| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20150809064752.GV19600@pengutronix.de>
Date: Sun, 9 Aug 2015 08:47:52 +0200
From: Markus Pargmann <mpa@...gutronix.de>
To: Jonathan Cameron <jic23@...nel.org>
Cc: Vlad Dogaru <vlad.dogaru@...el.com>,
Paul Bolle <pebolle@...cali.nl>, linux-iio@...r.kernel.org,
linux-kernel@...r.kernel.org, kernel@...gutronix.de,
Srinivas Pandruvada <srinivas.pandruvada@...ux.intel.com>
Subject: Re: [PATCH v2 1/6] iio: bmg160: Use i2c regmap instead of direct i2c
access
On Tue, Aug 04, 2015 at 01:02:54PM +0200, Markus Pargmann wrote:
> This patch introduces regmap usage into the driver. This is done to
> later easily support the SPI interface of this chip.
>
> Signed-off-by: Markus Pargmann <mpa@...gutronix.de>
> ---
> drivers/iio/gyro/Kconfig | 2 +
> drivers/iio/gyro/bmg160.c | 200 +++++++++++++++++++++-------------------------
> 2 files changed, 91 insertions(+), 111 deletions(-)
>
> diff --git a/drivers/iio/gyro/Kconfig b/drivers/iio/gyro/Kconfig
> index 8d2439345673..b44984b3bb24 100644
> --- a/drivers/iio/gyro/Kconfig
> +++ b/drivers/iio/gyro/Kconfig
> @@ -55,6 +55,8 @@ config BMG160
> depends on I2C
> select IIO_BUFFER
> select IIO_TRIGGERED_BUFFER
> + select REGMAP
> + select REGMAP_I2C
> help
> Say yes here to build support for Bosch BMG160 Tri-axis Gyro Sensor
> driver. This driver also supports BMI055 gyroscope.
> diff --git a/drivers/iio/gyro/bmg160.c b/drivers/iio/gyro/bmg160.c
> index 460bf715d541..626f5c98dde8 100644
> --- a/drivers/iio/gyro/bmg160.c
> +++ b/drivers/iio/gyro/bmg160.c
> @@ -28,6 +28,7 @@
> #include <linux/iio/events.h>
> #include <linux/iio/trigger_consumer.h>
> #include <linux/iio/triggered_buffer.h>
> +#include <linux/regmap.h>
>
> #define BMG160_DRV_NAME "bmg160"
> #define BMG160_IRQ_NAME "bmg160_event"
> @@ -98,6 +99,7 @@
>
> struct bmg160_data {
> struct i2c_client *client;
> + struct regmap *regmap;
> struct iio_trigger *dready_trig;
> struct iio_trigger *motion_trig;
> struct mutex mutex;
> @@ -134,12 +136,19 @@ static const struct {
> { 133, BMG160_RANGE_250DPS},
> { 66, BMG160_RANGE_125DPS} };
>
> +struct regmap_config bmg160_regmap_i2c_conf = {
> + .reg_bits = 8,
> + .val_bits = 8,
> +
> + .use_single_rw = true,
This should not be necessary, we should be able to read multiple
registers at once. This is the same for the spi regmap config.
Also a max_register is missing. Will fix it.
Regards,
Markus
> + .cache_type = REGCACHE_NONE,
> +};
> +
> static int bmg160_set_mode(struct bmg160_data *data, u8 mode)
> {
> int ret;
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_PMU_LPW, mode);
> + ret = regmap_write(data->regmap, BMG160_REG_PMU_LPW, mode);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_pmu_lpw\n");
> return ret;
> @@ -169,8 +178,7 @@ static int bmg160_set_bw(struct bmg160_data *data, int val)
> if (bw_bits < 0)
> return bw_bits;
>
> - ret = i2c_smbus_write_byte_data(data->client, BMG160_REG_PMU_BW,
> - bw_bits);
> + ret = regmap_write(data->regmap, BMG160_REG_PMU_BW, bw_bits);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_pmu_bw\n");
> return ret;
> @@ -184,16 +192,17 @@ static int bmg160_set_bw(struct bmg160_data *data, int val)
> static int bmg160_chip_init(struct bmg160_data *data)
> {
> int ret;
> + unsigned int val;
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_CHIP_ID);
> + ret = regmap_read(data->regmap, BMG160_REG_CHIP_ID, &val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_chip_id\n");
> return ret;
> }
>
> - dev_dbg(&data->client->dev, "Chip Id %x\n", ret);
> - if (ret != BMG160_CHIP_ID_VAL) {
> - dev_err(&data->client->dev, "invalid chip %x\n", ret);
> + dev_dbg(&data->client->dev, "Chip Id %x\n", val);
> + if (val != BMG160_CHIP_ID_VAL) {
> + dev_err(&data->client->dev, "invalid chip %x\n", val);
> return -ENODEV;
> }
>
> @@ -210,40 +219,31 @@ static int bmg160_chip_init(struct bmg160_data *data)
> return ret;
>
> /* Set Default Range */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_RANGE,
> - BMG160_RANGE_500DPS);
> + ret = regmap_write(data->regmap, BMG160_REG_RANGE, BMG160_RANGE_500DPS);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_range\n");
> return ret;
> }
> data->dps_range = BMG160_RANGE_500DPS;
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_SLOPE_THRES);
> + ret = regmap_read(data->regmap, BMG160_REG_SLOPE_THRES, &val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_slope_thres\n");
> return ret;
> }
> - data->slope_thres = ret;
> + data->slope_thres = val;
>
> /* Set default interrupt mode */
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_EN_1);
> - if (ret < 0) {
> - dev_err(&data->client->dev, "Error reading reg_int_en_1\n");
> - return ret;
> - }
> - ret &= ~BMG160_INT1_BIT_OD;
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_1, ret);
> + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_EN_1,
> + BMG160_INT1_BIT_OD, 0);
> if (ret < 0) {
> - dev_err(&data->client->dev, "Error writing reg_int_en_1\n");
> + dev_err(&data->client->dev, "Error updating bits in reg_int_en_1\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_motion_intr\n");
> @@ -284,41 +284,28 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data,
> int ret;
>
> /* Enable/Disable INT_MAP0 mapping */
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_MAP_0);
> - if (ret < 0) {
> - dev_err(&data->client->dev, "Error reading reg_int_map0\n");
> - return ret;
> - }
> - if (status)
> - ret |= BMG160_INT_MAP_0_BIT_ANY;
> - else
> - ret &= ~BMG160_INT_MAP_0_BIT_ANY;
> -
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_MAP_0,
> - ret);
> + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_MAP_0,
> + BMG160_INT_MAP_0_BIT_ANY,
> + (status ? BMG160_INT_MAP_0_BIT_ANY : 0));
> if (ret < 0) {
> - dev_err(&data->client->dev, "Error writing reg_int_map0\n");
> + dev_err(&data->client->dev, "Error updating bits reg_int_map0\n");
> return ret;
> }
>
> /* Enable/Disable slope interrupts */
> if (status) {
> /* Update slope thres */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_SLOPE_THRES,
> - data->slope_thres);
> + ret = regmap_write(data->regmap, BMG160_REG_SLOPE_THRES,
> + data->slope_thres);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_slope_thres\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_MOTION_INTR,
> - BMG160_INT_MOTION_X |
> - BMG160_INT_MOTION_Y |
> - BMG160_INT_MOTION_Z);
> + ret = regmap_write(data->regmap, BMG160_REG_MOTION_INTR,
> + BMG160_INT_MOTION_X | BMG160_INT_MOTION_Y |
> + BMG160_INT_MOTION_Z);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_motion_intr\n");
> @@ -331,10 +318,10 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data,
> * to set latched mode, we will be flooded anyway with INTR
> */
> if (!data->dready_trigger_on) {
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap,
> + BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> @@ -342,14 +329,12 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data,
> }
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - BMG160_DATA_ENABLE_INT);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0,
> + BMG160_DATA_ENABLE_INT);
>
> - } else
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - 0);
> + } else {
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, 0);
> + }
>
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_int_en0\n");
> @@ -365,55 +350,39 @@ static int bmg160_setup_new_data_interrupt(struct bmg160_data *data,
> int ret;
>
> /* Enable/Disable INT_MAP1 mapping */
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_MAP_1);
> - if (ret < 0) {
> - dev_err(&data->client->dev, "Error reading reg_int_map1\n");
> - return ret;
> - }
> -
> - if (status)
> - ret |= BMG160_INT_MAP_1_BIT_NEW_DATA;
> - else
> - ret &= ~BMG160_INT_MAP_1_BIT_NEW_DATA;
> -
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_MAP_1,
> - ret);
> + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_MAP_1,
> + BMG160_INT_MAP_1_BIT_NEW_DATA,
> + (status ? BMG160_INT_MAP_1_BIT_NEW_DATA : 0));
> if (ret < 0) {
> - dev_err(&data->client->dev, "Error writing reg_int_map1\n");
> + dev_err(&data->client->dev, "Error updating bits in reg_int_map1\n");
> return ret;
> }
>
> if (status) {
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_NON_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_NON_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - BMG160_DATA_ENABLE_INT);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0,
> + BMG160_DATA_ENABLE_INT);
>
> } else {
> /* Restore interrupt mode */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - 0);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, 0);
> }
>
> if (ret < 0) {
> @@ -444,10 +413,8 @@ static int bmg160_set_scale(struct bmg160_data *data, int val)
>
> for (i = 0; i < ARRAY_SIZE(bmg160_scale_table); ++i) {
> if (bmg160_scale_table[i].scale == val) {
> - ret = i2c_smbus_write_byte_data(
> - data->client,
> - BMG160_REG_RANGE,
> - bmg160_scale_table[i].dps_range);
> + ret = regmap_write(data->regmap, BMG160_REG_RANGE,
> + bmg160_scale_table[i].dps_range);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_range\n");
> @@ -464,6 +431,7 @@ static int bmg160_set_scale(struct bmg160_data *data, int val)
> static int bmg160_get_temp(struct bmg160_data *data, int *val)
> {
> int ret;
> + unsigned int raw_val;
>
> mutex_lock(&data->mutex);
> ret = bmg160_set_power_state(data, true);
> @@ -472,7 +440,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val)
> return ret;
> }
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_TEMP);
> + ret = regmap_read(data->regmap, BMG160_REG_TEMP, &raw_val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_temp\n");
> bmg160_set_power_state(data, false);
> @@ -480,7 +448,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val)
> return ret;
> }
>
> - *val = sign_extend32(ret, 7);
> + *val = sign_extend32(raw_val, 7);
> ret = bmg160_set_power_state(data, false);
> mutex_unlock(&data->mutex);
> if (ret < 0)
> @@ -492,6 +460,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val)
> static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val)
> {
> int ret;
> + unsigned int raw_val;
>
> mutex_lock(&data->mutex);
> ret = bmg160_set_power_state(data, true);
> @@ -500,7 +469,8 @@ static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val)
> return ret;
> }
>
> - ret = i2c_smbus_read_word_data(data->client, BMG160_AXIS_TO_REG(axis));
> + ret = regmap_bulk_read(data->regmap, BMG160_AXIS_TO_REG(axis), &raw_val,
> + 2);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading axis %d\n", axis);
> bmg160_set_power_state(data, false);
> @@ -508,7 +478,7 @@ static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val)
> return ret;
> }
>
> - *val = sign_extend32(ret, 15);
> + *val = sign_extend32(raw_val, 15);
> ret = bmg160_set_power_state(data, false);
> mutex_unlock(&data->mutex);
> if (ret < 0)
> @@ -807,12 +777,13 @@ static irqreturn_t bmg160_trigger_handler(int irq, void *p)
> struct iio_dev *indio_dev = pf->indio_dev;
> struct bmg160_data *data = iio_priv(indio_dev);
> int bit, ret, i = 0;
> + unsigned int val;
>
> mutex_lock(&data->mutex);
> for_each_set_bit(bit, indio_dev->active_scan_mask,
> indio_dev->masklength) {
> - ret = i2c_smbus_read_word_data(data->client,
> - BMG160_AXIS_TO_REG(bit));
> + ret = regmap_bulk_read(data->regmap, BMG160_AXIS_TO_REG(bit),
> + &val, 2);
> if (ret < 0) {
> mutex_unlock(&data->mutex);
> goto err;
> @@ -840,10 +811,9 @@ static int bmg160_trig_try_reen(struct iio_trigger *trig)
> return 0;
>
> /* Set latched mode interrupt and clear any latched interrupt */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_rst_latch\n");
> return ret;
> @@ -907,33 +877,34 @@ static irqreturn_t bmg160_event_handler(int irq, void *private)
> struct bmg160_data *data = iio_priv(indio_dev);
> int ret;
> int dir;
> + unsigned int val;
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_STATUS_2);
> + ret = regmap_read(data->regmap, BMG160_REG_INT_STATUS_2, &val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_int_status2\n");
> goto ack_intr_status;
> }
>
> - if (ret & 0x08)
> + if (val & 0x08)
> dir = IIO_EV_DIR_RISING;
> else
> dir = IIO_EV_DIR_FALLING;
>
> - if (ret & BMG160_ANY_MOTION_BIT_X)
> + if (val & BMG160_ANY_MOTION_BIT_X)
> iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL,
> 0,
> IIO_MOD_X,
> IIO_EV_TYPE_ROC,
> dir),
> iio_get_time_ns());
> - if (ret & BMG160_ANY_MOTION_BIT_Y)
> + if (val & BMG160_ANY_MOTION_BIT_Y)
> iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL,
> 0,
> IIO_MOD_Y,
> IIO_EV_TYPE_ROC,
> dir),
> iio_get_time_ns());
> - if (ret & BMG160_ANY_MOTION_BIT_Z)
> + if (val & BMG160_ANY_MOTION_BIT_Z)
> iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL,
> 0,
> IIO_MOD_Z,
> @@ -943,10 +914,9 @@ static irqreturn_t bmg160_event_handler(int irq, void *private)
>
> ack_intr_status:
> if (!data->dready_trigger_on) {
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0)
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> @@ -1038,6 +1008,14 @@ static int bmg160_probe(struct i2c_client *client,
> struct iio_dev *indio_dev;
> int ret;
> const char *name = NULL;
> + struct regmap *regmap;
> +
> + regmap = devm_regmap_init_i2c(client, &bmg160_regmap_i2c_conf);
> + if (IS_ERR(regmap)) {
> + dev_err(&client->dev, "Failed to register i2c regmap %d\n",
> + (int)PTR_ERR(regmap));
> + return PTR_ERR(regmap);
> + }
>
> indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> if (!indio_dev)
> --
> 2.1.4
>
>
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Download attachment "signature.asc" of type "application/pgp-signature" (820 bytes)
Powered by blists - more mailing lists