Message-id: <1422337703-11289-2-git-send-email-a.kesavan@samsung.com>
Date:	Tue, 27 Jan 2015 11:18:22 +0530
From:	Abhilash Kesavan <a.kesavan@...sung.com>
To:	rui.zhang@...el.com, edubezval@...il.com, kgene.kim@...sung.com,
	linux-pm@...r.kernel.org
Cc:	linux-kernel@...r.kernel.org, b.zolnierkie@...sung.com,
	l.majewski@...sung.com, amit.daniel@...sung.com,
	kesavan.abhilash@...il.com, linux-samsung-soc@...r.kernel.org
Subject: [PATCH v4 2/2] thermal: exynos: Add TMU support for Exynos7 SoC

Add registers, bit fields and compatible strings for Exynos7 TMU
(Thermal Management Unit). Following are a few of the differences
in the Exynos7 TMU from earlier SoCs:
        - 8 trigger levels
        - Different bit offsets and more registers for the rising
        and falling thresholds.
        - New power down detection bit in the TMU_CONTROL register
        which does not update the CURRENT_TEMP0 when tmu power down
        is detected.
        - Change in bit offset for the NEXT_DATA field of EMUL_CON
        register. EMUL_CON register address has also changed.
        - INTSTAT and INTCLEAR registers present in earlier SoCs
        have been combined into one INTPEND register. The register
        address for INTCLEAR and INTPEND is also different.
        - Since there are 8 rising/falling interrupts as against
        at most 4 in earlier SoCs the INTEN bit offsets are different.
        - Multiple probe support which is handled by a TMU_CONTROL1
        register (No support for this in the current patch).

This patch adds special clock support required only for Exynos7. It
also updates the "code_to_temp" prototype as Exynos7 has 9 bit
code-temp mapping.

Signed-off-by: Abhilash Kesavan <a.kesavan@...sung.com>
---
This patch set has been tested on linux next-20150123 with Eduardo's
thermal-next branch merged along with the arch-side exynos7 related
dts changes applied.

Changes since v3:
Addressed comments from Lukasz Majewski:
	- Added more comments in the code setting the thresholds.
	- Split the documentation out into another patch.
Changes since v2:
	- Rebased on top of Lukasz' latest exynos tmu series (v4).
	- Added new exynos7 soc_type.
Changes since v1:
	- Rebased on top of Lukasz' latest exynos tmu series (v2).
	- Added sclk support to patch adding Exynos7 tmu support.
	Previously, it was a separate patch.
	- Used the SOC type to decide if sclk is present.

 drivers/thermal/samsung/exynos_tmu.c |  204 ++++++++++++++++++++++++++++++++--
 drivers/thermal/samsung/exynos_tmu.h |    1 +
 2 files changed, 197 insertions(+), 8 deletions(-)

diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index 852e622..660ff69 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -119,6 +119,26 @@
 #define EXYNOS5440_TMU_TH_RISE4_SHIFT		24
 #define EXYNOS5440_EFUSE_SWAP_OFFSET		8
 
+/* Exynos7 specific registers */
+#define EXYNOS7_THD_TEMP_RISE7_6		0x50
+#define EXYNOS7_THD_TEMP_FALL7_6		0x60
+#define EXYNOS7_TMU_REG_INTEN			0x110
+#define EXYNOS7_TMU_REG_INTPEND			0x118
+#define EXYNOS7_TMU_REG_EMUL_CON		0x160
+
+#define EXYNOS7_TMU_TEMP_MASK			0x1ff
+#define EXYNOS7_PD_DET_EN_SHIFT			23
+#define EXYNOS7_TMU_INTEN_RISE0_SHIFT		0
+#define EXYNOS7_TMU_INTEN_RISE1_SHIFT		1
+#define EXYNOS7_TMU_INTEN_RISE2_SHIFT		2
+#define EXYNOS7_TMU_INTEN_RISE3_SHIFT		3
+#define EXYNOS7_TMU_INTEN_RISE4_SHIFT		4
+#define EXYNOS7_TMU_INTEN_RISE5_SHIFT		5
+#define EXYNOS7_TMU_INTEN_RISE6_SHIFT		6
+#define EXYNOS7_TMU_INTEN_RISE7_SHIFT		7
+#define EXYNOS7_EMUL_DATA_SHIFT			7
+#define EXYNOS7_EMUL_DATA_MASK			0x1ff
+
 #define MCELSIUS	1000
 /**
  * struct exynos_tmu_data : A structure to hold the private data of the TMU
@@ -133,6 +153,7 @@
  * @lock: lock to implement synchronization.
  * @clk: pointer to the clock structure.
  * @clk_sec: pointer to the clock structure for accessing the base_second.
+ * @sclk: pointer to the clock structure for accessing the tmu special clk.
  * @temp_error1: fused value of the first point trim.
  * @temp_error2: fused value of the second point trim.
  * @regulator: pointer to the TMU regulator structure.
@@ -152,8 +173,8 @@ struct exynos_tmu_data {
 	enum soc_type soc;
 	struct work_struct irq_work;
 	struct mutex lock;
-	struct clk *clk, *clk_sec;
-	u8 temp_error1, temp_error2;
+	struct clk *clk, *clk_sec, *sclk;
+	u16 temp_error1, temp_error2;
 	struct regulator *regulator;
 	struct thermal_zone_device *tzd;
 
@@ -223,7 +244,7 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
  * Calculate a temperature value from a temperature code.
  * The unit of the temperature is degree Celsius.
  */
-static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
+static int code_to_temp(struct exynos_tmu_data *data, u16 temp_code)
 {
 	struct exynos_tmu_platform_data *pdata = data->pdata;
 	int temp;
@@ -513,6 +534,84 @@ static int exynos5440_tmu_initialize(struct platform_device *pdev)
 	return ret;
 }
 
+static int exynos7_tmu_initialize(struct platform_device *pdev)
+{
+	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+	struct thermal_zone_device *tz = data->tzd;
+	struct exynos_tmu_platform_data *pdata = data->pdata;
+	unsigned int status, trim_info;
+	unsigned int rising_threshold = 0, falling_threshold = 0;
+	int ret = 0, threshold_code, i;
+	unsigned long temp, temp_hist;
+	unsigned int reg_off, bit_off;
+
+	status = readb(data->base + EXYNOS_TMU_REG_STATUS);
+	if (!status) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	trim_info = readl(data->base + EXYNOS_TMU_REG_TRIMINFO);
+
+	data->temp_error1 = trim_info & EXYNOS7_TMU_TEMP_MASK;
+	if (!data->temp_error1 ||
+	   (pdata->min_efuse_value > data->temp_error1) ||
+	   (data->temp_error1 > pdata->max_efuse_value))
+		data->temp_error1 = pdata->efuse_value & EXYNOS_TMU_TEMP_MASK;
+
+	/* Write temperature code for rising and falling threshold */
+	for (i = (of_thermal_get_ntrips(tz) - 1); i >= 0; i--) {
+		/*
+		 * On exynos7 there are 4 rising and 4 falling threshold
+		 * registers (0x50-0x5c and 0x60-0x6c respectively). Each
+		 * register holds the value of two threshold levels (at bit
+		 * offsets 0 and 16). Based on the fact that there are atmost
+		 * eight possible trigger levels, calculate the register and
+		 * bit offsets where the threshold levels are to be written.
+		 *
+		 * e.g. EXYNOS7_THD_TEMP_RISE7_6 (0x50)
+		 * [24:16] - Threshold level 7
+		 * [8:0] - Threshold level 6
+		 * e.g. EXYNOS7_THD_TEMP_RISE5_4 (0x54)
+		 * [24:16] - Threshold level 5
+		 * [8:0] - Threshold level 4
+		 *
+		 * and similarly for falling thresholds.
+		 *
+		 * Based on the above, calculate the register and bit offsets
+		 * for rising/falling threshold levels and populate them.
+		 */
+		reg_off = ((7 - i) / 2) * 4;
+		bit_off = ((8 - i) % 2);
+
+		tz->ops->get_trip_temp(tz, i, &temp);
+		temp /= MCELSIUS;
+
+		tz->ops->get_trip_hyst(tz, i, &temp_hist);
+		temp_hist = temp - (temp_hist / MCELSIUS);
+
+		/* Set 9-bit temperature code for rising threshold levels */
+		threshold_code = temp_to_code(data, temp);
+		rising_threshold = readl(data->base +
+			EXYNOS7_THD_TEMP_RISE7_6 + reg_off);
+		rising_threshold &= ~(EXYNOS7_TMU_TEMP_MASK << (16 * bit_off));
+		rising_threshold |= threshold_code << (16 * bit_off);
+		writel(rising_threshold,
+		       data->base + EXYNOS7_THD_TEMP_RISE7_6 + reg_off);
+
+		/* Set 9-bit temperature code for falling threshold levels */
+		threshold_code = temp_to_code(data, temp_hist);
+		falling_threshold &= ~(EXYNOS7_TMU_TEMP_MASK << (16 * bit_off));
+		falling_threshold |= threshold_code << (16 * bit_off);
+		writel(falling_threshold,
+		       data->base + EXYNOS7_THD_TEMP_FALL7_6 + reg_off);
+	}
+
+	data->tmu_clear_irqs(data);
+out:
+	return ret;
+}
+
 static void exynos4210_tmu_control(struct platform_device *pdev, bool on)
 {
 	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
@@ -573,6 +672,46 @@ static void exynos5440_tmu_control(struct platform_device *pdev, bool on)
 	writel(con, data->base + EXYNOS5440_TMU_S0_7_CTRL);
 }
 
+static void exynos7_tmu_control(struct platform_device *pdev, bool on)
+{
+	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+	struct thermal_zone_device *tz = data->tzd;
+	unsigned int con, interrupt_en;
+
+	con = get_con_reg(data, readl(data->base + EXYNOS_TMU_REG_CONTROL));
+
+	if (on) {
+		con |= (1 << EXYNOS_TMU_CORE_EN_SHIFT);
+		interrupt_en =
+			(of_thermal_is_trip_valid(tz, 7)
+			<< EXYNOS7_TMU_INTEN_RISE7_SHIFT) |
+			(of_thermal_is_trip_valid(tz, 6)
+			<< EXYNOS7_TMU_INTEN_RISE6_SHIFT) |
+			(of_thermal_is_trip_valid(tz, 5)
+			<< EXYNOS7_TMU_INTEN_RISE5_SHIFT) |
+			(of_thermal_is_trip_valid(tz, 4)
+			<< EXYNOS7_TMU_INTEN_RISE4_SHIFT) |
+			(of_thermal_is_trip_valid(tz, 3)
+			<< EXYNOS7_TMU_INTEN_RISE3_SHIFT) |
+			(of_thermal_is_trip_valid(tz, 2)
+			<< EXYNOS7_TMU_INTEN_RISE2_SHIFT) |
+			(of_thermal_is_trip_valid(tz, 1)
+			<< EXYNOS7_TMU_INTEN_RISE1_SHIFT) |
+			(of_thermal_is_trip_valid(tz, 0)
+			<< EXYNOS7_TMU_INTEN_RISE0_SHIFT);
+
+		interrupt_en |=
+			interrupt_en << EXYNOS_TMU_INTEN_FALL0_SHIFT;
+	} else {
+		con &= ~(1 << EXYNOS_TMU_CORE_EN_SHIFT);
+		interrupt_en = 0; /* Disable all interrupts */
+	}
+	con |= 1 << EXYNOS7_PD_DET_EN_SHIFT;
+
+	writel(interrupt_en, data->base + EXYNOS7_TMU_REG_INTEN);
+	writel(con, data->base + EXYNOS_TMU_REG_CONTROL);
+}
+
 static int exynos_get_temp(void *p, long *temp)
 {
 	struct exynos_tmu_data *data = p;
@@ -602,9 +741,19 @@ static u32 get_emul_con_reg(struct exynos_tmu_data *data, unsigned int val,
 			val &= ~(EXYNOS_EMUL_TIME_MASK << EXYNOS_EMUL_TIME_SHIFT);
 			val |= (EXYNOS_EMUL_TIME << EXYNOS_EMUL_TIME_SHIFT);
 		}
-		val &= ~(EXYNOS_EMUL_DATA_MASK << EXYNOS_EMUL_DATA_SHIFT);
-		val |= (temp_to_code(data, temp) << EXYNOS_EMUL_DATA_SHIFT) |
-			EXYNOS_EMUL_ENABLE;
+		if (data->soc == SOC_ARCH_EXYNOS7) {
+			val &= ~(EXYNOS7_EMUL_DATA_MASK <<
+				EXYNOS7_EMUL_DATA_SHIFT);
+			val |= (temp_to_code(data, temp) <<
+				EXYNOS7_EMUL_DATA_SHIFT) |
+				EXYNOS_EMUL_ENABLE;
+		} else {
+			val &= ~(EXYNOS_EMUL_DATA_MASK <<
+				EXYNOS_EMUL_DATA_SHIFT);
+			val |= (temp_to_code(data, temp) <<
+				EXYNOS_EMUL_DATA_SHIFT) |
+				EXYNOS_EMUL_ENABLE;
+		}
 	} else {
 		val &= ~EXYNOS_EMUL_ENABLE;
 	}
@@ -620,6 +769,8 @@ static void exynos4412_tmu_set_emulation(struct exynos_tmu_data *data,
 
 	if (data->soc == SOC_ARCH_EXYNOS5260)
 		emul_con = EXYNOS5260_EMUL_CON;
+	else if (data->soc == SOC_ARCH_EXYNOS7)
+		emul_con = EXYNOS7_TMU_REG_EMUL_CON;
 	else
 		emul_con = EXYNOS_EMUL_CON;
 
@@ -683,6 +834,12 @@ static int exynos5440_tmu_read(struct exynos_tmu_data *data)
 	return readb(data->base + EXYNOS5440_TMU_S0_7_TEMP);
 }
 
+static int exynos7_tmu_read(struct exynos_tmu_data *data)
+{
+	return readw(data->base + EXYNOS_TMU_REG_CURRENT_TEMP) &
+		EXYNOS7_TMU_TEMP_MASK;
+}
+
 static void exynos_tmu_work(struct work_struct *work)
 {
 	struct exynos_tmu_data *data = container_of(work,
@@ -721,6 +878,8 @@ static void exynos4210_tmu_clear_irqs(struct exynos_tmu_data *data)
 	if (data->soc == SOC_ARCH_EXYNOS5260) {
 		tmu_intstat = EXYNOS5260_TMU_REG_INTSTAT;
 		tmu_intclear = EXYNOS5260_TMU_REG_INTCLEAR;
+	} else if (data->soc == SOC_ARCH_EXYNOS7) {
+		tmu_intstat = tmu_intclear = EXYNOS7_TMU_REG_INTPEND;
 	} else {
 		tmu_intstat = EXYNOS_TMU_REG_INTSTAT;
 		tmu_intclear = EXYNOS_TMU_REG_INTCLEAR;
@@ -782,6 +941,9 @@ static const struct of_device_id exynos_tmu_match[] = {
 	{
 		.compatible = "samsung,exynos5440-tmu",
 	},
+	{
+		.compatible = "samsung,exynos7-tmu",
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, exynos_tmu_match);
@@ -805,6 +967,8 @@ static int exynos_of_get_soc_type(struct device_node *np)
 		return SOC_ARCH_EXYNOS5420_TRIMINFO;
 	else if (of_device_is_compatible(np, "samsung,exynos5440-tmu"))
 		return SOC_ARCH_EXYNOS5440;
+	else if (of_device_is_compatible(np, "samsung,exynos7-tmu"))
+		return SOC_ARCH_EXYNOS7;
 
 	return -EINVAL;
 }
@@ -928,6 +1092,13 @@ static int exynos_map_dt_data(struct platform_device *pdev)
 		data->tmu_set_emulation = exynos5440_tmu_set_emulation;
 		data->tmu_clear_irqs = exynos5440_tmu_clear_irqs;
 		break;
+	case SOC_ARCH_EXYNOS7:
+		data->tmu_initialize = exynos7_tmu_initialize;
+		data->tmu_control = exynos7_tmu_control;
+		data->tmu_read = exynos7_tmu_read;
+		data->tmu_set_emulation = exynos4412_tmu_set_emulation;
+		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
+		break;
 	default:
 		dev_err(&pdev->dev, "Platform not supported\n");
 		return -EINVAL;
@@ -1018,21 +1189,37 @@ static int exynos_tmu_probe(struct platform_device *pdev)
 		goto err_clk_sec;
 	}
 
+	if (data->soc == SOC_ARCH_EXYNOS7) {
+		data->sclk = devm_clk_get(&pdev->dev, "tmu_sclk");
+		if (IS_ERR(data->sclk)) {
+			dev_err(&pdev->dev, "Failed to get sclk\n");
+			goto err_clk;
+		} else {
+			ret = clk_prepare_enable(data->sclk);
+			if (ret) {
+				dev_err(&pdev->dev, "Failed to enable sclk\n");
+				goto err_clk;
+			}
+		}
+	}
+
 	ret = exynos_tmu_initialize(pdev);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to initialize TMU\n");
-		goto err_clk;
+		goto err_sclk;
 	}
 
 	ret = devm_request_irq(&pdev->dev, data->irq, exynos_tmu_irq,
 		IRQF_TRIGGER_RISING | IRQF_SHARED, dev_name(&pdev->dev), data);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to request irq: %d\n", data->irq);
-		goto err_clk;
+		goto err_sclk;
 	}
 
 	exynos_tmu_control(pdev, true);
 	return 0;
+err_sclk:
+	clk_disable_unprepare(data->sclk);
 err_clk:
 	clk_unprepare(data->clk);
 err_clk_sec:
@@ -1052,6 +1239,7 @@ static int exynos_tmu_remove(struct platform_device *pdev)
 	thermal_zone_of_sensor_unregister(&pdev->dev, tzd);
 	exynos_tmu_control(pdev, false);
 
+	clk_disable_unprepare(data->sclk);
 	clk_unprepare(data->clk);
 	if (!IS_ERR(data->clk_sec))
 		clk_unprepare(data->clk_sec);
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index 9f9b1b8..4d71ec6 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -34,6 +34,7 @@ enum soc_type {
 	SOC_ARCH_EXYNOS5420,
 	SOC_ARCH_EXYNOS5420_TRIMINFO,
 	SOC_ARCH_EXYNOS5440,
+	SOC_ARCH_EXYNOS7,
 };
 
 /**
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists