| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <555DD9D5.3000206@ti.com>
Date: Thu, 21 May 2015 18:42:53 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: Ray Jui <rjui@...adcom.com>
CC: <linux-kernel@...r.kernel.org>,
"JD (Jiandong) Zheng" <jdzheng@...adcom.com>,
Arun Parameswaran <arunp@...adcom.com>,
<bcm-kernel-feedback-list@...adcom.com>
Subject: Re: [PATCH 2/5] phy: iproc-mdio: Initial iProc MDC/MDIO support
Hi,
On Wednesday 20 May 2015 06:53 AM, Ray Jui wrote:
> This adds the support for the iProc MDC/MDIO interface. Multiple iProc
> SoCs contain the MDC/MDIO interface that can be used for the host to
> communicate with various Serdes/PHYs including Ethernet, PCIe, USB, etc.
the term phy used in this driver is misleading. It's not a PHY actually.
This sounds more like a bus driver to me and should be present in drivers/bus?
Thanks
Kishon
>
> Signed-off-by: Ray Jui <rjui@...adcom.com>
> Reviewed-by: Arun Parameswaran <aparames@...adcom.com>
> Reviewed-by: JD (Jiandong) Zheng <jdzheng@...adcom.com>
> Reviewed-by: Scott Branden <sbranden@...adcom.com>
> ---
> drivers/phy/Kconfig | 12 ++
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-iproc-mdio.c | 249 ++++++++++++++++++++++++++++++++++++
> include/linux/phy/iproc_mdio_phy.h | 22 ++++
> 4 files changed, 284 insertions(+)
> create mode 100644 drivers/phy/phy-iproc-mdio.c
> create mode 100644 include/linux/phy/iproc_mdio_phy.h
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index a53bd5b..2664285 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -52,6 +52,18 @@ config PHY_EXYNOS_MIPI_VIDEO
> Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
> and EXYNOS SoCs.
>
> +config PHY_IPROC_MDIO
> + bool "Broadcom iProc MDC/MDIO driver"
> + depends on ARCH_BCM_IPROC
> + default ARCH_BCM_IPROC
> + help
> + Enable this to support the iProc generic MDC/MDIO interface found
> + in various iProc based SoCs. The generic MDC/MDIO interface can be
> + used to communicate with various types of Serdes/PHYs including
> + Ethernet, PCIe, USB, and etc.
> +
> + If unsure, say N.
> +
> config PHY_MVEBU_SATA
> def_bool y
> depends on ARCH_DOVE || MACH_DOVE || MACH_KIRKWOOD
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index f126251..d989dd7b 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -13,6 +13,7 @@ obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
> obj-$(CONFIG_PHY_MIPHY28LP) += phy-miphy28lp.o
> obj-$(CONFIG_PHY_MIPHY365X) += phy-miphy365x.o
> +obj-$(CONFIG_PHY_IPROC_MDIO) += phy-iproc-mdio.o
> obj-$(CONFIG_PHY_RCAR_GEN2) += phy-rcar-gen2.o
> obj-$(CONFIG_OMAP_CONTROL_PHY) += phy-omap-control.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> diff --git a/drivers/phy/phy-iproc-mdio.c b/drivers/phy/phy-iproc-mdio.c
> new file mode 100644
> index 0000000..a37e92f
> --- /dev/null
> +++ b/drivers/phy/phy-iproc-mdio.c
> @@ -0,0 +1,249 @@
> +/*
> + * Copyright (C) 2015 Broadcom Corporation
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/phy/iproc_mdio_phy.h>
> +
> +#define MDIO_TIMEOUT_MSEC 10
> +
> +#define MDC_CTRL_OFFSET 0x000
> +
> +#define MDC_CTRL_DIV_SHIFT 0
> +#define MDC_CTRL_DIV_WIDTH 7
> +#define MDC_MAX_DIV (BIT(MDC_CTRL_DIV_WIDTH) - 1)
> +#define MDC_CTRL_PRE_SHIFT 7
> +#define MDC_CTRL_BUSY_SHIFT 8
> +#define MDC_CTRL_EXT_SHIFT 9
> +#define MDC_CTRL_BTP_SHIFT 10
> +
> +#define MDC_DATA_OFFSET 0x004
> +
> +#define MDC_DATA_SHIFT 0
> +#define MDC_DATA_MASK 0xffff
> +
> +#define MDC_DATA_TA_SHIFT 16
> +#define MDC_DATA_TA_VAL 2
> +
> +#define MDC_DATA_RA_SHIFT 18
> +#define MDC_DATA_RA_WIDTH 5
> +#define MDC_MAX_RA (BIT(MDC_DATA_RA_WIDTH) - 1)
> +
> +#define MDC_DATA_PA_SHIFT 23
> +#define MDC_DATA_PA_WIDTH 5
> +#define MDC_MAX_PA (BIT(MDC_DATA_PA_WIDTH) - 1)
> +
> +#define MDC_DATA_OP_SHIFT 28
> +#define MDC_DATA_OP_WRITE 1
> +#define MDC_DATA_OP_READ 2
> +
> +#define MDC_DATA_SB_SHIFT 30
> +
> +/**
> + * struct iproc_mdc - iProc MDC/MDIO device
> + * @dev: pointer to device
> + * @base: MDC controller register base pointer
> + * @lock: mutex to protect access to the MDC device
> + * @is_ready: flag to indicate the driver has been initialized and is ready for
> + * use
> + */
> +struct iproc_mdc {
> + struct device *dev;
> + void __iomem *base;
> + struct mutex lock;
> + bool is_ready;
> +};
> +
> +static struct iproc_mdc iproc_mdc;
> +
> +static inline int iproc_mdio_check_params(unsigned clk_div, unsigned pa,
> + unsigned ra)
> +{
> + if (clk_div > MDC_MAX_DIV || pa > MDC_MAX_PA || ra > MDC_MAX_RA)
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static inline int iproc_mdio_wait_for_idle(void __iomem *base)
> +{
> + u32 val;
> + unsigned long timeout = jiffies + msecs_to_jiffies(MDIO_TIMEOUT_MSEC);
> +
> + while (!time_after(jiffies, timeout)) {
> + val = readl(base + MDC_CTRL_OFFSET);
> + if ((val & BIT(MDC_CTRL_BUSY_SHIFT)) == 0)
> + return 0;
> +
> + cpu_relax();
> + }
> +
> + return -ETIMEDOUT;
> +}
> +
> +static inline void iproc_mdio_config_clk(void __iomem *base, unsigned clk_div)
> +{
> + u32 val;
> +
> + val = (clk_div << MDC_CTRL_DIV_SHIFT) | BIT(MDC_CTRL_PRE_SHIFT);
> + writel(val, base + MDC_CTRL_OFFSET);
> +}
> +
> +static int iproc_mdio_read_write(void __iomem *base, bool dir_is_write,
> + unsigned clk_div, unsigned pa, unsigned ra,
> + u16 *data)
> +{
> + int ret;
> + u32 val;
> +
> + ret = iproc_mdio_check_params(clk_div, pa, ra);
> + if (ret)
> + return ret;
> +
> + ret = iproc_mdio_wait_for_idle(base);
> + if (ret)
> + return ret;
> +
> + iproc_mdio_config_clk(base, clk_div);
> +
> + ret = iproc_mdio_wait_for_idle(base);
> + if (ret)
> + return ret;
> +
> + val = (MDC_DATA_TA_VAL << MDC_DATA_TA_SHIFT) |
> + (ra << MDC_DATA_RA_SHIFT) |
> + (pa << MDC_DATA_PA_SHIFT) |
> + BIT(MDC_DATA_SB_SHIFT);
> +
> + if (dir_is_write) {
> + val |= (MDC_DATA_OP_WRITE << MDC_DATA_OP_SHIFT);
> + val |= ((u32)(*data) & MDC_DATA_MASK);
> + } else {
> + val |= (MDC_DATA_OP_READ << MDC_DATA_OP_SHIFT);
> + }
> +
> + writel(val, base + MDC_DATA_OFFSET);
> +
> + ret = iproc_mdio_wait_for_idle(base);
> + if (ret)
> + return ret;
> +
> + if (!dir_is_write) {
> + val = readl(base + MDC_DATA_OFFSET) & MDC_DATA_MASK;
> + *data = (u16)val;
> + }
> +
> + return 0;
> +}
> +
> +
> +/**
> + * iproc_mdio_read() - read from a PHY register through the MDC interface
