linux-kernel - Re: [PATCH 0/4] clk: si5351: Some fixes

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <20150508005220.GA3404@deathray>
Date:	Thu, 7 May 2015 19:52:20 -0500
From:	Michael Welling <mwelling@...e.org>
To:	Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>
Cc:	Mike Turquette <mturquette@...aro.org>,
	Stephen Boyd <sboyd@...eaurora.org>,
	Jean-Francois Moine <moinejf@...e.fr>,
	Russell King <rmk+linux@....linux.org.uk>,
	Jason Cooper <jason@...edaemon.net>,
	Andrew Lunn <andrew@...n.ch>,
	Gregory Clement <gregory.clement@...e-electrons.com>,
	devicetree@...r.kernel.org, linux-clk@...r.kernel.org,
	linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 0/4] clk: si5351: Some fixes

On Fri, May 01, 2015 at 10:17:35AM +0200, Sebastian Hesselbarth wrote:
> On 01.05.2015 00:36, Michael Welling wrote:
> >On Fri, May 01, 2015 at 12:21:20AM +0200, Sebastian Hesselbarth wrote:
> >>On 30.04.2015 23:20, Michael Welling wrote:
> >>>On Thu, Apr 30, 2015 at 10:44:07PM +0200, Sebastian Hesselbarth wrote:
> >>[...]
> >>>>What I noticed about your clk2 that you always measure as 0 Hz is
> >>>>that none of your clocks is prepared/enabled.
> >>>>
> >>>>Currently, the si5351 driver only ensures the output is enabled
> >>>>when si5351_clkout_prepare() is called.
> >>>>
> >>>>As long as you do not have a clk consumer that properly prepare/enables
> >>>>the clock output, it may remain disabled.
> >>>>
> >>>>We should probably have additional DT properties and corresponding
> >>>>pdata to force clkoutN always on.
> >>>
> >>>Does the silabs,disable-state of 3 (SI5351_DISABLE_NEVER) take care
> >>>of this?
> >>
> >>That would be the HW version of never disabling the clock output.
> >>I never really tried the property, does it work as expected?
> >
> >This did not appear to effect the behavior.
> 
> I think it is also a good idea to expose register values to debugfs,
> so we can easily check what is really written into internal registers.
> 
> >>
> >>>Otherwise is there a simple registration that will do this?
> >>
> >>The SW version of such a property would involve CLK_IGNORE_UNUSED
> >>and enabling all requested clock outputs on probe().
> >>
> >>If above HW property already works, I think it should be enough.
> >>
> >>[...]
> >>>>>It should be noted that if I program the device's register map in the
> >>>>>bootloader the device keeps the correct frequency outputs.
> >>>>
> >>>>"keeps"? You mean "generates", don't you?
> >>>>
> >>>
> >>>Yes the clocks are generated and do not get effected by the driver.
> >>
> >>IIRC, clk API does check if requested rate and current rate match
> >>already. If they do, it does not request the same rate again.
> >
> >So I found that the audio codec that I am driving with clk2 could
> >register the clock and allowed the clock to be enabled and disabled
> >by playing audio.
> >
> >This is when I noticed some strange behavior. The first time I attempt
> >to play audio the clock does not turn on blocking the audio from playing.
> >After I interrupt and the clock is disabled for the first time, the
> >successive clock enables work as expected.
> 
> Does "does not turn on" mean you cannot measure any clock on the
> output or is it just a guess because audio does not play?

The clock is stuck at around 2 volts until the first clk_disable.
When the clock is disabled it drops to GND. Future clk_enables make the
clock come at the reported frequency.

As for the clock being initialized incorrectly, I selectively added
mdelay(100) at each dev_dbg with debugging disabled until the 
initialization came up correct.

I found that adding a delay at the end of si5351_msynth_round_rate
appears to be magically fixing the incorrect frequency settings.
Not sure if this sheds any light on the issue but I figured I would 
share this information.

> 
> It could be that we just need to add some delay when we enable a clock
> output. Datasheet just says 10us max from OEB pin pulled low to valid
> clock output - not exactly what we are looking for but it could be a
> good start.
> 
> >Something tells me that a fault off some kind is occurring on initial
> >configuration.
> 
> What I noticed when adding the pll reset and checking DEVICE_STATUS is
> that SYS_INIT is still set. According to the datasheet, the meaning of
> the bit is that si5351 is still copying NVM content to its internal
> registers and therefore, we shouldn't try to access them.
> 
> What really irritates me about it is that it is seconds after power-up
> and copying the contents shouldn't really take _that_ long. However,
> the datasheet does not mention anything about how long it may take.
> 
> Sebastian
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/