Message-ID: <20150125160253.GG8470@lukather>
Date:	Sun, 25 Jan 2015 17:02:53 +0100
From:	Maxime Ripard <maxime.ripard@...e-electrons.com>
To:	Chen-Yu Tsai <wens@...e.org>
Cc:	Mike Turquette <mturquette@...aro.org>,
	Emilio Lopez <emilio@...pez.com.ar>,
	Rob Herring <robh+dt@...nel.org>,
	Grant Likely <grant.likely@...aro.org>,
	Kishon Vijay Abraham I <kishon@...com>,
	linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
	linux-kernel@...r.kernel.org, linux-sunxi@...glegroups.com
Subject: Re: [PATCH v2 1/9] clk: sunxi: Add support for sun9i a80 usb clocks
 and resets

Hi,

On Sun, Jan 25, 2015 at 08:22:02PM +0800, Chen-Yu Tsai wrote:
> The USB controller/phy clocks and reset controls are in a separate
> address block, unlike previous SoCs where they were in the clock
> controller.
> 
> This patch copies the original gates clk functions used for usb
> clocks into a separate file, and renames them to *_usb_*. Also
> add a per-gate parent index, so we can set different parents for
> each gate.
> 
> Signed-off-by: Chen-Yu Tsai <wens@...e.org>
> ---
>  Documentation/devicetree/bindings/clock/sunxi.txt |   2 +
>  drivers/clk/sunxi/Makefile                        |   1 +
>  drivers/clk/sunxi/clk-usb.c                       | 193 ++++++++++++++++++++++
>  3 files changed, 196 insertions(+)
>  create mode 100644 drivers/clk/sunxi/clk-usb.c
> 
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 60b44285250d..3f1dcd879af7 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -66,6 +66,8 @@ Required properties:
>  	"allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20
>  	"allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13
>  	"allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31
> +	"allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80
> +	"allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
>  
>  Required properties for all clocks:
>  - reg : shall be the control register address for the clock.
> diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
> index 3a5292e3fcf8..058f273d6154 100644
> --- a/drivers/clk/sunxi/Makefile
> +++ b/drivers/clk/sunxi/Makefile
> @@ -9,6 +9,7 @@ obj-y += clk-mod0.o
>  obj-y += clk-sun8i-mbus.o
>  obj-y += clk-sun9i-core.o
>  obj-y += clk-sun9i-mmc.o
> +obj-y += clk-usb.o

Is that supposed to handle the other USB clocks in the future as well?

>  
>  obj-$(CONFIG_MFD_SUN6I_PRCM) += \
>  	clk-sun6i-ar100.o clk-sun6i-apb0.o clk-sun6i-apb0-gates.o \
> diff --git a/drivers/clk/sunxi/clk-usb.c b/drivers/clk/sunxi/clk-usb.c
> new file mode 100644
> index 000000000000..1a93400353de
> --- /dev/null
> +++ b/drivers/clk/sunxi/clk-usb.c
> @@ -0,0 +1,193 @@
> +/*
> + * Copyright 2013 Emilio López
> + *
> + * Emilio López <emilio@...pez.com.ar>

Hmmmm, the copyright notice seems weird :)

> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/clkdev.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/reset-controller.h>
> +#include <linux/spinlock.h>
> +
> +
> +/**
> + * sunxi_usb_reset... - reset bits in usb clk registers handling
> + */
> +
> +struct usb_reset_data {
> +	void __iomem			*reg;
> +	spinlock_t			*lock;
> +	struct clk			*clk;
> +	struct reset_controller_dev	rcdev;
> +};
> +
> +static int sunxi_usb_reset_assert(struct reset_controller_dev *rcdev,
> +			      unsigned long id)
> +{
> +	struct usb_reset_data *data = container_of(rcdev,
> +						   struct usb_reset_data,
> +						   rcdev);
> +	unsigned long flags;
> +	u32 reg;
> +
> +	clk_prepare_enable(data->clk);
> +	spin_lock_irqsave(data->lock, flags);
> +
> +	reg = readl(data->reg);
> +	writel(reg & ~BIT(id), data->reg);
> +
> +	spin_unlock_irqrestore(data->lock, flags);
> +	clk_disable_unprepare(data->clk);
> +
> +	return 0;
> +}
> +
> +static int sunxi_usb_reset_deassert(struct reset_controller_dev *rcdev,
> +				unsigned long id)
> +{
> +	struct usb_reset_data *data = container_of(rcdev,
> +						     struct usb_reset_data,
> +						     rcdev);
> +	unsigned long flags;
> +	u32 reg;
> +
> +	clk_prepare_enable(data->clk);
> +	spin_lock_irqsave(data->lock, flags);
> +
> +	reg = readl(data->reg);
> +	writel(reg | BIT(id), data->reg);
> +
> +	spin_unlock_irqrestore(data->lock, flags);
> +	clk_disable_unprepare(data->clk);
> +
> +	return 0;
> +}
> +
> +static struct reset_control_ops sunxi_usb_reset_ops = {
> +	.assert		= sunxi_usb_reset_assert,
> +	.deassert	= sunxi_usb_reset_deassert,
> +};
> +
> +/**
> + * sunxi_usb_clk_setup() - Setup function for usb gate clocks
> + */
> +
> +#define SUNXI_USB_MAX_SIZE 32
> +
> +struct usb_clk_data {
> +	u32 clk_mask;
> +	u32 reset_mask;
> +	bool reset_needs_clk;
> +};
> +
> +static void __init sunxi_usb_clk_setup(struct device_node *node,
> +				       const struct usb_clk_data *data,
> +				       spinlock_t *lock)
> +{
> +	struct clk_onecell_data *clk_data;
> +	struct usb_reset_data *reset_data;
> +	const char *clk_parent;
> +	const char *clk_name;
> +	void __iomem *reg;
> +	int qty;
> +	int i = 0;
> +	int j = 0;
> +
> +	reg = of_io_request_and_map(node, 0, of_node_full_name(node));

You should check the return code here.

> +	clk_parent = of_clk_get_parent_name(node, 0);
> +	if (!clk_parent)
> +		return;
> +
> +	/* Worst-case size approximation and memory allocation */
> +	qty = find_last_bit((unsigned long *)&data->clk_mask,
> +			    SUNXI_USB_MAX_SIZE);

Newline

> +	clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
> +	if (!clk_data)
> +		return;

Newline.

> +	clk_data->clks = kzalloc((qty+1) * sizeof(struct clk *), GFP_KERNEL);
> +	if (!clk_data->clks) {
> +		kfree(clk_data);
> +		return;
> +	}
> +
> +	for_each_set_bit(i, (unsigned long *)&data->clk_mask,
> +			 SUNXI_USB_MAX_SIZE) {
> +		of_property_read_string_index(node, "clock-output-names",
> +					      j, &clk_name);
> +		clk_data->clks[i] = clk_register_gate(NULL, clk_name,
> +						      clk_parent, 0,
> +						      reg, i, 0, lock);
> +		WARN_ON(IS_ERR(clk_data->clks[i]));
> +		clk_register_clkdev(clk_data->clks[i], clk_name, NULL);

Do we really need to use clkdev for these clocks?

> +		j++;
> +	}
> +
> +	/* Adjust to the real max */
> +	clk_data->clk_num = i;
> +
> +	of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
> +
> +	/* Register a reset controller for usb with reset bits */
> +	if (data->reset_mask == 0)
> +		return;
> +
> +	reset_data = kzalloc(sizeof(*reset_data), GFP_KERNEL);
> +	if (!reset_data)
> +		return;
> +
> +	if (data->reset_needs_clk)
> +		reset_data->clk = of_clk_get(node, 0);

Newline

> +	if (IS_ERR(reset_data->clk)) {
> +		pr_err("Could not get clock for reset controls\n");
> +		kfree(reset_data);
> +		return;
> +	}

Newline, and that block should probably be part of the if block above.

> +	reset_data->reg = reg;
> +	reset_data->lock = lock;
> +	reset_data->rcdev.nr_resets = __fls(data->reset_mask) + 1;
> +	reset_data->rcdev.ops = &sunxi_usb_reset_ops;
> +	reset_data->rcdev.of_node = node;
> +	reset_controller_register(&reset_data->rcdev);
> +}
> +
> +static const struct usb_clk_data sun9i_a80_usb_mod_data __initconst = {
> +	.clk_mask = BIT(6) | BIT(5) | BIT(4) | BIT(3) | BIT(2) | BIT(1),
> +	.reset_mask = BIT(19) | BIT(18) | BIT(17),
> +	.reset_needs_clk = 1,
> +};
> +
> +static DEFINE_SPINLOCK(a80_usb_mod_lock);
> +
> +static void __init sun9i_a80_usb_mod_setup(struct device_node *node)
> +{
> +	sunxi_usb_clk_setup(node, &sun9i_a80_usb_mod_data, &a80_usb_mod_lock);
> +}
> +CLK_OF_DECLARE(sun9i_a80_usb_mod, "allwinner,sun9i-a80-usb-mod-clk", sun9i_a80_usb_mod_setup);
> +
> +static const struct usb_clk_data sun9i_a80_usb_phy_data __initconst = {
> +	.clk_mask = BIT(10) | BIT(5) | BIT(4) | BIT(3) | BIT(2) | BIT(1),
> +	.reset_mask = BIT(21) | BIT(20) | BIT(19) | BIT(18) | BIT(17),
> +	.reset_needs_clk = 1,
> +};
> +
> +static DEFINE_SPINLOCK(a80_usb_phy_lock);
> +
> +static void __init sun9i_a80_usb_phy_setup(struct device_node *node)
> +{
> +	sunxi_usb_clk_setup(node, &sun9i_a80_usb_phy_data, &a80_usb_phy_lock);
> +}
> +CLK_OF_DECLARE(sun9i_a80_usb_phy, "allwinner,sun9i-a80-usb-phy-clk", sun9i_a80_usb_phy_setup);

Looks good otherwise, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Download attachment "signature.asc" of type "application/pgp-signature" (820 bytes)

Powered by blists - more mailing lists