> + *
> + * @clk_div: MDC clock divisor
> + * @phy_addr: MDC PHY address
> + * @reg_addr: PHY register address
> + * @data: pointer to the memory where data will be stored
> + */
> +int iproc_mdio_read(unsigned clk_div, unsigned phy_addr, unsigned reg_addr,
> + u16 *data)
> +{
> + int ret;
> + struct iproc_mdc *mdc = &iproc_mdc;
> +
> + if (!mdc->is_ready)
> + return -ENODEV;
> +
> + mutex_lock(&mdc->lock);
> + ret = iproc_mdio_read_write(mdc->base, false, clk_div, phy_addr,
> + reg_addr, data);
> + if (ret)
> + dev_err(mdc->dev, "mdio read failed\n");
> + mutex_unlock(&mdc->lock);
> +
> + return ret;
> +}
> +EXPORT_SYMBOL(iproc_mdio_read);
> +
> +/**
> + * iproc_mdio_write() - write to a PHY register through the MDC interface
> + *
> + * @clk_div: MDC clock divisor
> + * @phy_addr: MDC PHY address
> + * @reg_addr: PHY register address
> + * @data: data value to be written to the PHY register
> + */
> +int iproc_mdio_write(unsigned clk_div, unsigned phy_addr, unsigned reg_addr,
> + u16 data)
> +{
> + int ret;
> + struct iproc_mdc *mdc = &iproc_mdc;
> +
> + if (!mdc->is_ready)
> + return -ENODEV;
> +
> + mutex_lock(&mdc->lock);
> + ret = iproc_mdio_read_write(mdc->base, true, clk_div, phy_addr,
> + reg_addr, &data);
> + if (ret)
> + dev_err(mdc->dev, "mdio write failed\n");
> + mutex_unlock(&mdc->lock);
> +
> + return ret;
> +}
> +EXPORT_SYMBOL(iproc_mdio_write);
> +
> +static int iproc_mdio_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct iproc_mdc *mdc = &iproc_mdc;
> + struct resource *res;
> +
> + mdc->dev = dev;
> + mutex_init(&mdc->lock);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + mdc->base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(mdc->base))
> + return PTR_ERR(mdc->base);
> +
> + mdc->is_ready = true;
> + return 0;
> +}
> +
> +static const struct of_device_id iproc_mdio_match_table[] = {
> + { .compatible = "brcm,iproc-mdio" },
> + { }
> +};
> +
> +static struct platform_driver iproc_mdio_driver = {
> + .driver = {
> + .name = "iproc-mdio",
> + .of_match_table = iproc_mdio_match_table,
> + .suppress_bind_attrs = true,
> + },
> + .probe = iproc_mdio_probe,
> +};
> +
> +static int __init iproc_mdio_init(void)
> +{
> + return platform_driver_register(&iproc_mdio_driver);
> +}
> +arch_initcall_sync(iproc_mdio_init);
> +
> +MODULE_AUTHOR("Ray Jui <rjui@...adcom.com>");
> +MODULE_DESCRIPTION("Broadcom iPROC MDC/MDIO driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/phy/iproc_mdio_phy.h b/include/linux/phy/iproc_mdio_phy.h
> new file mode 100644
> index 0000000..d3e88ce
> --- /dev/null
> +++ b/include/linux/phy/iproc_mdio_phy.h
> @@ -0,0 +1,22 @@
> +/*
> + * Copyright (C) 2015 Broadcom Corporation
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef __IPROC_MDIO_PHY_H
> +#define __IPROC_MDIO_PHY_H
> +
> +int iproc_mdio_read(unsigned clk_div, unsigned phy_addr, unsigned reg_addr,
> + u16 *data);
> +int iproc_mdio_write(unsigned clk_div, unsigned phy_addr, unsigned reg_addr,
> + u16 data);
> +
> +#endif /* __IPROC_MDIO_PHY_H */
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists