| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Mon, 10 Nov 2014 00:30:26 -0800
From: Dmitry Torokhov <dmitry.torokhov@...il.com>
To: Dudley Du <dudley.dulixin@...il.com>
Cc: rydberg@...omail.se, Dudley Du <dudl@...ress.com>,
bleung@...gle.com, linux-input@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH v9 03/18] input: cyapa: add gen3 trackpad device basic
functions support
On Mon, Nov 03, 2014 at 04:32:55PM +0800, Dudley Du wrote:
> Based on the cyapa core, add the gen3 trackpad device's basic functions
> supported, so gen3 trackpad device can work with kernel input system.
> The basic function is absolutely same as previous cyapa driver.
> TEST=test on Chromebooks.
>
> Signed-off-by: Dudley Du <dudl@...ress.com>
> ---
> drivers/input/mouse/Makefile | 3 +-
> drivers/input/mouse/cyapa.c | 90 ++++-
> drivers/input/mouse/cyapa.h | 1 +
> drivers/input/mouse/cyapa_gen3.c | 788 +++++++++++++++++++++++++++++++++++++++
> 4 files changed, 880 insertions(+), 2 deletions(-)
> create mode 100644 drivers/input/mouse/cyapa_gen3.c
>
> diff --git a/drivers/input/mouse/Makefile b/drivers/input/mouse/Makefile
> index dda507f..4bf6c83 100644
> --- a/drivers/input/mouse/Makefile
> +++ b/drivers/input/mouse/Makefile
> @@ -8,7 +8,7 @@ obj-$(CONFIG_MOUSE_AMIGA) += amimouse.o
> obj-$(CONFIG_MOUSE_APPLETOUCH) += appletouch.o
> obj-$(CONFIG_MOUSE_ATARI) += atarimouse.o
> obj-$(CONFIG_MOUSE_BCM5974) += bcm5974.o
> -obj-$(CONFIG_MOUSE_CYAPA) += cyapa.o
> +obj-$(CONFIG_MOUSE_CYAPA) += cyapatp.o
> obj-$(CONFIG_MOUSE_GPIO) += gpio_mouse.o
> obj-$(CONFIG_MOUSE_INPORT) += inport.o
> obj-$(CONFIG_MOUSE_LOGIBM) += logibm.o
> @@ -23,6 +23,7 @@ obj-$(CONFIG_MOUSE_SYNAPTICS_I2C) += synaptics_i2c.o
> obj-$(CONFIG_MOUSE_SYNAPTICS_USB) += synaptics_usb.o
> obj-$(CONFIG_MOUSE_VSXXXAA) += vsxxxaa.o
>
> +cyapatp-objs := cyapa.o cyapa_gen3.o
> psmouse-objs := psmouse-base.o synaptics.o focaltech.o
>
> psmouse-$(CONFIG_MOUSE_PS2_ALPS) += alps.o
> diff --git a/drivers/input/mouse/cyapa.c b/drivers/input/mouse/cyapa.c
> index 5029618..cb81baf 100644
> --- a/drivers/input/mouse/cyapa.c
> +++ b/drivers/input/mouse/cyapa.c
> @@ -234,6 +234,9 @@ static int cyapa_check_is_operational(struct cyapa *cyapa)
> return ret;
>
> switch (cyapa->gen) {
> + case CYAPA_GEN3:
> + cyapa->ops = &cyapa_gen3_ops;
> + break;
> default:
> return -ENODEV;
> }
> @@ -284,7 +287,85 @@ out:
> */
> static int cyapa_get_state(struct cyapa *cyapa)
> {
> - return -ENODEV;
> + int ret;
> + u8 status[BL_STATUS_SIZE];
> + u8 cmd[32];
> + /* The i2c address of gen4 and gen5 trackpad device must be even. */
> + bool even_addr = ((cyapa->client->addr & 0x0001) == 0);
> + bool smbus = false;
> + int retries = 2;
> +
> + cyapa->state = CYAPA_STATE_NO_DEVICE;
> +
> + /*
> + * Get trackpad status by reading 3 registers starting from 0.
> + * If the device is in the bootloader, this will be BL_HEAD.
> + * If the device is in operation mode, this will be the DATA regs.
> + *
> + */
> + ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET, BL_STATUS_SIZE,
> + status);
> +
> + /*
> + * On smbus systems in OP mode, the i2c_reg_read will fail with
> + * -ETIMEDOUT. In this case, try again using the smbus equivalent
> + * command. This should return a BL_HEAD indicating CYAPA_STATE_OP.
> + */
> + if (cyapa->smbus && (ret == -ETIMEDOUT || ret == -ENXIO)) {
> + if (!even_addr)
> + ret = cyapa_read_block(cyapa,
> + CYAPA_CMD_BL_STATUS, status);
> + smbus = true;
> + }
> + if (ret != BL_STATUS_SIZE)
> + goto error;
> +
> + /*
> + * Detect trackpad protocol based on characristic registers and bits.
> + */
> + do {
> + cyapa->status[REG_OP_STATUS] = status[REG_OP_STATUS];
> + cyapa->status[REG_BL_STATUS] = status[REG_BL_STATUS];
> + cyapa->status[REG_BL_ERROR] = status[REG_BL_ERROR];
> +
> + if (cyapa->gen == CYAPA_GEN_UNKNOWN ||
> + cyapa->gen == CYAPA_GEN3) {
> + ret = cyapa_gen3_ops.state_parse(cyapa,
> + status, BL_STATUS_SIZE);
> + if (ret == 0)
> + goto out_detected;
> + }
> +
> + /*
> + * Cannot detect communication protocol based on current
> + * charateristic registers and bits.
> + * So write error command to do further detection.
> + * this method only valid on I2C bus.
> + * for smbus interface, it won't have overwrite issue.
> + */
I do not quite understand this, can you re-phrase?
> + if (!smbus) {
> + cmd[0] = 0x00;
> + cmd[1] = 0x00;
> + ret = cyapa_i2c_write(cyapa, 0, 2, cmd);
> + if (ret)
> + goto error;
> +
> + msleep(50);
> +
> + ret = cyapa_i2c_read(cyapa, BL_HEAD_OFFSET,
> + BL_STATUS_SIZE, status);
> + if (ret < 0)
> + goto error;
> + }
> + } while (--retries > 0 && !smbus);
> +
> + goto error;
> +
> +out_detected:
> + return 0;
> +
> +error:
> + return (ret < 0) ? ret : -EAGAIN;
> }
>
> /*
> @@ -421,6 +502,8 @@ u16 cyapa_pwr_cmd_to_sleep_time(u8 pwr_mode)
> */
> static int cyapa_initialize(struct cyapa *cyapa)
> {
> + int ret = 0;
> +
> cyapa->state = CYAPA_STATE_NO_DEVICE;
> cyapa->gen = CYAPA_GEN_UNKNOWN;
> mutex_init(&cyapa->state_sync_lock);
> @@ -433,6 +516,11 @@ static int cyapa_initialize(struct cyapa *cyapa)
> cyapa->suspend_sleep_time =
> cyapa_pwr_cmd_to_sleep_time(cyapa->suspend_power_mode);
>
> + if (cyapa_gen3_ops.initialize)
> + ret = cyapa_gen3_ops.initialize(cyapa);
> + if (ret)
> + return ret;
> +
> return cyapa_detect(cyapa);
> }
>
> diff --git a/drivers/input/mouse/cyapa.h b/drivers/input/mouse/cyapa.h
> index ee97d7c..b281dcb 100644
> --- a/drivers/input/mouse/cyapa.h
> +++ b/drivers/input/mouse/cyapa.h
> @@ -317,5 +317,6 @@ u16 cyapa_pwr_cmd_to_sleep_time(u8 pwr_mode);
>
>
> extern const char unique_str[];
> +extern const struct cyapa_dev_ops cyapa_gen3_ops;
>
> #endif
> diff --git a/drivers/input/mouse/cyapa_gen3.c b/drivers/input/mouse/cyapa_gen3.c
> new file mode 100644
> index 0000000..bd00c6e
> --- /dev/null
> +++ b/drivers/input/mouse/cyapa_gen3.c
> @@ -0,0 +1,788 @@
> +/*
> + * Cypress APA trackpad with I2C interface
> + *
> + * Author: Dudley Du <dudl@...ress.com>
> + * Further cleanup and restructuring by:
> + * Daniel Kurtz <djkurtz@...omium.org>
> + * Benson Leung <bleung@...omium.org>
> + *
> + * Copyright (C) 2011-2014 Cypress Semiconductor, Inc.
> + * Copyright (C) 2011-2012 Google, Inc.
> + *
> + * This file is subject to the terms and conditions of the GNU General Public
> + * License. See the file COPYING in the main directory of this archive for
> + * more details.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/input.h>
> +#include <linux/input/mt.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include "cyapa.h"
> +
> +
> +#define GEN3_MAX_FINGERS 5
> +#define GEN3_FINGER_NUM(x) (((x) >> 4) & 0x07)
> +
> +#define BLK_HEAD_BYTES 32
> +
> +/* Macro for register map group offset. */
> +#define PRODUCT_ID_SIZE 16
> +#define QUERY_DATA_SIZE 27
> +#define REG_PROTOCOL_GEN_QUERY_OFFSET 20
> +
> +#define REG_OFFSET_DATA_BASE 0x0000
> +#define REG_OFFSET_COMMAND_BASE 0x0028
> +#define REG_OFFSET_QUERY_BASE 0x002a
> +
> +#define CYAPA_OFFSET_SOFT_RESET REG_OFFSET_COMMAND_BASE
> +#define OP_RECALIBRATION_MASK 0x80
> +#define OP_REPORT_BASELINE_MASK 0x40
> +#define REG_OFFSET_MAX_BASELINE 0x0026
> +#define REG_OFFSET_MIN_BASELINE 0x0027
> +
> +#define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1)
> +#define SET_POWER_MODE_DELAY 10000 /* unit: us */
> +#define SET_POWER_MODE_TRIES 5
> +
> +/*
> + * CYAPA trackpad device states.
> + * Used in register 0x00, bit1-0, DeviceStatus field.
> + * Other values indicate device is in an abnormal state and must be reset.
> + */
> +#define CYAPA_DEV_NORMAL 0x03
> +#define CYAPA_DEV_BUSY 0x01
> +
> +#define CYAPA_FW_BLOCK_SIZE 64
> +#define CYAPA_FW_READ_SIZE 16
> +#define CYAPA_FW_HDR_START 0x0780
> +#define CYAPA_FW_HDR_BLOCK_COUNT 2
> +#define CYAPA_FW_HDR_BLOCK_START (CYAPA_FW_HDR_START / CYAPA_FW_BLOCK_SIZE)
> +#define CYAPA_FW_HDR_SIZE (CYAPA_FW_HDR_BLOCK_COUNT * \
> + CYAPA_FW_BLOCK_SIZE)
> +#define CYAPA_FW_DATA_START 0x0800
> +#define CYAPA_FW_DATA_BLOCK_COUNT 480
> +#define CYAPA_FW_DATA_BLOCK_START (CYAPA_FW_DATA_START / CYAPA_FW_BLOCK_SIZE)
> +#define CYAPA_FW_DATA_SIZE (CYAPA_FW_DATA_BLOCK_COUNT * \
> + CYAPA_FW_BLOCK_SIZE)
> +#define CYAPA_FW_SIZE (CYAPA_FW_HDR_SIZE + CYAPA_FW_DATA_SIZE)
> +#define CYAPA_CMD_LEN 16
> +
> +#define GEN3_BL_IDLE_FW_MAJ_VER_OFFSET 0x0b
> +#define GEN3_BL_IDLE_FW_MIN_VER_OFFSET (GEN3_BL_IDLE_FW_MAJ_VER_OFFSET + 1)
> +
> +
> +struct cyapa_touch {
> + /*
> + * high bits or x/y position value
> + * bit 7 - 4: high 4 bits of x position value
> + * bit 3 - 0: high 4 bits of y position value
> + */
> + u8 xy_hi;
> + u8 x_lo; /* low 8 bits of x position value. */
> + u8 y_lo; /* low 8 bits of y position value. */
> + u8 pressure;
> + /* id range is 1 - 15. It is incremented with every new touch. */
> + u8 id;
> +} __packed;
> +
> +struct cyapa_reg_data {
> + /*
> + * bit 0 - 1: device status
> + * bit 3 - 2: power mode
> + * bit 6 - 4: reserved
> + * bit 7: interrupt valid bit
> + */
> + u8 device_status;
> + /*
> + * bit 7 - 4: number of fingers currently touching pad
> + * bit 3: valid data check bit
> + * bit 2: middle mechanism button state if exists
> + * bit 1: right mechanism button state if exists
> + * bit 0: left mechanism button state if exists
> + */
> + u8 finger_btn;
> + /* CYAPA reports up to 5 touches per packet. */
> + struct cyapa_touch touches[5];
> +} __packed;
> +
> +static const u8 bl_activate[] = { 0x00, 0xff, 0x38, 0x00, 0x01, 0x02, 0x03,
> + 0x04, 0x05, 0x06, 0x07 };
> +static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03,
> + 0x04, 0x05, 0x06, 0x07 };
> +static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04,
> + 0x05, 0x06, 0x07 };
> +
> +
> + /* for byte read/write command */
> +#define CMD_RESET 0
> +#define CMD_POWER_MODE 1
> +#define CMD_DEV_STATUS 2
> +#define CMD_REPORT_MAX_BASELINE 3
> +#define CMD_REPORT_MIN_BASELINE 4
> +#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
> +#define CYAPA_SMBUS_RESET SMBUS_BYTE_CMD(CMD_RESET)
> +#define CYAPA_SMBUS_POWER_MODE SMBUS_BYTE_CMD(CMD_POWER_MODE)
> +#define CYAPA_SMBUS_DEV_STATUS SMBUS_BYTE_CMD(CMD_DEV_STATUS)
> +#define CYAPA_SMBUS_MAX_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE)
> +#define CYAPA_SMBUS_MIN_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE)
> +
> + /* for group registers read/write command */
> +#define REG_GROUP_DATA 0
> +#define REG_GROUP_CMD 2
> +#define REG_GROUP_QUERY 3
> +#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
> +#define CYAPA_SMBUS_GROUP_DATA SMBUS_GROUP_CMD(REG_GROUP_DATA)
> +#define CYAPA_SMBUS_GROUP_CMD SMBUS_GROUP_CMD(REG_GROUP_CMD)
> +#define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY)
> +
> + /* for register block read/write command */
> +#define CMD_BL_STATUS 0
> +#define CMD_BL_HEAD 1
> +#define CMD_BL_CMD 2
> +#define CMD_BL_DATA 3
> +#define CMD_BL_ALL 4
> +#define CMD_BLK_PRODUCT_ID 5
> +#define CMD_BLK_HEAD 6
> +#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))
> +
> +/* register block read/write command in bootloader mode */
> +#define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS)
> +#define CYAPA_SMBUS_BL_HEAD SMBUS_BLOCK_CMD(CMD_BL_HEAD)
> +#define CYAPA_SMBUS_BL_CMD SMBUS_BLOCK_CMD(CMD_BL_CMD)
> +#define CYAPA_SMBUS_BL_DATA SMBUS_BLOCK_CMD(CMD_BL_DATA)
> +#define CYAPA_SMBUS_BL_ALL SMBUS_BLOCK_CMD(CMD_BL_ALL)
> +
> +/* register block read/write command in operational mode */
> +#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
> +#define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD)
> +
> + /* for byte read/write command */
> +#define CMD_RESET 0
> +#define CMD_POWER_MODE 1
> +#define CMD_DEV_STATUS 2
> +#define CMD_REPORT_MAX_BASELINE 3
> +#define CMD_REPORT_MIN_BASELINE 4
> +#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
> +#define CYAPA_SMBUS_RESET SMBUS_BYTE_CMD(CMD_RESET)
> +#define CYAPA_SMBUS_POWER_MODE SMBUS_BYTE_CMD(CMD_POWER_MODE)
> +#define CYAPA_SMBUS_DEV_STATUS SMBUS_BYTE_CMD(CMD_DEV_STATUS)
> +#define CYAPA_SMBUS_MAX_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE)
> +#define CYAPA_SMBUS_MIN_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE)
> +
> + /* for group registers read/write command */
> +#define REG_GROUP_DATA 0
> +#define REG_GROUP_CMD 2
> +#define REG_GROUP_QUERY 3
> +#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
> +#define CYAPA_SMBUS_GROUP_DATA SMBUS_GROUP_CMD(REG_GROUP_DATA)
> +#define CYAPA_SMBUS_GROUP_CMD SMBUS_GROUP_CMD(REG_GROUP_CMD)
> +#define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY)
> +
> + /* for register block read/write command */
> +#define CMD_BL_STATUS 0
> +#define CMD_BL_HEAD 1
> +#define CMD_BL_CMD 2
> +#define CMD_BL_DATA 3
> +#define CMD_BL_ALL 4
> +#define CMD_BLK_PRODUCT_ID 5
> +#define CMD_BLK_HEAD 6
> +#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))
> +
> +/* register block read/write command in bootloader mode */
> +#define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS)
> +#define CYAPA_SMBUS_BL_HEAD SMBUS_BLOCK_CMD(CMD_BL_HEAD)
> +#define CYAPA_SMBUS_BL_CMD SMBUS_BLOCK_CMD(CMD_BL_CMD)
> +#define CYAPA_SMBUS_BL_DATA SMBUS_BLOCK_CMD(CMD_BL_DATA)
> +#define CYAPA_SMBUS_BL_ALL SMBUS_BLOCK_CMD(CMD_BL_ALL)
> +
> +/* register block read/write command in operational mode */
> +#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
> +#define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD)
> +
> +struct cyapa_cmd_len {
> + u8 cmd;
> + u8 len;
> +};
> +
> +/* maps generic CYAPA_CMD_* code to the I2C equivalent */
> +static const struct cyapa_cmd_len cyapa_i2c_cmds[] = {
> + { CYAPA_OFFSET_SOFT_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */
> + { REG_OFFSET_COMMAND_BASE + 1, 1 }, /* CYAPA_CMD_POWER_MODE */
> + { REG_OFFSET_DATA_BASE, 1 }, /* CYAPA_CMD_DEV_STATUS */
> + { REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) },
> + /* CYAPA_CMD_GROUP_DATA */
> + { REG_OFFSET_COMMAND_BASE, 0 }, /* CYAPA_CMD_GROUP_CMD */
> + { REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE }, /* CYAPA_CMD_GROUP_QUERY */
> + { BL_HEAD_OFFSET, 3 }, /* CYAPA_CMD_BL_STATUS */
> + { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_HEAD */
> + { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_CMD */
> + { BL_DATA_OFFSET, 16 }, /* CYAPA_CMD_BL_DATA */
> + { BL_HEAD_OFFSET, 32 }, /* CYAPA_CMD_BL_ALL */
> + { REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE },
> + /* CYAPA_CMD_BLK_PRODUCT_ID */
> + { REG_OFFSET_DATA_BASE, 32 }, /* CYAPA_CMD_BLK_HEAD */
> + { REG_OFFSET_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */
> + { REG_OFFSET_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */
> +};
> +
> +static const struct cyapa_cmd_len cyapa_smbus_cmds[] = {
> + { CYAPA_SMBUS_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */
> + { CYAPA_SMBUS_POWER_MODE, 1 }, /* CYAPA_CMD_POWER_MODE */
> + { CYAPA_SMBUS_DEV_STATUS, 1 }, /* CYAPA_CMD_DEV_STATUS */
> + { CYAPA_SMBUS_GROUP_DATA, sizeof(struct cyapa_reg_data) },
> + /* CYAPA_CMD_GROUP_DATA */
> + { CYAPA_SMBUS_GROUP_CMD, 2 }, /* CYAPA_CMD_GROUP_CMD */
> + { CYAPA_SMBUS_GROUP_QUERY, QUERY_DATA_SIZE },
> + /* CYAPA_CMD_GROUP_QUERY */
> + { CYAPA_SMBUS_BL_STATUS, 3 }, /* CYAPA_CMD_BL_STATUS */
> + { CYAPA_SMBUS_BL_HEAD, 16 }, /* CYAPA_CMD_BL_HEAD */
> + { CYAPA_SMBUS_BL_CMD, 16 }, /* CYAPA_CMD_BL_CMD */
> + { CYAPA_SMBUS_BL_DATA, 16 }, /* CYAPA_CMD_BL_DATA */
> + { CYAPA_SMBUS_BL_ALL, 32 }, /* CYAPA_CMD_BL_ALL */
> + { CYAPA_SMBUS_BLK_PRODUCT_ID, PRODUCT_ID_SIZE },
> + /* CYAPA_CMD_BLK_PRODUCT_ID */
> + { CYAPA_SMBUS_BLK_HEAD, 16 }, /* CYAPA_CMD_BLK_HEAD */
> + { CYAPA_SMBUS_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */
> + { CYAPA_SMBUS_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */
> +};
> +
> +static bool data_reporting_started;
Why is this a global?
> +
> +
> +/*
> + * cyapa_smbus_read_block - perform smbus block read command
> + * @cyapa - private data structure of the driver
> + * @cmd - the properly encoded smbus command
> + * @len - expected length of smbus command result
> + * @values - buffer to store smbus command result
> + *
> + * Returns negative errno, else the number of bytes written.
> + *
> + * Note:
> + * In trackpad device, the memory block allocated for I2C register map
> + * is 256 bytes, so the max read block for I2C bus is 256 bytes.
> + */
> +ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len,
> + u8 *values)
> +{
> + ssize_t ret;
> + u8 index;
> + u8 smbus_cmd;
> + u8 *buf;
> + struct i2c_client *client = cyapa->client;
> +
> + if (!(SMBUS_BYTE_BLOCK_CMD_MASK & cmd))
> + return -EINVAL;
> +
> + if (SMBUS_GROUP_BLOCK_CMD_MASK & cmd) {
> + /* read specific block registers command. */
> + smbus_cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
> + ret = i2c_smbus_read_block_data(client, smbus_cmd, values);
> + goto out;
> + }
> +
> + ret = 0;
> + for (index = 0; index * I2C_SMBUS_BLOCK_MAX < len; index++) {
> + smbus_cmd = SMBUS_ENCODE_IDX(cmd, index);
> + smbus_cmd = SMBUS_ENCODE_RW(smbus_cmd, SMBUS_READ);
> + buf = values + I2C_SMBUS_BLOCK_MAX * index;
> + ret = i2c_smbus_read_block_data(client, smbus_cmd, buf);
> + if (ret < 0)
> + goto out;
> + }
> +
> +out:
> + return ret > 0 ? len : ret;
> +}
> +
> +s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx)
> +{
> + u8 cmd;
> +
> + if (cyapa->smbus) {
> + cmd = cyapa_smbus_cmds[cmd_idx].cmd;
> + cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
> + } else {
> + cmd = cyapa_i2c_cmds[cmd_idx].cmd;
> + }
> + return i2c_smbus_read_byte_data(cyapa->client, cmd);
> +}
> +
> +s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value)
> +{
> + u8 cmd;
> +
> + if (cyapa->smbus) {
> + cmd = cyapa_smbus_cmds[cmd_idx].cmd;
> + cmd = SMBUS_ENCODE_RW(cmd, SMBUS_WRITE);
> + } else {
> + cmd = cyapa_i2c_cmds[cmd_idx].cmd;
> + }
> + return i2c_smbus_write_byte_data(cyapa->client, cmd, value);
> +}
> +
> +ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values)
> +{
> + u8 cmd;
> + size_t len;
> +
> + if (cyapa->smbus) {
> + cmd = cyapa_smbus_cmds[cmd_idx].cmd;
> + len = cyapa_smbus_cmds[cmd_idx].len;
> + return cyapa_smbus_read_block(cyapa, cmd, len, values);
> + }
> + cmd = cyapa_i2c_cmds[cmd_idx].cmd;
> + len = cyapa_i2c_cmds[cmd_idx].len;
> + return cyapa_i2c_reg_read_block(cyapa, cmd, len, values);
> +}
> +
> +/*
> + * Determine the Gen3 trackpad device's current operating state.
> + *
> + */
> +static int cyapa_gen3_state_parse(struct cyapa *cyapa, u8 *reg_data, int len)
> +{
> + /*
> + * Must be in detecting and should not do data reporting.
> + * It will be reenabled when all detecting done and lauched into
> + * applicaiton mode successfully.
> + */
> + data_reporting_started = false;
> + cyapa->state = CYAPA_STATE_NO_DEVICE;
> +
> + /* Parse based on Gen3 characteristic registers and bits */
> + if (reg_data[REG_BL_FILE] == BL_FILE &&
> + reg_data[REG_BL_ERROR] == BL_ERROR_NO_ERR_IDLE &&
> + (reg_data[REG_BL_STATUS] ==
> + (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID) ||
> + reg_data[REG_BL_STATUS] == BL_STATUS_RUNNING)) {
> + /*
> + * Normal state after power on or reset,
> + * REG_BL_STATUS == 0x11, firmware image checksum is valid.
> + * REG_BL_STATUS == 0x10, firmware image checksum is invalid.
> + */
> + cyapa->gen = CYAPA_GEN3;
> + cyapa->state = CYAPA_STATE_BL_IDLE;
> + } else if (reg_data[REG_BL_FILE] == BL_FILE &&
> + (reg_data[REG_BL_STATUS] & BL_STATUS_RUNNING) ==
> + BL_STATUS_RUNNING) {
> + cyapa->gen = CYAPA_GEN3;
> + if (reg_data[REG_BL_STATUS] & BL_STATUS_BUSY) {
> + cyapa->state = CYAPA_STATE_BL_BUSY;
> + } else {
> + if ((reg_data[REG_BL_ERROR] & BL_ERROR_BOOTLOADING) ==
> + BL_ERROR_BOOTLOADING)
> + cyapa->state = CYAPA_STATE_BL_ACTIVE;
> + else
> + cyapa->state = CYAPA_STATE_BL_IDLE;
> + }
> + } else if ((reg_data[REG_OP_STATUS] & OP_STATUS_SRC) &&
> + (reg_data[REG_OP_DATA1] & OP_DATA_VALID)) {
> + /*
> + * Normal state when running in operaitonal mode,
> + * may also not in full power state or
> + * busying in command process.
> + */
> + if (GEN3_FINGER_NUM(reg_data[REG_OP_DATA1]) <=
> + GEN3_MAX_FINGERS) {
> + /* Finger number data is valid. */
> + cyapa->gen = CYAPA_GEN3;
> + cyapa->state = CYAPA_STATE_OP;
> + }
> + } else if (reg_data[REG_OP_STATUS] == 0x0C &&
> + reg_data[REG_OP_DATA1] == 0x08) {
> + /* Op state when first two registers overwritten with 0x00 */
> + cyapa->gen = CYAPA_GEN3;
> + cyapa->state = CYAPA_STATE_OP;
> + } else if (reg_data[REG_BL_STATUS] &
> + (BL_STATUS_RUNNING | BL_STATUS_BUSY)) {
> + cyapa->gen = CYAPA_GEN3;
> + cyapa->state = CYAPA_STATE_BL_BUSY;
> + }
> +
> + if (cyapa->gen == CYAPA_GEN3 && (cyapa->state == CYAPA_STATE_OP ||
> + cyapa->state == CYAPA_STATE_BL_IDLE ||
> + cyapa->state == CYAPA_STATE_BL_ACTIVE ||
> + cyapa->state == CYAPA_STATE_BL_BUSY))
> + return 0;
> +
> + return -EAGAIN;
> +}
> +
> +static int cyapa_gen3_bl_deactivate(struct cyapa *cyapa)
> +{
> + int ret;
> +
> + ret = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
> + bl_deactivate);
> + if (ret < 0)
> + return ret;
> +
> + /* Wait for bootloader to switch to idle state; should take < 100ms */
> + msleep(100);
> + ret = cyapa_poll_state(cyapa, 500);
> + if (ret < 0)
> + return ret;
> + if (cyapa->state != CYAPA_STATE_BL_IDLE)
> + return -EAGAIN;
> + return 0;
> +}
> +
> +/*
> + * Exit bootloader
> + *
> + * Send bl_exit command, then wait 50 - 100 ms to let device transition to
> + * operational mode. If this is the first time the device's firmware is
> + * running, it can take up to 2 seconds to calibrate its sensors. So, poll
> + * the device's new state for up to 2 seconds.
> + *
> + * Returns:
> + * -EIO failure while reading from device
> + * -EAGAIN device is stuck in bootloader, b/c it has invalid firmware
> + * 0 device is supported and in operational mode
> + */
> +static int cyapa_gen3_bl_exit(struct cyapa *cyapa)
> +{
> + int ret;
> +
> + ret = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * Wait for bootloader to exit, and operation mode to start.
> + * Normally, this takes at least 50 ms.
> + */
> + usleep_range(50000, 100000);
> + /*
> + * In addition, when a device boots for the first time after being
> + * updated to new firmware, it must first calibrate its sensors, which
> + * can take up to an additional 2 seconds. If the device power is
> + * running low, this may take even longer.
> + */
> + ret = cyapa_poll_state(cyapa, 4000);
> + if (ret < 0)
> + return ret;
> + if (cyapa->state != CYAPA_STATE_OP)
> + return -EAGAIN;
> +
> + return 0;
> +}
> +
> +/*
> + * cyapa_get_wait_time_for_pwr_cmd
> + *
> + * Compute the amount of time we need to wait after updating the touchpad
> + * power mode. The touchpad needs to consume the incoming power mode set
> + * command at the current clock rate.
> + */
> +
> +static u16 cyapa_get_wait_time_for_pwr_cmd(u8 pwr_mode)
> +{
> + switch (pwr_mode) {
> + case PWR_MODE_FULL_ACTIVE: return 20;
> + case PWR_MODE_BTN_ONLY: return 20;
> + case PWR_MODE_OFF: return 20;
> + default: return cyapa_pwr_cmd_to_sleep_time(pwr_mode) + 50;
> + }
> +}
> +
> +/*
> + * Set device power mode
> + *
> + * Write to the field to configure power state. Power states include :
> + * Full : Max scans and report rate.
> + * Idle : Report rate set by user specified time.
> + * ButtonOnly : No scans for fingers. When the button is triggered,
> + * a slave interrupt is asserted to notify host to wake up.
> + * Off : Only awake for i2c commands from host. No function for button
> + * or touch sensors.
> + *
> + * The power_mode command should conform to the following :
> + * Full : 0x3f
> + * Idle : Configurable from 20 to 1000ms. See note below for
> + * cyapa_sleep_time_to_pwr_cmd and cyapa_pwr_cmd_to_sleep_time
> + * ButtonOnly : 0x01
> + * Off : 0x00
> + *
> + * Device power mode can only be set when device is in operational mode.
> + */
> +static int cyapa_gen3_set_power_mode(struct cyapa *cyapa, u8 power_mode,
> + u16 always_unused)
> +{
> + int ret;
> + u8 power;
> + int tries = SET_POWER_MODE_TRIES;
> + u16 sleep_time;
> +
> + always_unused = 0;
> + if (cyapa->state != CYAPA_STATE_OP)
> + return 0;
> +
> + while (true) {
> + ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE);
> + if (ret >= 0 || --tries < 1)
> + break;
> + usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
> + }
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * Return early if the power mode to set is the same as the current
> + * one.
> + */
> + if ((ret & PWR_MODE_MASK) == power_mode)
> + return 0;
> +
> + sleep_time = cyapa_get_wait_time_for_pwr_cmd(ret & PWR_MODE_MASK);
> + power = ret;
> + power &= ~PWR_MODE_MASK;
> + power |= power_mode & PWR_MODE_MASK;
> + while (true) {
> + ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power);
> + if (!ret || --tries < 1)
> + break;
> + usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
> + }
> +
> + /*
> + * Wait for the newly set power command to go in at the previous
> + * clock speed (scanrate) used by the touchpad firmware. Not
> + * doing so before issuing the next command may result in errors
> + * depending on the command's content.
> + */
> + msleep(sleep_time);
> + return ret;
> +}
> +
> +static int cyapa_gen3_get_query_data(struct cyapa *cyapa)
> +{
> + u8 query_data[QUERY_DATA_SIZE];
> + int ret;
> +
> + if (cyapa->state != CYAPA_STATE_OP)
> + return -EBUSY;
> +
> + ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data);
> + if (ret != QUERY_DATA_SIZE)
> + return (ret < 0) ? ret : -EIO;
> +
> + memcpy(&cyapa->product_id[0], &query_data[0], 5);
> + cyapa->product_id[5] = '-';
> + memcpy(&cyapa->product_id[6], &query_data[5], 6);
> + cyapa->product_id[12] = '-';
> + memcpy(&cyapa->product_id[13], &query_data[11], 2);
> + cyapa->product_id[15] = '\0';
> +
> + cyapa->fw_maj_ver = query_data[15];
> + cyapa->fw_min_ver = query_data[16];
> +
> + cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK;
> +
> + cyapa->gen = query_data[20] & 0x0f;
> +
> + cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22];
> + cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23];
> +
> + cyapa->physical_size_x =
> + ((query_data[24] & 0xf0) << 4) | query_data[25];
> + cyapa->physical_size_y =
> + ((query_data[24] & 0x0f) << 8) | query_data[26];
> +
> + cyapa->max_z = 255;
> +
> + return 0;
> +}
> +
> +static int cyapa_gen3_bl_query_data(struct cyapa *cyapa)
> +{
> + u8 bl_data[CYAPA_CMD_LEN];
> + int ret;
> +
> + ret = cyapa_i2c_reg_read_block(cyapa, 0, CYAPA_CMD_LEN, bl_data);
> + if (ret != CYAPA_CMD_LEN)
> + return (ret < 0) ? ret : -EIO;
> +
> + /*
> + * This value will be updated again when entered application mode.
> + * If TP failed to enter application mode, this fw version values
> + * can be used as a reference.
> + * This firmware version valid when fw image checksum is valid.
> + */
> + if (bl_data[REG_BL_STATUS] ==
> + (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID)) {
> + cyapa->fw_maj_ver = bl_data[GEN3_BL_IDLE_FW_MAJ_VER_OFFSET];
> + cyapa->fw_min_ver = bl_data[GEN3_BL_IDLE_FW_MIN_VER_OFFSET];
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * Check if device is operational.
> + *
> + * An operational device is responding, has exited bootloader, and has
> + * firmware supported by this driver.
> + *
> + * Returns:
> + * -EBUSY no device or in bootloader
> + * -EIO failure while reading from device
> + * -EAGAIN device is still in bootloader
> + * if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware
> + * -EINVAL device is in operational mode, but not supported by this driver
> + * 0 device is supported
> + */
> +static int cyapa_gen3_do_operational_check(struct cyapa *cyapa)
> +{
> + struct device *dev = &cyapa->client->dev;
> + int ret;
> +
> + switch (cyapa->state) {
> + case CYAPA_STATE_BL_ACTIVE:
> + ret = cyapa_gen3_bl_deactivate(cyapa);
> + if (ret) {
> + dev_err(dev, "failed to bl_deactivate. %d\n", ret);
> + return ret;
> + }
> +
> + /* Fallthrough state */
> + case CYAPA_STATE_BL_IDLE:
> + /* Try to get firmware version in bootloader mode. */
> + cyapa_gen3_bl_query_data(cyapa);
> +
> + ret = cyapa_gen3_bl_exit(cyapa);
> + if (ret) {
> + dev_err(dev, "failed to bl_exit. %d\n", ret);
> + return ret;
> + }
> +
> + /* Fallthrough state */
> + case CYAPA_STATE_OP:
> + /*
> + * Reading query data before going back to the full mode
> + * may cause problems, so we set the power mode first here.
> + */
> + ret = cyapa_gen3_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE, 0);
> + if (ret)
> + dev_err(dev, "%s: set full power mode failed, (%d)\n",
> + __func__, ret);
> + ret = cyapa_gen3_get_query_data(cyapa);
> + if (ret < 0)
> + return ret;
> +
> + /* Only support firmware protocol gen3 */
> + if (cyapa->gen != CYAPA_GEN3) {
> + dev_err(dev, "unsupported protocol version (%d)",
> + cyapa->gen);
> + return -EINVAL;
> + }
> +
> + /* Only support product ID starting with CYTRA */
> + if (memcmp(cyapa->product_id, unique_str,
> + strlen(unique_str)) != 0) {
> + dev_err(dev, "unsupported product ID (%s)\n",
> + cyapa->product_id);
> + return -EINVAL;
> + }
> +
> + data_reporting_started = true;
> + return 0;
> +
> + default:
> + return -EIO;
> + }
> + return 0;
> +}
> +
> +/*
> + * Return false, do not continue process
> + * Return true, continue process.
> + */
> +static bool cyapa_gen3_irq_cmd_handler(struct cyapa *cyapa)
> +{
> + /* Not gen3 irq command response, skip for continue. */
> + if (cyapa->gen != CYAPA_GEN3)
> + return true;
> +
> + if (cyapa->input && data_reporting_started)
> + return true;
> +
> + /*
> + * Driver in detecting or other interface function processing,
> + * so, stop cyapa_gen3_irq_handler to continue process to
> + * avoid unwanted to error detecting and processing.
> + *
> + * And also, avoid the periodicly accerted interrupts to be processed
> + * as touch inputs when gen3 failed to launch into application mode,
> + * which will cause gen3 stays in bootloader mode.
> + */
> + return false;
> +}
> +
> +static int cyapa_gen3_irq_handler(struct cyapa *cyapa)
> +{
> + struct input_dev *input = cyapa->input;
> + struct device *dev = &cyapa->client->dev;
> + struct cyapa_reg_data data;
> + int i;
> + int ret;
> + int num_fingers;
> +
> + ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data);
> + if (ret != sizeof(data)) {
> + dev_err(dev, "failed to read report data, (%d)\n", ret);
> + return -EINVAL;
> + }
> +
> + if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC ||
> + (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL ||
> + (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) {
> + dev_err(dev, "invalid device state bytes, %02x %02x\n",
> + data.device_status, data.finger_btn);
> + return -EINVAL;
> + }
> +
> + num_fingers = (data.finger_btn >> 4) & 0x0f;
> + for (i = 0; i < num_fingers; i++) {
> + const struct cyapa_touch *touch = &data.touches[i];
> + /* Note: touch->id range is 1 to 15; slots are 0 to 14. */
> + int slot = touch->id - 1;
> +
> + input_mt_slot(input, slot);
> + input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
> + input_report_abs(input, ABS_MT_POSITION_X,
> + ((touch->xy_hi & 0xf0) << 4) | touch->x_lo);
> + input_report_abs(input, ABS_MT_POSITION_Y,
> + ((touch->xy_hi & 0x0f) << 8) | touch->y_lo);
> + input_report_abs(input, ABS_MT_PRESSURE, touch->pressure);
> + }
> +
> + input_mt_sync_frame(input);
> +
> + if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK)
> + input_report_key(input, BTN_LEFT,
> + !!(data.finger_btn & OP_DATA_LEFT_BTN));
> + if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK)
> + input_report_key(input, BTN_MIDDLE,
> + !!(data.finger_btn & OP_DATA_MIDDLE_BTN));
> + if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK)
> + input_report_key(input, BTN_RIGHT,
> + !!(data.finger_btn & OP_DATA_RIGHT_BTN));
> + input_sync(input);
> +
> + return 0;
> +}
> +
> +const struct cyapa_dev_ops cyapa_gen3_ops = {
> + .state_parse = cyapa_gen3_state_parse,
> + .operational_check = cyapa_gen3_do_operational_check,
> +
> + .irq_handler = cyapa_gen3_irq_handler,
> + .irq_cmd_handler = cyapa_gen3_irq_cmd_handler,
> +
> + .set_power_mode = cyapa_gen3_set_power_mode,
> +};
> --
> 1.9.1
>
--
Dmitry
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists