| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <548971AF.1020506@ti.com>
Date: Thu, 11 Dec 2014 15:57:59 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: Yunzhi Li <lyz@...k-chips.com>, <heiko@...ech.de>,
<jwerner@...omium.org>, <dianders@...omium.org>
CC: <olof@...om.net>, <huangtao@...k-chips.com>, <zyw@...k-chips.com>,
<cf@...k-chips.com>, <linux-rockchip@...ts.infradead.org>,
Grant Likely <grant.likely@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
<linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>
Subject: Re: [PATCH v6 1/5] phy: add a driver for the Rockchip SoC internal
USB2.0 PHY
Hi,
On Thursday 11 December 2014 03:25 PM, Yunzhi Li wrote:
> This patch to add a generic PHY driver for ROCKCHIP usb PHYs,
> currently this driver can support RK3288. The RK3288 SoC have
> three independent USB PHY IPs which are all configured through a
> set of registers located in the GRF (general register files)
> module.
>
> Signed-off-by: Yunzhi Li <lyz@...k-chips.com>
>
> ---
>
> Changes in v6:
> - Rename SIDDQ_MSK to SIDDQ_WRITE_ENA.
> - Use phandle args to find a phy struct directly.
>
> Changes in v5: None
> Changes in v4:
> - Get number of PHYs from device tree.
> - Model each PHY as subnode of the phy provider node.
>
> Changes in v3:
> - Use BIT macro instead of bit shift ops.
> - Rename the config entry to PHY_ROCKCHIP_USB.
>
> drivers/phy/Kconfig | 7 ++
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-rockchip-usb.c | 198 +++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 206 insertions(+)
> create mode 100644 drivers/phy/phy-rockchip-usb.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index ccad880..b24500a 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -239,6 +239,13 @@ config PHY_QCOM_IPQ806X_SATA
> depends on OF
> select GENERIC_PHY
>
> +config PHY_ROCKCHIP_USB
> + tristate "Rockchip USB2 PHY Driver"
> + depends on ARCH_ROCKCHIP && OF
> + select GENERIC_PHY
> + help
> + Enable this to support the Rockchip USB 2.0 PHY.
> +
> config PHY_ST_SPEAR1310_MIPHY
> tristate "ST SPEAR1310-MIPHY driver"
> select GENERIC_PHY
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index aa74f96..48bf5a1 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -28,6 +28,7 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o
> phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) += phy-s5pv210-usb2.o
> obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
> obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
> +obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
> obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
> obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
> diff --git a/drivers/phy/phy-rockchip-usb.c b/drivers/phy/phy-rockchip-usb.c
> new file mode 100644
> index 0000000..dad5194
> --- /dev/null
> +++ b/drivers/phy/phy-rockchip-usb.c
> @@ -0,0 +1,198 @@
> +/*
> + * Rockchip usb PHY driver
> + *
> + * Copyright (C) 2014 Yunzhi Li <lyz@...k-chips.com>
> + * Copyright (C) 2014 ROCKCHIP, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +#include <linux/regmap.h>
> +#include <linux/mfd/syscon.h>
> +
> +#define ROCKCHIP_RK3288_UOC(n) (0x320 + n * 0x14)
> +
> +/*
> + * The higher 16-bit of this register is used for write protection
> + * only if BIT(13 + 16) set to 1 the BIT(13) can be written.
> + */
> +#define SIDDQ_WRITE_ENA BIT(29)
> +#define SIDDQ_ON BIT(13)
> +#define SIDDQ_OFF (0 << 13)
> +
> +struct rockchip_usb_phy {
> + struct regmap *reg_base;
> + unsigned int reg_offset;
> + struct clk *clk;
> + struct phy *phy;
> +};
> +
> +struct rockchip_usb_phy_priv {
> + struct rockchip_usb_phy *phys;
> + unsigned nphys;
> +};
> +
> +static int rockchip_usb_phy_power(struct rockchip_usb_phy *phy,
> + bool siddq)
> +{
> + return regmap_write(phy->reg_base, phy->reg_offset,
> + SIDDQ_WRITE_ENA | (siddq ? SIDDQ_ON : SIDDQ_OFF));
> +}
> +
> +static int rockchip_usb_phy_power_off(struct phy *_phy)
> +{
> + struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
> + int ret = 0;
> +
> + /* Power down usb phy analog blocks by set siddq 1 */
> + ret = rockchip_usb_phy_power(phy, 1);
> + if (ret)
> + return ret;
> +
> + clk_disable_unprepare(phy->clk);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int rockchip_usb_phy_power_on(struct phy *_phy)
> +{
> + struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
> + int ret = 0;
> +
> + ret = clk_prepare_enable(phy->clk);
> + if (ret)
> + return ret;
> +
> + /* Power up usb phy analog blocks by set siddq 0 */
> + ret = rockchip_usb_phy_power(phy, 0);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static struct phy *rockchip_usb_phy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct rockchip_usb_phy_priv *priv = dev_get_drvdata(dev);
> + unsigned int phy_id = args->args[0];
> +
> + if (WARN_ON(phy_id < 0 || phy_id >= priv->nphys))
> + return ERR_PTR(-ENODEV);
> +
> + return priv->phys[phy_id].phy;
I didn't mean that. You can get rid of this entire xlate stuff if you use
something like below
phy@xxx {
compatible = "";
phy1:usb_phy {
}
phy2:usb_phy {
};
};
usb@xx {
compatible = "";
phys = <&phy1>; //doesn't need xlate
/* this needs xlate
phys = <&phy 1>;
*/
phy-names = "phy";
};
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists