| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1425510624-22250-3-git-send-email-stefan@agner.ch>
Date: Thu, 5 Mar 2015 00:10:21 +0100
From: Stefan Agner <stefan@...er.ch>
To: dwmw2@...radead.org, computersforpeace@...il.com
Cc: robh+dt@...nel.org, pawel.moll@....com, mark.rutland@....com,
ijc+devicetree@...lion.org.uk, galak@...eaurora.org,
shawn.guo@...aro.org, kernel@...gutronix.de,
boris.brezillon@...e-electrons.com, marb@...at.de,
aaron@...tycactus.com, bpringlemeir@...ps.com,
linux-mtd@...ts.infradead.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
Stefan Agner <stefan@...er.ch>
Subject: [PATCH 2/5] mtd: nand: vf610_nfc: add hardware BCH-ECC support
This adds hardware ECC support using the BCH encoder in the NFC IP.
The ECC encoder supports up to 32-bit correction by using 60 error
correction bytes. There is no sub-page ECC step, ECC is calculated
always accross the whole page (up to 2k pages).
Signed-off-by: Bill Pringlemeir <bpringlemeir@...ps.com>
Signed-off-by: Stefan Agner <stefan@...er.ch>
---
drivers/mtd/nand/Kconfig | 6 +-
drivers/mtd/nand/vf610_nfc.c | 193 +++++++++++++++++++++++++++++++++++++------
2 files changed, 172 insertions(+), 27 deletions(-)
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 1be30a6..0fb97b3 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -464,8 +464,10 @@ config MTD_NAND_VF610_NFC
help
Enables support for NAND Flash Controller on some Freescale
processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
- The driver supports a maximum 2k page size. The driver
- currently does not support hardware ECC.
+ The driver supports a maximum 2k page size. With 2k pages and
+ 64 bytes or more of OOB, hardware ECC with up to 32-bit error
+ correction is supported. Hardware ECC is only enabled through
+ device tree.
config MTD_NAND_MXC
tristate "MXC NAND support"
diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/vf610_nfc.c
index 101fd20..c6fb379 100644
--- a/drivers/mtd/nand/vf610_nfc.c
+++ b/drivers/mtd/nand/vf610_nfc.c
@@ -19,6 +19,7 @@
* - Untested on MPC5125 and M54418.
* - DMA not used.
* - 2K pages or less.
+ * - Only 2K page w. 64+OOB and hardware ECC.
*/
#include <linux/module.h>
@@ -71,6 +72,8 @@
/* NFC ECC mode define */
#define ECC_BYPASS 0
+#define ECC_45_BYTE 6
+#define ECC_60_BYTE 7
/*** Register Mask and bit definitions */
@@ -103,6 +106,8 @@
#define STATUS_BYTE1_MASK 0x000000FF
/* NFC_FLASH_CONFIG Field */
+#define CONFIG_ECC_SRAM_ADDR_MASK 0x7FC00000
+#define CONFIG_ECC_SRAM_ADDR_SHIFT 22
#define CONFIG_ECC_SRAM_REQ_BIT (1<<21)
#define CONFIG_DMA_REQ_BIT (1<<20)
#define CONFIG_ECC_MODE_MASK 0x000E0000
@@ -123,13 +128,32 @@
#define NFC_TIMEOUT (HZ)
+/* ECC status placed at end of buffers. */
+#define ECC_SRAM_ADDR ((PAGE_2K+256-8) >> 3)
+#define ECC_STATUS_MASK 0x80
+#define ECC_ERR_COUNT 0x3F
+
+/*
+ * ECC status is stored at NFC_CFG[ECCADD] +4 for little-endian
+ * and +7 for big-endian SoCs.
+ */
+#ifdef CONFIG_SOC_VF610
+#define ECC_OFFSET 4
+#else
+#define ECC_OFFSET 7
+#endif
+
struct vf610_nfc_config {
+ bool hardware_ecc;
+ int ecc_strength;
+ int ecc_step_size;
int width;
int flash_bbt;
u32 clkrate;
+ u32 ecc_mode;
};
-struct fsl_nfc {
+struct vf610_nfc {
struct mtd_info mtd;
struct nand_chip chip;
struct device *dev;
@@ -149,27 +173,32 @@ struct fsl_nfc {
#define mtd_to_nfc(_mtd) container_of(_mtd, struct vf610_nfc, mtd)
-static u8 bbt_pattern[] = {'B', 'b', 't', '0' };
-static u8 mirror_pattern[] = {'1', 't', 'b', 'B' };
-
-static struct nand_bbt_descr bbt_main_descr = {
- .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
- NAND_BBT_2BIT | NAND_BBT_VERSION,
- .offs = 11,
- .len = 4,
- .veroffs = 15,
- .maxblocks = 4,
- .pattern = bbt_pattern,
+static struct nand_ecclayout vf610_nfc_ecc45 = {
+ .eccbytes = 45,
+ .eccpos = {19, 20, 21, 22, 23,
+ 24, 25, 26, 27, 28, 29, 30, 31,
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63},
+ .oobfree = {
+ {.offset = 2,
+ .length = 17} }
};
-static struct nand_bbt_descr bbt_mirror_descr = {
- .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
- NAND_BBT_2BIT | NAND_BBT_VERSION,
- .offs = 11,
- .len = 4,
- .veroffs = 15,
- .maxblocks = 4,
- .pattern = mirror_pattern,
+static struct nand_ecclayout vf610_nfc_ecc60 = {
+ .eccbytes = 60,
+ .eccpos = { 4, 5, 6, 7, 8, 9, 10, 11,
+ 12, 13, 14, 15, 16, 17, 18, 19,
+ 20, 21, 22, 23, 24, 25, 26, 27,
+ 28, 29, 30, 31, 32, 33, 34, 35,
+ 36, 37, 38, 39, 40, 41, 42, 43,
+ 44, 45, 46, 47, 48, 49, 50, 51,
+ 52, 53, 54, 55, 56, 57, 58, 59,
+ 60, 61, 62, 63 },
+ .oobfree = {
+ {.offset = 2,
+ .length = 2} }
};
static inline u32 vf610_nfc_read(struct vf610_nfc *nfc, uint reg)
@@ -470,6 +499,60 @@ static void vf610_nfc_select_chip(struct mtd_info *mtd, int chip)
#endif
}
+/* Count the number of 0's in buff up to max_bits */
+static inline int count_written_bits(uint8_t *buff, int size, int max_bits)
+{
+ uint32_t *buff32 = (uint32_t *)buff;
+ int k, written_bits = 0;
+
+ for (k = 0; k < (size / 4); k++) {
+ written_bits += hweight32(~buff32[k]);
+ if (written_bits > max_bits)
+ break;
+ }
+
+ return written_bits;
+}
+
+static inline int vf610_nfc_correct_data(struct mtd_info *mtd, uint8_t *dat,
+ uint8_t *read_ecc, uint8_t *calc_ecc)
+{
+ struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+ u8 ecc_status;
+ u8 ecc_count;
+ int flip;
+
+ ecc_status = __raw_readb(nfc->regs + ECC_SRAM_ADDR * 8 + ECC_OFFSET);
+ ecc_count = ecc_status & ECC_ERR_COUNT;
+ if (!(ecc_status & ECC_STATUS_MASK))
+ return ecc_count;
+
+ /*
+ * On an erased page, bit count should be zero or at least
+ * less then half of the ECC strength
+ */
+ flip = count_written_bits(dat, nfc->chip.ecc.size, ecc_count);
+
+ if (flip > ecc_count && flip > (nfc->chip.ecc.strength / 2)) {
+ nfc->page = -1;
+ return -1;
+ }
+
+ /* Erased page. */
+ memset(dat, 0xff, nfc->chip.ecc.size);
+ return 0;
+}
+
+static int vf610_nfc_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
+ u_char *ecc_code)
+{
+ return 0;
+}
+
+static void vf610_nfc_enable_hwecc(struct mtd_info *mtd, int mode)
+{
+}
+
#ifdef CONFIG_OF_MTD
static const struct of_device_id vf610_nfc_dt_ids[] = {
{ .compatible = "fsl,vf610-nfc" },
@@ -487,7 +570,17 @@ static int vf610_nfc_probe_dt(struct device *dev, struct vf610_nfc_config *cfg)
if (!np)
return 1;
+ if (of_get_nand_ecc_mode(np) >= NAND_ECC_HW)
+ cfg->hardware_ecc = 1;
+
cfg->flash_bbt = of_get_nand_on_flash_bbt(np);
+ cfg->ecc_strength = of_get_nand_ecc_strength(np);
+ if (cfg->ecc_strength < 0)
+ cfg->ecc_strength = 0;
+
+ cfg->ecc_step_size = of_get_nand_ecc_step_size(np);
+ if (cfg->ecc_step_size < 0)
+ cfg->ecc_step_size = 0;
if (!of_property_read_u32(np, "clock-frequency", &clkrate))
cfg->clkrate = clkrate;
@@ -534,6 +627,15 @@ static int vf610_nfc_init_controller(struct vf610_nfc *nfc, int page_sz)
vf610_nfc_write(nfc, NFC_SECTOR_SIZE, page_sz);
+ if (cfg->hardware_ecc) {
+ vf610_nfc_set_field(nfc, NFC_FLASH_CONFIG,
+ CONFIG_ECC_MODE_MASK,
+ CONFIG_ECC_MODE_SHIFT, cfg->ecc_mode);
+
+ /* Enable ECC_STATUS */
+ vf610_nfc_set(nfc, NFC_FLASH_CONFIG, CONFIG_ECC_SRAM_REQ_BIT);
+ }
+
return 0;
}
@@ -610,10 +712,8 @@ static int vf610_nfc_probe(struct platform_device *pdev)
/* Bad block options. */
if (cfg->flash_bbt)
- chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_CREATE;
-
- chip->bbt_td = &bbt_main_descr;
- chip->bbt_md = &bbt_mirror_descr;
+ chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB |
+ NAND_BBT_CREATE;
init_waitqueue_head(&nfc->irq_waitq);
@@ -640,13 +740,56 @@ static int vf610_nfc_probe(struct platform_device *pdev)
/* Single buffer only, max 256 OOB minus ECC status */
if (page_sz > PAGE_2K + 256 - 8) {
- dev_err(nfc->dev, "Unsupported flash size\n");
+ dev_err(nfc->dev, "Unsupported flash page size\n");
err = -ENXIO;
goto error;
}
page_sz += cfg->width == 16 ? 1 : 0;
vf610_nfc_write(nfc, NFC_SECTOR_SIZE, page_sz);
+ if (cfg->hardware_ecc) {
+ if (mtd->writesize != PAGE_2K && mtd->oobsize < 64) {
+ dev_err(nfc->dev, "Unsupported flash with hwecc\n");
+ err = -ENXIO;
+ goto error;
+ }
+
+ if (cfg->ecc_step_size != mtd->writesize) {
+ dev_err(nfc->dev, "Step size needs to be page size\n");
+ err = -ENXIO;
+ goto error;
+ }
+
+ if (cfg->ecc_strength == 32) {
+ cfg->ecc_mode = ECC_60_BYTE;
+ chip->ecc.bytes = 60;
+ chip->ecc.layout = &vf610_nfc_ecc60;
+ } else if (cfg->ecc_strength == 24) {
+ cfg->ecc_mode = ECC_45_BYTE;
+ chip->ecc.bytes = 45;
+ chip->ecc.layout = &vf610_nfc_ecc45;
+ } else {
+ dev_err(nfc->dev, "Unsupported ECC strength\n");
+ err = -ENXIO;
+ goto error;
+ }
+
+ /* propagate ecc.layout to mtd_info */
+ mtd->ecclayout = chip->ecc.layout;
+ chip->ecc.calculate = vf610_nfc_calculate_ecc;
+ chip->ecc.hwctl = vf610_nfc_enable_hwecc;
+ chip->ecc.correct = vf610_nfc_correct_data;
+ chip->ecc.mode = NAND_ECC_HW;
+
+ chip->ecc.size = PAGE_2K;
+ chip->ecc.strength = cfg->ecc_strength;
+
+ /* set ECC mode according to required ECC strength */
+ vf610_nfc_set_field(nfc, NFC_FLASH_CONFIG,
+ CONFIG_ECC_MODE_MASK,
+ CONFIG_ECC_MODE_SHIFT, cfg->ecc_mode);
+ }
+
/* second phase scan */
if (nand_scan_tail(mtd)) {
err = -ENXIO;
--
2.3.0
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists