[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <1418006316-324-2-git-send-email-rjui@broadcom.com>
Date: Sun, 7 Dec 2014 18:38:32 -0800
From: Ray Jui <rjui@...adcom.com>
To: Rob Herring <robh+dt@...nel.org>, Pawel Moll <pawel.moll@....com>,
"Mark Rutland" <mark.rutland@....com>,
Ian Campbell <ijc+devicetree@...lion.org.uk>,
Kumar Gala <galak@...eaurora.org>,
"Linus Walleij" <linus.walleij@...aro.org>,
Alexandre Courbot <gnurou@...il.com>,
Grant Likely <grant.likely@...aro.org>,
Christian Daudt <bcm@...thebug.org>,
Matt Porter <mporter@...aro.org>,
Florian Fainelli <f.fainelli@...il.com>,
Russell King <linux@....linux.org.uk>,
Joe Perches <joe@...ches.com>
CC: Scott Branden <sbranden@...adcom.com>,
<linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-gpio@...r.kernel.org>,
<bcm-kernel-feedback-list@...adcom.com>,
<devicetree@...r.kernel.org>, "Ray Jui" <rjui@...adcom.com>
Subject: [PATCH v2 1/5] gpio: Cygnus: define Broadcom Cygnus GPIO binding
Document the GPIO device tree binding for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@...adcom.com>
Reviewed-by: Scott Branden <sbranden@...adcom.com>
---
.../devicetree/bindings/gpio/brcm,cygnus-gpio.txt | 85 ++++++++++++++++++++
1 file changed, 85 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gpio/brcm,cygnus-gpio.txt
diff --git a/Documentation/devicetree/bindings/gpio/brcm,cygnus-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,cygnus-gpio.txt
new file mode 100644
index 0000000..24a1513
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,cygnus-gpio.txt
@@ -0,0 +1,85 @@
+Broadcom Cygnus GPIO Controller
+
+Required properties:
+
+- compatible:
+ Currently supported Cygnus GPIO controllers include:
+ "brcm,cygnus-ccm-gpio": ChipcommonG GPIO controller
+ "brcm,cygnus-asiu-gpio": ASIU GPIO controller
+ "brcm,cygnus-crmu-gpio": CRMU GPIO controller
+
+- reg:
+ Define the base and range of the I/O address space that contain the Cygnus
+GPIO controller registers
+
+- ngpios:
+ Total number of GPIOs the controller provides
+
+- #gpio-cells:
+ Must be two. The first cell is the GPIO pin number (within the
+controller's domain) and the second cell is used for the following:
+ bit[0]: polarity (0 for normal and 1 for inverted)
+ bit[18:16]: internal pull up/down: 0 - pull up/down disabled
+ 1 - pull up enabled
+ 2 - pull down enabled
+ bit[22:20]: drive strength: 0 - 2 mA
+ 1 - 4 mA
+ 2 - 6 mA
+ 3 - 8 mA
+ 4 - 10 mA
+ 5 - 12 mA
+ 6 - 14 mA
+ 7 - 16 mA
+
+- gpio-controller:
+ Specifies that the node is a GPIO controller
+
+Optional properties:
+
+- interrupt-controller:
+ Specifies that the node is an interrupt controller. Not all Cygnus GPIO
+interfaces support interrupt, e.g., the CRMU GPIO controller does not have its
+interrupt routed to the main processor's GIC
+
+- interrupts:
+ The interrupt outputs from the GPIO controller.
+
+- no-interrupt:
+ Specifies that the GPIO interface does not support interrupt
+
+Example:
+ gpio_asiu: gpio@...a5000 {
+ compatible = "brcm,cygnus-asiu-gpio";
+ reg = <0x180a5000 0x668>;
+ ngpios = <122>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpio_crmu: gpio@...24800 {
+ compatible = "brcm,cygnus-crmu-gpio";
+ reg = <0x03024800 0x50>;
+ ngpios = <6>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ no-interrupt;
+ };
+
+ /*
+ * Touchscreen that uses the ASIU GPIO 100, with internal pull-up
+ * enabled
+ */
+ tsc {
+ ...
+ ...
+ gpio-event = <&gpio_asiu 100 0x10000>;
+ };
+
+ /* Bluetooth that uses the CRMU GPIO 2, with polarity inverted */
+ bluetooth {
+ ...
+ ...
+ bcm,rfkill-bank-sel = <&gpio_crmu 2 1>
+ }
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists