| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAGb2v64E-gQu1U_qi2fTWiCmfgMdMR4X6yLUerV21d3E1uQ1cw@mail.gmail.com>
Date: Sat, 19 Sep 2015 00:41:07 +0800
From: Chen-Yu Tsai <wens@...e.org>
To: Maxime Ripard <maxime.ripard@...e-electrons.com>
Cc: Mike Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...eaurora.org>,
linux-arm-kernel <linux-arm-kernel@...ts.infradead.org>,
Chen-Yu Tsai <wens@...e.org>,
Hans de Goede <hdegoede@...hat.com>,
linux-clk <linux-clk@...r.kernel.org>,
linux-kernel <linux-kernel@...r.kernel.org>,
linux-sunxi <linux-sunxi@...glegroups.com>
Subject: Re: [PATCH 5/5] ARM: sun5i: Add C.H.I.P DTS
On Fri, Sep 18, 2015 at 4:48 PM, Maxime Ripard
<maxime.ripard@...e-electrons.com> wrote:
> The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
> RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
> and two connectors to plug additional boards on top of it.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@...e-electrons.com>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/sun5i-r8-chip.dts | 261 ++++++++++++++++++++++++++++++++++++
> 2 files changed, 263 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/sun5i-r8-chip.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b276174b670a..7efd37b907f1 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -599,7 +599,8 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> sun5i-a13-inet-98v-rev2.dtb \
> sun5i-a13-olinuxino.dtb \
> sun5i-a13-olinuxino-micro.dtb \
> - sun5i-a13-utoo-p66.dtb
> + sun5i-a13-utoo-p66.dtb \
> + sun5i-r8-chip.dtb
> dtb-$(CONFIG_MACH_SUN6I) += \
> sun6i-a31-app4-evb1.dtb \
> sun6i-a31-colombus.dtb \
> diff --git a/arch/arm/boot/dts/sun5i-r8-chip.dts b/arch/arm/boot/dts/sun5i-r8-chip.dts
> new file mode 100644
> index 000000000000..6cb3c4f1cd61
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun5i-r8-chip.dts
> @@ -0,0 +1,261 @@
> +/*
> + * Copyright 2015 Free Electrons
> + * Copyright 2015 NextThing Co
> + *
> + * Maxime Ripard <maxime.ripard@...e-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun5i-a13.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "NextThing C.H.I.P.";
> + compatible = "nextthing,chip", "allwinner,sun5i-r8";
> +
> + aliases {
> + i2c0 = &i2c0;
> + i2c1 = &i2c1;
> + i2c2 = &i2c2;
> + serial0 = &uart1;
> + serial1 = &uart3;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + dram_vcc: dram_vcc {
> + compatible = "regulator-fixed";
> + regulator-name = "dram-vcc";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <1600000>;
> + vin-supply = <&ipsout>;
> + regulator-always-on;
> + };
Do we need this if it's not controllable?
> +
> + ipsout: ipsout {
> + compatible = "regulator-fixed";
> + regulator-name = "ipsout";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
This isn't needed. What we might want is a proper representation
of the AXP209's power supply.
> +
> + usb0_vbus: usb0_vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&chip_vbus_pin>;
> +
> + regulator-name = "vbus-usb0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_5v0>;
> + gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */
> + enable-active-high;
> + };
> +
> + vcc_3v3: vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ipsout>;
> + regulator-always-on;
> + };
> +
> + vcc_5v0: vcc5v0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&ipsout>;
> + regulator-always-on;
> + };
We have these in sunxi-common-regulators.dtsi.
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins_a>;
> + status = "okay";
> +
> + axp209: pmic@34 {
> + reg = <0x34>;
> +
> + /*
> + * The interrupt is routed through the "External Fast
> + * Interrupt Request" pin (ball G13 of the module)
> + * directly to the main interrupt controller, without
> + * any other controller interfering.
> + */
> + interrupts = <0>;
> + };
> +};
> +
> +#include "axp209.dtsi"
> +
> +/*
> + * i2c1 is routed to the external pins and doesn't have any device
> + * attached to it on the C.H.I.P itself.
> + */
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins_a>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + status = "okay";
> +
> + xio: gpio@38 {
> + compatible = "nxp,pcf8574a";
> + reg = <0x38>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-parent = <&pio>;
> + interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>;
> + vmmc-supply = <&vcc_3v3>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&otg_sram {
> + status = "okay";
> +};
> +
> +&pio {
> + chip_vbus_pin: chip_vbus_pin@0 {
> + allwinner,pins = "PB10";
> + allwinner,function = "gpio_out";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + chip_id_det_pin: chip_id_det_pin@0 {
> + allwinner,pins = "PG2";
> + allwinner,function = "gpio_in";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +};
> +
> +®_dcdc2 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "cpuvdd";
> + regulator-always-on;
> +};
> +
> +®_dcdc3 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-name = "corevdd";
> + regulator-always-on;
> +};
> +
> +®_ldo1 {
> + regulator-name = "rtcvdd";
> +};
> +
> +®_ldo2 {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <3300000>;
Maybe just fix this to 3.0V?
> + regulator-name = "avcc";
> + regulator-always-on;
> +};
> +
> +®_ldo5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-1v8";
A comment here saying this is found on the header, and to be used
by overlays would be nice.
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins_b>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins_a>,
> + <&uart3_pins_cts_rts_a>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usbphy {
> + pinctrl-names = "default";
> + pinctrl-0 = <&chip_id_det_pin>;
> + status = "okay";
> +
> + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
Better leave a comment here saying VBUS detection requires AXP209
usb-power-supply support.
> +
> + usb0_vbus-supply = <&usb0_vbus>;
> + usb1_vbus-supply = <&vcc_5v0>;
> +};
> --
> 2.5.1
>
Thanks!
ChenYu
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists