linux-kernel - [PATCH V2 3/3] tty: serial: fsl_lpuart: Add support for RS-485

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1433136067-20644-4-git-send-email-bhuvanchandra.dv@toradex.com>
Date:	Mon, 1 Jun 2015 10:51:07 +0530
From:	Bhuvanchandra DV <bhuvanchandra.dv@...adex.com>
To:	<gregkh@...uxfoundation.org>
CC:	<linux-kernel@...r.kernel.org>, <stefan@...er.ch>,
	<shawn.guo@...aro.org>, <kernel@...gutronix.de>, <jslaby@...e.cz>,
	<moorray3@...pl>, <linux-serial@...r.kernel.org>,
	<linux-arm-kernel@...ts.infradead.org>,
	<devicetree@...r.kernel.org>, <bhuvanchandra.dv@...il.com>,
	Bhuvanchandra DV <bhuvanchandra.dv@...adex.com>
Subject: [PATCH V2 3/3] tty: serial: fsl_lpuart: Add support for RS-485

Enable Vybrid's build-in support for RS-485 auto RTS for
controlling line direction of RS-485 transceiver driver.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@...adex.com>
---
 drivers/tty/serial/fsl_lpuart.c | 56 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 532cfb7..7b4e04a 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -820,6 +820,49 @@ static unsigned int lpuart32_tx_empty(struct uart_port *port)
 		TIOCSER_TEMT : 0;
 }
 
+static int lpuart_config_rs485(struct uart_port *port,
+			struct serial_rs485 *rs485)
+{
+	struct lpuart_port *sport = container_of(port,
+			struct lpuart_port, port);
+	u8 modem = readb(sport->port.membase + UARTMODEM) &
+		~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
+
+	writeb(modem, sport->port.membase + UARTMODEM);
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		/* Enable auto RS-485 RTS mode */
+		modem |= UARTMODEM_TXRTSE;
+
+		/*
+		 * RTS needs to be logic HIGH either during transer _or_ after
+		 * transfer, other variants are not supported by the hardware.
+		 */
+		if (!(rs485->flags & (SER_RS485_RTS_ON_SEND |
+					SER_RS485_RTS_AFTER_SEND)))
+			rs485->flags |= SER_RS485_RTS_ON_SEND;
+
+		if (rs485->flags & SER_RS485_RTS_ON_SEND && rs485->flags &
+					SER_RS485_RTS_AFTER_SEND)
+			rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
+
+		/*
+		 * The hardware defaults to RTS logic HIGH while transfer.
+		 * Switch polarity in case RTS shall be logic HIGH
+		 * after transfer.
+		 * Note: UART is assumed to be active high.
+		 */
+		if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
+			modem |= UARTMODEM_TXRTSPOL;
+	}
+
+	/* Store the new configuration */
+	sport->port.rs485 = *rs485;
+
+	writeb(modem, sport->port.membase + UARTMODEM);
+	return 0;
+}
+
 static unsigned int lpuart_get_mctrl(struct uart_port *port)
 {
 	return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR;
@@ -1191,6 +1234,12 @@ lpuart_set_termios(struct uart_port *port, struct ktermios *termios,
 		cr1 |= UARTCR1_M;
 	}
 
+	/* When auto RS-485 RTS mode is enabled,
+	 * hardware flow control need to be disabled.
+	 */
+	if (sport->port.rs485.flags & SER_RS485_ENABLED)
+		termios->c_cflag &= ~CRTSCTS;
+
 	if (termios->c_cflag & CRTSCTS) {
 		modem |= (UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
 	} else {
@@ -1749,6 +1798,8 @@ static int lpuart_probe(struct platform_device *pdev)
 		sport->port.ops = &lpuart_pops;
 	sport->port.flags = UPF_BOOT_AUTOCONF;
 
+	sport->port.rs485_config = lpuart_config_rs485;
+
 	sport->clk = devm_clk_get(&pdev->dev, "ipg");
 	if (IS_ERR(sport->clk)) {
 		ret = PTR_ERR(sport->clk);
@@ -1789,6 +1840,11 @@ static int lpuart_probe(struct platform_device *pdev)
 		dev_info(sport->port.dev, "DMA rx channel request failed, "
 				"operating without rx DMA\n");
 
+	if (of_property_read_bool(np, "linux,rs485-enabled-at-boot-time")) {
+		sport->port.rs485.flags |= SER_RS485_ENABLED;
+		sport->port.rs485.flags |= SER_RS485_RTS_ON_SEND;
+		writeb(UARTMODEM_TXRTSE, sport->port.membase + UARTMODEM);
+
 	return 0;
 }
 
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/