[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <1438938752-31010-22-git-send-email-rogerq@ti.com>
Date: Fri, 7 Aug 2015 12:12:31 +0300
From: Roger Quadros <rogerq@...com>
To: <tony@...mide.com>
CC: <dwmw2@...radead.org>, <computersforpeace@...il.com>,
<ezequiel@...guardiasur.com.ar>, <javier@...hile0.org>,
<fcooper@...com>, <nsekhar@...com>,
<linux-mtd@...ts.infradead.org>, <linux-omap@...r.kernel.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
Roger Quadros <rogerq@...com>
Subject: [PATCH v2 21/22] ARM: dts: dra7x-evm: Provide NAND ready pin
On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.
Read speed increases from 13768 KiB/ to 17246 KiB/s.
Write speed was unchanged at 7123 KiB/s.
Measured using mtd_speedtest.ko.
Signed-off-by: Roger Quadros <rogerq@...com>
---
arch/arm/boot/dts/dra7-evm.dts | 1 +
arch/arm/boot/dts/dra72-evm.dts | 1 +
2 files changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 3fb1ced..b717fd0 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -575,6 +575,7 @@
reg = <0 0 4>; /* device IO registers */
interrupt-parent = <&crossbar_mpu>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ ready-gpio = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <16>;
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index fc0677a..c1a3397 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -387,6 +387,7 @@
*/
reg = <0 0 4>; /* device IO registers */
interrupt-parent = <&crossbar_mpu>;
+ ready-gpio = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <16>;
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists