| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <55A3D0A4.2050201@openwrt.org>
Date: Mon, 13 Jul 2015 16:52:20 +0200
From: John Crispin <blogic@...nwrt.org>
To: Chunfeng Yun <chunfeng.yun@...iatek.com>,
Mathias Nyman <mathias.nyman@...el.com>
CC: Mark Rutland <mark.rutland@....com>, devicetree@...r.kernel.org,
Sascha Hauer <s.hauer@...gutronix.de>,
linux-usb@...r.kernel.org, linux-kernel@...r.kernel.org,
Felipe Balbi <balbi@...com>, Rob Herring <robh+dt@...nel.org>,
linux-mediatek@...ts.infradead.org,
Matthias Brugger <matthias.bgg@...il.com>,
linux-arm-kernel@...ts.infradead.org, Roger Quadros <rogerq@...com>
Subject: Re: [PATCH v2 4/5] xhci: mediatek: support MTK xHCI host controller
Hi
there is a cross dependency between the modules. xhci-mtk.ko requires
xhci.ko to be loaded. however this will look for xhci_mtk_add_ep_quirk()
which is part of xhci-mtk. the modules will build but are not run time
loadable.
John
On 08/07/2015 11:41, Chunfeng Yun wrote:
> MTK xhci host controller defines some extra SW scheduling
> parameters for HW to minimize the scheduling effort for
> synchronous and interrupt endpoints. The parameters are
> put into reseved DWs of slot context and endpoint context
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@...iatek.com>
> ---
> drivers/usb/host/Kconfig | 9 +
> drivers/usb/host/Makefile | 1 +
> drivers/usb/host/xhci-mtk.c | 814 +++++++++++++++++++++++++++++++++++++++++++
> drivers/usb/host/xhci-mtk.h | 108 ++++++
> drivers/usb/host/xhci-ring.c | 35 +-
> drivers/usb/host/xhci.c | 19 +-
> drivers/usb/host/xhci.h | 1 +
> 7 files changed, 980 insertions(+), 7 deletions(-)
> create mode 100644 drivers/usb/host/xhci-mtk.c
> create mode 100644 drivers/usb/host/xhci-mtk.h
>
> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> index 8afc3c1..2202c68 100644
> --- a/drivers/usb/host/Kconfig
> +++ b/drivers/usb/host/Kconfig
> @@ -34,6 +34,15 @@ config USB_XHCI_PCI
> config USB_XHCI_PLATFORM
> tristate
>
> +config USB_XHCI_MTK
> + tristate "xHCI support for Mediatek MT65xx"
> + select USB_XHCI_PLATFORM
> + depends on ARCH_MEDIATEK || COMPILE_TEST
> + ---help---
> + Say 'Y' to enable the support for the xHCI host controller
> + found in Mediatek MT65xx SoCs.
> + If unsure, say N.
> +
> config USB_XHCI_MVEBU
> tristate "xHCI support for Marvell Armada 375/38x"
> select USB_XHCI_PLATFORM
> diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
> index 754efaa..90c6eb2 100644
> --- a/drivers/usb/host/Makefile
> +++ b/drivers/usb/host/Makefile
> @@ -30,6 +30,7 @@ endif
>
> obj-$(CONFIG_USB_XHCI_PCI) += xhci-pci.o
> obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
> +obj-$(CONFIG_USB_XHCI_MTK) += xhci-mtk.o
>
> obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
> obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
> diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
> new file mode 100644
> index 0000000..45f0606
> --- /dev/null
> +++ b/drivers/usb/host/xhci-mtk.c
> @@ -0,0 +1,814 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author:
> + * Zhigang.Wei <zhigang.wei@...iatek.com>
> + * Chunfeng.Yun <chunfeng.yun@...iatek.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/clk.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/usb/phy.h>
> +#include <linux/slab.h>
> +#include <linux/usb/xhci_pdriver.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/pm_runtime.h>
> +
> +#include "xhci.h"
> +#include "xhci-mtk.h"
> +
> +
> +#define SS_BW_BOUNDARY 51000
> +/* table 5-5. High-speed Isoc Transaction Limits in usb_20 spec */
> +#define HS_BW_BOUNDARY 6144
> +/* usb2 spec section11.18.1: at most 188 FS bytes per microframe */
> +#define FS_PAYLOAD_MAX 188
> +
> +/* mtk scheduler bitmasks */
> +#define EP_BPKTS(p) ((p) & 0x3f)
> +#define EP_BCSCOUNT(p) (((p) & 0x7) << 8)
> +#define EP_BBM(p) ((p) << 11)
> +#define EP_BOFFSET(p) ((p) & 0x3fff)
> +#define EP_BREPEAT(p) (((p) & 0x7fff) << 16)
> +
> +
> +struct xhci_hcd_mtk {
> + struct device *dev;
> + struct usb_hcd *hcd;
> + struct mu3h_sch_bw_info *sch_array;
> + struct regulator *vusb33;
> + struct regulator *vbus;
> + struct clk *sys_mac; /* sys and mac clock */
> +};
> +
> +
> +static int is_fs_or_ls(enum usb_device_speed speed)
> +{
> + return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
> +}
> +
> +static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
> + struct usb_host_endpoint *ep)
> +{
> + int bw_index;
> + int port_id;
> + struct xhci_virt_device *virt_dev;
> +
> + virt_dev = xhci->devs[udev->slot_id];
> + port_id = virt_dev->real_port;
> +
> + if (udev->speed == USB_SPEED_SUPER) {
> + if (usb_endpoint_dir_out(&ep->desc))
> + bw_index = (port_id - 1) * 2;
> + else
> + bw_index = (port_id - 1) * 2 + 1;
> + } else {
> + bw_index = port_id + xhci->num_usb3_ports - 1;
> + }
> +
> + return bw_index;
> +}
> +
> +
> +static void setup_sch_info(struct usb_device *udev,
> + struct xhci_ep_ctx *ep_ctx, struct mu3h_sch_ep_info *sch_ep)
> +{
> + u32 ep_type;
> + u32 ep_interval;
> + u32 max_packet_size;
> + u32 max_burst;
> + u32 mult;
> + u32 esit_pkts;
> +
> + ep_type = CTX_TO_EP_TYPE(le32_to_cpu(ep_ctx->ep_info2));
> + ep_interval = CTX_TO_EP_INTERVAL(le32_to_cpu(ep_ctx->ep_info));
> + max_packet_size = MAX_PACKET_DECODED(le32_to_cpu(ep_ctx->ep_info2));
> + max_burst = CTX_TO_MAX_BURST(le32_to_cpu(ep_ctx->ep_info2));
> + mult = CTX_TO_EP_MULT(le32_to_cpu(ep_ctx->ep_info));
> + pr_debug("%s: max_burst = %d, mult = %d\n", __func__, max_burst, mult);
> +
> + sch_ep->ep_type = ep_type;
> + sch_ep->max_packet_size = max_packet_size;
> + sch_ep->esit = 1 << ep_interval;
> + sch_ep->offset = 0;
> + sch_ep->burst_mode = 0;
> +
> + if (udev->speed == USB_SPEED_HIGH) {
> + sch_ep->cs_count = 0;
> + /*
> + * usb_20 spec section5.9
> + * a single microframe is enough for HS synchromous endpoints
> + * in a interval
> + */
> + sch_ep->num_budget_microframes = 1;
> + sch_ep->repeat = 0;
> + /*
> + * xHCI spec section6.2.3.4
> + * @max_busrt is the number of additional transactions
> + * opportunities per microframe
> + */
> + sch_ep->pkts = max_burst + 1;
> + sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
> + } else if (udev->speed == USB_SPEED_SUPER) {
> + /* usb3_r1 spec section4.4.7 & 4.4.8 */
> + sch_ep->cs_count = 0;
> + esit_pkts = (mult + 1) * (max_burst + 1);
> + if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
> + sch_ep->pkts = esit_pkts;
> + sch_ep->num_budget_microframes = 1;
> + sch_ep->repeat = 0;
> + }
> +
> + if (ep_type == ISOC_IN_EP || ep_type == ISOC_OUT_EP) {
> + if (esit_pkts <= sch_ep->esit)
> + sch_ep->pkts = 1;
> + else
> + sch_ep->pkts = roundup_pow_of_two(esit_pkts)
> + / sch_ep->esit;
> +
> + sch_ep->num_budget_microframes =
> + DIV_ROUND_UP(esit_pkts, sch_ep->pkts);
> +
> + if (sch_ep->num_budget_microframes > 1)
> + sch_ep->repeat = 1;
> + else
> + sch_ep->repeat = 0;
> + }
> + sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
> + } else if (is_fs_or_ls(udev->speed)) {
> + /*
> + * usb_20 spec section11.18.4
> + * assume worst cases
> + */
> + sch_ep->repeat = 0;
> + sch_ep->pkts = 1; /* at most one packet for each microframe */
> + if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
> + sch_ep->cs_count = 3; /* at most need 3 CS*/
> + /* one for SS and one for budgeted transaction */
> + sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
> + sch_ep->bw_cost_per_microframe = max_packet_size;
> + }
> + if (ep_type == ISOC_OUT_EP) {
> + /* must never schedule a cs ISOC OUT ep */
> + sch_ep->cs_count = 0;
> + /*
> + * the best case FS budget assumes that 188 FS bytes
> + * occur in each microframe
> + */
> + sch_ep->num_budget_microframes = DIV_ROUND_UP(
> + sch_ep->max_packet_size, FS_PAYLOAD_MAX);
> + sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
> + }
> + if (ep_type == ISOC_IN_EP) {
> + /* at most need additional two CS. */
> + sch_ep->cs_count = DIV_ROUND_UP(
> + sch_ep->max_packet_size, FS_PAYLOAD_MAX) + 2;
> + sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
> + sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
> + }
> + }
> +}
> +
> +/* Get maximum bandwidth when we schedule at offset slot. */
> +static u32 get_max_bw(struct mu3h_sch_bw_info *sch_bw,
> + struct mu3h_sch_ep_info *sch_ep, u32 offset)
> +{
> + u32 num_esit;
> + u32 max_bw = 0;
> + int i;
> + int j;
> +
> + num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
> + for (i = 0; i < num_esit; i++) {
> + u32 base = offset + i * sch_ep->esit;
> +
> + for (j = 0; j < sch_ep->num_budget_microframes; j++) {
> + if (sch_bw->bus_bw[base + j] > max_bw)
> + max_bw = sch_bw->bus_bw[base + j];
> + }
> + }
> + return max_bw;
> +}
> +
> +static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
> + struct mu3h_sch_ep_info *sch_ep, int bw_cost)
> +{
> + u32 num_esit;
> + u32 base;
> + int i;
> + int j;
> +
> + num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
> + for (i = 0; i < num_esit; i++) {
> + base = sch_ep->offset + i * sch_ep->esit;
> + for (j = 0; j < sch_ep->num_budget_microframes; j++)
> + sch_bw->bus_bw[base + j] += bw_cost;
> + }
> +
> +}
> +
> +static void debug_sch_ep(struct mu3h_sch_ep_info *sch_ep)
> +{
> + pr_debug("%s:\n", __func__);
> + pr_debug("sch_ep->ep_type = %d\n", sch_ep->ep_type);
> + pr_debug("sch_ep->max_packet_size = %d\n", sch_ep->max_packet_size);
> + pr_debug("sch_ep->esit = %d\n", sch_ep->esit);
> + pr_debug("sch_ep->num_budget_microframes = %d\n",
> + sch_ep->num_budget_microframes);
> + pr_debug("sch_ep->bw_cost_per_microframe = %d\n",
> + sch_ep->bw_cost_per_microframe);
> + pr_debug("sch_ep->ep = %p\n", sch_ep->ep);
> + pr_debug("sch_ep->offset = %d\n", sch_ep->offset);
> + pr_debug("sch_ep->repeat = %d\n", sch_ep->repeat);
> + pr_debug("sch_ep->pkts = %d\n", sch_ep->pkts);
> + pr_debug("sch_ep->cs_count = %d\n", sch_ep->cs_count);
> +}
> +
> +static int check_sch_bw(struct usb_device *udev,
> + struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
> +{
> + u32 offset;
> + u32 esit;
> + u32 num_budget_microframes;
> + u32 min_bw;
> + u32 min_index;
> + u32 worst_bw;
> + u32 bw_boundary;
> +
> + if (sch_ep->esit > XHCI_MTK_MAX_ESIT)
> + sch_ep->esit = XHCI_MTK_MAX_ESIT;
> +
> + esit = sch_ep->esit;
> + num_budget_microframes = sch_ep->num_budget_microframes;
> +
> + /*
> + * Search through all possible schedule microframes.
> + * and find a microframe where its worst bandwidth is minimum.
> + */
> + min_bw = ~0;
> + min_index = 0;
> + for (offset = 0; offset < esit; offset++) {
> + if ((offset + num_budget_microframes) > sch_ep->esit)
> + break;
> + /*
> + * usb_20 spec section11.18:
> + * must never schedule Start-Split in Y6
> + */
> + if (is_fs_or_ls(udev->speed) && (offset % 8 == 6))
> + continue;
> +
> + worst_bw = get_max_bw(sch_bw, sch_ep, offset);
> + if (min_bw > worst_bw) {
> + min_bw = worst_bw;
> + min_index = offset;
> + }
> + if (min_bw == 0)
> + break;
> + }
> + sch_ep->offset = min_index;
> +
> + debug_sch_ep(sch_ep);
> +
> + bw_boundary = (udev->speed == USB_SPEED_SUPER)
> + ? SS_BW_BOUNDARY : HS_BW_BOUNDARY;
> +
> + /* check bandwidth */
> + if (min_bw + sch_ep->bw_cost_per_microframe > bw_boundary)
> + return -1;
> +
> + /* update bus bandwidth info */
> + update_bus_bw(sch_bw, sch_ep, sch_ep->bw_cost_per_microframe);
> +
> + return 0;
> +}
> +
> +static void debug_sch_bw(struct mu3h_sch_bw_info *sch_bw)
> +{
> + int i;
> +
> + pr_debug("%s: bus_bw_info\n", __func__);
> + for (i = 0; i < XHCI_MTK_MAX_ESIT; i++)
> + pr_debug("%d ", sch_bw->bus_bw[i]);
> +
> + pr_debug("\n");
> +}
> +
> +
> +static bool need_bw_sch(struct usb_host_endpoint *ep,
> + enum usb_device_speed speed, int has_tt)
> +{
> + /* only for periodic endpoints */
> + if (usb_endpoint_xfer_control(&ep->desc)
> + || usb_endpoint_xfer_bulk(&ep->desc))
> + return false;
> + /*
> + * for LS & FS periodic endpoints which its device don't attach
> + * to TT are also ignored, root-hub will schedule them directly
> + */
> + if (is_fs_or_ls(speed) && !has_tt)
> + return false;
> +
> + return true;
> +}
> +
> +static int xhci_mtk_sch_init(struct xhci_hcd *xhci)
> +{
> + struct usb_hcd *hcd = xhci_to_hcd(xhci);
> + struct device *dev = hcd->self.controller;
> + struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
> + struct mu3h_sch_bw_info *sch_array;
> + int num_usb_bus;
> + int i;
> +
> + /* ss IN and OUT are separated */
> + num_usb_bus = xhci->num_usb3_ports * 2 + xhci->num_usb2_ports;
> +
> + sch_array = kcalloc(num_usb_bus, sizeof(*sch_array), GFP_KERNEL);
> + if (sch_array == NULL)
> + return -ENOMEM;
> +
> + for (i = 0; i < num_usb_bus; i++)
> + INIT_LIST_HEAD(&sch_array[i].bw_ep_list);
> +
> + mtk->sch_array = sch_array;
> +
> + return 0;
> +}
> +
> +
> +static void xhci_mtk_sch_exit(struct xhci_hcd *xhci)
> +{
> + struct usb_hcd *hcd = xhci_to_hcd(xhci);
> + struct device *dev = hcd->self.controller;
> + struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
> +
> + kfree(mtk->sch_array);
> +}
> +
> +
> +int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
> + struct usb_host_endpoint *ep)
> +{
> + struct device *dev = hcd->self.controller;
> + struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
> +
> + int ret = 0;
> + int port_id;
> + int bw_index;
> + struct xhci_hcd *xhci;
> + unsigned int ep_index;
> + struct xhci_ep_ctx *ep_ctx;
> + struct xhci_slot_ctx *slot_ctx;
> + struct xhci_virt_device *virt_dev;
> + struct mu3h_sch_bw_info *sch_bw;
> + struct mu3h_sch_ep_info *sch_ep;
> + struct mu3h_sch_bw_info *sch_array;
> +
> + xhci = hcd_to_xhci(hcd);
> + virt_dev = xhci->devs[udev->slot_id];
> + ep_index = xhci_get_endpoint_index(&ep->desc);
> + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
> + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
> + sch_array = mtk->sch_array;
> +
> + port_id = virt_dev->real_port;
> + xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
> + usb_endpoint_type(&ep->desc), udev->speed, ep);
> +
> + if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
> + return 0;
> +
> + bw_index = get_bw_index(xhci, udev, ep);
> + sch_bw = &sch_array[bw_index];
> +
> + sch_ep = kzalloc(sizeof(struct mu3h_sch_ep_info), GFP_NOIO);
> + if (!sch_ep)
> + return -ENOMEM;
> +
> + setup_sch_info(udev, ep_ctx, sch_ep);
> +
> + ret = check_sch_bw(udev, sch_bw, sch_ep);
> + if (ret) {
> + xhci_err(xhci, "Not enough bandwidth!\n");
> + kfree(sch_ep);
> + return -ENOSPC;
> + }
> +
> + list_add_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
> + sch_ep->ep = ep;
> +
> + ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(sch_ep->pkts)
> + | EP_BCSCOUNT(sch_ep->cs_count) | EP_BBM(sch_ep->burst_mode));
> + ep_ctx->reserved[1] |= cpu_to_le32(EP_BOFFSET(sch_ep->offset)
> + | EP_BREPEAT(sch_ep->repeat));
> +
> + debug_sch_bw(sch_bw);
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(xhci_mtk_add_ep_quirk);
> +
> +
> +void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
> + struct usb_host_endpoint *ep)
> +{
> + struct device *dev = hcd->self.controller;
> + struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
> +
> + int bw_index;
> + struct xhci_hcd *xhci;
> + struct xhci_slot_ctx *slot_ctx;
> + struct xhci_virt_device *virt_dev;
> + struct mu3h_sch_bw_info *sch_array;
> + struct mu3h_sch_bw_info *sch_bw;
> + struct mu3h_sch_ep_info *sch_ep;
> +
> + xhci = hcd_to_xhci(hcd);
> + virt_dev = xhci->devs[udev->slot_id];
> + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
> + sch_array = mtk->sch_array;
> +
> + xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
> + usb_endpoint_type(&ep->desc), udev->speed, ep);
> +
> + if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
> + return;
> +
> + bw_index = get_bw_index(xhci, udev, ep);
> + sch_bw = &sch_array[bw_index];
> +
> + list_for_each_entry(sch_ep, &sch_bw->bw_ep_list, endpoint) {
> + if (sch_ep->ep == ep) {
> + update_bus_bw(sch_bw, sch_ep,
> + -sch_ep->bw_cost_per_microframe);
> + list_del(&sch_ep->endpoint);
> + kfree(sch_ep);
> + break;
> + }
> + }
> + debug_sch_bw(sch_bw);
> +}
> +EXPORT_SYMBOL_GPL(xhci_mtk_drop_ep_quirk);
> +
> +
> +/*
> + * The TD size is the number of max packet sized packets remaining in the TD
> + * (including this TRB), right shifted by 10.
> + * It must fit in bits 21:17, so it can't be bigger than 31.
> + */
> +u32 xhci_mtk_td_remainder_quirk(unsigned int td_running_total,
> + unsigned trb_buffer_length, struct urb *urb)
> +{
> + u32 max = 31;
> + int remainder, td_packet_count, packet_transferred;
> + unsigned int td_transfer_size = urb->transfer_buffer_length;
> + unsigned int maxp;
> +
> + maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
> +
> + /* 0 for the last TRB */
> + if (td_running_total + trb_buffer_length == td_transfer_size)
> + return 0;
> +
> + packet_transferred = td_running_total / maxp;
> + td_packet_count = DIV_ROUND_UP(td_transfer_size, maxp);
> + remainder = td_packet_count - packet_transferred;
> +
> + if (remainder > max)
> + return max << 17;
> + else
> + return remainder << 17;
> +}
> +EXPORT_SYMBOL_GPL(xhci_mtk_td_remainder_quirk);
> +
> +
> +static int xhci_mtk_setup(struct usb_hcd *hcd);
> +static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
> + .extra_priv_size = sizeof(struct xhci_hcd),
> + .reset = xhci_mtk_setup,
> +};
> +
> +static struct hc_driver __read_mostly xhci_mtk_hc_driver;
> +
> +
> +static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk)
> +{
> + int ret;
> +
> + ret = regulator_enable(mtk->vbus);
> + if (ret) {
> + dev_err(mtk->dev, "failed to enable vbus\n");
> + return ret;
> + }
> +
> + ret = regulator_enable(mtk->vusb33);
> + if (ret) {
> + dev_err(mtk->dev, "failed to enable vusb33\n");
> + regulator_disable(mtk->vbus);
> + return ret;
> + }
> + return 0;
> +}
> +
> +static void xhci_mtk_ldos_disable(struct xhci_hcd_mtk *mtk)
> +{
> + regulator_disable(mtk->vbus);
> + regulator_disable(mtk->vusb33);
> +}
> +
> +static void xhci_mtk_quirks(struct device *dev, struct xhci_hcd *xhci)
> +{
> + /*
> + * As of now platform drivers don't provide MSI support so we ensure
> + * here that the generic code does not try to make a pci_dev from our
> + * dev struct in order to setup MSI
> + */
> + xhci->quirks |= XHCI_PLAT;
> + xhci->quirks |= XHCI_MTK_HOST;
> + /*
> + * MTK host controller gives a spurious successful event after a
> + * short transfer. Ignore it.
> + */
> + xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
> +}
> +
> +/* called during probe() after chip reset completes */
> +static int xhci_mtk_setup(struct usb_hcd *hcd)
> +{
> + struct xhci_hcd *xhci;
> + int ret;
> +
> + ret = xhci_gen_setup(hcd, xhci_mtk_quirks);
> + if (ret)
> + return ret;
> +
> + if (!usb_hcd_is_primary_hcd(hcd))
> + return 0;
> +
> + xhci = hcd_to_xhci(hcd);
> + ret = xhci_mtk_sch_init(xhci);
> + if (ret) {
> + kfree(xhci);
> + return ret;
> + }
> +
> + return ret;
> +}
> +
> +
> +static int xhci_mtk_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *node = pdev->dev.of_node;
> + struct usb_xhci_pdata *pdata = dev_get_platdata(dev);
> + struct xhci_hcd_mtk *mtk;
> + const struct hc_driver *driver;
> + struct xhci_hcd *xhci;
> + struct resource *res;
> + struct usb_hcd *hcd;
> + int ret = -ENODEV;
> + int irq;
> +
> + if (usb_disabled())
> + return -ENODEV;
> +
> + driver = &xhci_mtk_hc_driver;
> + mtk = devm_kzalloc(dev, sizeof(*mtk), GFP_KERNEL);
> + if (!mtk)
> + return -ENOMEM;
> + mtk->dev = dev;
> +
> + mtk->sys_mac = devm_clk_get(dev, "sys_mac");
> + if (IS_ERR(mtk->sys_mac)) {
> + dev_err(dev, "error to get sys_mac\n");
> + ret = PTR_ERR(mtk->sys_mac);
> + goto err;
> + }
> +
> + mtk->vbus = devm_regulator_get(dev, "reg-vbus");
> + if (IS_ERR(mtk->vbus)) {
> + dev_err(dev, "fail to get vbus\n");
> + ret = PTR_ERR(mtk->vbus);
> + goto err;
> + }
> +
> + mtk->vusb33 = devm_regulator_get(dev, "reg-vusb33");
> + if (IS_ERR(mtk->vusb33)) {
> + dev_err(dev, "fail to get vusb33\n");
> + ret = PTR_ERR(mtk->vusb33);
> + goto err;
> + }
> + pm_runtime_enable(dev);
> + pm_runtime_get_sync(dev);
> +
> + ret = xhci_mtk_ldos_enable(mtk);
> + if (ret)
> + goto disable_pm;
> +
> + ret = clk_prepare_enable(mtk->sys_mac);
> + if (ret)
> + goto disable_ldos;
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0)
> + goto disable_clk;
> +
> + /* Initialize dma_mask and coherent_dma_mask to 32-bits */
> + ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
> + if (ret)
> + goto disable_clk;
> +
> + if (!dev->dma_mask)
> + dev->dma_mask = &dev->coherent_dma_mask;
> + else
> + dma_set_mask(dev, DMA_BIT_MASK(32));
> +
> + hcd = usb_create_hcd(driver, dev, dev_name(dev));
> + if (!hcd) {
> + ret = -ENOMEM;
> + goto disable_clk;
> + }
> +
> + /*
> + * USB 2.0 roothub is stored in the platform_device.
> + * Swap it with mtk HCD.
> + */
> + mtk->hcd = platform_get_drvdata(pdev);
> + platform_set_drvdata(pdev, mtk);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + hcd->regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(hcd->regs)) {
> + ret = PTR_ERR(hcd->regs);
> + goto put_usb2_hcd;
> + }
> + hcd->rsrc_start = res->start;
> + hcd->rsrc_len = resource_size(res);
> +
> + hcd->usb_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 0);
> + if (IS_ERR(hcd->usb_phy)) {
> + ret = PTR_ERR(hcd->usb_phy);
> + if (ret == -EPROBE_DEFER)
> + goto put_usb2_hcd;
> + hcd->usb_phy = NULL;
> + } else {
> + ret = usb_phy_init(hcd->usb_phy);
> + if (ret)
> + goto put_usb2_hcd;
> + }
> +
> + device_wakeup_enable(hcd->self.controller);
> +
> + xhci = hcd_to_xhci(hcd);
> + xhci->main_hcd = hcd;
> + xhci->shared_hcd = usb_create_shared_hcd(driver, dev,
> + dev_name(dev), hcd);
> + if (!xhci->shared_hcd) {
> + ret = -ENOMEM;
> + goto disable_usb_phy;
> + }
> +
> + if ((node && of_property_read_bool(node, "usb3-lpm-capable")) ||
> + (pdata && pdata->usb3_lpm_capable))
> + xhci->quirks |= XHCI_LPM_SUPPORT;
> +
> + if (HCC_MAX_PSA(xhci->hcc_params) >= 4)
> + xhci->shared_hcd->can_do_streams = 1;
> +
> + ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
> + if (ret)
> + goto put_usb3_hcd;
> +
> + ret = usb_add_hcd(xhci->shared_hcd, irq, IRQF_SHARED);
> + if (ret)
> + goto dealloc_usb2_hcd;
> +
> + return 0;
> +
> +
> +dealloc_usb2_hcd:
> + usb_remove_hcd(hcd);
> +
> +put_usb3_hcd:
> + usb_put_hcd(xhci->shared_hcd);
> +
> +disable_usb_phy:
> + usb_phy_shutdown(hcd->usb_phy);
> +
> +put_usb2_hcd:
> + usb_put_hcd(hcd);
> +
> +disable_clk:
> + clk_disable_unprepare(mtk->sys_mac);
> +
> +disable_ldos:
> + xhci_mtk_ldos_disable(mtk);
> +
> +disable_pm:
> + pm_runtime_put_sync(dev);
> + pm_runtime_disable(dev);
> +
> +err:
> + return ret;
> +}
> +
> +static int xhci_mtk_remove(struct platform_device *dev)
> +{
> + struct xhci_hcd_mtk *mtk = platform_get_drvdata(dev);
> + struct usb_hcd *hcd = mtk->hcd;
> + struct xhci_hcd *xhci = hcd_to_xhci(hcd);
> +
> + usb_remove_hcd(xhci->shared_hcd);
> + usb_phy_shutdown(hcd->usb_phy);
> +
> + usb_remove_hcd(hcd);
> + usb_put_hcd(xhci->shared_hcd);
> + usb_put_hcd(hcd);
> + xhci_mtk_sch_exit(xhci);
> + clk_disable_unprepare(mtk->sys_mac);
> + xhci_mtk_ldos_disable(mtk);
> + pm_runtime_put_sync(&dev->dev);
> + pm_runtime_disable(&dev->dev);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int xhci_mtk_suspend(struct device *dev)
> +{
> + struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
> + struct usb_hcd *hcd = mtk->hcd;
> + int ret;
> +
> + ret = usb_phy_set_suspend(hcd->usb_phy, 1);
> + /* keep on power of mac to maintain register, and only close clock */
> + clk_disable_unprepare(mtk->sys_mac);
> + return ret;
> +}
> +
> +static int xhci_mtk_resume(struct device *dev)
> +{
> + struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
> + struct usb_hcd *hcd = mtk->hcd;
> + int ret;
> +
> + clk_prepare_enable(mtk->sys_mac);
> + ret = usb_phy_set_suspend(hcd->usb_phy, 0);
> +
> + return ret;
> +}
> +
> +static const struct dev_pm_ops xhci_mtk_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(xhci_mtk_suspend, xhci_mtk_resume)
> +};
> +#define DEV_PM_OPS (&xhci_mtk_pm_ops)
> +#else
> +#define DEV_PM_OPS NULL
> +#endif /* CONFIG_PM */
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id mtk_xhci_of_match[] = {
> + { .compatible = "mediatek,mt8173-xhci"},
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, mtk_xhci_of_match);
> +#endif
> +
> +static struct platform_driver mtk_xhci_driver = {
> + .probe = xhci_mtk_probe,
> + .remove = xhci_mtk_remove,
> + .driver = {
> + .name = "xhci-mtk",
> + .pm = DEV_PM_OPS,
> + .of_match_table = of_match_ptr(mtk_xhci_of_match),
> + },
> +};
> +
> +static int __init xhci_mtk_init(void)
> +{
> + xhci_init_driver(&xhci_mtk_hc_driver, &xhci_mtk_overrides);
> + return platform_driver_register(&mtk_xhci_driver);
> +}
> +module_init(xhci_mtk_init);
> +
> +static void __exit xhci_mtk_exit(void)
> +{
> + platform_driver_unregister(&mtk_xhci_driver);
> +}
> +module_exit(xhci_mtk_exit);
> +
> +MODULE_DESCRIPTION("MediaTek xHCI Host Controller Driver");
> +MODULE_LICENSE("GPL v2");
> +
> diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
> new file mode 100644
> index 0000000..e0fdd19
> --- /dev/null
> +++ b/drivers/usb/host/xhci-mtk.h
> @@ -0,0 +1,108 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author:
> + * Zhigang.Wei <zhigang.wei@...iatek.com>
> + * Chunfeng.Yun <chunfeng.yun@...iatek.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#ifndef _XHCI_MTK_H_
> +#define _XHCI_MTK_H_
> +
> +#include "xhci.h"
> +
> +/**
> + * To simplify scheduler algorithm, set a upper limit for ESIT,
> + * if a synchromous ep's ESIT is larger than @XHCI_MTK_MAX_ESIT,
> + * round down to the limit value, that means allocating more
> + * bandwidth to it.
> + */
> +#define XHCI_MTK_MAX_ESIT 64
> +
> +/**
> + * struct mu3h_sch_bw_info
> + * @bus_bw: array to keep track of bandwidth already used at each uframes
> + * @bw_ep_list: eps in the bandwidth domain
> + *
> + * treat a HS root port as a bandwidth domain, but treat a SS root port as
> + * two bandwidth domains, one for IN eps and another for OUT eps.
> + */
> +struct mu3h_sch_bw_info {
> + u32 bus_bw[XHCI_MTK_MAX_ESIT];
> + struct list_head bw_ep_list;
> +};
> +
> +/**
> + * struct mu3h_sch_ep_info
> + * @esit: unit is 125us, equal to 2 << Interval field in ep-context
> + * @num_budget_microframes: number of continuous uframes
> + * (@repeat==1) scheduled within the interval
> + * @ep: address of usb_host_endpoint
> + * @offset: which uframe of the interval that transfer should be
> + * scheduled first time within the interval
> + * @repeat: the time gap between two uframes that transfers are
> + * scheduled within a interval. in the simple algorithm, only
> + * assign 0 or 1 to it; 0 means using only one uframe in a
> + * interval, and1 means using @num_budget_microframes
> + * continuous uframes
> + * @pkts: number of packets to be transferred in the scheduled uframes
> + * @cs_count: number of CS that host will trigger
> + */
> +struct mu3h_sch_ep_info {
> + u32 ep_type;
> + u32 max_packet_size;
> + u32 esit;
> + u32 num_budget_microframes;
> + u32 bw_cost_per_microframe;
> + void *ep;
> + struct list_head endpoint;
> +
> + /* mtk xhci scheduling info */
> + u32 offset;
> + u32 repeat;
> + u32 pkts;
> + u32 cs_count;
> + u32 burst_mode;
> +};
> +
> +
> +#if IS_ENABLED(CONFIG_USB_XHCI_MTK)
> +
> +int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
> + struct usb_host_endpoint *ep);
> +void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
> + struct usb_host_endpoint *ep);
> +u32 xhci_mtk_td_remainder_quirk(unsigned int td_running_total,
> + unsigned trb_buffer_length, struct urb *urb);
> +
> +#else
> +static inline int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd,
> + struct usb_device *udev, struct usb_host_endpoint *ep)
> +{
> + return 0;
> +}
> +
> +static inline void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd,
> + struct usb_device *udev, struct usb_host_endpoint *ep)
> +{
> + return 0;
> +}
> +
> +static inline u32 xhci_mtk_td_remainder_quirk(unsigned int td_running_total,
> + unsigned trb_buffer_length, struct urb *urb)
> +{
> + return 0;
> +}
> +
> +#endif
> +
> +#endif /* _XHCI_MTK_H_ */
> diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
> index 94416ff..73997a0 100644
> --- a/drivers/usb/host/xhci-ring.c
> +++ b/drivers/usb/host/xhci-ring.c
> @@ -68,6 +68,7 @@
> #include <linux/slab.h>
> #include "xhci.h"
> #include "xhci-trace.h"
> +#include "xhci-mtk.h"
>
> /*
> * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
> @@ -3131,9 +3132,14 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
>
> /* Set the TRB length, TD size, and interrupter fields. */
> if (xhci->hci_version < 0x100) {
> - remainder = xhci_td_remainder(
> + if (xhci->quirks & XHCI_MTK_HOST) {
> + remainder = xhci_mtk_td_remainder_quirk(
> + running_total, trb_buff_len, urb);
> + } else {
> + remainder = xhci_td_remainder(
> urb->transfer_buffer_length -
> running_total);
> + }
> } else {
> remainder = xhci_v1_0_td_remainder(running_total,
> trb_buff_len, total_packet_count, urb,
> @@ -3286,9 +3292,14 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
>
> /* Set the TRB length, TD size, and interrupter fields. */
> if (xhci->hci_version < 0x100) {
> - remainder = xhci_td_remainder(
> + if (xhci->quirks & XHCI_MTK_HOST) {
> + remainder = xhci_mtk_td_remainder_quirk(
> + running_total, trb_buff_len, urb);
> + } else {
> + remainder = xhci_td_remainder(
> urb->transfer_buffer_length -
> running_total);
> + }
> } else {
> remainder = xhci_v1_0_td_remainder(running_total,
> trb_buff_len, total_packet_count, urb,
> @@ -3383,7 +3394,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
> field |= 0x1;
>
> /* xHCI 1.0 6.4.1.2.1: Transfer Type field */
> - if (xhci->hci_version == 0x100) {
> + if ((xhci->hci_version == 0x100) || (xhci->quirks & XHCI_MTK_HOST)) {
> if (urb->transfer_buffer_length > 0) {
> if (setup->bRequestType & USB_DIR_IN)
> field |= TRB_TX_TYPE(TRB_DATA_IN);
> @@ -3407,8 +3418,14 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
> field = TRB_TYPE(TRB_DATA);
>
> length_field = TRB_LEN(urb->transfer_buffer_length) |
> - xhci_td_remainder(urb->transfer_buffer_length) |
> TRB_INTR_TARGET(0);
> +
> + if (xhci->quirks & XHCI_MTK_HOST)
> + length_field |= xhci_mtk_td_remainder_quirk(0,
> + urb->transfer_buffer_length, urb);
> + else
> + length_field |= xhci_td_remainder(urb->transfer_buffer_length);
> +
> if (urb->transfer_buffer_length > 0) {
> if (setup->bRequestType & USB_DIR_IN)
> field |= TRB_DIR_IN;
> @@ -3632,8 +3649,14 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
>
> /* Set the TRB length, TD size, & interrupter fields. */
> if (xhci->hci_version < 0x100) {
> - remainder = xhci_td_remainder(
> - td_len - running_total);
> + if (xhci->quirks & XHCI_MTK_HOST) {
> + remainder = xhci_mtk_td_remainder_quirk(
> + running_total, trb_buff_len,
> + urb);
> + } else {
> + remainder = xhci_td_remainder(
> + td_len - running_total);
> + }
> } else {
> remainder = xhci_v1_0_td_remainder(
> running_total, trb_buff_len,
> diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
> index 7da0d60..209fc8a 100644
> --- a/drivers/usb/host/xhci.c
> +++ b/drivers/usb/host/xhci.c
> @@ -31,6 +31,7 @@
>
> #include "xhci.h"
> #include "xhci-trace.h"
> +#include "xhci-mtk.h"
>
> #define DRIVER_AUTHOR "Sarah Sharp"
> #define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
> @@ -623,7 +624,11 @@ int xhci_run(struct usb_hcd *hcd)
> "// Set the interrupt modulation register");
> temp = readl(&xhci->ir_set->irq_control);
> temp &= ~ER_IRQ_INTERVAL_MASK;
> - temp |= (u32) 160;
> + /*
> + * the increment interval is 8 times as much as that defined
> + * in xHCI spec on MTK's controller
> + */
> + temp |= (u32) ((xhci->quirks & XHCI_MTK_HOST) ? 20 : 160);
> writel(temp, &xhci->ir_set->irq_control);
>
> /* Set the HCD state before we enable the irqs */
> @@ -1688,6 +1693,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
>
> xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
>
> + if (xhci->quirks & XHCI_MTK_HOST)
> + xhci_mtk_drop_ep_quirk(hcd, udev, ep);
> +
> xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
> (unsigned int) ep->desc.bEndpointAddress,
> udev->slot_id,
> @@ -1783,6 +1791,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
> return -ENOMEM;
> }
>
> + if (xhci->quirks & XHCI_MTK_HOST) {
> + ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
> + if (ret < 0) {
> + xhci_free_or_cache_endpoint_ring(xhci,
> + virt_dev, ep_index);
> + return ret;
> + }
> + }
> +
> ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
> new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
>
> diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
> index 31e46cc..d257ce3 100644
> --- a/drivers/usb/host/xhci.h
> +++ b/drivers/usb/host/xhci.h
> @@ -1567,6 +1567,7 @@ struct xhci_hcd {
> /* For controllers with a broken beyond repair streams implementation */
> #define XHCI_BROKEN_STREAMS (1 << 19)
> #define XHCI_PME_STUCK_QUIRK (1 << 20)
> +#define XHCI_MTK_HOST (1 << 21)
> unsigned int num_active_eps;
> unsigned int limit_active_eps;
> /* There are two roothubs to keep track of bus suspend info for */
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists