| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5470685C.8050104@kernel.org>
Date: Sat, 22 Nov 2014 10:41:32 +0000
From: Jonathan Cameron <jic23@...nel.org>
To: Daniel Baluta <daniel.baluta@...el.com>
CC: "linux-iio@...r.kernel.org" <linux-iio@...r.kernel.org>,
Srinivas Pandruvada <srinivas.pandruvada@...ux.intel.com>,
Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v2] iio: imu: Add support for Kionix KMX61 sensor
On 17/11/14 12:12, Daniel Baluta wrote:
> On Sun, Nov 16, 2014 at 11:10 PM, Jonathan Cameron <jic23@...nel.org> wrote:
>> On 10/11/14 17:24, Daniel Baluta wrote:
>>> Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
>>> raw accel/magn readings together with scale and sampling frequency.
>>>
>>> Datasheet will be available at:
>>> http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61
>>>
>>> Signed-off-by: Daniel Baluta <daniel.baluta@...el.com>
>> Looking very nice. I made a few more comments inline but only
>> one was more than a comment - I added a check on val==0 in the obvious
>> place. Please take a look at the testing branch of iio.git to make
>> sure I didn't mess anything up!
>
> Thanks! It looks good.
Dropped this version as discussed. Will take a look at V3 in a few mins.
>
>>
>> Applied to the togreg branch of iio.git - initially pushed out as testing
>> for the autobuilders to play with it.
>>
>> Jonathan
>>> ---
>>> Changes since v1:
>>> * serialize non-atomic operations with a mutex (set_odr/get_odr, set_scale).
>>> * no need to protect reading info scale because it reduces to reading an u8
>>> which should be atomic on all arches
>>> * *note* - read_measurment is an atomic operation
>>>
>>> drivers/iio/imu/Kconfig | 9 +
>>> drivers/iio/imu/Makefile | 2 +
>>> drivers/iio/imu/kmx61.c | 590 +++++++++++++++++++++++++++++++++++++++++++++++
>>> 3 files changed, 601 insertions(+)
>>> create mode 100644 drivers/iio/imu/kmx61.c
>>>
>>> diff --git a/drivers/iio/imu/Kconfig b/drivers/iio/imu/Kconfig
>>> index 2b0e451..d675f43 100644
>>> --- a/drivers/iio/imu/Kconfig
>>> +++ b/drivers/iio/imu/Kconfig
>>> @@ -25,6 +25,15 @@ config ADIS16480
>>> Say yes here to build support for Analog Devices ADIS16375, ADIS16480,
>>> ADIS16485, ADIS16488 inertial sensors.
>>>
>>> +config KMX61
>>> + tristate "Kionix KMX61 6-axis accelerometer and magnetometer"
>>> + depends on I2C
>>> + help
>>> + Say Y here if you want to build a driver for Kionix KMX61 6-axis accelerometer
>>> + and magnetometer.
>>> + To compile this driver as module, choose M here: the module will be called
>>> + kmx61.
>>> +
>>> source "drivers/iio/imu/inv_mpu6050/Kconfig"
>>>
>>> endmenu
>>> diff --git a/drivers/iio/imu/Makefile b/drivers/iio/imu/Makefile
>>> index 114d2c1..e1e6e3d 100644
>>> --- a/drivers/iio/imu/Makefile
>>> +++ b/drivers/iio/imu/Makefile
>>> @@ -14,3 +14,5 @@ adis_lib-$(CONFIG_IIO_ADIS_LIB_BUFFER) += adis_buffer.o
>>> obj-$(CONFIG_IIO_ADIS_LIB) += adis_lib.o
>>>
>>> obj-y += inv_mpu6050/
>>> +
>>> +obj-$(CONFIG_KMX61) += kmx61.o
>>> diff --git a/drivers/iio/imu/kmx61.c b/drivers/iio/imu/kmx61.c
>>> new file mode 100644
>>> index 0000000..6135a16
>>> --- /dev/null
>>> +++ b/drivers/iio/imu/kmx61.c
>>> @@ -0,0 +1,590 @@
>>> +/*
>>> + * KMX61 - Kionix 6-axis Accelerometer/Magnetometer
>>> + *
>>> + * Copyright (c) 2014, Intel Corporation.
>>> + *
>>> + * This file is subject to the terms and conditions of version 2 of
>>> + * the GNU General Public License. See the file COPYING in the main
>>> + * directory of this archive for more details.
>>> + *
>>> + * IIO driver for KMX61 (7-bit I2C slave address 0x0E or 0x0F).
>>> + *
>>> + * TODO: buffer, interrupt, thresholds, acpi, temperature sensor
>>> + *
>>> + */
>>> +
>>> +#include <linux/module.h>
>>> +#include <linux/i2c.h>
>>> +#include <linux/iio/iio.h>
>>> +#include <linux/iio/sysfs.h>
>>> +
>>> +#define KMX61_DRV_NAME "kmx61"
>>> +
>>> +#define KMX61_REG_WHO_AM_I 0x00
>>> +
>>> +#define KMX61_ACC_XOUT_L 0x0A
>>> +
>>> +#define KMX61_ACC_XOUT_H 0x0B
>>> +#define KMX61_ACC_YOUT_L 0x0C
>>> +#define KMX61_ACC_YOUT_H 0x0D
>>> +#define KMX61_ACC_ZOUT_L 0x0E
>>> +#define KMX61_ACC_ZOUT_H 0x0F
>>> +
>>> +#define KMX61_MAG_XOUT_L 0x12
>>> +
>>> +#define KMX61_MAG_XOUT_H 0x13
>>> +#define KMX61_MAG_YOUT_L 0x14
>>> +#define KMX61_MAG_YOUT_H 0x15
>>> +#define KMX61_MAG_ZOUT_L 0x16
>>> +#define KMX61_MAG_ZOUT_H 0x17
>>> +
>>> +#define KMX61_REG_ODCNTL 0x2C
>>> +
>>> +#define KMX61_REG_STBY 0x29
>>> +#define KMX61_REG_CTRL1 0x2A
>>> +
>>> +#define KMX61_REG_COTR 0x3C
>>> +
>>> +#define KMX61_ACC_STBY_BIT BIT(0)
>>> +#define KMX61_MAG_STBY_BIT BIT(1)
>>> +#define KMX61_ACT_STBY_BIT BIT(7)
>>> +
>>> +#define KMX61_ALL_STBY (KMX61_ACC_STBY_BIT | KMX61_MAG_STBY_BIT)
>>> +
>>> +#define KMX61_REG_CTRL1_GSEL0_SHIFT 0
>>> +#define KMX61_REG_CTRL1_GSEL1_SHIFT 1
>>> +#define KMX61_REG_CTRL1_GSEL0_MASK 0x01
>>> +#define KMX61_REG_CTRL1_GSEL1_MASK 0x02
>>> +
>>> +#define KMX61_REG_CTRL1_BIT_RES BIT(4)
>>> +
>>> +#define KMX61_ACC_ODR_SHIFT 0
>>> +#define KMX61_MAG_ODR_SHIFT 4
>>> +#define KMX61_ACC_ODR_MASK 0x0F
>>> +#define KMX61_MAG_ODR_MASK 0xF0
>>> +
>>> +#define KMX61_CHIP_ID 0x12
>>> +
>>> +struct kmx61_data {
>>> + struct i2c_client *client;
>>> + /* serialize access to non-atomic ops, e.g set_mode */
>>> + struct mutex lock;
>>> + u8 range;
>>> + u8 odr_bits;
>>> +};
>>> +
>>> +enum kmx61_range {
>>> + KMX61_RANGE_2G,
>>> + KMX61_RANGE_4G,
>>> + KMX61_RANGE_8G,
>>> +};
>>> +
>>> +enum kmx61_scan {
>>> + KMX61_SCAN_ACC_X,
>>> + KMX61_SCAN_ACC_Y,
>>> + KMX61_SCAN_ACC_Z,
>>> + KMX61_SCAN_TEMP,
>>> + KMX61_SCAN_MAG_X,
>>> + KMX61_SCAN_MAG_Y,
>>> + KMX61_SCAN_MAG_Z,
>>> +};
>>> +
>>> +static const struct {
>>> + u16 scale;
>>> + u8 gsel0;
>>> + u8 gsel1;
>>> +} kmx61_scale_table[] = {
>>> + {9582, 0, 0},
>>> + {19163, 1, 0},
>>> + {38326, 0, 1},
>>> +};
>>> +
>>> +/* KMX61 devices */
>>> +#define KMX61_ACC 0x01
>>> +#define KMX61_MAG 0x02
>>> +
>>> +static const struct {
>>> + int val;
>>> + int val2;
>>> + int odr_bits;
>>> +} samp_freq_table[] = { {12, 500000, 0x00},
>>> + {25, 0, 0x01},
>>> + {50, 0, 0x02},
>>> + {100, 0, 0x03},
>>> + {200, 0, 0x04},
>>> + {400, 0, 0x05},
>>> + {800, 0, 0x06},
>>> + {1600, 0, 0x07},
>>> + {0, 781000, 0x08},
>>> + {1, 563000, 0x09},
>>> + {3, 125000, 0x0A},
>>> + {6, 250000, 0x0B} };
>>> +
>>> +static IIO_CONST_ATTR(accel_scale_available, "0.009582 0.019163 0.038326");
>>> +static IIO_CONST_ATTR(magn_scale_available, "0.001465");
>>> +static IIO_CONST_ATTR_SAMP_FREQ_AVAIL(
>>> + "0.781000 1.563000 3.125000 6.250000 12.500000 25 50 100 200 400 800");
>>> +
>>> +static struct attribute *kmx61_attributes[] = {
>>> + &iio_const_attr_accel_scale_available.dev_attr.attr,
>>> + &iio_const_attr_magn_scale_available.dev_attr.attr,
>>> + &iio_const_attr_sampling_frequency_available.dev_attr.attr,
>> Interesting. So sampling frequency is controllable seperately for the
>> two sensing types, but uses a single set of values. This is a rare
>> coherent looking bit of dual sensor type hardware ;)
>
> Yes.
>
> Anyway, when the FIFO hardware buffer is used, it will be updated
> at the faster of the two output data rates
>
>>> + NULL,
>>> +};
>>> +
>>> +static const struct attribute_group kmx61_attribute_group = {
>>> + .attrs = kmx61_attributes,
>>> +};
>>> +
>>> +#define KMX61_ACC_CHAN(_axis, _index) { \
>>> + .type = IIO_ACCEL, \
>>> + .modified = 1, \
>>> + .channel2 = IIO_MOD_ ## _axis, \
>>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
>>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
>>> + BIT(IIO_CHAN_INFO_SAMP_FREQ), \
>>> + .scan_index = _index, \
>>> + .scan_type = { \
>>> + .sign = 's', \
>>> + .realbits = 12, \
>>> + .storagebits = 16, \
>>> + .shift = 4, \
>>> + .endianness = IIO_BE, \
>>> + }, \
>>> +}
>>> +
>>> +#define KMX61_MAG_CHAN(_axis, _index) { \
>>> + .type = IIO_MAGN, \
>>> + .modified = 1, \
>>> + .channel2 = IIO_MOD_ ## _axis, \
>>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
>>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
>>> + BIT(IIO_CHAN_INFO_SAMP_FREQ), \
>>> + .scan_index = _index, \
>>> + .scan_type = { \
>>> + .sign = 's', \
>>> + .realbits = 14, \
>>> + .storagebits = 16, \
>>> + .shift = 2, \
>>> + .endianness = IIO_BE, \
>>> + }, \
>> Wouldn't normally expect scan_index and scan_type in a driver
>> without buffered support, but you do make use of some of the
>> elements elsewhere and state that buffered support
>> is on the todo list so lets leave it here.
>>> +}
>>> +
>>> +static const struct iio_chan_spec kmx61_channels[] = {
>>> + KMX61_ACC_CHAN(X, KMX61_SCAN_ACC_X),
>>> + KMX61_ACC_CHAN(Y, KMX61_SCAN_ACC_Y),
>>> + KMX61_ACC_CHAN(Z, KMX61_SCAN_ACC_Z),
>>> + KMX61_MAG_CHAN(X, KMX61_SCAN_MAG_X),
>>> + KMX61_MAG_CHAN(Y, KMX61_SCAN_MAG_Y),
>>> + KMX61_MAG_CHAN(Z, KMX61_SCAN_MAG_Z),
>>> +};
>>> +
>>> +static int kmx61_convert_freq_to_bit(int val, int val2)
>>> +{
>>> + int i;
>>> +
>>> + for (i = 0; i < ARRAY_SIZE(samp_freq_table); i++)
>>> + if (val == samp_freq_table[i].val &&
>>> + val2 == samp_freq_table[i].val2)
>>> + return samp_freq_table[i].odr_bits;
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int kmx61_set_mode(struct kmx61_data *data, u8 mode, u8 device)
>>> +{
>>> + int ret;
>>> +
>>> + ret = i2c_smbus_read_byte_data(data->client, KMX61_REG_STBY);
>>> + if (ret < 0) {
>>> + dev_err(&data->client->dev, "Error reading reg_stby\n");
>>> + return ret;
>>> + }
>>> + if (device & KMX61_ACC) {
>>> + if (mode & KMX61_ACC_STBY_BIT)
>>> + ret |= KMX61_ACC_STBY_BIT;
>>> + else
>>> + ret &= ~KMX61_ACC_STBY_BIT;
>>> + }
>>> +
>>> + if (device & KMX61_MAG) {
>>> + if (mode & KMX61_MAG_STBY_BIT)
>>> + ret |= KMX61_MAG_STBY_BIT;
>>> + else
>>> + ret &= ~KMX61_MAG_STBY_BIT;
>>> + }
>>> +
>>> + ret = i2c_smbus_write_byte_data(data->client, KMX61_REG_STBY, ret);
>>> + if (ret < 0) {
>>> + dev_err(&data->client->dev, "Error writing reg_stby\n");
>>> + return ret;
>>> + }
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static int kmx61_get_mode(struct kmx61_data *data, u8 *mode, u8 device)
>>> +{
>>> + int ret;
>>> +
>>> + ret = i2c_smbus_read_byte_data(data->client, KMX61_REG_STBY);
>>> + if (ret < 0) {
>>> + dev_err(&data->client->dev, "Error reading reg_stby\n");
>>> + return ret;
>>> + }
>>> + *mode = 0;
>>> +
>>> + if (device & KMX61_ACC) {
>>> + if (ret & KMX61_ACC_STBY_BIT)
>>> + *mode |= KMX61_ACC_STBY_BIT;
>>> + else
>>> + *mode &= ~KMX61_ACC_STBY_BIT;
>>> + }
>>> +
>>> + if (device & KMX61_MAG) {
>>> + if (ret & KMX61_MAG_STBY_BIT)
>>> + *mode |= KMX61_MAG_STBY_BIT;
>>> + else
>>> + *mode &= ~KMX61_MAG_STBY_BIT;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int kmx61_set_odr(struct kmx61_data *data, int val, int val2, u8 device)
>>> +{
>>> + int ret;
>>> + u8 mode;
>>> + int lodr_bits, odr_bits;
>>> +
>>> + ret = kmx61_get_mode(data, &mode, KMX61_ACC | KMX61_MAG);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + lodr_bits = kmx61_convert_freq_to_bit(val, val2);
>>> + if (lodr_bits < 0)
>>> + return lodr_bits;
>>> +
>>> + /* To change ODR, accel and magn must be in STDBY */
>>> + ret = kmx61_set_mode(data, KMX61_ALL_STBY, KMX61_ACC | KMX61_MAG);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + odr_bits = 0;
>>> + if (device & KMX61_ACC)
>>> + odr_bits |= lodr_bits;
>>> + if (device & KMX61_MAG)
>>> + odr_bits |= (lodr_bits << KMX61_MAG_ODR_SHIFT);
>>> +
>>> + ret = i2c_smbus_write_byte_data(data->client, KMX61_REG_ODCNTL,
>>> + odr_bits);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + ret = kmx61_set_mode(data, mode, KMX61_ACC | KMX61_MAG);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + data->odr_bits = lodr_bits;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static
>>> +int kmx61_get_odr(struct kmx61_data *data, int *val, int *val2, u8 device)
>>> +{ int i;
>>> + u8 lodr_bits;
>>> +
>>> + if (device & KMX61_ACC)
>>> + lodr_bits = (data->odr_bits >> KMX61_ACC_ODR_SHIFT) &
>>> + KMX61_ACC_ODR_MASK;
>>> + else if (device & KMX61_MAG)
>>> + lodr_bits = (data->odr_bits >> KMX61_MAG_ODR_SHIFT) &
>>> + KMX61_MAG_ODR_MASK;
>>> + else
>>> + return -EINVAL;
>>> +
>>> + for (i = 0; i < ARRAY_SIZE(samp_freq_table); i++)
>>> + if (lodr_bits == samp_freq_table[i].odr_bits) {
>>> + *val = samp_freq_table[i].val;
>>> + *val2 = samp_freq_table[i].val2;
>>> + return 0;
>>> + }
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int kmx61_set_range(struct kmx61_data *data, int range)
>>> +{
>>> + int ret;
>>> +
>>> + ret = i2c_smbus_read_byte_data(data->client, KMX61_REG_CTRL1);
>>> + if (ret < 0) {
>>> + dev_err(&data->client->dev, "Error reading reg_ctrl1\n");
>>> + return ret;
>>> + }
>>> +
>>> + ret &= ~(KMX61_REG_CTRL1_GSEL0_MASK | KMX61_REG_CTRL1_GSEL1_MASK);
>>> + ret |= kmx61_scale_table[range].gsel0 << KMX61_REG_CTRL1_GSEL0_SHIFT;
>>> + ret |= kmx61_scale_table[range].gsel1 << KMX61_REG_CTRL1_GSEL1_SHIFT;
>>> +
>>> + ret = i2c_smbus_write_byte_data(data->client, KMX61_REG_CTRL1, ret);
>>> + if (ret < 0) {
>>> + dev_err(&data->client->dev, "Error writing reg_ctrl1\n");
>>> + return ret;
>>> + }
>>> +
>>> + data->range = range;
>>> +
>>> + return 0;
>>> +}
>>> +
>> I'd be tempted to use a parameter name other than val as that
>> tends to have a fairly specific meaning in iio drivers
>> (afterall you pass val2 in here!) scale would work or
>> maybe microscale or similar?
>
> 'scale' works for me. I will send a cleanup patch.
>
>>> +static int kmx61_set_scale(struct kmx61_data *data, int val)
>>> +{
>>> + int ret, i;
>>> + u8 mode;
>>> +
>>> + for (i = 0; i < ARRAY_SIZE(kmx61_scale_table); i++) {
>>> + if (kmx61_scale_table[i].scale == val) {
>>> + ret = kmx61_get_mode(data, &mode,
>>> + KMX61_ACC | KMX61_MAG);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + ret = kmx61_set_mode(data, KMX61_ALL_STBY,
>>> + KMX61_ACC | KMX61_MAG);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + ret = kmx61_set_range(data, i);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + ret = kmx61_set_mode(data, mode,
>>> + KMX61_ACC | KMX61_MAG);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + return 0;
>>> + }
>>> + }
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int kmx61_chip_init(struct kmx61_data *data)
>>> +{
>>> + int ret;
>>> +
>>> + ret = i2c_smbus_read_byte_data(data->client, KMX61_REG_WHO_AM_I);
>>> + if (ret < 0) {
>>> + dev_err(&data->client->dev, "Error reading who_am_i\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (ret != KMX61_CHIP_ID) {
>>> + dev_err(&data->client->dev,
>>> + "Wrong chip id, got %x expected %x\n",
>>> + ret, KMX61_CHIP_ID);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + /* set accel 12bit, 4g range */
>>> + ret = kmx61_set_range(data, KMX61_RANGE_4G);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + /* put accel and magnetometer in operating mode */
>>> + ret = kmx61_set_mode(data, 0, KMX61_ACC | KMX61_MAG);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int kmx61_read_measurement(struct kmx61_data *data, int base, int offset)
>>> +{
>>> + int ret;
>>> + u8 reg = base + offset * 2;
>>> +
>>> + ret = i2c_smbus_read_word_data(data->client, reg);
>>> + if (ret < 0) {
>>> + dev_err(&data->client->dev, "failed to read reg at %x\n", reg);
>>> + return ret;
>>> + }
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static int kmx61_read_raw(struct iio_dev *indio_dev,
>>> + struct iio_chan_spec const *chan, int *val,
>>> + int *val2, long mask)
>>> +{
>>> + struct kmx61_data *data = iio_priv(indio_dev);
>>> + int ret;
>>> + u8 base_reg;
>>> + u8 device;
>>> +
>>> + switch (mask) {
>>> + case IIO_CHAN_INFO_RAW:
>>> + switch (chan->type) {
>>> + case IIO_ACCEL: case IIO_MAGN:
>>> + base_reg = KMX61_ACC_XOUT_L;
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> + ret = kmx61_read_measurement(data, base_reg, chan->scan_index);
>>> + if (ret < 0)
>>> + return ret;
>>> + *val = sign_extend32(ret >> chan->scan_type.shift,
>>> + chan->scan_type.realbits - 1);
>>> + return IIO_VAL_INT;
>>> + case IIO_CHAN_INFO_SCALE:
>>> + switch (chan->type) {
>>> + case IIO_ACCEL:
>>> + *val = 0;
>>> + *val2 = kmx61_scale_table[data->range].scale;
>>> + return IIO_VAL_INT_PLUS_MICRO;
>>> + case IIO_MAGN:
>>> + /* 14 bits res, 1465 microGauss per magn count */
>>> + *val = 0;
>>> + *val2 = 1465;
>>> + return IIO_VAL_INT_PLUS_MICRO;
>>> + default:
>>> + break;
>>> + }
>>> + case IIO_CHAN_INFO_SAMP_FREQ:
>>> + switch (chan->type) {
>>> + case IIO_ACCEL:
>>> + device = KMX61_ACC;
>>> + break;
>>> + case IIO_MAGN:
>>> + device = KMX61_MAG;
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +
>>> + mutex_lock(&data->lock);
>>> + ret = kmx61_get_odr(data, val, val2, device);
>>> + mutex_unlock(&data->lock);
>>> + if (ret)
>>> + return -EINVAL;
>>> + return IIO_VAL_INT_PLUS_MICRO;
>>> + }
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int kmx61_write_raw(struct iio_dev *indio_dev,
>>> + struct iio_chan_spec const *chan, int val,
>>> + int val2, long mask)
>>> +{
>>> + struct kmx61_data *data = iio_priv(indio_dev);
>>> + int ret;
>>> + u8 device;
>>> +
>>> + switch (mask) {
>>> + case IIO_CHAN_INFO_SAMP_FREQ:
>>> + switch (chan->type) {
>>> + case IIO_ACCEL:
>>> + device = KMX61_ACC;
>>> + break;
>>> + case IIO_MAGN:
>>> + device = KMX61_MAG;
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> + mutex_lock(&data->lock);
>>> + ret = kmx61_set_odr(data, val, val2, device);
>>> + mutex_unlock(&data->lock);
>>> + break;
>>> + case IIO_CHAN_INFO_SCALE:
>>> + switch (chan->type) {
>>> + case IIO_ACCEL:
>>
>> Should verify that val == 0 incase of crazy userspace input.
>
> Looks good. Thanks for updating the patch.
>
>>> + mutex_lock(&data->lock);
>>> + ret = kmx61_set_scale(data, val2);
>>> + mutex_unlock(&data->lock);
>>> + break;
>>> + default:
>>> + ret = -EINVAL;
>>> + }
>>> + break;
>>> + default:
>>> + ret = -EINVAL;
>>> + }
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static const struct iio_info kmx61_info = {
>>> + .driver_module = THIS_MODULE,
>>> + .read_raw = kmx61_read_raw,
>>> + .write_raw = kmx61_write_raw,
>>> + .attrs = &kmx61_attribute_group,
>>> +};
>>> +
>>> +static int kmx61_probe(struct i2c_client *client,
>>> + const struct i2c_device_id *id)
>>> +{
>>> + struct kmx61_data *data;
>>> + struct iio_dev *indio_dev;
>>> + int ret;
>>> +
>>> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
>>> + if (!indio_dev)
>>> + return -ENOMEM;
>>> +
>>> + data = iio_priv(indio_dev);
>>> + i2c_set_clientdata(client, indio_dev);
>>> + data->client = client;
>>> +
>>> + indio_dev->dev.parent = &client->dev;
>>> + indio_dev->info = &kmx61_info;
>>> + indio_dev->channels = kmx61_channels;
>>> + indio_dev->num_channels = ARRAY_SIZE(kmx61_channels);
>>> + indio_dev->modes = INDIO_DIRECT_MODE;
>>> +
>>> + mutex_init(&data->lock);
>>> +
>>> + ret = kmx61_chip_init(data);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + return iio_device_register(indio_dev);
>>> +}
>>> +
>>> +static int kmx61_remove(struct i2c_client *client)
>>> +{
>>> + struct iio_dev *indio_dev = i2c_get_clientdata(client);
>>> + struct kmx61_data *data = iio_priv(indio_dev);
>>> + int ret;
>>> +
>>> + iio_device_unregister(indio_dev);
>>> +
>>> + mutex_lock(&data->lock);
>>> + ret = kmx61_set_mode(data, KMX61_ALL_STBY, KMX61_ACC | KMX61_MAG);
>>> + mutex_unlock(&data->lock);
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static const struct i2c_device_id kmx61_id[] = {
>>> + {"kmx61", 0},
>>> + {}
>>> +};
>>> +
>>> +MODULE_DEVICE_TABLE(i2c, kmx61_id);
>>> +
>>> +static struct i2c_driver kmx61_driver = {
>>> + .driver = {
>>> + .name = "kmx61",
>>> + },
>>> + .probe = kmx61_probe,
>>> + .remove = kmx61_remove,
>>> + .id_table = kmx61_id,
>>> +};
>>> +
>>> +module_i2c_driver(kmx61_driver);
>>> +
>>> +MODULE_AUTHOR("Daniel Baluta <daniel.baluta@...el.com>");
>>> +MODULE_DESCRIPTION("KMX61 accelerometer/magnetometer driver");
>>> +MODULE_LICENSE("GPL v2");
>>>
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
>> the body of a message to majordomo@...r.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@...r.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists