linux-kernel - [PATCH v2 5/6] ARM: dts: exynos5250-snow: Enable wifi power-on

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1422468953-7594-6-git-send-email-javier.martinez@collabora.co.uk>
Date:	Wed, 28 Jan 2015 19:15:52 +0100
From:	Javier Martinez Canillas <javier.martinez@...labora.co.uk>
To:	Ulf Hansson <ulf.hansson@...aro.org>
Cc:	Kukjin Kim <kgene@...nel.org>,
	Doug Anderson <dianders@...omium.org>,
	Olof Johansson <olof@...om.net>,
	Arend van Spriel <arend@...adcom.com>,
	Srinivas Kandagatla <srinivas.kandagatla@...aro.org>,
	linux-samsung-soc@...r.kernel.org,
	linux-arm-kernel@...ts.infradead.org, linux-mmc@...r.kernel.org,
	devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
	Javier Martinez Canillas <javier.martinez@...labora.co.uk>
Subject: [PATCH v2 5/6] ARM: dts: exynos5250-snow: Enable wifi power-on

The Snow board has a MMC/SDIO wifi chip that is always powered but it
needs a power sequence involving a reset (active low) and an enable
(active high) pins. Both pins are marked as active low since the MMC
simple power sequence driver asserts the pins prior to the card power
up procedure and de-asserts the pins after the card has been powered.

So the reset line will be left de-asserted and the enable pin will be
left asserted.

The chip also needs an external 32kHz reference clock to be operational
that is by the MAX77686 PMIC clock.

Add a simple MMC power sequence provider for the wifi MMC/SDIO slot.

Signed-off-by: Javier Martinez Canillas <javier.martinez@...labora.co.uk>
---

Changes since v1:
 - Remove cap-sdio-irq from mmc3 dev node since is a separate change.
   Suggested by Arend van Spriel.
---
 arch/arm/boot/dts/exynos5250-snow.dts | 25 ++++++++++++++++++++++++-
 1 file changed, 24 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index b9aeec430527..b78712058903 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -229,6 +229,14 @@
 		power-supply = <&fet6>;
 		backlight = <&backlight>;
 	};
+
+	mmc3_pwrseq: mmc3_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */
+			      <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */
+		clocks = <&max77686 MAX77686_CLK_PMIC>;
+		clock-names = "ext_clock";
+	};
 };
 
 &dp {
@@ -536,12 +544,27 @@
 	samsung,dw-mshc-sdr-timing = <2 3>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
+	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>;
 	bus-width = <4>;
 	cap-sd-highspeed;
+	mmc-pwrseq = <&mmc3_pwrseq>;
 };
 
 &pinctrl_0 {
+	wifi_en: wifi-en {
+		samsung,pins = "gpx0-1";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	wifi_rst: wifi-rst {
+		samsung,pins = "gpx0-2";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
 	power_key_irq: power-key-irq {
 		samsung,pins = "gpx1-3";
 		samsung,pin-function = <0xf>;
-- 
2.1.3

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/