| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1432087805-16671-4-git-send-email-robh@kernel.org>
Date: Tue, 19 May 2015 21:10:02 -0500
From: Rob Herring <robh@...nel.org>
To: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Peter Chen <peter.chen@...escale.com>,
Kishon Vijay Abraham I <kishon@...com>
Cc: linux-usb@...r.kernel.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org, Arnd Bergmann <arnd@...db.de>,
Alan Stern <stern@...land.harvard.edu>,
Rob Herring <robh@...nel.org>
Subject: [PATCH v2 3/6] phy: add Marvell HSIC 28nm PHY
Add PHY driver for the Marvell HSIC 28nm PHY. This PHY is found in PXA1928
SOC.
Signed-off-by: Rob Herring <robh@...nel.org>
Cc: Kishon Vijay Abraham I <kishon@...com>
---
drivers/phy/Kconfig | 10 +++
drivers/phy/Makefile | 1 +
drivers/phy/phy-pxa-28nm-hsic.c | 193 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 204 insertions(+)
create mode 100644 drivers/phy/phy-pxa-28nm-hsic.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 71409a1..7d56c44 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -52,6 +52,16 @@ config PHY_EXYNOS_MIPI_VIDEO
Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
and EXYNOS SoCs.
+config PHY_PXA_28NM_HSIC
+ tristate "Marvell USB HSIC 28nm PHY Driver"
+ select GENERIC_PHY
+ help
+ Enable this to support Marvell USB HSIC PHY driver for Marvell
+ SoC. This driver will do the PHY initialization and shutdown.
+ The PHY driver will be used by Marvell ehci driver.
+
+ To compile this driver as a module, choose M here.
+
config PHY_PXA_28NM_USB2
tristate "Marvell USB 2.0 28nm PHY Driver"
select GENERIC_PHY
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 8524307..2c16963 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_BCM_KONA_USB2_PHY) += phy-bcm-kona-usb2.o
obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
obj-$(CONFIG_PHY_PXA_28NM_USB2) += phy-pxa-28nm-usb2.o
+obj-$(CONFIG_PHY_PXA_28NM_HSIC) += phy-pxa-28nm-hsic.o
obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
obj-$(CONFIG_PHY_MIPHY28LP) += phy-miphy28lp.o
obj-$(CONFIG_PHY_MIPHY365X) += phy-miphy365x.o
diff --git a/drivers/phy/phy-pxa-28nm-hsic.c b/drivers/phy/phy-pxa-28nm-hsic.c
new file mode 100644
index 0000000..83e0d4d
--- /dev/null
+++ b/drivers/phy/phy-pxa-28nm-hsic.c
@@ -0,0 +1,193 @@
+/*
+ * Copyright (C) 2015 Linaro, Ltd.
+ * Rob Herring <robh@...nel.org>
+ *
+ * Based on vendor driver:
+ * Copyright (C) 2013 Marvell Inc.
+ * Author: Chao Xie <xiechao.mail@...il.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+#define PHY_28NM_HSIC_CTRL 0x08
+#define PHY_28NM_HSIC_IMPCAL_CAL 0x18
+#define PHY_28NM_HSIC_PLL_CTRL01 0x1c
+#define PHY_28NM_HSIC_PLL_CTRL2 0x20
+#define PHY_28NM_HSIC_INT 0x28
+
+#define PHY_28NM_HSIC_PLL_SELLPFR_SHIFT 26
+#define PHY_28NM_HSIC_PLL_FBDIV_SHIFT 0
+#define PHY_28NM_HSIC_PLL_REFDIV_SHIFT 9
+
+#define PHY_28NM_HSIC_S2H_PU_PLL BIT(10)
+#define PHY_28NM_HSIC_H2S_PLL_LOCK BIT(15)
+#define PHY_28NM_HSIC_S2H_HSIC_EN BIT(7)
+#define S2H_DRV_SE0_4RESUME BIT(14)
+#define PHY_28NM_HSIC_H2S_IMPCAL_DONE BIT(27)
+
+#define PHY_28NM_HSIC_CONNECT_INT BIT(1)
+#define PHY_28NM_HSIC_HS_READY_INT BIT(2)
+
+struct mv_hsic_phy {
+ struct phy *phy;
+ struct platform_device *pdev;
+ void __iomem *base;
+ struct clk *clk;
+};
+
+static bool wait_for_reg(void __iomem *reg, u32 mask, unsigned long timeout)
+{
+ timeout += jiffies;
+ while (time_is_after_eq_jiffies(timeout)) {
+ if ((readl(reg) & mask) == mask)
+ return true;
+ msleep(1);
+ }
+ return false;
+}
+
+static int mv_hsic_phy_power_on(struct phy *phy)
+{
+ struct mv_hsic_phy *mv_phy = phy_get_drvdata(phy);
+ struct platform_device *pdev = mv_phy->pdev;
+ void __iomem *base = mv_phy->base;
+
+ clk_prepare_enable(mv_phy->clk);
+
+ /* Set reference clock */
+ writel(0x1 << PHY_28NM_HSIC_PLL_SELLPFR_SHIFT |
+ 0xf0 << PHY_28NM_HSIC_PLL_FBDIV_SHIFT |
+ 0xd << PHY_28NM_HSIC_PLL_REFDIV_SHIFT,
+ base + PHY_28NM_HSIC_PLL_CTRL01);
+
+ /* Turn on PLL */
+ writel(readl(base + PHY_28NM_HSIC_PLL_CTRL2) |
+ PHY_28NM_HSIC_S2H_PU_PLL,
+ base + PHY_28NM_HSIC_PLL_CTRL2);
+
+ /* Make sure PHY PLL is locked */
+ if (!wait_for_reg(base + PHY_28NM_HSIC_PLL_CTRL2,
+ PHY_28NM_HSIC_H2S_PLL_LOCK, HZ / 10)) {
+ dev_err(&pdev->dev, "HSIC PHY PLL not locked after 100mS.");
+ return -ETIMEDOUT;
+ }
+
+ /* Avoid SE0 state when resume for some device will take it as reset */
+ writel(readl(base + PHY_28NM_HSIC_CTRL) & ~S2H_DRV_SE0_4RESUME,
+ base + PHY_28NM_HSIC_CTRL);
+
+ /* Enable HSIC PHY */
+ writel(readl(base + PHY_28NM_HSIC_CTRL) | PHY_28NM_HSIC_S2H_HSIC_EN,
+ base + PHY_28NM_HSIC_CTRL);
+
+ /* Calibration Timing
+ * ____________________________
+ * CAL START ___|
+ * ____________________
+ * CAL_DONE ___________|
+ * | 400us |
+ */
+
+ /* Make sure PHY Calibration is ready */
+ if (!wait_for_reg(base + PHY_28NM_HSIC_IMPCAL_CAL,
+ PHY_28NM_HSIC_H2S_IMPCAL_DONE, HZ / 10)) {
+ dev_warn(&pdev->dev, "HSIC PHY READY not set after 100mS.");
+ return -ETIMEDOUT;
+ }
+
+ /* Waiting for HSIC connect int*/
+ if (!wait_for_reg(base + PHY_28NM_HSIC_INT,
+ PHY_28NM_HSIC_CONNECT_INT, HZ / 5)) {
+ dev_warn(&pdev->dev, "HSIC wait for connect interrupt timeout.");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int mv_hsic_phy_power_off(struct phy *phy)
+{
+ struct mv_hsic_phy *mv_phy = phy_get_drvdata(phy);
+ void __iomem *base = mv_phy->base;
+
+ writel(readl(base + PHY_28NM_HSIC_CTRL) & ~PHY_28NM_HSIC_S2H_HSIC_EN,
+ base + PHY_28NM_HSIC_CTRL);
+
+ clk_disable_unprepare(mv_phy->clk);
+ return 0;
+}
+
+static const struct phy_ops hsic_ops = {
+ .power_on = mv_hsic_phy_power_on,
+ .power_off = mv_hsic_phy_power_off,
+};
+
+static int mv_hsic_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct mv_hsic_phy *mv_phy;
+ struct resource *r;
+
+ mv_phy = devm_kzalloc(&pdev->dev, sizeof(*mv_phy), GFP_KERNEL);
+ if (!mv_phy)
+ return -ENOMEM;
+
+ mv_phy->pdev = pdev;
+
+ mv_phy->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(mv_phy->clk)) {
+ dev_err(&pdev->dev, "failed to get clock.\n");
+ return PTR_ERR(mv_phy->clk);
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mv_phy->base = devm_ioremap_resource(&pdev->dev, r);
+ if (IS_ERR(mv_phy->base))
+ return PTR_ERR(mv_phy->base);
+
+ mv_phy->phy = devm_phy_create(&pdev->dev, pdev->dev.of_node, &hsic_ops);
+ if (IS_ERR(mv_phy->phy))
+ return PTR_ERR(mv_phy->phy);
+
+ phy_set_drvdata(mv_phy->phy, mv_phy);
+
+ phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id mv_hsic_phy_dt_match[] = {
+ { .compatible = "marvell,pxa1928-hsic-phy", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mv_hsic_phy_dt_match);
+
+static struct platform_driver mv_hsic_phy_driver = {
+ .probe = mv_hsic_phy_probe,
+ .driver = {
+ .name = "mv-hsic-phy",
+ .of_match_table = of_match_ptr(mv_hsic_phy_dt_match),
+ },
+};
+module_platform_driver(mv_hsic_phy_driver);
+
+MODULE_AUTHOR("Rob Herring <robh@...nel.org>");
+MODULE_DESCRIPTION("Marvell HSIC phy driver");
+MODULE_LICENSE("GPL v2");
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists