[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <1438361581-2702-4-git-send-email-stefan@agner.ch>
Date: Fri, 31 Jul 2015 18:52:59 +0200
From: Stefan Agner <stefan@...er.ch>
To: dwmw2@...radead.org, computersforpeace@...il.com
Cc: sebastian@...akpoint.cc, robh+dt@...nel.org, pawel.moll@....com,
mark.rutland@....com, ijc+devicetree@...lion.org.uk,
galak@...eaurora.org, shawn.guo@...aro.org, kernel@...gutronix.de,
boris.brezillon@...e-electrons.com, marb@...at.de,
aaron@...tycactus.com, bpringlemeir@...il.com,
linux-mtd@...ts.infradead.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
albert.aribaud@...ev.fr, Stefan Agner <stefan@...er.ch>,
Bill Pringlemeir <bpringlemeir@...ps.com>
Subject: [PATCH v9 3/5] mtd: nand: vf610_nfc: add device tree bindings
Signed-off-by: Bill Pringlemeir <bpringlemeir@...ps.com>
Signed-off-by: Stefan Agner <stefan@...er.ch>
---
.../devicetree/bindings/mtd/vf610-nfc.txt | 45 ++++++++++++++++++++++
1 file changed, 45 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mtd/vf610-nfc.txt
diff --git a/Documentation/devicetree/bindings/mtd/vf610-nfc.txt b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
new file mode 100644
index 0000000..cae5f25
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
@@ -0,0 +1,45 @@
+Freescale's NAND flash controller (NFC)
+
+This variant of the Freescale NAND flash controller (NFC) can be found on
+Vybrid (vf610), MPC5125, MCF54418 and Kinetis K70.
+
+Required properties:
+- compatible: Should be set to "fsl,vf610-nfc"
+- reg: address range of the NFC
+- interrupts: interrupt of the NFC
+- nand-bus-width: see nand.txt
+- nand-ecc-mode: see nand.txt
+- nand-on-flash-bbt: see nand.txt
+- assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>;
+- assigned-clock-rates: The NAND bus timing is derived from this clock
+ rate and should not exceed maximum timing for any NAND memory chip
+ in a board stuffing. Typical NAND memory timings derived from this
+ clock are found in the SoC hardware reference manual. Furthermore,
+ there might be restrictions on maximum rates when using hardware ECC.
+
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+ representing partitions.
+
+Required properties for hardware ECC:
+- nand-ecc-strength: supported strengths are 24 and 32 bit (see nand.txt)
+- nand-ecc-step-size: step size equals page size, currently only 2k pages are
+ supported
+
+Example:
+
+ nfc: nand@...e0000 {
+ compatible = "fsl,vf610-nfc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x400e0000 0x4000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks VF610_CLK_NFC>;
+ clock-names = "nfc";
+ assigned-clocks = <&clks VF610_CLK_NFC>;
+ assigned-clock-rates = <33000000>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <32>;
+ nand-ecc-step-size = <2048>;
+ nand-on-flash-bbt;
+ };
--
2.4.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists