| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <55C93531.9050205@rock-chips.com>
Date: Tue, 11 Aug 2015 07:35:13 +0800
From: Shawn Lin <shawn.lin@...k-chips.com>
To: Alim Akhtar <alim.akhtar@...il.com>
Cc: lintao@...k-chips.com, Jaehoon Chung <jh80.chung@...sung.com>,
Ulf Hansson <ulf.hansson@...aro.org>,
Heiko Stübner <heiko@...ech.de>,
Douglas Anderson <dianders@...omium.org>,
Vineet.Gupta1@...opsys.com, Wei Xu <xuwei5@...ilicon.com>,
Joachim Eastwood <manabian@...il.com>,
Alexey Brodkin <abrodkin@...opsys.com>,
Kukjin Kim <kgene@...nel.org>,
Krzysztof Kozlowski <k.kozlowski@...sung.com>,
Russell King <linux@....linux.org.uk>,
Jun Nie <jun.nie@...aro.org>,
Ralf Baechle <ralf@...ux-mips.org>,
Govindraj Raja <govindraj.raja@...tec.com>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
"linux-samsung-soc@...r.kernel.org"
<linux-samsung-soc@...r.kernel.org>, linux-mips@...ux-mips.org,
"linux-mmc@...r.kernel.org" <linux-mmc@...r.kernel.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"open list:ARM/Rockchip SoC..." <linux-rockchip@...ts.infradead.org>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>
Subject: Re: [RFC PATCH v4 1/9] mmc: dw_mmc: Add external dma interface
support
在 2015/8/11 2:03, Alim Akhtar 写道:
> Hi Shawn
>
> On Thu, Aug 6, 2015 at 12:14 PM, Shawn Lin <shawn.lin@...k-chips.com> wrote:
>> DesignWare MMC Controller can supports two types of DMA
>> mode: external dma and internal dma. We get a RK312x platform
>> integrated dw_mmc and ARM pl330 dma controller. This patch add
>> edmac ops to support these platforms. I've tested it on RK312x
>> platform with edmac mode and RK3288 platform with idmac mode.
>>
> Just curious to know if their are any performance (read/write)
> difference with Idmac and edmac?
>
yes, actually the performance with edmac is worse than that does with
idmac since other peripheral blocks(e.g:I2C/uart/i2s etc.) share generic
DMA with it that means dw_mmc has to compete with them to request the
free channel and be shceduled if generic DMA is busy.
>> Signed-off-by: Shawn Lin <shawn.lin@...k-chips.com>
>>
>> ---
>>
>> Changes in v4:
>> - remove "host->trans_mode" and use "host->use_dma" to indicate
>> transfer mode.
>> - remove all bt-bindings' changes since we don't need new properities.
>> - check transfer mode at runtime by reading HCON reg
>> - spilt defconfig changes for each sub-architecture
>> - fix the title of cover letter
>> - reuse some code for reducing code size
>>
>> Changes in v3:
>> - choose transfer mode at runtime
>> - remove all CONFIG_MMC_DW_IDMAC config option
>> - add supports-idmac property for some platforms
>>
>> Changes in v2:
>> - Fix typo of dev_info msg
>> - remove unused dmach from declaration of dw_mci_dma_slave
>>
>> drivers/mmc/host/Kconfig | 11 +-
>> drivers/mmc/host/dw_mmc-pltfm.c | 2 +
>> drivers/mmc/host/dw_mmc.c | 258 ++++++++++++++++++++++++++++++++--------
>> include/linux/mmc/dw_mmc.h | 27 ++++-
>> 4 files changed, 232 insertions(+), 66 deletions(-)
>>
>> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
>> index 6a0f9c7..a86c0eb 100644
>> --- a/drivers/mmc/host/Kconfig
>> +++ b/drivers/mmc/host/Kconfig
>> @@ -607,15 +607,7 @@ config MMC_DW
>> help
>> This selects support for the Synopsys DesignWare Mobile Storage IP
>> block, this provides host support for SD and MMC interfaces, in both
>> - PIO and external DMA modes.
>> -
>> -config MMC_DW_IDMAC
>> - bool "Internal DMAC interface"
>> - depends on MMC_DW
>> - help
>> - This selects support for the internal DMAC block within the Synopsys
>> - Designware Mobile Storage IP block. This disables the external DMA
>> - interface.
>> + PIO, internal DMA mode and external DMA modes.
>>
>> config MMC_DW_PLTFM
>> tristate "Synopsys Designware MCI Support as platform device"
>> @@ -644,7 +636,6 @@ config MMC_DW_K3
>> tristate "K3 specific extensions for Synopsys DW Memory Card Interface"
>> depends on MMC_DW
>> select MMC_DW_PLTFM
>> - select MMC_DW_IDMAC
>> help
>> This selects support for Hisilicon K3 SoC specific extensions to the
>> Synopsys DesignWare Memory Card Interface driver. Select this option
>> diff --git a/drivers/mmc/host/dw_mmc-pltfm.c b/drivers/mmc/host/dw_mmc-pltfm.c
>> index ec6dbcd..7e1d13b 100644
>> --- a/drivers/mmc/host/dw_mmc-pltfm.c
>> +++ b/drivers/mmc/host/dw_mmc-pltfm.c
>> @@ -59,6 +59,8 @@ int dw_mci_pltfm_register(struct platform_device *pdev,
>> host->pdata = pdev->dev.platform_data;
>>
>> regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + /* Get registers' physical base address */
>> + host->phy_regs = (void *)(regs->start);
>> host->regs = devm_ioremap_resource(&pdev->dev, regs);
>> if (IS_ERR(host->regs))
>> return PTR_ERR(host->regs);
>> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
>> index 40e9d8e..5d6cdff 100644
>> --- a/drivers/mmc/host/dw_mmc.c
>> +++ b/drivers/mmc/host/dw_mmc.c
>> @@ -56,7 +56,7 @@
>> #define DW_MCI_FREQ_MAX 200000000 /* unit: HZ */
>> #define DW_MCI_FREQ_MIN 400000 /* unit: HZ */
>>
>> -#ifdef CONFIG_MMC_DW_IDMAC
>> +
>> #define IDMAC_INT_CLR (SDMMC_IDMAC_INT_AI | SDMMC_IDMAC_INT_NI | \
>> SDMMC_IDMAC_INT_CES | SDMMC_IDMAC_INT_DU | \
>> SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \
>> @@ -99,7 +99,6 @@ struct idmac_desc {
>>
>> __le32 des3; /* buffer 2 physical address */
>> };
>> -#endif /* CONFIG_MMC_DW_IDMAC */
>>
>> static bool dw_mci_reset(struct dw_mci *host);
>> static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset);
>> @@ -403,7 +402,6 @@ static int dw_mci_get_dma_dir(struct mmc_data *data)
>> return DMA_FROM_DEVICE;
>> }
>>
>> -#ifdef CONFIG_MMC_DW_IDMAC
>> static void dw_mci_dma_cleanup(struct dw_mci *host)
>> {
>> struct mmc_data *data = host->data;
>> @@ -441,12 +439,21 @@ static void dw_mci_idmac_stop_dma(struct dw_mci *host)
>> mci_writel(host, BMOD, temp);
>> }
>>
>> -static void dw_mci_idmac_complete_dma(struct dw_mci *host)
>> +static void dw_mci_dmac_complete_dma(void *arg)
>> {
>> + struct dw_mci *host = arg;
>> struct mmc_data *data = host->data;
>>
>> dev_vdbg(host->dev, "DMA complete\n");
>>
>> + if (host->use_dma == TRANS_MODE_EDMAC)
>> + if (data && (data->flags & MMC_DATA_READ))
>> + /* Invalidate cache after read */
>> + dma_sync_sg_for_cpu(mmc_dev(host->cur_slot->mmc),
>> + data->sg,
>> + data->sg_len,
>> + DMA_FROM_DEVICE);
>> +
>> host->dma_ops->cleanup(host);
>>
>> /*
>> @@ -527,7 +534,7 @@ static void dw_mci_translate_sglist(struct dw_mci *host, struct mmc_data *data,
>> wmb();
>> }
>>
>> -static void dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
>> +static int dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
>> {
>> u32 temp;
>>
>> @@ -551,6 +558,8 @@ static void dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
>>
>> /* Start it running */
>> mci_writel(host, PLDMND, 1);
>> +
>> + return 0;
>> }
>>
>> static int dw_mci_idmac_init(struct dw_mci *host)
>> @@ -629,10 +638,112 @@ static const struct dw_mci_dma_ops dw_mci_idmac_ops = {
>> .init = dw_mci_idmac_init,
>> .start = dw_mci_idmac_start_dma,
>> .stop = dw_mci_idmac_stop_dma,
>> - .complete = dw_mci_idmac_complete_dma,
>> + .complete = dw_mci_dmac_complete_dma,
>> + .cleanup = dw_mci_dma_cleanup,
>> +};
>> +
>> +static void dw_mci_edmac_stop_dma(struct dw_mci *host)
>> +{
>> + dmaengine_terminate_all(host->dms->ch);
>> +}
>> +
>> +static int dw_mci_edmac_start_dma(struct dw_mci *host,
>> + unsigned int sg_len)
>> +{
>> + struct dma_slave_config cfg;
>> + struct dma_async_tx_descriptor *desc = NULL;
>> + struct scatterlist *sgl = host->data->sg;
>> + const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
>> + u32 sg_elems = host->data->sg_len;
>> + u32 fifoth_val;
>> + u32 fifo_offset = host->fifo_reg - host->regs;
>> + int ret = 0;
>> +
>> + /* Set external dma config: burst size, burst width */
>> + cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
>> + cfg.src_addr = cfg.dst_addr;
>> + cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
>> + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
>> +
>> + /* Match burst msize with external dma config */
>> + fifoth_val = mci_readl(host, FIFOTH);
>> + cfg.dst_maxburst = mszs[(fifoth_val >> 28) & 0x7];
>> + cfg.src_maxburst = cfg.dst_maxburst;
>> +
>> + if (host->data->flags & MMC_DATA_WRITE)
>> + cfg.direction = DMA_MEM_TO_DEV;
>> + else /* MMC_DATA_READ */
>> + cfg.direction = DMA_DEV_TO_MEM;
>> +
>> + ret = dmaengine_slave_config(host->dms->ch, &cfg);
>> + if (ret) {
>> + dev_err(host->dev, "Failed to config edmac.\n");
>> + return -EBUSY;
>> + }
>> +
>> + desc = dmaengine_prep_slave_sg(host->dms->ch, sgl,
>> + sg_len, cfg.direction,
>> + DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
>> + if (!desc) {
>> + dev_err(host->dev, "Can't prepare slave sg.\n");
>> + return -EBUSY;
>> + }
>> +
>> + /* Set dw_mci_edmac_complete_dma as callback */
>> + desc->callback = dw_mci_dmac_complete_dma;
>> + desc->callback_param = (void *)host;
>> + dmaengine_submit(desc);
>> +
>> + /* Flush cache before write */
>> + if (host->data->flags & MMC_DATA_WRITE)
>> + dma_sync_sg_for_device(mmc_dev(host->cur_slot->mmc), sgl,
>> + sg_elems, DMA_TO_DEVICE);
>> +
>> + dma_async_issue_pending(host->dms->ch);
>> +
>> + return 0;
>> +}
>> +
>> +static int dw_mci_edmac_init(struct dw_mci *host)
>> +{
>> + /* Request external dma channel */
>> + host->dms = kzalloc(sizeof(struct dw_mci_dma_slave), GFP_KERNEL);
>> + if (!host->dms)
>> + return -ENOMEM;
>> +
>> + host->dms->ch = dma_request_slave_channel(host->dev, "rx-tx");
>> + if (!host->dms->ch) {
>> + dev_err(host->dev,
>> + "Failed to get external DMA channel %d\n",
>> + host->dms->ch->chan_id);
>> + kfree(host->dms);
>> + host->dms = NULL;
>> + return -ENXIO;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void dw_mci_edmac_exit(struct dw_mci *host)
>> +{
>> + if (host->dms) {
>> + if (host->dms->ch) {
>> + dma_release_channel(host->dms->ch);
>> + host->dms->ch = NULL;
>> + }
>> + kfree(host->dms);
>> + host->dms = NULL;
>> + }
>> +}
>> +
>> +static const struct dw_mci_dma_ops dw_mci_edmac_ops = {
>> + .init = dw_mci_edmac_init,
>> + .exit = dw_mci_edmac_exit,
>> + .start = dw_mci_edmac_start_dma,
>> + .stop = dw_mci_edmac_stop_dma,
>> + .complete = dw_mci_dmac_complete_dma,
>> .cleanup = dw_mci_dma_cleanup,
>> };
>> -#endif /* CONFIG_MMC_DW_IDMAC */
>>
>> static int dw_mci_pre_dma_transfer(struct dw_mci *host,
>> struct mmc_data *data,
>> @@ -712,7 +823,6 @@ static void dw_mci_post_req(struct mmc_host *mmc,
>>
>> static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
>> {
>> -#ifdef CONFIG_MMC_DW_IDMAC
>> unsigned int blksz = data->blksz;
>> const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
>> u32 fifo_width = 1 << host->data_shift;
>> @@ -720,6 +830,10 @@ static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
>> u32 msize = 0, rx_wmark = 1, tx_wmark, tx_wmark_invers;
>> int idx = (sizeof(mszs) / sizeof(mszs[0])) - 1;
>>
>> + /* pio should ship this scenario */
>> + if (!host->use_dma)
>> + return;
>> +
>> tx_wmark = (host->fifo_depth) / 2;
>> tx_wmark_invers = host->fifo_depth - tx_wmark;
>>
>> @@ -748,7 +862,6 @@ static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
>> done:
>> fifoth_val = SDMMC_SET_FIFOTH(msize, rx_wmark, tx_wmark);
>> mci_writel(host, FIFOTH, fifoth_val);
>> -#endif
>> }
>>
>> static void dw_mci_ctrl_rd_thld(struct dw_mci *host, struct mmc_data *data)
>> @@ -835,7 +948,11 @@ static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data)
>> mci_writel(host, INTMASK, temp);
>> spin_unlock_irqrestore(&host->irq_lock, irqflags);
>>
>> - host->dma_ops->start(host, sg_len);
>> + if (host->dma_ops->start(host, sg_len)) {
>> + /* We can't do DMA */
>> + dev_err(host->dev, "%s: failed to start DMA.\n", __func__);
>> + return -ENODEV;
>> + }
>>
>> return 0;
>> }
>> @@ -2256,26 +2373,30 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
>>
>> }
>>
>> -#ifdef CONFIG_MMC_DW_IDMAC
>> - /* Handle DMA interrupts */
>> - if (host->dma_64bit_address == 1) {
>> - pending = mci_readl(host, IDSTS64);
>> - if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
>> - mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI |
>> - SDMMC_IDMAC_INT_RI);
>> - mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
>> - host->dma_ops->complete(host);
>> - }
>> - } else {
>> - pending = mci_readl(host, IDSTS);
>> - if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
>> - mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI |
>> - SDMMC_IDMAC_INT_RI);
>> - mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
>> - host->dma_ops->complete(host);
>> + if (host->use_dma == TRANS_MODE_IDMAC) {
>> + /* Handle DMA interrupts */
>> + if (host->dma_64bit_address == 1) {
>> + pending = mci_readl(host, IDSTS64);
>> + if (pending & (SDMMC_IDMAC_INT_TI |
>> + SDMMC_IDMAC_INT_RI)) {
>> + mci_writel(host, IDSTS64,
>> + SDMMC_IDMAC_INT_TI |
>> + SDMMC_IDMAC_INT_RI);
>> + mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
>> + host->dma_ops->complete((void *)host);
>> + }
>> + } else {
>> + pending = mci_readl(host, IDSTS);
>> + if (pending & (SDMMC_IDMAC_INT_TI |
>> + SDMMC_IDMAC_INT_RI)) {
>> + mci_writel(host, IDSTS,
>> + SDMMC_IDMAC_INT_TI |
>> + SDMMC_IDMAC_INT_RI);
>> + mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
>> + host->dma_ops->complete((void *)host);
>> + }
>> }
>> }
>> -#endif
>>
>> return IRQ_HANDLED;
>> }
>> @@ -2391,19 +2512,28 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
>> mmc->max_seg_size = host->pdata->blk_settings->max_seg_size;
>> } else {
>> /* Useful defaults if platform data is unset. */
>> -#ifdef CONFIG_MMC_DW_IDMAC
>> - mmc->max_segs = host->ring_size;
>> - mmc->max_blk_size = 65536;
>> - mmc->max_seg_size = 0x1000;
>> - mmc->max_req_size = mmc->max_seg_size * host->ring_size;
>> - mmc->max_blk_count = mmc->max_req_size / 512;
>> -#else
>> - mmc->max_segs = 64;
>> - mmc->max_blk_size = 65536; /* BLKSIZ is 16 bits */
>> - mmc->max_blk_count = 512;
>> - mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
>> - mmc->max_seg_size = mmc->max_req_size;
>> -#endif /* CONFIG_MMC_DW_IDMAC */
>> + if (host->use_dma == TRANS_MODE_IDMAC) {
>> + mmc->max_segs = host->ring_size;
>> + mmc->max_blk_size = 65536;
>> + mmc->max_seg_size = 0x1000;
>> + mmc->max_req_size = mmc->max_seg_size * host->ring_size;
>> + mmc->max_blk_count = mmc->max_req_size / 512;
>> + } else if (host->use_dma == TRANS_MODE_EDMAC) {
>> + mmc->max_segs = 64;
>> + mmc->max_blk_size = 65536;
>> + mmc->max_blk_count = 65535;
>> + mmc->max_req_size =
>> + mmc->max_blk_size * mmc->max_blk_count;
>> + mmc->max_seg_size = mmc->max_req_size;
>> + } else {
>> + /* TRANS_MODE_PIO */
>> + mmc->max_segs = 64;
>> + mmc->max_blk_size = 65536; /* BLKSIZ is 16 bits */
>> + mmc->max_blk_count = 512;
>> + mmc->max_req_size =
>> + mmc->max_blk_size * mmc->max_blk_count;
>> + mmc->max_seg_size = mmc->max_req_size;
>> + }
>> }
>>
>> if (dw_mci_get_cd(mmc))
>> @@ -2437,6 +2567,21 @@ static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
>> static void dw_mci_init_dma(struct dw_mci *host)
>> {
>> int addr_config;
>> + int trans_mode;
>> + struct device *dev = host->dev;
>> + struct device_node *np = dev->of_node;
>> +
>> + /* Check tansfer mode */
>> + trans_mode = (mci_readl(host, HCON) >> 16) & 0x3;
>> + if (trans_mode == 0) {
>> + trans_mode = TRANS_MODE_IDMAC;
>> + } else if (trans_mode == 1 || trans_mode == 2) {
>> + trans_mode = TRANS_MODE_EDMAC;
>> + } else {
>> + trans_mode = TRANS_MODE_PIO;
>> + goto no_dma;
>> + }
>> +
>> /* Check ADDR_CONFIG bit in HCON to find IDMAC address bus width */
>> addr_config = (mci_readl(host, HCON) >> 27) & 0x01;
>>
>> @@ -2462,10 +2607,19 @@ static void dw_mci_init_dma(struct dw_mci *host)
>> }
>>
>> /* Determine which DMA interface to use */
>> -#ifdef CONFIG_MMC_DW_IDMAC
>> - host->dma_ops = &dw_mci_idmac_ops;
>> - dev_info(host->dev, "Using internal DMA controller.\n");
>> -#endif
>> + if (trans_mode == TRANS_MODE_IDMAC) {
>> + host->dma_ops = &dw_mci_idmac_ops;
>> + dev_info(host->dev, "Using internal DMA controller.\n");
>> + } else {
>> + /* TRANS_MODE_EDMAC: check dma bindings again */
>> + if ((of_property_count_strings(np, "dma-names") < 0) ||
>> + (!of_find_property(np, "dmas", NULL))) {
>> + trans_mode = TRANS_MODE_PIO;
>> + goto no_dma;
>> + }
>> + host->dma_ops = &dw_mci_edmac_ops;
>> + dev_info(host->dev, "Using external DMA controller.\n");
>> + }
>>
>> if (!host->dma_ops)
>> goto no_dma;
>> @@ -2482,12 +2636,12 @@ static void dw_mci_init_dma(struct dw_mci *host)
>> goto no_dma;
>> }
>>
>> - host->use_dma = 1;
>> + host->use_dma = trans_mode;
>> return;
>>
>> no_dma:
>> dev_info(host->dev, "Using PIO mode.\n");
>> - host->use_dma = 0;
>> + host->use_dma = trans_mode;
>> return;
>> }
>>
>> @@ -2570,10 +2724,9 @@ static bool dw_mci_reset(struct dw_mci *host)
>> }
>> }
>>
>> -#if IS_ENABLED(CONFIG_MMC_DW_IDMAC)
>> - /* It is also recommended that we reset and reprogram idmac */
>> - dw_mci_idmac_reset(host);
>> -#endif
>> + if (host->use_dma == TRANS_MODE_IDMAC)
>> + /* It is also recommended that we reset and reprogram idmac */
>> + dw_mci_idmac_reset(host);
>>
>> ret = true;
>>
>> @@ -2958,6 +3111,9 @@ EXPORT_SYMBOL(dw_mci_remove);
>> */
>> int dw_mci_suspend(struct dw_mci *host)
>> {
>> + if (host->use_dma && host->dma_ops->exit)
>> + host->dma_ops->exit(host);
>> +
>> return 0;
>> }
>> EXPORT_SYMBOL(dw_mci_suspend);
>> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
>> index 5be9767..9ed6257 100644
>> --- a/include/linux/mmc/dw_mmc.h
>> +++ b/include/linux/mmc/dw_mmc.h
>> @@ -16,6 +16,7 @@
>>
>> #include <linux/scatterlist.h>
>> #include <linux/mmc/core.h>
>> +#include <linux/dmaengine.h>
>>
>> #define MAX_MCI_SLOTS 2
>>
>> @@ -40,6 +41,17 @@ enum {
>>
>> struct mmc_data;
>>
>> +enum {
>> + TRANS_MODE_PIO = 0,
>> + TRANS_MODE_IDMAC,
>> + TRANS_MODE_EDMAC
>> +};
>> +
>> +struct dw_mci_dma_slave {
>> + struct dma_chan *ch;
>> + enum dma_transfer_direction direction;
>> +};
>> +
>> /**
>> * struct dw_mci - MMC controller state shared between all slots
>> * @lock: Spinlock protecting the queue and associated data.
>> @@ -153,11 +165,16 @@ struct dw_mci {
>> dma_addr_t sg_dma;
>> void *sg_cpu;
>> const struct dw_mci_dma_ops *dma_ops;
>> -#ifdef CONFIG_MMC_DW_IDMAC
>> + /* For idmac */
>> unsigned int ring_size;
>> -#else
>> +
>> + /* For edmac */
>> + struct dw_mci_dma_slave *dms;
>> + /* Registers's physical base address */
>> + void *phy_regs;
>> +
>> struct dw_mci_dma_data *dma_data;
>> -#endif
>> +
>> u32 cmd_status;
>> u32 data_status;
>> u32 stop_cmdr;
>> @@ -210,8 +227,8 @@ struct dw_mci {
>> struct dw_mci_dma_ops {
>> /* DMA Ops */
>> int (*init)(struct dw_mci *host);
>> - void (*start)(struct dw_mci *host, unsigned int sg_len);
>> - void (*complete)(struct dw_mci *host);
>> + int (*start)(struct dw_mci *host, unsigned int sg_len);
>> + void (*complete)(void *host);
>> void (*stop)(struct dw_mci *host);
>> void (*cleanup)(struct dw_mci *host);
>> void (*exit)(struct dw_mci *host);
>> --
>> 2.3.7
>>
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>> the body of a message to majordomo@...r.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
>
--
Shawn Lin
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists