU: 0 PID: 61 at kernel/sched/core.c:7312 __might_sleep+0x50/0x249() [ 122.247334] do not call blocking ops when !TASK_RUNNING; state=2 set at [] prepare_to_wait+0x3c/0x5f [ 122.247339] Modules linked in: [ 122.247349] CPU: 0 PID: 61 Comm: kworker/u2:1 Not tainted 3.18.0-rc2-00037-g24574709 #136 [ 122.247350] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 122.247368] Workqueue: netns cleanup_net [ 122.247377] c1071d83 d2b83dd8 d2b83dac c15887b1 d2b83dc8 c104c4c6 00001c90 c1068ebf [ 122.247383] 00000000 c17b67e3 0000026d d2b83de0 c104c508 00000009 d2b83dd8 c17b5d4b [ 122.247388] d2b83df4 d2b83e0c c1068ebf c17b5cec 00001c90 c17b5d4b 00000002 c106ffd9 [ 122.247389] Call Trace: [ 122.247393] [] ? down_trylock+0x23/0x2c [ 122.247402] [] dump_stack+0x16/0x18 [ 122.247413] [] warn_slowpath_common+0x66/0x7d [ 122.247416] [] ? __might_sleep+0x50/0x249 [ 122.247419] [] warn_slowpath_fmt+0x2b/0x2f [ 122.247422] [] __might_sleep+0x50/0x249 [ 122.247424] [] ? prepare_to_wait+0x3c/0x5f [ 122.247426] [] ? prepare_to_wait+0x3c/0x5f [ 122.247432] [] mutex_lock_nested+0x23/0x347 [ 122.247436] [] ? trace_hardirqs_on+0xb/0xd [ 122.247439] [] ? _raw_spin_unlock_irqrestore+0x66/0x78 [ 122.247445] [] rtnl_lock+0x14/0x16 [ 122.247449] [] default_device_exit_batch+0x54/0xf3 [ 122.247452] [] ? rtnl_unlock+0xd/0xf [ 122.247454] [] ? __wake_up_sync+0x12/0x12 [ 122.247461] [] ops_exit_list+0x20/0x40 [ 122.247464] [] cleanup_net+0xbe/0x140 [ 122.247473] [] process_one_work+0x29e/0x643 [ 122.247479] [] worker_thread+0x23a/0x311 [ 122.247482] [] ? rescuer_thread+0x204/0x204 [ 122.247486] [] kthread+0xbe/0xc3 [ 122.247490] [] ret_from_kernel_thread+0x20/0x30 [ 122.247492] [] ? kthread_stop+0x364/0x364 [ 122.247495] ---[ end trace 2073c37ae3c8b3b4 ]--- [ 157.390879] Unregister pv shared memory for cpu 0 [ 157.593564] reboot: Restarting system [ 157.737319] reboot: machine restart Elapsed time: 160 qemu-system-x86_64 -cpu kvm64 -enable-kvm -kernel /kernel/i386-randconfig-r2-1027/245747099820df3007f60128b1264fef9d2a69d2/vmlinuz-3.18.0-rc2-00037-g24574709 -append 'hung_task_panic=1 earlyprintk=ttyS0,115200 debug apic=debug sysrq_always_enabled rcupdate.rcu_cpu_stall_timeout=100 panic=-1 softlockup_panic=1 nmi_watchdog=panic oops=panic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 vga=normal root=/dev/ram0 rw link=/kbuild-tests/run-queue/kvm/i386-randconfig-r2-1027/peterz-queue:master:245747099820df3007f60128b1264fef9d2a69d2:bisect-linux-0/.vmlinuz-245747099820df3007f60128b1264fef9d2a69d2-20141027220906-253-vp branch=peterz-queue/master BOOT_IMAGE=/kernel/i386-randconfig-r2-1027/245747099820df3007f60128b1264fef9d2a69d2/vmlinuz-3.18.0-rc2-00037-g24574709 drbd.minor_count=8' -initrd /kernel-tests/initrd/yocto-minimal-i386.cgz -m 320 -smp 1 -net nic,vlan=1,model=e1000 -net user,vlan=1 -boot order=nc -no-reboot -watchdog i6300esb -rtc base=localtime -drive file=/fs/LABEL=KVM/disk0-yocto-vp-26,media=disk,if=virtio -drive file=/fs/LABEL=KVM/disk1-yocto-vp-26,media=disk,if=virtio -drive file=/fs/LABEL=KVM/disk2-yocto-vp-26,media=disk,if=virtio -drive file=/fs/LABEL=KVM/disk3-yocto-vp-26,media=disk,if=virtio -drive file=/fs/LABEL=KVM/disk4-yocto-vp-26,media=disk,if=virtio -drive file=/fs/LABEL=KVM/disk5-yocto-vp-26,media=disk,if=virtio -pidfile /dev/shm/kboot/pid-yocto-vp-26 -serial file:/dev/shm/kboot/serial-yocto-vp-26 -daemonize -display none -monitor null