| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5475E2AE.6010905@ti.com>
Date: Wed, 26 Nov 2014 19:54:46 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>
CC: Antoine Tenart <antoine.tenart@...e-electrons.com>,
Grant Likely <grant.likely@...aro.org>,
Rob Herring <robh+dt@...nel.org>, <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 1/2] phy: add the Berlin USB PHY driver
On Wednesday 26 November 2014 07:13 PM, Sebastian Hesselbarth wrote:
> On 11/20/2014 10:53 PM, Sebastian Hesselbarth wrote:
>> From: Antoine Tenart <antoine.tenart@...e-electrons.com>
>>
>> Add the driver driving the Marvell Berlin USB PHY. This allows to
>> initialize the PHY and to use it from the USB driver later.
>>
>> Signed-off-by: Antoine Tenart <antoine.tenart@...e-electrons.com>
>
> Gentle ping.
>
> Kishon, anything wrong with these two patches?
It's already queued in linux-phy next.
Thanks
Kishon
>
> Sebastian
>
>> ---
>> Split-off patches from latest Berlin USB PHY patches
>>
>> https://lkml.kernel.org/g/1416231347-27193-1-git-send-email-antoine.tenart@free-electrons.com
>>
>>
>> Cc: Kishon Vijay Abraham I <kishon@...com>
>> Cc: Grant Likely <grant.likely@...aro.org>
>> Cc: Rob Herring <robh+dt@...nel.org>
>> Cc: Antoine Tenart <antoine.tenart@...e-electrons.com>
>> Cc: devicetree@...r.kernel.org
>> Cc: linux-arm-kernel@...ts.infradead.org
>> Cc: linux-kernel@...r.kernel.org
>> ---
>> drivers/phy/Kconfig | 7 ++
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-berlin-usb.c | 224 ++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 232 insertions(+), 0 deletions(-)
>> create mode 100644 drivers/phy/phy-berlin-usb.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 2a436e6..38ca6ff 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -15,6 +15,13 @@ config GENERIC_PHY
>> phy users can obtain reference to the PHY. All the users of this
>> framework should select this config.
>>
>> +config PHY_BERLIN_USB
>> + tristate "Marvell Berlin USB PHY Driver"
>> + depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
>> + select GENERIC_PHY
>> + help
>> + Enable this to support the USB PHY on Marvell Berlin SoCs.
>> +
>> config PHY_BERLIN_SATA
>> tristate "Marvell Berlin SATA PHY driver"
>> depends on ARCH_BERLIN && HAS_IOMEM && OF
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index c4590fc..6fd1f77 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -3,6 +3,7 @@
>> #
>>
>> obj-$(CONFIG_GENERIC_PHY) += phy-core.o
>> +obj-$(CONFIG_PHY_BERLIN_USB) += phy-berlin-usb.o
>> obj-$(CONFIG_PHY_BERLIN_SATA) += phy-berlin-sata.o
>> obj-$(CONFIG_BCM_KONA_USB2_PHY) += phy-bcm-kona-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
>> diff --git a/drivers/phy/phy-berlin-usb.c b/drivers/phy/phy-berlin-usb.c
>> new file mode 100644
>> index 0000000..f9f1306
>> --- /dev/null
>> +++ b/drivers/phy/phy-berlin-usb.c
>> @@ -0,0 +1,224 @@
>> +/*
>> + * Copyright (C) 2014 Marvell Technology Group Ltd.
>> + *
>> + * Antoine Tenart <antoine.tenart@...e-electrons.com>
>> + * Jisheng Zhang <jszhang@...vell.com>
>> + *
>> + * This file is licensed under the terms of the GNU General Public
>> + * License version 2. This program is licensed "as is" without any
>> + * warranty of any kind, whether express or implied.
>> + */
>> +
>> +#include <linux/gpio.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of_gpio.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/reset.h>
>> +
>> +#define USB_PHY_PLL 0x04
>> +#define USB_PHY_PLL_CONTROL 0x08
>> +#define USB_PHY_TX_CTRL0 0x10
>> +#define USB_PHY_TX_CTRL1 0x14
>> +#define USB_PHY_TX_CTRL2 0x18
>> +#define USB_PHY_RX_CTRL 0x20
>> +#define USB_PHY_ANALOG 0x34
>> +
>> +/* USB_PHY_PLL */
>> +#define CLK_REF_DIV(x) ((x) << 4)
>> +#define FEEDBACK_CLK_DIV(x) ((x) << 8)
>> +
>> +/* USB_PHY_PLL_CONTROL */
>> +#define CLK_STABLE BIT(0)
>> +#define PLL_CTRL_PIN BIT(1)
>> +#define PLL_CTRL_REG BIT(2)
>> +#define PLL_ON BIT(3)
>> +#define PHASE_OFF_TOL_125 (0x0 << 5)
>> +#define PHASE_OFF_TOL_250 BIT(5)
>> +#define KVC0_CALIB (0x0 << 9)
>> +#define KVC0_REG_CTRL BIT(9)
>> +#define KVC0_HIGH (0x0 << 10)
>> +#define KVC0_LOW (0x3 << 10)
>> +#define CLK_BLK_EN BIT(13)
>> +
>> +/* USB_PHY_TX_CTRL0 */
>> +#define EXT_HS_RCAL_EN BIT(3)
>> +#define EXT_FS_RCAL_EN BIT(4)
>> +#define IMPCAL_VTH_DIV(x) ((x) << 5)
>> +#define EXT_RS_RCAL_DIV(x) ((x) << 8)
>> +#define EXT_FS_RCAL_DIV(x) ((x) << 12)
>> +
>> +/* USB_PHY_TX_CTRL1 */
>> +#define TX_VDD15_14 (0x0 << 4)
>> +#define TX_VDD15_15 BIT(4)
>> +#define TX_VDD15_16 (0x2 << 4)
>> +#define TX_VDD15_17 (0x3 << 4)
>> +#define TX_VDD12_VDD (0x0 << 6)
>> +#define TX_VDD12_11 BIT(6)
>> +#define TX_VDD12_12 (0x2 << 6)
>> +#define TX_VDD12_13 (0x3 << 6)
>> +#define LOW_VDD_EN BIT(8)
>> +#define TX_OUT_AMP(x) ((x) << 9)
>> +
>> +/* USB_PHY_TX_CTRL2 */
>> +#define TX_CHAN_CTRL_REG(x) ((x) << 0)
>> +#define DRV_SLEWRATE(x) ((x) << 4)
>> +#define IMP_CAL_FS_HS_DLY_0 (0x0 << 6)
>> +#define IMP_CAL_FS_HS_DLY_1 BIT(6)
>> +#define IMP_CAL_FS_HS_DLY_2 (0x2 << 6)
>> +#define IMP_CAL_FS_HS_DLY_3 (0x3 << 6)
>> +#define FS_DRV_EN_MASK(x) ((x) << 8)
>> +#define HS_DRV_EN_MASK(x) ((x) << 12)
>> +
>> +/* USB_PHY_RX_CTRL */
>> +#define PHASE_FREEZE_DLY_2_CL (0x0 << 0)
>> +#define PHASE_FREEZE_DLY_4_CL BIT(0)
>> +#define ACK_LENGTH_8_CL (0x0 << 2)
>> +#define ACK_LENGTH_12_CL BIT(2)
>> +#define ACK_LENGTH_16_CL (0x2 << 2)
>> +#define ACK_LENGTH_20_CL (0x3 << 2)
>> +#define SQ_LENGTH_3 (0x0 << 4)
>> +#define SQ_LENGTH_6 BIT(4)
>> +#define SQ_LENGTH_9 (0x2 << 4)
>> +#define SQ_LENGTH_12 (0x3 << 4)
>> +#define DISCON_THRESHOLD_260 (0x0 << 6)
>> +#define DISCON_THRESHOLD_270 BIT(6)
>> +#define DISCON_THRESHOLD_280 (0x2 << 6)
>> +#define DISCON_THRESHOLD_290 (0x3 << 6)
>> +#define SQ_THRESHOLD(x) ((x) << 8)
>> +#define LPF_COEF(x) ((x) << 12)
>> +#define INTPL_CUR_10 (0x0 << 14)
>> +#define INTPL_CUR_20 BIT(14)
>> +#define INTPL_CUR_30 (0x2 << 14)
>> +#define INTPL_CUR_40 (0x3 << 14)
>> +
>> +/* USB_PHY_ANALOG */
>> +#define ANA_PWR_UP BIT(1)
>> +#define ANA_PWR_DOWN BIT(2)
>> +#define V2I_VCO_RATIO(x) ((x) << 7)
>> +#define R_ROTATE_90 (0x0 << 10)
>> +#define R_ROTATE_0 BIT(10)
>> +#define MODE_TEST_EN BIT(11)
>> +#define ANA_TEST_DC_CTRL(x) ((x) << 12)
>> +
>> +#define to_phy_berlin_usb_priv(p) \
>> + container_of((p), struct phy_berlin_usb_priv, phy)
>> +
>> +static const u32 phy_berlin_pll_dividers[] = {
>> + /* Berlin 2 */
>> + CLK_REF_DIV(0xc) | FEEDBACK_CLK_DIV(0x54),
>> + /* Berlin 2CD */
>> + CLK_REF_DIV(0x6) | FEEDBACK_CLK_DIV(0x55),
>> +};
>> +
>> +struct phy_berlin_usb_priv {
>> + void __iomem *base;
>> + struct phy *phy;
>> + struct reset_control *rst_ctrl;
>> + u32 pll_divider;
>> +};
>> +
>> +static int phy_berlin_usb_power_on(struct phy *phy)
>> +{
>> + struct phy_berlin_usb_priv *priv = dev_get_drvdata(phy->dev.parent);
>> +
>> + reset_control_reset(priv->rst_ctrl);
>> +
>> + writel(priv->pll_divider,
>> + priv->base + USB_PHY_PLL);
>> + writel(CLK_STABLE | PLL_CTRL_REG | PHASE_OFF_TOL_250 | KVC0_REG_CTRL |
>> + CLK_BLK_EN, priv->base + USB_PHY_PLL_CONTROL);
>> + writel(V2I_VCO_RATIO(0x5) | R_ROTATE_0 | ANA_TEST_DC_CTRL(0x5),
>> + priv->base + USB_PHY_ANALOG);
>> + writel(PHASE_FREEZE_DLY_4_CL | ACK_LENGTH_16_CL | SQ_LENGTH_12 |
>> + DISCON_THRESHOLD_260 | SQ_THRESHOLD(0xa) | LPF_COEF(0x2) |
>> + INTPL_CUR_30, priv->base + USB_PHY_RX_CTRL);
>> +
>> + writel(TX_VDD12_13 | TX_OUT_AMP(0x3), priv->base + USB_PHY_TX_CTRL1);
>> + writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4),
>> + priv->base + USB_PHY_TX_CTRL0);
>> +
>> + writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4) |
>> + EXT_FS_RCAL_DIV(0x2), priv->base + USB_PHY_TX_CTRL0);
>> +
>> + writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4),
>> + priv->base + USB_PHY_TX_CTRL0);
>> + writel(TX_CHAN_CTRL_REG(0xf) | DRV_SLEWRATE(0x3) | IMP_CAL_FS_HS_DLY_3 |
>> + FS_DRV_EN_MASK(0xd), priv->base + USB_PHY_TX_CTRL2);
>> +
>> + return 0;
>> +}
>> +
>> +static struct phy_ops phy_berlin_usb_ops = {
>> + .power_on = phy_berlin_usb_power_on,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static const struct of_device_id phy_berlin_sata_of_match[] = {
>> + {
>> + .compatible = "marvell,berlin2-usb-phy",
>> + .data = &phy_berlin_pll_dividers[0],
>> + },
>> + {
>> + .compatible = "marvell,berlin2cd-usb-phy",
>> + .data = &phy_berlin_pll_dividers[1],
>> + },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, phy_berlin_sata_of_match);
>> +
>> +static int phy_berlin_usb_probe(struct platform_device *pdev)
>> +{
>> + const struct of_device_id *match =
>> + of_match_device(phy_berlin_sata_of_match, &pdev->dev);
>> + struct phy_berlin_usb_priv *priv;
>> + struct resource *res;
>> + struct phy_provider *phy_provider;
>> +
>> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
>> + if (!priv)
>> + return -ENOMEM;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + priv->base = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(priv->base))
>> + return PTR_ERR(priv->base);
>> +
>> + priv->rst_ctrl = devm_reset_control_get(&pdev->dev, NULL);
>> + if (IS_ERR(priv->rst_ctrl))
>> + return PTR_ERR(priv->rst_ctrl);
>> +
>> + priv->pll_divider = *((u32 *)match->data);
>> +
>> + priv->phy = devm_phy_create(&pdev->dev, NULL, &phy_berlin_usb_ops,
>> + NULL);
>> + if (IS_ERR(priv->phy)) {
>> + dev_err(&pdev->dev, "failed to create PHY\n");
>> + return PTR_ERR(priv->phy);
>> + }
>> +
>> + platform_set_drvdata(pdev, priv);
>> +
>> + phy_provider =
>> + devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
>> + if (IS_ERR(phy_provider))
>> + return PTR_ERR(phy_provider);
>> +
>> + return 0;
>> +}
>> +
>> +static struct platform_driver phy_berlin_usb_driver = {
>> + .probe = phy_berlin_usb_probe,
>> + .driver = {
>> + .name = "phy-berlin-usb",
>> + .owner = THIS_MODULE,
>> + .of_match_table = phy_berlin_sata_of_match,
>> + },
>> +};
>> +module_platform_driver(phy_berlin_usb_driver);
>> +
>> +MODULE_AUTHOR("Antoine Tenart <antoine.tenart@...e-electrons.com>");
>> +MODULE_DESCRIPTION("Marvell Berlin PHY driver for USB");
>> +MODULE_LICENSE("GPL");
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists